Maytag Neptune Washer User Manual

MAH-3

MAYTAG NEPTUNE® WASHER

USE & CARE

G U I D E

TABLE OF	CONTENTS
Safety Instructions ................................................		1-2
Operating Instructions ............................................		3
Using the Controls ..............................................		4-8
Water Use .................................................................		8
Detergent Use ..........................................................		9
Features ................................................................		9-10
Care and Cleaning .................................................		11
Storing the Washer ................................................		12
Troubleshooting ...............................................		12-14
Warranty ..................................................................		15
Guide d’utilisation et d’entretien .......................		16
Guía de Uso y Cuidado ........................................		32

A/12/04

Part No. DC68-02030B

©2004 Maytag Appliances Sales Co.

WELCOME

Welcome and congratulations on your pur- chase of a Maytag Neptune® washer! Your complete satisfaction is very important to us. For best results, we suggest reading this material to help acquaint you with proper operating and maintenance procedures.

Should you need assistance in the future, it is helpful to:

1) Have complete model and serial number identification of your washer.

Date of Purchase ____________________

Model Number ______________________

Serial Number ______________________

2)IMPORTANT: Keep this guide and the sales receipt in a safe place for future reference. Proof of original purchase date is needed for warranty service.

If you have questions, call:

Maytag Customer Assistance 1-800-688-9900 USA 1-800-688-2002 CANADA (Mon.–Fri., 8am–8pm Eastern Time) Internet: http://www.maytag.com

U.S.A. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

NOTE: In our continuing effort to improve the quality of our appliances, it may be necessary to make changes to the appliance without revising this guide.

For service and warranty information, see page 15.

IMPORTANT SAFETY INSTRUCTIONS

read before operating your washer

WHAT YOU NEED TO KNOW ABOUT

SAFETY INSTRUCTIONS

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining or operating appliance.

Always contact your manufacturer about problems or conditions you do not understand.

RECOGNIZE SAFETY SYMBOLS, WORDS, LABELS

WARNING

WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION

CAUTION – Hazards or unsafe practices which COULD result in minor personal injury or property damage.

SAVE THESE INSTRUCTIONS

1

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock or injury to persons when using the appliance, follow basic precautions, including the following:

1.Read all instructions before using the appliance.

2.As with any equipment using electricity and having moving parts, there are potential hazards. To use this appliance safely, the operator should become familiar with the instructions for operation of the appliance and always exercise care when using it.

3.Do not install or store this appliance where it will be exposed to the weather.

4.Install and level the clothes washer on a floor that can support the weight.

5.This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance.

6.To avoid the possibility of fire or explosion:

•Do not wash items that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode. Hand wash and line dry any items containing these substances.

Any material on which you have used a cleaning solvent, or which is saturated with flammable liquids or solids, should not be placed in the clothes washer until all traces of these liquids or solids and their fumes have been removed.

These items include acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes and wax removers.

•Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

•Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

7.Unplug power supply cord before attempting to service your clothes washer.

8.Do not reach into the appliance if the tumbler is moving.

9.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

10.Do not tamper with controls.

11.Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in published user-repair instructions that you understand and have the skills to carry out.

12.Store laundry aids and other material in a cool, dry place where children cannot reach them.

13.Do not wash or dry items that are soiled with vegetable or cooking oil.These items may contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

14.Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash. Hazardous fumes can form.

15.Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and cause skin irritation.

16.Before the appliance is removed from service or discarded, remove the door to the washing compartment.

17.Do not sit on top of the clothes washer.

18.Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks, cuts, wear or leaks and replace them every five years.

2

OPERATING INSTRUCTIONS

For detailed information on sorting, pretreating stains, etc., see the enclosed Laundering Tips booklet.

LOAD THE CLOTHES WASHER

•The tub can be loaded completely full with dry, unfolded clothes. However, DO NOT pack the tub tightly.

•Overloading may reduce washing efficiency, cause excess wear and possibly cause creasing or wrinkling of the load.

•Wash delicate items such as bras, hosiery and other lingerie in the Delicates or Hand Wash (select models) cycle with similar lightweight items.

•When washing big bulky items or a couple of small items that do not fill the tub completely, such as a rug, a few towels should be added for improved tumbling and spin performance.

