Makita RBC2510, RBC2500 User Manual 2

0 (0)
ISTRUZIONI D’USO
MANUAL DE INSTRUCCIONES
Brush Cutter
Decespugliatore
Desbrozadora
RBC2500
RBC2500
RBC2510
A
English / Italiano / Spanish
Tagliabordi
Cortabordes
RBC2510
INSTRUCTION MANUAL
ISTRUZIONI D’USO
MANUAL DE INSTRUCCIONES
Important:
Read this instruction manual carefully before putting the Brush Cutter/String Trimmer into operation and strictly observe the safety
regulations!
Preserve instruction manual carefully!
Importante:
Prima di mettere in funzione il decespugliatore/tagliabordi, leggere attentamente il presente manuale; rispettare rigorosamente le norme
di sicurezza!
Conservare il manuale delle istruzioni per l’uso!
Importante:
Leer cuidadosamente este manual de instrucciones antes de poner en marcha la máquina y observar estrictamente las normas de
seguridad.
Conservar este manual de instrucciones con cuidado.
1
Thank you very much for purchasing the MAKITA Brush Cutter/String trimmer.
We are pleased to recommend to you the MAKITA Brush Cutter/String trimmer
which is the result of a long development programme and many years of
knowledge and experience.
Please read this booklet which refers in detail to the various points that will
demonstrate its outstanding performance. This will assist you to obtain the
best possible result from your MAKITA Brush Cutter/String trimmer.
Table of Contents Page
Symbols ...................................................................... 1
Safety instructions ..................................................... 2
Technical data ............................................................ 6
Designation of parts ................................................... 7
Assembly of engine and shaft ................................... 8
Mounting of handle ..................................................... 9
Mounting of protector ............................................... 10
Mounting of cutter blade or nylon cutting head ......... 11
Fuels / Refuelling ...................................................... 12
Correct handling of machine ..................................... 13
Points in operation and how to stop ......................... 13
Resharpening the cutting tool ................................... 14
Servicing instructions ............................................... 16
Storage ..................................................................... 18
Take Particular care and Attention
Read instruction Manual
Forbidden
No Smoking
No open flame
Protective gloves must be worn
Keep the area of operation clear of all
persons and pets
Wear eye and ear protection
(for String trimmer only)
Wear protective helmet, eye and ear
protection (for Brush Cutter only)
Engine-Manual start
Top permissible tool speed
Emergency stop
ON/START
OFF/STOP
Flying object hazard
Keep distance
Kickback
Do not use metal blades
(for String trimmer only)
Recycling
Fuel and oil mixture
First Aid
You will note the following symbols when reading the instructions manual.
SYMBOLS
Wear sturdy boots with nonslip soles.
Steeltoed safety boots are recommended.
English
2
SAFETY INSTRUCTIONS
General Instructions
To ensure correct operation, user has to read this instruction manual to make
himself familiar with the handling of the Brush Cutter/String trimmer. Users
insufficiently informed will risk danger to themselves as well as others due to
improper handling.
It is recommended only to lend the Brush Cutter/String trimmer to people who
have proven to be experienced with Brush Cutter/String trimmers.
Always hand over the instruction manual.
First users should ask the dealer for basic instructions to familiarize oneself
with the handling of an engine powered cutter.
Children and young persons aged under 18 years must not be allowed to
operate the Brush Cutter/String trimmer. Persons over the age of 16 years
may however use the device for the purpose of being trained only whilst
under supervision of a qualified trainer.
Use Brush Cutter/String trimmers with the utmost care and attention.
Operate the Brush Cutter/String trimmer only if you are in good physical
condition. Perform all work calmly and carefully. The user has to accept
liability for others.
Never use the Brush Cutter/String trimmer after consumption of alcohol or
drugs, or if feeling tired or ill.
Intended use of the machine
The Brush Cutter/String trimmer is only intended for cutter grass, weeds,
Bushes, undergrowth it should not be used for any other purpose such as
Edging or hedge cutting as this may cause injury.
Personal protective equipment
The clothing worn should be functional and appropriate, i.e. it should be tight-
fitting but not cause hindrance. Do not wear either jewelry or clothing which
could become entangled with bushes or shrubs.
In order to avoid either head-, eye-, hand-or foot injuries as well as to protect
your hearing the following protective equipment and protective clothing must
be used during operation of the Brush Cutter/String trimmer.
Always wear a helmet where there is a risk of falling objects. The protec-
tive helmet (1) is to be checked at regular intervals for damage and is to be
replaced at the latest after 5 years. Use only approved protective helmets.
The visor (2) of the helmet (or alternatively goggles) protects the face from
flying debris and stones. During operation of the Brush Cutter/String trimmer
always wear goggles, or a visor to prevent eye injuries.
