INSTRUCTION MANUAL
MANUEL D'INSTRUCTION
MANUAL DE INSTRUCCIONES
Cordless Cleaner
Aspirateur sans fil
Aspiradora Inalámbrica
LC01
010062
IMPORTANT: Read Before Using.
IMPORTANT: Lire avant usage.
IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions)
SPECIFICATIONS
Model |
LC01 |
Capacity |
600 mL |
Continuous use |
Approx. 12 min. |
Overall length |
966 mm (38-1/32") |
Net weight |
0.88 kg (1.94 lbs) |
Rated voltage |
D.C. 10.8 V / 12 V max |
Standard battery cartridges |
BL1014 |
•Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
•Specifications and battery cartridge may differ from country to country.
•Weight, with battery cartridge, according to EPTA-Procedure 01/2003
USA012-1
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING
To reduce the risk of fire, electric shock or injury:
1.Do not leave appliance when battery fitted. Remove battery from appliance when not in use and before servicing.
2.Do not expose to rain. Store indoors.
3.Do not allow to be used as a toy. Close attention is necessary when used by or near children.
4.Use only as described in this manual. Use only manufacturer's recommended attachments.
5.Do not use with damaged battery. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
6.Do not handle appliance with wet hands.
7.Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
8.Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
9.Turn off all controls before removing the battery cartridge.
10.Use extra care when cleaning on stairs.
11.Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
12.Use only the charger supplied by the manufacturer to recharge.
13.Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
14.Do not use without filters in place.
15.Do not charge the battery outdoors.
2
SAVE THESE INSTRUCTIONS.
This appliance is intended for household use.
USB062-2
6.Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
ENC007-5
ADDITIONAL |
IMPORTANT |
SAFETY RULES |
SAFETY |
1.Read this instruction manual and INSTRUCTIONS the charger instruction manual
carefully before use.
2.Do not pick up the following
|
materials: |
|
|
|
|
|
FOR BATTERY |
|
|||||||
|
− |
Hot |
materials such as lit |
|
|||||||||||
|
|
cigarettes |
or |
spark/metal dust |
CARTRIDGE |
|
|
||||||||
|
|
generated |
by |
grinding/cutting |
|
|
|||||||||
|
|
metal |
|
|
|
|
|
|
1. Before using battery cartridge, read |
||||||
|
− |
Flammable |
materials |
such |
as |
|
all |
instructions |
and |
cautionary |
|||||
|
|
gasoline, |
thinner, |
benzine, |
|
markings on (1) battery charger, (2) |
|||||||||
|
|
kerosene or paint |
|
|
|
|
battery, and (3) product using |
||||||||
|
− |
Explosive |
|
materials |
like |
|
battery. |
|
|
|
|
||||
|
|
nitroglycerin |
|
|
|
|
2. |
Do |
not |
disassemble |
battery |
||||
|
− |
Ignitible materials such as |
|
cartridge. |
|
|
|
|
|||||||
|
|
Aluminum, |
zinc, |
magnesium, |
3. If operating time has become |
||||||||||
|
|
titanium, |
phosphorus |
or |
|
excessively shorter, stop operating |
|||||||||
|
|
celluloid |
|
|
|
|
|
|
immediately. It may result in a risk |
||||||
|
− Wet dirt, water, oil or the like |
|
|
of overheating, possible burns and |
|||||||||||
|
− |
Hard |
pieces with sharp edges, |
|
even an explosion. |
|
|
|
|||||||
|
|
such as wood chips, metals, |
4. |
If electrolyte gets |
into your eyes, |
||||||||||
|
|
stones, glasses, nails, pins or |
|
rinse them out with clear water and |
|||||||||||
|
|
razors |
|
|
|
|
|
|
seek medical attention right away. It |
||||||
|
− Powder to clot such as cement |
|
may result in loss of your eyesight. |
||||||||||||
|
|
or tonor |
|
|
|
|
|
5. Do not short the battery cartridge: |
|||||||
|
− |
Conductive dust such as metal |
|
(1) |
Do not touch the terminals with |
||||||||||
|
|
or carbon |
|
|
|
|
|
|
|
any conductive material. |
|||||
|
− Fine particle like concrete dust |
|
(2) Avoid storing |
battery |