•When washing smaller, bulky items that do not fill the tub completely such as a rug, one pillow, stuffed toys or one or two sweaters, a few towels should be added for improved tumbling and spin performance.

•When washing heavily soiled loads, it is very important to avoid overloading the washer to assure good cleaning results.

•To add a forgotten item in the Super Wash, Normal, Whites (select models), Colors (select models),Wrinkle Control or Quick Wash cycles, press the Cycle Selector dial, wait for the Door Lock light to go out (5 seconds), add the item, close the door and press the Cycle Selector dial. After a pause of one to two minutes, the cycle will resume.

•Close door carefully to avoid slamming.

NOTE: To ensure that your additional items get clean, do not wait more than five minutes after the cycle has started to add the item.

GETTING STARTED

1.Load the washer loosely – DO NOT overload.

2.Close the door.

3.Add detergent and additives to the dispenser (see pages 9-10).

4.Select the appropriate cycle and options for the load, (see pages 4-7).

5.Press the Cycle Selector dial.

6.The Wash Indicator light will illuminate.

7.The estimated cycle time will appear in the display. The time may fluctuate to better indicate the wash time remaining in the cycle.

8.Before the washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain.

NOTES:

• When the cycle is complete, the Door Lock light will go out and “End” or “00” (select models) will appear in the display.

• DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see “Load the Clothes Washer” section.

• When the washer is restarted after a pause, there will be a delay of up to 15 seconds before the cycle will continue.

• Pressing Power Off cancels the cycle and stops the washer.

• The Wash, Rinse and Spin indicator lights will illuminate during those portions of the cycle.

3

USING THE CONTROLS

Control features vary by model.

Step 1

SELECT CYCLE

Select the appropriate cycle for the type of load.

This will determine the tumble pattern and spin speed for the cycle.

NOTE: To minimize wrinkling of loads, select the Wrinkle Control cycle.

Sanitary (select models) – For heavily soiled, colorfast garments. This cycle heats the water to 150°F to eliminate bacteria.

NOTE: If Pause is selected during the heating portion of the Sanitary Cycle, the washer door will remain locked for your safety.

Super Wash – For sturdy, colorfast fabrics and heavily soiled garments.

Normal – For most fabrics including cottons, linens and normally soiled garments.

Whites (select models) – For white fabrics with or without bleach.

Wrinkle Control – For “wash and wear” and synthetic fabrics and lightly to normally soiled garments.

Colors (select models) – For bright fabrics or fabrics that may bleed.

Delicates – For sheer fabrics, bras and lingerie.

Hand Wash – For wool, silk and other hand-wash-only fabrics.

For best results, use liquid detergent.

Quick Wash – For lightly soiled or wrinkled garments needed quickly.

Enviro Plus (select models) – For geographic areas where energy and water conservation is needed.

4

USING THE CONTROLS

Control features vary by model.

Step 2

SELECT WASH/RINSE WATER TEMPERATURES

Press the arrow pad to select the wash and rinse water temperatures. Follow

the garment care label and chart below for best results.

Sanitary/Cold (select models) – Heavily soiled, colorfast items. Only available with the Sanitary cycle.

Hot/Cold – Whites and heavily soiled color-fast items.

ATC Warm/Warm – Color-fast items.When warm rinse is selected, only the final rinse will be warm.The other rinses will be cold to conserve energy.

ATC Warm/Cold – Moderately soiled, color-fast items; most wrinkle free items.

ATC Cold/Cold – Brightly colored, lightly soiled items.

Cold/Cold – Brightly colored, very lightly soiled items; washable woolens.

IMPORTANT: The washer features an automatic temperature control (ATC) to provide a warm wash of approximately 105˚ F, a cold wash of approximately 65˚ F and a warm rinse of approximately 80º F in the final rinse only on the ATC temperature selections.

REMEMBER: In wash water temperatures below 65˚ F, detergents do not dissolve well or clean well.

Step 3

SELECT SPIN SPEED

Press the arrow pad to select the spin speed.

Max Extract or Max Extract Plus (select models) – Use for heavy loads such as towels and bedding. Removes more water from loads during spin.

FABRICS NOTE: To minimize wrinkling of wrinkle free and no-iron fabrics, do not use the Max Extract or Max Extract Plus spin option for these loads. Also, DO NOT overload the washer.