Wear adequate noise protection equipment to avoid hearing impairment (ear
muffs (3), ear plugs etc.).
The work overalls (4) protect against flying stones and debris.
We strongly recommend that the user wears work overalls.
Special gloves (5) made of thick leather are part of the prescribed equipment
and must always be worn during operation of the Brush Cutter/String
trimmer.
When using the Brush Cutter/String trimmer, always wear sturdy shoes (6)
with a non-slip sole. This protects against injuries and ensures a good
footing.
Starting up the brush cutter
Please make sure that there are no children or other people within a working
range of 15 meters (49ft), also pay attention to any animals in the working
vicinity.
Before use always check that the Brush Cutter/String trimmer is safe for
operation:
Check the security of the cutting tool, the control lever for easy action and
check for proper functioning of the control lever lock.
Rotation of the cutting tool during idling speed is not allowed. Check with
your dealer for adjustment if in doubt. Check for clean and dry handles and
test the function of the start/stop switch.
3
Start the Brush Cutter/String trimmer only in accordance with the instructions.
Do not use any other methods for starting the engine!
Use the Brush Cutter/String trimmer and the tools only for such applications
as specified.
Only start the Brush Cutter/String trimmer engine, after the entire assembly is
done. Operation of the device is only permitted after all the appropriate
accessories are attached!
Before starting make sure that the cutting tool has no contact with hard
objects such as branches, stones etc. as the cutting tool will revolve when
starting.
The engine is to be switched off immediately in case of any engine problems.
Should the cutting tool hit stones or other hard objects, immediately switch off
the engine and inspect the cutting tool.
Inspect the cutting tool at short regular intervals for damage (detection of
hairline cracks by means of tapping-noise test).
Operate the Brush Cutter/String trimmer only with the shoulder strap
attached which is to be suitably adjusted before putting the Brush Cutter/
String trimmer into operation. It is essential to adjust the shoulder strap
according to the users size to prevent fatigue occurring during use. Never
hold the cutter with one hand during use.
During operation always hold the Brush Cutter/String trimmer with both
hands.
Always ensure a safe footing.
Operate the Brush Cutter/String trimmer in such a manner as to avoid
inhalation of the exhaust gases. Never run the engine in enclosed rooms
(risk of gas poisoning). Carbon monoxide is an odorless gas.
Switch off the engine when resting and when leaving the Brush Cutter/
String trimmer unattended, and place it in a safe location to prevent danger to
others or damage to the machine.
Never put the hot Brush Cutter/String trimmer onto dry grass or onto any
combustible materials.
The cutting tool has to be equipped with its appropriate guard.
Never run the cutter without this guard!
All protective installations and guards supplied with the machine must be
used during operation.
Never operate the engine with faulty exhaust muffler.
Shut off the engine during transport.
During transport over long distances the tool protection included with the
equipment must always be used.
Ensure safe position of the Brush Cutter/String trimmer during car transpor-
tation to avoid fuel leakage.
When transporting the Brush Cutter/String trimmer, ensure that the fuel tank
is completely empty.
When unloading the Brush Cutter/String trimmer from the truck, never drop
the Engine to the ground or this may severely damage the fuel tank.
Except in case of emergency, never drop or cast the Brush Cutter/String
trimmer to the ground or this may severely damage the Brush Cutter/String
trimmer.
Remember to lift the entire equipment from the ground when moving the
equipment. Dragging the fuel tank is highly dangerous and will cause
damage and leakage of fuel, possibly causing fire.
Refuelling
Shut off the engine during refuelling, keep away from open flames and do
not smoke.
Avoid skin contact with mineral oil products. Do not inhale fuel vapor.
Always wear protective gloves during refuelling. Change and clean
protective clothing at regular intervals.
Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the Brush Cutter/String trimmer immedi-
ately after fuel has been spilt.
Avoid any fuel contact with your clothing. Change your clothing instantly if
fuel has been spilt on it (to prevent clothing catching fire).
Inspect the fuel cap at regular intervals making sure that it can be securely
fastened and does not leak.
Carefully tighten the fuel tank cap. Change location to start the engine (at
least 3 meters away from the place of refuelling).
Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of
explosions).
Only transport and store fuel in approved containers. Make sure the fuel
stored is not accessible to children.
Resting
Transport
Refuelling
Maintenance
Tool Replacement
3
m
e
t
e
r
s
4
Method of operation
Only use the Brush cutter/String trimmer in good light and visibility. During the
winter season beware of slippery or wet areas, ice and snow (risk of
slipping). Always ensure a safe footing.
Never cut above waist height.
Never stand on a ladder and run the Brush cutter/String trimmer.
