Lowrance electronic LMS 335C DF, LMS 330C User Manual

4.5 (2)
Lowrance electronic LMS 335C DF, LMS 330C User Manual

Pub. 988-0156-011

www.lowrance.com

LMS 330C &

LMS 335C DF

Fish-finding Sonar & Mapping GPS

Installation and Operation

Instructions

Copyright © 2004 Lowrance Electronics, Inc.

All rights reserved.

Lowrance® is a registered trademark of Lowrance Electronics, Inc. MapCreate is a trademark of Lowrance Electronics, Inc.

Navionics is a registered trademark of Navionics, Inc.

Points of Interest Data in this unit are by infoUSA, copyright 2001-2004, All Rights Reserved. infoUSA is a trademark of infoUSA, Inc.

eXitSource Database, copyright 2001-2004 Zenrin Co. Ltd. Exit Authority and eXitSource are trademarks of Zenrin Co. Ltd.

Lowrance Electronics may find it necessary to change or end our policies, regulations and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. On the cover: LMS-335C DF shown.

For free owner's manuals and other information, visit our web site:

www.lowrance.com

Lowrance Electronics Inc.

12000 E. Skelly Dr.

Tulsa, OK USA 74128-2486

Printed in USA.

Table of Contents

 

Sec. 1: Read Me First! ...............................................................

1

Capabilities and Specifications: LMS-330C and LMS-335C DF.. 3

How Lowrance Sonar Works ........................................................

5

How Lowrance GPS Works ..........................................................

6

Introduction to GPS and WAAS...................................................

8

Free Training Aids Available .....................................................

10

Sonar Viewer...........................................................................

10

Unit Emulator.........................................................................

11

How to Use this Manual: Typographical Conventions..............

12

Sec. 2: Installation & Accessories ........................................

15

Preparations................................................................................

15

Transducer Installation..............................................................

15

Selecting a Transducer Location............................................

16

Shoot-Thru-Hull vs. Transom Mounting ...............................

18

Transom Transducer Assembly and Mounting .....................

19

Trolling Motor Bracket Installation.......................................

25

Transducer Orientation and Fish Arches ..............................

25

Shoot-Thru-Hull Preparation and Installation .....................

26

Speed/Temperature Sensors.......................................................

30

Optional Temperature Sensor................................................

30

Optional Speed Sensor Installation .......................................

30

GPS Antenna/Receiver Module ..................................................

32

GPS Module Installation ........................................................

33

Connecting Directly to the Unit .............................................

35

Connecting to a NMEA 2000 Network...................................

35

Power Connections .................................................................

36

Powering a NMEA 2000 Buss (NMEA 2000 Power Cable).......

37

Powering your Unit (Power Supply Cable)................................

37

NMEA 2000 Cable Connections .................................................

39

NMEA 0183 Cable Connections (Data Cable) ...........................

40

Mounting the Unit: Bracket, In-Dash or Portable ....................

41

MMC or SD Card Memory Card Installation............................

44

Face Cover...................................................................................

45

Other Accessories........................................................................

46

Switch Boxes ...........................................................................

46

Sec. 3: Basic Sonar Operation...............................................

47

Keyboard .....................................................................................

47

Power/Lights (Turn Unit On and Off) .......................................

48

Main Menu ..................................................................................

48

Pages ...........................................................................................

50

Satellite Status Page ..............................................................

50

Navigation Page......................................................................

51

i

 

Map Page.................................................................................

51

Sonar Page ..............................................................................

52

Basic Sonar Quick Reference ...............................................

55

Sonar Operations ........................................................................

56

Fish Symbols vs. Full Sonar Chart ........................................

58

Sec. 4: Sonar Options & Other Features ............................

59

ASP (Advanced Signal Processing) .........................................

59

Alarms .........................................................................................

60

Depth Alarms ..........................................................................

60

Zone Alarm..............................................................................

61

Fish Alarm...............................................................................

62

Calibrate Speed...........................................................................

63

Chart Speed.................................................................................

64

Colorline ...................................................................................

65

Depth Cursor...............................................................................

66

Depth Range - Automatic ...........................................................

67

Depth Range - Manual................................................................

67

To Turn Auto Depth Range on Again: ...................................