High (select models) – Use for underwear, t-shirts, jeans and sturdy cottons.

Medium – Use for jeans, wrinkle free or “wash-and-wear” items and synthetics.

Gentle – Use for items that will be hung up or laid flat to dry.

Low – Use for delicate items needing a slow spin speed because of fabric and construction.

Drain Only (select models) – Drains the washer without spinning. Use for extremely delicate items that cannot tolerate any spin.

5

USING THE CONTROLS

Control features vary by model.

Step 4

SELECT SOIL LEVEL

Press the arrow pad to select the Soil Level/washing time. Heavy – Use for cleaning heavily soiled loads.

Medium – Use for cleaning moderately soiled loads.This setting will be appropriate for most loads.

Light – Use for cleaning lightly soiled loads.

Step 5

SELECT CYCLE OPTIONS

Press the appropriate pad(s) to select one or more options.The indicator light above the pad will illuminate when the option is selected.

Delay – Any cycle can be delayed for up to 9, 12 or 19 hours (select models) in one hour increments.

1.Make the appropriate selections for your load.

2.Press the Delay pad until the desired delay time appears in the display.

3.Press the Cycle Selector dial.The delay time will start counting down.

4.To cancel a delay, press the Power Off pad and restart.

Chime – Press the Chime pad to increase or decrease the end of cycle signal volume or turn the signal off.

Control Lock – The washer controls can be locked to prevent unwanted use by children.

1. Press the Wash/Rinse Temp and Spin Speed pads at the same time for three seconds.

2.The Control Lock light will illuminate.

3.To unlock, press the Wash/Rinse Temp and Spin Speed pads at the same time for three seconds.The Control Lock light will go out.

cont.

6

USING THE CONTROLS

Control features vary by model.

SELECT CYCLE OPTIONS, CONT.

Press the appropriate pad(s) to select one or more options.The indicator light above the pad will illuminate when the option is selected.

Prewash (select models) – Can be selected with any cycle.Add detergent to the prewash section of the detergent compartment.Washer fills with cold water and detergent, tumbles for 25 minutes, then drains and advances to the selected cycle.

Stain Treat (select models) – Adds 5 minutes to the wash for better stain removal.

Extra Rinse – Adds an additional rinse at the end of the cycle to more thoroughly remove laundry additives and perfumes.

Extended Spin (select models) – Adds additional time to the spin to remove more water from the load.

Rinse and Spin – Use for loads that need rinsing only or to add rinse-added fabric softener to a load.

Spin Only – Provides a spin to remove more water from the load.

Step 6

START THE WASHER

To start the washer, press the Cycle Selector dial. Before the washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain.

Changing a Cycle

If an incorrect cycle has been accidentally selected:

1. Press the Cycle Selector dial.

2.Turn the Cycle Selector dial to the desired cycle. 3. Set the desired options for the cycle.

4. Press the Cycle Selector dial.The Wash indicator lights stop flashing and the new cycle starts.

Canceling a Cycle

To cancel a cycle:

1. Press the Power Off pad.

2.Select the Rinse and Spin or Spin Only option pad.

3.Press the Cycle Selector dial.The Spin light illuminates and the washer starts the rinse or spin.

7

USING THE CONTROLS

Control features vary by model.

ESTIMATED TIME DISPLAY (SELECT MODELS)

After setting the cycle and pressing Cycle Selector dial, the display will show the esti- mated minutes remaining in the cycle.The estimated time remaining may fluctuate to better indicate the wash time left in the cycle.

INDICATOR LIGHTS

Door Lock – lights whenever the door of the clothes washer is locked.The door can be unlocked by pressing the Cycle Selector dial to pause the washer.

Control Lock – The washer controls can be locked to prevent unwanted use by children.

1. Press the Wash/Rinse Temp and Spin Speed pads at the same time for three seconds.

2.The Control Lock light will illuminate.

3.To unlock, press the Wash/Rinse Temp and Spin Speed pads at the same time for three seconds.The Control Lock light will go out.

Cycle Indicator Lights – The Wash, Rinse and Spin lights at the top of the control panel will illuminate progressively to indicate when the washer is in those portions of the cycle.These lights will flash when the cycle has been paused.

Pad Indicator Lights – The indicator lights above the pads will illuminate when the pad is selected.