Never climb up into trees to perform cutting operation with the Brush cutter/
String trimmer.
Never work on unstable surfaces.
Remove sand, stones, nails etc. found within the working range.
Foreign particles may damage the cutting tool and can cause dangerous
kick-backs.
Before commencing cutting, the cutting tool must have reached full working
speed.
Kickback
When operating the brush cutter, uncontrolled kickback may occur.
This is particularly the case when attempting to cut within a blade segment
between 12 and 2 oclock.
Never apply the brush cutter within a segment between 12 and 2 oclock.
Never apply this segment of the brush cutter blade to solids, such as
bushes and trees, etc., having a diameter in excess of 3 cm or the brush
cutter will be deflected at great force with the risk of injuries.
Kickback prevention
To avoid kickbacks, observe the following:
Operation within a blade segment between 12 and 2 oclock presents
positive hazards, especially when using metal cutting tools.
Cutting operations within a blade segment between 11 and 12 oclock, and
between 2 and 5 oclock, must only be performed by trained and experi-
enced operators, and then only at their own risk.
Easy cutting with almost no kickback is possible within a blade segment
between 8 and 11 oclock.
Cutting Tools
Employ only the correct cutting tool for the job in hand.
RBC2500 with cutter blade (Star Blade (4 teeth), Eddy Blade (8 teeth)),
RBC2510 with Nylon cutting head.
For cutting thick materials, such as weed, high grass, bushes, shrubs,
underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work
by swinging the brush cutter evenly in half-circles from right to left (similar to
using a scythe).
Maintenance instructions
The condition of the cutter, in particular of the cutting tool of the protective
devices and also of the shoulder strap must be checked before commencing
work. Particular attention is to be paid to the cutting blades which must be
correctly sharpened.
Turn off the engine and remove spark plug connector when replacing or
sharpening cutting tools, and also when cleaning the cutter or cutting tool.
Caution:
Kickback
Diagrammatic
flgure
Diagrammatic
flgure
5
EU Conformity Declaration
The undersigned, Yasuhiko Kanzaki, as authorized by MAKITA INTERNATIONAL EUROPE LTD., Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, U.K., declare that the Makita Machines,
Type : RBC2500, RBC2510
manufactured by Robin conforms to the basic safety and health requirements of the applicable EU guidelines:
EU Machine guideline 98/37/EG
EU EMC guideline 89/336/EWG (modified by 91/263/EWG, 92/31/EWG and 93/68/EWG)
Noise Emission guideline 2000/14/EC
The most important standards applied to properly meet the requirements of the above EU guidelines were:
EN 11806, CISPR 12, EN50082-1, DIN VDE 0879 T1.
Technical Documentation: Fuji Robin Industries Ltd.
35 OHOKA, NUMAZU - CITY, SHIZUOKA - PREF, 410-8535 JAPAN
Hiroshi Hirooka
General Manager, Engineering Department
Guaranteed Sound Power :114 dB
Measured Sound Power : 110 dB
Milton Keynes, 01.02.03
For MAKITA INTER NATIONAL EUROPE LTD.
Yasuhiko Kanzaki
Managing Director
Never straighten or weld damaged cutting tools.
Operate the Brush cutter/String trimmer with as little noise and contamination
as possible. In particular check the correct setting of the carburetor.
Clean the Brush cutter/String trimmer at regular intervals and check that all
screws and nuts are well tightened.
Never service or store the Brush cutter/String trimmer in the vicinity of naked
flames.
Always store the Brush cutter/String trimmer in locked rooms and with an
emptied fuel tank.
Observe the relevant accident prevention instructions issued by the relevant
trade associations and by the insurance companies.
Do not perform any modifications on the Brush cutter/String trimmer as this will
endanger your safety.
The performance of maintenance or repair work by the user is limited to those
activities as described in the instruction manual. All other work is to be done
by an Authorized Service Agent. Use only genuine spare parts and
accessories released and supplied by MAKITA.
Use of non-approved accessories and tools means increased risk of
accidents.
MAKITA will not accept any liability for accidents or damage caused by the
use of non-approved cutting tools and fixing devices of cutting tools, or
accessories.
First Aid
In case of accident make sure that a first-aid box is available in the vicinity of
the cutting operations. Immediately replace any item taken from the first aid
box.
When asking for help, please give the following information:
Place of accident
What happened
Number of injured persons
Kind of injuries
Yo u r n a me
Packaging
The MAKITA Brush cutter/String trimmer will be delivered in two protective
cardboard boxes to prevent transport damage. Cardboard is a basic raw
material and is therefore consequently reusable or suitable for recycling
(waste paper recycling).
Loading...
+ 13 hidden pages