67

Depth Range - Upper and Lower Limits ...................................

68

FasTrack ..................................................................................

69

Fish I.D. (Fish Symbols & Depths) .........................................

70

FishTrack .................................................................................

71

Frequency (Change Transducer Frequency) .............................

71

HyperScroll ..............................................................................

72

Iceview Chart Mode (Signal Interpretation) .............................

73

Signal Band Movement...........................................................

73

Signal Band Color ...................................................................

73

Signal Band Thickness ...........................................................

74

Log Sonar Chart Data ................................................................

74

Noise Rejection............................................................................

75

Overlay Data...............................................................................

75

Ping Speed & HyperScroll .......................................................

77

Reset Options ..............................................................................

79

Reset Water Distance .................................................................

79

Set Keel Offset ............................................................................

80

Sensitivity & Auto Sensitivity....................................................

81

Turn Auto Sensitivity Back on:..............................................

82

Sonar Chart Mode.......................................................................

82

Sonar Page & Sonar Chart Display Options .............................

83

Full Sonar Chart .....................................................................

83

Split Zoom Sonar Chart..........................................................

84

Digital Data.............................................................................

84

Customizing the Digital Data Screen ................................

85

ii

 

FlashGraf ............................................................................

86

Flasher.....................................................................................

87

Map with Sonar Split Screen .................................................

87

Sonar Simulator..........................................................................

88

Stop Chart ...................................................................................

90

Surface Clarity............................................................................

91

Upper and Lower Limits ............................................................

92

Zoom & Zoom Bar .......................................................................

92

Zoom Pan.....................................................................................

92

Sec. 5: Sonar Troubleshooting..............................................

95

Sec. 6: Basic GPS Operations................................................

99

Keyboard .....................................................................................

99

Power/Lights (Turn Unit On and Off) .....................................

100

Main Menu ................................................................................

100

Pages .........................................................................................

102

Sonar Page ............................................................................

102

Satellite Status Page ............................................................

102

Navigation Page....................................................................

104

Map Page...............................................................................

106

Background Map vs. Mapcreate Map Content ................

108

Resize Window Command ................................................

110

Basic GPS Quick Reference ................................................

112

Find your Current Position ......................................................

113

Moving around the Map: Zoom & Cursor Arrow Keys............

113

Selecting any Map Item with the Cursor ................................

114

Searching...................................................................................

114

Set a Waypoint..........................................................................

117

Create Waypoint at Current Position ..................................

117

Create Waypoint on Map......................................................

118

Create Waypoint by Entering a Position .............................

118

Navigate to a Waypoint ............................................................

119

Set Man Overboard (MOB) Waypoint......................................

120

Navigate Back to MOB Waypoint ............................................

120

Navigate to Cursor Position on Map........................................

121

Navigate to a Point of Interest.................................................

122

Creating and Saving a Trail.....................................................

122

Displaying a Saved Trail ..........................................................

124

Navigating Trails......................................................................

125

Visual Trailing ......................................................................

125

Navigate a Trail (Forward)...................................................

125

Navigate a Back Trail (Backtrack, or Reverse)...................

128

Transfer Custom Maps and GPS Data Files ...........................

128

Cancel Navigation.....................................................................

130

iii

 

Sec. 7: Advanced GPS Operations .....................................

131

Find Distance from Current Position to Another Location ....

131

Find Distance from Point to Point ...........................................

131

Icons...........................................................................................

132

Create Icon on Map...............................................................

132

Create Icon at Current Position ...........................................

132

Delete an Icon .......................................................................

133

Navigate to an Icon...............................................................

133

Routes........................................................................................

134

Create and Save a Route ......................................................

134

PC-Created Routes............................................................

134

Routes Created in the Unit...............................................

134

Delete a Route.......................................................................

137

Edit a Route Name................................................................

137

Edit Route Waypoints...........................................................

137

Navigate a Route...................................................................

138

Navigate a Route in Reverse ................................................

139

Trails .........................................................................................

140

Delete a Trail ........................................................................

140

Edit a Trail Name .................................................................

140

Edit a Trail Color ..................................................................

141

Edit a Trail Pattern ..............................................................

141

Utilities......................................................................................

142

Alarm Clock...........................................................................