Cycle Setting Indicator Lights – Indicator lights by the cycle settings will illuminate when the selection is made.

WATER USE

INTELLIFILLTM WATER LEVEL CONTROL

The amount of water used will vary with each load.The Maytag Neptune® clothes washer will automatically provide the appropriate amount of water for efficient cleaning performance and conservation of water and energy. Fill time will vary depending on water pressure.

8

DETERGENT USE

Your Maytag Neptune® washer is designed to use high efficiency (HE) detergents.

•For best cleaning results, use a high

efficiency detergent such as Tide HE,Wisk HE, Cheer HE or Gain HE*. High efficiency detergents contain suds suppressors which reduce or eliminate suds. When less suds are produced, the load tumbles more efficiently and cleaning results are maximized.

If HE detergent is not available, regular detergent may be used.

FEATURES

AUTOMATIC DISPENSER

The washer has separate compartments for dispensing detergent and color-safe bleach, chlorine bleach and fabric softener. All laundry additives are added to their respective compartments before starting the washer.

The Automatic Dispenser MUST ALWAYS be in place before starting the washer. DO NOT open the Automatic Dispenser when the washer is running.

To use:

1. Pull out the dispenser drawer on the left side of the control panel.

2. Fill appropriate compartments with laundry additives, being careful not to overfill or spill additives.

3. Slide the dispenser drawer carefully and completely back into the compartment.

DETERGENT COMPARTMENT

1.Pour the recommended amount of laundry detergent directly into the detergent compartment before starting the washer.

2.If color-safe bleach is to be used, it should be added with detergent to the detergent compartment.

•When adding color-safe bleach with detergent, it is best if both laundry products are in the same form; granular or liquid.

NOTE: If using liquid detergent, lower the
Detergent Selector and add the detergent to the
Detergent Compartment.	9

• If using regular detergent formulated for toploading washers, it is important to pay close attention to the soil level of the load, load size, and water hardness**. To avoid over-suds- ing, which interferes with tumbling, rinsing and spinning and causes extended cycle times, reduce the amount of detergent used with soft water or with small or lightly soiled loads.

NOTE: Reducing the amount of detergent may reduce cleaning. It is important to pretreat stains, sort carefully by color and soil level and avoid overloading.

*Brand names are trademarks of the respective manufacturers.

**To determine water hardness in your area, contact your local water utility or State University Extension office in your area.

Prewash (select models)

Detergent

Selector

Detergent	POWDER	LIQUID	SOFTENER
Compartment	UP FOR	DOWN FOR	BLEACH

PREWASH COMPARTMENT (SELECT MODELS)

When using the Prewash option (select models), detergent should be added to both the Prewash Compartment and the Detergent Compartment.The detergent will be automatically dispensed during prewash.

• If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Prewash

Compartment and 2/3 of the recommended amount to the Detergent Compartment.

• If regular detergent is used, add 1/6 of the recommended amount to the Prewash Compartment and 1/3 of the recommended amount to the Detergent Compartment.

FEATURES

BLEACH COMPARTMENT

(Liquid Chlorine Bleach Only)

1. Add chlorine bleach to the Bleach

Compartment. DO NOT exceed the MAX FILL line.

2. Avoid splashing or over-filling the compartment.

3.The washer automatically dispenses bleach into the tub at the appropriate time.

4.The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load.

NOTES:

• Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly.

• If you prefer to use color-safe, non-chlorine bleach, add it to the appropriate detergent compartment. DO NOT pour color-safe bleach into the chlorine bleach dispenser.

			Bleach
			Compartment
UP FOR	DOWN FOR	SOFTENER	Fabric Softener
		BLEACH	Compartment
POWDER	LIQUID

FABRIC SOFTENER COMPARTMENT

1.Pour the recommended amount of liquid fabric softener into the softener compartment. For smaller loads, use less than one cap full.

2.Fabric softener should be diluted with warm water until it reaches MAX FILL in the compartment.

3.The dispenser automatically releases liquid fabric softener at the proper time during the rinse cycle.

NOTES:

• Use the softener compartment ONLY for liquid fabric softeners.

• DO NOT use the Downy Ball* with this washer. It will not add fabric softener at the appropriate time. Use the automatic dispenser.

* Brand names are trademarks of the respective manufacturers.

