Marantz VP-10S1 User Manual

Model MOUNT10 User Guide

VP-10S1 DLP Projector Mount

IMPORTANT SAFETY INSTRUCTIONS

READ BEFORE INSTALLING EQUIPMENT

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.

1.Read instructions - All the safety and operating instructions should be read before the product is operated.

2.Retain instructions - The safety and operating instructions should be retained for future reference.

3.Heed warnings - All warnings on the product and in the operating instructions should be adhered to.

4.Follow instructions - All installation instructions should be followed.

5.Use only the parts provided with the mount, along with any parts (commercially available) that are specified in this manual.

6.Do not modify the mount or the parts provided with the mount.

7.Do not use damaged parts. if any parts become damaged, contact your dealer.

8.All bolts and screws must be tightened securely.

9.Make sure not to block any ventilation openings when installing the projector.

10.Special techniques and experience are required when installing the projector with this mount. Contact your dealer to install the projector for you.

11.Once the projector is installed, safety checks should be conducted on a regular basis.

Warning

The ceiling should be capable of supporting a weight of at least five (5) times the projector(s) weight.

If it cannot, the ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury.

Hardware List

1.	Four (4)	3/8 (inch) nuts	7.		Eight (8) 6 (mm) flat washers
2.	Four (4)	3/8 (inch) flat washers	8.		One (1) Ceiling Mount #1
3.	Two (2)	8 (mm) screws	9.	Two (2) Base Plate Connectors
4.	Fourteen (14) 6 (mm) screws		10.		One (1) Horizontal Tilt Plate #2
5.	Eight (8) 6 (mm) rubber washers		11. One (1) Horizontal Tilt Plate #3
6.	Two (2)	8 (mm) rubber washers	12.		One (1) Projector Plate #4

Adjustment Ranges and Load Allowances

Horizontal Tilt (yaw)	+/-	4 degrees
Vertical Tilt (tilt)	+/-	8 degrees
Rotation	+/- 15 degrees
Lateral Shift	+/- 41/2 inches
Maximum Load Allowance		450 Lbs.

MOUNT10

PROJECTOR MOUNT

INSTALLATION INSTRUCTIONS

Step 1

Base Plate Connectors #1 and Projector Mount Ceiling Plate 1 with ceiling mounting holes #2.

Figure 1
1
	4	Ceiling Wire	4		14"
		Access
2	3			3	2
			2
		8 5/8"
Plate 1

Base Plate Connectors #1 Projector Mount Ceiling Plate 1

Insert Base Plate connectors #1 into the lateral positioning slots

#3 as shown in #4 from the underside of Plate 1. The lateral positioning slots will give you 4 1/2" inches of lateral adjustment for projector alignment.

Step 2

Horizontal Adjustment Plate 2 (Base Plate Connector

Holes #3).

Figure 2
3	3
Wire	10 5/8"
Access
3	3
7 5/8"
Plate 2

Base plate connector holes #3 provide 15 degrees of horizontal adjustment.

Attach horizontal adjustment Plate 2 to projector mount ceiling Plate 1 using the four (4) 3/8" (inch) nuts and washers provided.

MOUNT10 PROJECTOR MOUNT	INSTALLATION INSTRUCTIONS continued
Step 2 B
Horizontal Adjustment Plate 2 (Figure 2) attached to		Step 3 B
Projector Mount Ceiling Plate 1.		Horizontal Tilting Plate 3 Attached to Plates 1 and 2.

Figure 3

Wire

Access

Plates 1 & 2

Install the combined plates (above) securely to the ceiling structure in accordance with local commercial building standards.

Use suitable hardware in adequate quantity and size depending on the installation requirements. (Please note that Projector VP-10S1 weighs 90.3 lbs. (41kgs).

Figure 5
Tilting Capability	Tilting Capability
Plate 3

The newly combined Plate 3 provides 80 degrees of horizontal tilt. When positioned, tighten with screws and washers provided.

Step 3

Horizontal Tilting Plate 3

Figure 4

2	2	3	2	2
1		Wire			1
2		Access
			Indicates Forward		2
			Positioning of Mount
	2	3		2

1Holes for 6mm screws with rubber washer and steel washer

2Holes for 6mm screws with washer

3Holes for 8mm screws with rubber washer and steel washer

Plate 3

Attach Horizontal Tilting Plate 3 to the previously combined plates (already installed on ceiling) using the two (2) 8 (mm) screws with rubber washers, steel washers and four (4) 6 (mm) screws with washers provided, as indicated in Figure 4. Install two (2) 6 (mm) screws with rubber spacers and metal washers into the welded metal studs (indicated #1) Tighten halfway.

Step 4

Projector Mounting Plate 4

Figure 6
	Indicates Forward
	Positioning of Mount
1	1	1
12 1/4"
1	1	1
	17"
1 holes for 6mm screws with rubber washers
Plate 4

Invert the projector and place it on a soft and flat surface. Align the six (6) rubber spacers provided with the six (6) 6 (mm) mounting holes on the projector and secure with the six (6) 6 (mm) screws provided.

continued over

MOUNT10 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued

Step 4 B
Projector Mounting Plate 4 (continued)	Projector Mounting Plate 4 connected to Mounting Plate 3
Figure 7	Figure 8
	Mounts Fully Assembled
Projector Side	Projector Side

80 Tilt

80 Tilt

Ceiling Side

Mount Side

Plate 4

Work in a group of 4 or more to carry the projector and follow manufacturer's guidelines for relocating as stated in the VP-10S1 owner's manual.

Lift and slide the projector onto the 6 (mm) screws previously installed in the metal studs of the plate on the ceiling (see arrow in Figure 7). Tighten the six (mm) screws on both sides of the mount and install four (4) 6 (mm) screws and washers into the side of the projector Mounting Plate 4.

Sequence of Assembly of Projector Mounting Plates

Plate 4

Step 4

Plate 3

Step 3

Plate 2

Step 2

Plate 1

1100 Maplewood Drive

Itasca, IL 60143

Phone: [phone] Fax: [phone]

You can find your nearest authorized distributor or dealer on our website at: www.marantz.com

Printed in Canada

2004