142

Sun/Moon Rise & Set Calculator..........................................

142

Trip Calculator......................................................................

142

Trip Down Timer...................................................................

142

Trip Up Timer .......................................................................

142

Waypoints..................................................................................

142

Delete a Waypoint.................................................................

142

Edit a Waypoint (Name, Symbol and Position) ...................

142

Selecting a Waypoint ............................................................

143

Set a Waypoint by Average Position ....................................

143

Set a Waypoint by Projecting a Position..............................

144

Sec. 8: System & GPS Setup Options.................................

145

Alarms .......................................................................................

145

Check MMC Files and Storage Space......................................

146

Communications Port Configuration .......................................

146

Configure NMEA ......................................................................

147

Coordinate System Selection....................................................

148

Setup Loran TD.....................................................................

149

Map Fix .....................................................................................

150

Customize Page Displays .........................................................

151

iv

 

Customize Satellite Status Page..........................................

151

Customize Navigation Page .................................................

151

Customize Map Page ............................................................

151

GPS Simulator ..........................................................................

151

Simulating Trail or Route Navigation .................................

152

Hide GPS Features ...................................................................

153

Initialize GPS............................................................................

153

Map Auto Zoom.........................................................................

153

Map Data...................................................................................

154

Show Map Data.....................................................................

154

Pop-Up Map Information......................................................

154

Map Boundaries ....................................................................

155

Fill Water with White...........................................................

155

Map Overlays (Range Rings; Lat/Long Grid) ......................

155

Map Datum Selection ...............................................................

155

Map Detail Category Selection.................................................

156

Map Orientation .......................................................................

157

Navionics Charts.....................................................................

158

Display a Navionics Chart:...................................................

158

Port Information ...................................................................

159

Tidal Current Information ...................................................

160

Tide Information ...................................................................

162

Pop-Up Help..............................................................................

163

Position Pinning........................................................................

164

Reset Options ............................................................................

164

Require WAAS ..........................................................................

165

Screen Contrast and Brightness ..............................................

165

Set Language ............................................................................

166

Set Local Time ..........................................................................

167

Show WAAS Alarm...................................................................

167

Software Version Information..................................................

168

Sounds and Alarm Sound Styles..............................................

168

Track Smoothing.......................................................................

169

Trail Options .............................................................................

170

Delete All Trails ....................................................................

170

Update Trail Option..............................................................

170

Update Trail Criteria (Auto, Time, Distance)..................

170

Trail Update Rate (Time, Distance).................................

171

Delete Trail ...........................................................................

171

New Trail...............................................................................

172

Trail Visible/Invisible and Other Trail Options ..................

172

Transparency ............................................................................

172

Units of Measure.......................................................................

173

v

 

Sec. 9: Searching....................................................................

175

Find Addresses..........................................................................

176

Find any Item Selected by Map Cursor ...................................

179

Find Interstate Highway Exits ................................................

179

Find Map Places or Points of Interest (POI) ...........................

182

Find Streets or Intersections....................................................

184

Find Waypoints.........................................................................

188

Sec. 10: Supplemental Material..........................................

191

Index.........................................................................................

197

WARNING!

A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION.

CAUTION

When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only take advantage of all available navigation tools when traveling to a waypoint, but will also visually check to make sure a clear, safe path to the waypoint is always available.

WARNING!

When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for operating the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all pertinent driving, boating or flying conditions at all times. An accident or collision resulting in damage to property, personal injury or death could occur if the operator of a GPS-equipped vehicle fails to pay full attention to travel conditions and vehicle operation while the vehicle is in motion.

vi

Section 1: Read Me First!

How this manual can get you out on the road, fast!

Welcome to the exciting world of digital sonar and GPS! We know you're anxious to begin navigating and finding fish, but we have a favor to ask. Before you grab the unit and begin installing it, please give us a moment or two to explain how our manual can help you get the best performance from your compact, color display, combination fish finder and mapping GPS receiver.

First, we want to thank you for buying a Lowrance sonar/GPS unit. Whether you're a first time user or a professional fisherman, you'll discover that your unit is easy to use, yet capable of handling demanding navigation and sonar tasks. When you team your unit with our custom mapping software MapCreate 6, you have an incredible combination. You won't find another combination GPS and sonar unit with this much power and this many features for this price!