10

CARE AND CLEANING

Turn off the water faucets after finishing the day’s washing. This will shut off the water supply to the clothes washer and prevent the unlikely possibility of damage from escaping water. Leave the door open to allow the inside of the washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.

CLEANING THE INTERIOR

Clean the interior of the washer periodically to remove any dirt, soil, odor, mold, mildew or bacteria residue that may remain in the washer as a result of washing clothes. We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior. The frequency with which the washer should be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being run through your washer, or the use of cold water. Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent stains on the washer or washload.

Clean the following as recommended:

Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel.

Cabinet – Clean with soap and water.

To clean and freshen the washer interior:

1. Make a solution of one cup chlorine bleach and two cups warm water. Be careful not to spill or splash the bleach solution.

2. Wipe the door seal with bleach solution and a soft cloth. 3. Fill bleach dispenser with chlorine bleach.

4. Run the washer through a complete cycle using hot water.

5. Repeat the wash cycle if necessary.

Hard water deposits may be removed, if needed. Use a recommended cleaner labeled clothes washer safe.

CLEANING THE DISPENSERS

The Automatic Dispenser may need to be cleaned periodically due to laundry additive buildup.

1. Press the release lever on the inside of the dispenser and pull out.

UP FOR

POWDER

BLEACH

SOFTENER

2. Remove the cups from the fabric softener and
bleach compartments.
3.Wash all of the parts under running water.
4. Clean the dispenser recess with a soft brush.
5. Reinsert the cups, pushing them firmly into
place.
6. Push the dispenser back into place.
7. Run a Rinse & Spin cycle without any load in the
washer.	11

Siphon

Cap

DOWN FOR

LIQUID

STORING THE CLOTHES WASHER

Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare the washer for storage as follows:

• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run the washer through the cycle without a load.

• Turn the water faucets off and disconnect the inlet hoses.

•Disconnect the clothes washer from the electrical supply and leave the washer door open to let air circulate inside the tumbler.

•If the washer has been stored in below-freezing temperatures, allow time for any water left over in the washer to thaw out before use.

For information on long-term storage or storage of your washer during extreme cold temperatures,

call Maytag Customer Service toll-free at 1-800-688-9900 USA or 1-800-688-2002 Canada. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

TROUBLESHOOTING

For problem laundry solutions (i.e. fabric damage, residue, tangling) and special laundry care procedures, see the enclosed Laundering Tips booklet.

	CHECK THESE POINTS IF YOUR MAYTAG NEPTUNE® WASHER...
	Freshening your	•	See Cleaning the Interior, page 11.
	washer
		•	Make sure door is firmly closed.
	The washer will not	•	Make sure the washer is plugged in.
	start	•	Make sure the water source faucets are turned on.
		•	Make sure to press the Cycle Selector dial to start the washer.
		•	Make sure the Control Lock is not activated, see page 6.
		• Before the washer starts to fill, it will make a series of clicking noises to check the door lock
			and do a quick drain.
	No water or insuffi-	•	Turn both faucets on fully.
	cient water supply	•	Make sure the door is tightly closed.
		•	Make sure the washer is plugged in.
		•	Check fuse or reset circuit breaker.
		•	Press the Cycle Selector dial to start the washer.
		•	Straighten water inlet hoses.
		•	Disconnect hoses and clean screens. Hose filter screens may be plugged.
		• Open and close the door, then press the Cycle Selector dial.
	Detergent remains in	•	Make sure the washer is running with sufficient water pressure.
	the automatic dis-
			See Installation Instructions.
	penser after the wash
		•	Make sure the Detergent Selector is in the upper position when using granular detergent.
	cycle is complete
	Washer vibrates or	•	Make sure the washer is set on a level surface. If the surface is not level, adjust the washer
	is too noisy		feet to level the appliance. See Installation Instructions.
		•	Make sure that the shipping bolts are removed. See Installation Instructions.
		•	Make sure the washer is not touching any other object.
		•	Make sure the laundry load is balanced.

CONT.

12

TROUBLESHOOTING

CHECK THESE POINTS IF YOUR MAYTAG NEPTUNE® WASHER...