cartridge |
||||||||||
|
Such action may cause fire, injury |
|
|
in a container with other metal |
|||||||||||
|
and/or property damage. |
|
|
|
|
objects such as nails, coins, etc. |
|||||||||
3. |
Stop operation immediately if |
you |
|
(3) |
Do not expose battery cartridge |
||||||||||
|
notice anything abnormal. |
|
|
|
|
to water or rain. |
|
|
|||||||
4. |
If you drop or strike |
the |
cleaner, |
|
|
A battery short can cause a large |
|||||||||
|
check it carefully for cracks or |
|
|
current |
flow, |
overheating, |
|||||||||
|
damage before operation. |
|
|
|
|
possible burns and even a |
|||||||||
5. |
Do |
not |
bring |
close to stoves or |
|
|
breakdown. |
|
|
|
|||||
|
other heat sources. |
|
|
|
|
|
|
|
|
|
|
3
6.Do not store the tool and battery
cartridge in locations where the FUNCTIONAL temperature may reach or exceed
7.Do not incinerate the battery DESCRIPTION
cartridge even if it is severely |
CAUTION: |
damaged or is completely worn out. |
|
The battery cartridge can explode in |
• Always be sure that the tool is switched |
a fire. |
off and the battery cartridge is removed |
8. Be careful not to drop or strike |
before adjusting or checking function on |
battery. |
the tool. |
9.Do not use a damaged battery.
SAVE THESE |
|
Installing or removing battery |
||||
|
cartridge |
|
||||
INSTRUCTIONS. |
|
|||||
|
1 |
1. Battery cartridge |
||||
|
|
|
|
|
||
|
|
|
|
|
2. Button |
|
Tips for maintaining maximum |
|
|
|
|
||
battery life |
|
|
|
|
|
|
1. Charge the battery cartridge before |
2 |
|
|
|||
completely discharged. |
|
|
|
|
||
Always stop tool operation and |
010014 |
Always switch off |
the tool before |
|||
charge the battery cartridge when |
• |
|||||
you notice less tool power. |
|
|
insertion or removal of the battery |
|||
2. Never recharge a fully charged |
|
cartridge. |
|
|||
battery cartridge. |
|
|
• |
To remove the |
battery cartridge, |
|
Overcharging shortens the battery |
|
withdraw it from the tool while pressing |
||||
service life. |
|
|
|
|
the buttons on both sides of the |
|
3. Charge the |
battery |
cartridge with |
|
cartridge. |
|
|
room temperature at 10 C - |
40 C |
• To insert the battery cartridge, hold it so |
||||
(50 F - 104 F). Let a hot battery |
|
that the battery cartridge front shape fits |
||||
cartridge |
cool |
down |
before |
|
to that of the battery installment opening |
|
charging it. |
|
|
|
|
and slip it into place. Always insert it all |
the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.
4
Switch action
1. Switch trigger
1
010063
CAUTION:
•Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Release the switch trigger to stop.
ASSEMBLY
CAUTION:
•Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
Disposing of Dust
CAUTION:
•Empty the cleaner before it becomes too full, or the suction force weakens.
•Be sure to empty out the dust inside the cleaner itself. Failure to do so may cause the filter to be clogged or the motor to be damaged.
1. Capsule
2. Suction inlet
1
2
010022
In order to drop dust sticking on the filter in the capsule, tap the capsule 4 or 5 times with your hand.
1. Capsule
2. Suction inlet
1
2
010023
Now point suction inlet downwards, turn capsule in direction of arrow in diagram, and disconnect capsule slowly and straight.
NOTE:
• Dust may spill out when capsule is opened, so be sure to set a garbage bag beneath capsule.
1. Prefilter
2. Capsule
1
2
010024
Remove accumulated dust from inside of capsule and off of prefilter.
1. Prefilter
2. Securing lip
1
2
010025
Twist prefilter in direction of arrow to unfasten securing lip from cleaner unit and then pull off prefilter.
|
1. |
Filter |
|
2. |
Prefilter |
2 |
1 |
|
010026 |
|
|
5
Clean out fine dust from prefilter. Next, remove filter, and lightly tap to dislodge dust.
Reassembly
1. Filter
1
010070
Put on filter until it is fully in position on the cleaner unit.