Our goal for this book is to get you on the water fast, with a minimum of fuss. Like you, we'd rather spend more time boating or fishing and less time reading the manual!

So, we designed our book so that you don't have to read the whole thing from front to back for the information you want. At the start (or end) of each segment, we'll tell you what content is coming up next. If it's a concept you're already familiar with, we'll show you how and where to skip ahead for the next important topic. We've also made it easy to look up any tips you may need from time to time. Here's how:

The manual is organized into 10 sections. This first section is an introduction to the LMS-330C or LMS-335C DF, sonar and GPS. It tells you the basics you need to know before you can make the unit look around and tell you where you are, or look below the surface to find some fish.

Section 2 will help you install your unit, the transducer and the GPS antenna module. We'll show you how to get the MultiMedia Card (MMC) correctly installed inside the unit. We'll also tell you about some of the available accessories.

Section 3 covers Basic Sonar Operation. It will show you how easy it is to run your unit, right out of the box. This section features a one-page Sonar Quick Reference. (If you've already jumped ahead and figured out how to install the unit yourself, and you just can't wait any longer, turn to the Quick Reference on page 55 and head for the water with your unit!)

1

After you've gained some experience with your sonar, you'll want to check out Section 4, which discusses more advanced Sonar Options and Other Features.

When you come to a sonar menu command on the unit's screen, you can look it up in the manual by skimming over the table of contents, just flipping through Section 3 or scanning through the sonar options in Section 4.

If you're having difficulty with your sonar, you can find an answer to the most common problems in Section 5, Sonar Troubleshooting.

The manual switches from sonar to navigation in Section 6, which introduces you to Basic GPS Operations. This section features a onepage GPS Quick Reference on page 112.

Section 6 contains short, easy-to-scan GPS lessons that follow one another in chronological order. They're all you'll need to know to find your way on the water quickly.

After you've learned the basics (or if you already have some GPS experience), you may want to try out some of the unit's many advanced navigation features. That brings us to Section 7, Advanced GPS Operations. This section contains the rest of the unit's GPS command functions, organized in alphabetical order.

When you come to a GPS menu command on the screen, you can look it up in the manual by skimming over the table of contents, just flipping through Section 6 or scanning through the command portion of Section 7.

This unit is ready to use right out of the box, but you can fine tune and customize it's operation with dozens of options. Since sonar is the unit's key feature, we put the main sonar options in Section 4. Some options, such as screen brightness settings, affect both sonar and GPS operations. We describe how to use those common options along with GPS options in Section 8, System Setup and GPS Setup Options. Section 8 is organized in alphabetical order.

In Section 9, we go into more detail on one of the unit's most remarkable GPS capabilities — Searching. We'll introduce a search example in the Basic GPS Operation section, but there are so many map items you can search for, we had to give this function it's own section in the manual! For example, did you know this unit can look up business phone numbers, functioning as a virtual Yellow Pages? We’ll show you how in Section 9.

Finally, in Section 10, we offer Supplemental Material, including a list of the GPS datums used, warranties and customer service information.

2

Now, if you're into the fine details, glance over the next segment on specifications to see just how much sonar and GPS power your unit contains. It's important to us (and our power users), but, if you don't care how many watts of power the unit has, or how many waypoints it can store, skip ahead to important information on how the sonar works, on page 5. (Background on GPS begins on page 6.)

Capabilities and Specifications: LMS-330C and LMS-335C DF

 

General

Display:............................

1/4 VGA color, transflective TFT display; 5.0"

 

(12.7 cm) diagonal viewing area.

Resolution:......................

320 pixels (vert.) x 240 pixel (horiz.) resolu-

 

tion; 153,600 total pixels

Backlighting:...................

Color backlit screen and keypad for night use.

Input power:...................

10 to 15 volts DC.

Current drain: ...............

Sonar only: 500 ma lights off; 600 ma lights

 

on. With GPS and lights on: 700 ma.

Case size:.........................

5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6

 

cm); sealed and waterproof; suitable for

 

saltwater use.

MMC slots:...........................

One with waterproof door (SD card compatible).

Recording:........................

GPS uses MMC & SD cards for recording trip

 

details and displaying charts or custom maps.