		•	Plug cord into live electrical outlet.
		•	Check fuse or reset circuit breaker.
		•	Close door and press the Cycle Selector dial to start the washer. For your safety, the washer
	Stops		will not tumble or spin unless the door is closed.
		• Before the washer starts to fill, it will make a series of clicking noises to check the door lock
			and do a quick drain.
		•	This may be a pause or soak period in the cycle.Wait briefly and it may start.
		•	Check screens on inlet hoses at the faucets for obstructions. Clean screens periodically.
		•	Turn both faucets on fully.
	Fills with the	•	Make sure temperature selection is correct.
		•	Make sure hoses are connected to correct faucets. Flush water lines.
	Wrong
		•	Check the water heater. It should be set to deliver a minimum 120° F (49° C) hot water at
	Temperature
	Water		the tap.Also check water heater capacity and recovery rate.
		•	Disconnect hoses and clean screens. Hose filter screens may be plugged.
		•	As the washer is filling, the water temperature may change as the automatic temperature
			control feature checks incoming water temperature.This is normal.
		•	While the washer is filling, you may notice just hot and/or just cold water going through the
			dispenser when cold or warm wash temperatures are selected. This is a normal function of
			the automatic temperature control feature as the washer determines the temperature of the
			water.
	Won’t tumble	•	Check fuse or reset circuit breaker.
		•	Close the door and press the Cycle Selector dial. For your safety, the washer will not
			tumble or spin unless the door is closed.
	Door locked shut;	•	Press the Cycle Selector dial to stop the washer.
		•	The washer door will remain locked during the heating portion of the Sanitary Cycle
	will not open
			(select models).
		•	It may take a few moments for the door lock mechanism to disengage.
	The washer does	•	Check fuse or reset circuit breaker.
	not drain and/or	•	Straighten drain hoses. Eliminate kinked hoses. If there is a drain restriction, call for service.
	spin	•	Close the door and press the Cycle Selector dial. For your safety, the washer will not
			tumble or spin unless the door is closed.
	Load is too wet	•	Use the High or Max Extract spin speed.
		•	Use high efficiency detergent to reduce over-sudsing.
	at end of cycle
		•	Load is too small. Very small loads (one or two items) may become unbalanced and not spin
			out completely.
	Leaks Water	•	Make sure door is firmly closed.
		•	Make sure hose connections are tight.
		•	Make sure end of drain hose is correctly inserted and secured to drain facility.
		•	Avoid overloading.
		•	Use high efficiency detergent to prevent over-sudsing.
	Excessive Suds	•	Use high efficiency detergent to prevent over-sudsing.
		•	Reduce detergent amount for soft water, small or lightly soiled loads.

For further assistance, call Maytag Customer Service toll-free at 1-800-688-9900 USA or 1-800-688-2002 Canada. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

13

TROUBLESHOOTING

INFORMATION CODES
Information codes may be displayed to help you better understand what is occurring with the washer.
Code
Symbol	Meaning	Solution
	Unbalanced load prevented the washer from	Redistribute the load, press the Cycle Selector
	spinning.	dial.
	Door is unlocked when washer is running.	Press Power Off pad then restart the cycle. If the
		code reappears, call for service, see below.
	Door is open when washer is running.	Close the door tightly and restart the cycle.
		If the code reappears, call for service, see below.
	The washer failed to lock the door.	Close the door tightly and restart the cycle.
		If the code reappears, call for service, see below.
	Water temperature control problem.	Call for service, see below.
	(Heater Control problem)
	The washer has tried to fill but has not reached	Call for service, see below.
	the proper water level.
	The door will not unlock.	Make sure the door is firmly closed.
		Push the Power Off pad to turn off the washer, and
		then turn it on using any pad. If the code reappears,
		call for service, see below.
	Motor not running properly.	Restart the cycle pressing the Cycle Selector dial.
		If the code reappears, call for service, see below.
	The washer is not draining.	See Troubleshooting “The washer does not drain
		and/or spin”, page 13. If problem continues, call for
		service, see below.
	The washer has tried to fill but was unsuccessful.	Make sure the water faucets are open all the way.
		Check for kinked hoses.
		Check inlet screens on fill hoses.
	Problem with control.	Call for service, see below.
	Electric service was lost when washer was	Restart the cycle by pressing the Cycle Selector
	running.	dial.

For any codes not listed above, call Maytag Customer Service at 1-800-688-9900 USA or 1-800-688-2002 Canada.

14