NOTE:
• Make sure filter is put on straight |
without being peeled back. If filter is put |
on incorrectly as shown in diagram, |
dust will get into motor housing, and |
cause motor failure. |
1. Filter |
1 |
010028 |
Connect prefilter. At this time, make sure to twist prefilter so that securing lip is firmly locked into cleaner unit.
|
1. Prefilter |
2 |
2. Securing lip |
|
|
|
1 |
010029 |
|
010030
Connect capsule. Align projection on capsule with projection on handle and then firmly twist capsule in direction of arrow until it is secured.
010031 |
1 |
2 |
3 |
|
010032 |
|
NOTE: |
|
1.Capsule
2.Handle
3.Projection
•Always remove dust ahead of time, as suction power will be reduced if there is too much dust in cleaner.
•Always be sure to check that both filter and prefilter are loaded correctly prior to using cleaner. If they are not loaded correctly, dust will get into the motor housing, and cause motor failure.
If the following examples occur, filter and prefilter are not loaded correctly. Reload them correctly to rectify problem.
6
Problem Examples
Example 1: Only prefilter has been loaded (no filter)
1. Prefilter
1
010033
Example 2: Only filter has been loaded (no prefilter)
1. Filter
1
010034
Example 3: Filter has been loaded in a peeled back state
1. Filter
1
010028
Example 4: Prefilter's securing lip is not firmly locked into groove of cleaner housing
|
3 |
1. Groove of |
|
1 |
|
cleaner housing |
|
|
2. |
Prefilter |
|
|
|
||
|
|
3. |
Securing lip |
2 |
|
|
|
010036 |
|
|
|
OPERATION
CAUTION:
•To connect attachments, such as nozzle, twist-insert attachment in direction of arrow to ensure secure connection during use. To disconnect attachment, twist-extract also in direction of arrow.
If attachment is twisted in the opposite direction, when being connected or disconnected, capsule may become loose.
1. Capsule
1
010064
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture, etc. Nozzle slips on easily.
1. Nozzle
1
010065
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the cleaner itself. This arrangement is convenient for cleaning a floor while standing erect.
7
1. Cleaner body
2. Extension wand
3. Nozzle
1 |
2 |
3 |
010067
Corner nozzle
Fit on the corner nozzle for cleaning corners and crevices of a car or furniture.
1. Corner nozzle
2. Cleaner body
1 |
2 |
010068
Corner nozzle +Extension wand (Straight pipe)
In tight quarters where the cleaner itself cannot squeeze in, or in high places hard to reach, use this arrangement.
1. Corner nozzle
2. Extension wand
3. Cleaner body
1 |
2 |
3 |
010069
Cleaning without nozzle
You can pick up powder and dust without nozzle.
010066
MAINTENANCE
CAUTION:
•Always be sure that the tool is switched off before attempting to perform inspection or maintenance.
After use
When storing the cleaner, hang it from a nail using the convenient hanger in back.
010071
Cleaning
010072
From time to time wipe off the outside (cleaner body) of the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/dust pack mounting area and the dust stopper.
CAUTION:
•Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
8
|
Wash the filter in soapy water when it is |
|
|
clogged with dust and the cleaner power |
|
|
becomes small. Dry it out thoroughly before |
|
|
use. An insufficiently dried filter may cause |
|
|
poor suction and shorten the service life of |
|
|
the motor. |
|
010009 |
|
|
|
Things to Check Before Asking for |
|
|
Repairs |
|
Symptom |
Area to be investigated |
Fixing method |
|
Is capsule full of dust? |
Empty dust from capsule. |
Weak suction power |
Is filter clogged? |
Dust down or wash filter. |
|
Is battery exhausted? |
Recharge battery. |
Not working |
Is battery exhausted? |
Recharge battery. |
010051
NOTE:
•Do not attempt to repair cleaner by yourself.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
•
•
•
•
•
•
Corner nozzle Round brush Flexible hose Filter
Prefilter
Various type of Makita genuine batteries and chargers
ACCESSORIES
CAUTION:
•These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
•Extension wand (Straight pipe)
•Nozzle
•Nozzle for carpet
•Shelf brush
9
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wear and tear:
the tool has been abused, misused or improperly maintained:
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
EN0006-1
10