 

Sonar uses them to record and save sonar

 

chart logs.

Back-up memory: ..........

Built-in memory stores sonar records and

 

GPS data for decades. User settings are

 

stored when unit is turned off.

Languages:......................

10; menu languages selectable by user.

 

Sonar

Frequency:......................

LMS-335C DF: 50/200 kHz.

 

LMS-330C: 200 kHz.

Transducers:....................

A dual-frequency Skimmer transducer with

 

built-in temperature sensor is packed with the

 

LMS-335C DF. It has 35°/12° cone angles. A

 

single-frequency Skimmer transducer with

 

built-in temperature sensor is packed with the

 

LMS-330C. It has a 20° cone angle. Transduc-

 

ers operate at speeds up to 70 mph (61 kts).

3

Maximum

 

transmitter power: .......

LMS-335C DF:

 

4,000 watts peak-to-peak/500 watts RMS.

 

LMS-330C:

 

2,400 watts peak-to-peak/300 watts RMS.

Sonar sounding

 

depth capability: ...........

LMS-335C DF: 2,500 feet/762 meters.

 

LMS-330C: 900 feet/275 meters.

 

(Actual capability depends on transducer

 

configuration and installation, bottom com-

 

position and water conditions. All sonar

 

units typically read deeper in fresh water

 

than in salt water.)

Depth display:................

Continuous display.

Graph recording:...........

More than 256 MB on one MMC (or SD) card

Audible alarms: .............

Deep/shallow/fish/zone.

Automatic ranging:.......

Yes, with instant screen updates.

Auto bottom track:........

Yes

Zoom bottom track: ......

Yes.

Split-screen zoom:.........

Yes.

Surface water temp: .....

Yes, built into transducer.

Speed/distance log: .......

Yes, with optional speed sensor (sensor in-

 

cluded with LMS-335C DF.)

 

GPS

Receiver/antenna:............

External; LGC-2000 12 parallel channel

 

NMEA 2000-ready GPS/WAAS re-

 

ceiver/antenna.

Background map:..........

Built-in custom, detailed Lowrance map.

 

Contains: enhanced detail of continental U.S.

 

and Hawaii. Includes more than 60,000 nav

 

aids and 10,000 wrecks/obstructions in

 

coastal and Great Lakes waters. Metro ar-

 

eas, selected major streets/highways and in-

 

terstate exit services details included.

Custom mapping: ..........

MapCreate 6 software optional; optional

 

LEI FreedomMaps offer the same high-

 

detail without the work of MapCreate; Navi-

 

onics charts on MMC cards optional.

4

Mapping memory:............

More than 256 MB on one MMC (or SD) card.

Position updates: ..........

Every second.

Position points: .............

1,000 waypoints; 1,000 event marker icons.

Audible alarms: .............

Arrival/off-course/anchor.

Graphic symbols for

 

waypoints or event

 

marker icons: .................

42.

Routes:.............................

100; up to 100 waypoints per route.

Plot Trails:......................

10 savable; up to 9,999 points per trail.

Zoom range:....................

40 ranges; 0.02 to 4,000 miles.

NOTE:

The above memory capacities refer only to the unit's on-board memory. The amount of GPS or sonar data you can record and save for recall later is only limited by the number and capacity of MMC cards you have.

NOTICE!

The storage and operation temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius). Extended storage or operation in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty. For more information, contact the factory's Customer Service Department; phone numbers are listed on the last page.

How Lowrance Sonar Works

Sonar has been around since the 1940s, so if you already know how it works, skip down to read about the relatively new technology of GPS. But, if you've never owned a sonar fish finder, this segment will tell you the under water basics.

Sonar is an abbreviation for SOund NAvigation and Ranging, a technology developed during World War II for tracking enemy submarines. (Lowrance developed the world's first transistorized sportfishing sonar in 1957.) A sonar consists of a transmitter, transducer, receiver and display. In simple terms, here's how it finds the bottom, or the fish:

The transmitter emits an electrical impulse, which the transducer converts into a sound wave and sends into the water. (The sound frequency can't be heard by humans or fish.) The sound wave strikes an object (fish, structure, bottom) and bounces back to the transducer, which converts the sound back into an electrical signal.

5

The receiver amplifies this return signal, or echo, and sends it to the display, where an image of the object appears on the scrolling sonar chart. The sonar's microprocessor calculates the time lapse between the transmitted signal and echo return to determine the distance to the object. The whole process repeats itself several times each second.

Your unit can record a log of the sonar signals that scroll across the screen and save them to the MMC memory card. (These recordings are also called sonar charts or sonar graphs.) You can replay this sonar log in the unit using the Sonar Simulator function, or play it back on a personal computer using our free Sonar Viewer or product emulator. The viewer and emulator are available for download from the Lowrance web site, www.lowrance.com.

You can save several different sonar log files, erase 'em and record new ones, over and over again. The size of your sonar recordings is only limited by the free space available on your MMC.

How Lowrance GPS Works

You'll navigate faster and easier if you understand how the unit scans the sky to tell you where you are on the earth — and, where you're going. (But if you already have a working understanding of GPS receivers and the GPS navigation system, skip on ahead to Section 2, Installation & Accessories on page 15. If you're new to GPS, read on, and you can later impress your friends with your new-found knowledge.)

First, think of your unit as a small but powerful computer. (But don't worry — we made the units in this series easy to use, so you don't need to be a computer expert to find your way!) The unit includes a keypad and a screen with menus so you can tell it what to do. The screen also lets the unit show your location on a moving map, as well as point the way to your destination.

This gimbal-mounted unit uses an external antenna/receiver module, which makes the whole system work something like your car radio. But instead of your favorite dance tunes, this receiver tunes in to a couple of dozen GPS satellites circling the earth. (It will also listen in to the WAAS satellites in orbit, but more about that in the upcoming segment introducing you to GPS and WAAS.)

Your unit listens to signals from as many satellites as it can "see" above the horizon, eliminates the weakest signals, then computes its location in relation to those satellites. Once it figures its latitude and longitude, it plots that position on the moving map shown on the screen. The whole process takes place several times a second!

6

The performance doesn't stop there. Stored in the permanent memory of each GPS unit is a basic background map of the entire world. We lock it in here at the factory — you can't change or erase this map.

The background map is suitable for many navigation chores, but for maximum accuracy and much more detail, you need our optional mapmaking software, MapCreate 6. Some unit features — such as searching for businesses and addresses — won't work without a custom MapCreate map. There is so much detail in our background map (and even more in MapCreate) that we'll describe their contents and differences in Section 6, Basic GPS Operations, on page 99.

Another portion of the unit's onboard memory is devoted to recording GPS navigation information, which includes waypoints, event marker icons, trails and routes. This lets you look back the way you came. Think of this data storage like the hard drive memory in a computer or a tape in a cassette tape recorder. You can save several different GPS data files, erase 'em and record new ones, over and over again. Like any computer file, these GPS Data Files (file format *.usr) can be shared between other Lowrance GPS or sonar/GPS units, or even personal computers.

This unit has one more thing in common with a personal computer. Just as computers have a floppy disk drive for storing and exchanging files, the unit has a slot for an MMC (MultiMedia Card) or SD (Secure Digital card) flash memory card. These solid-state memory devices are about the size of a postage stamp, but can hold data ranging from 8 MB to more than 256 MB in size. (Compare that to a floppy disk's 1.44 MB capacity!) The unit uses all that MMC space for two key GPS purposes. (The MMC is also used to record sonar logs.)

First, you can backup your onboard GPS Data Files by copying them to the MMC. Since the MMC is removable (like a floppy disk or a cassette tape), you can store these GPS Data Files on a personal computer equipped with an MMC card reader. (Or store them on a pocketful of MMCs, if you don't have a computer.) Our MapCreate mapping software can save, edit or create its own GPS Data Files, which can be copied to the MMC and then loaded from the MMC into the unit's memory. (NOTE: No matter where they come from, GPS Data Files must be loaded from the MMC into memory before the unit can use them.)

The other key GPS use for MMCs is storage of special high-detail, custom maps, which you can produce on your computer with our MapCreate software. These MapCreate custom maps contain much greater de-

7

tail than the basic background map. These Custom Map Files (file format *.lcm) can also be shared between other Lowrance GPS or sonar/GPS units and personal computers. (For example, the exact same MMC, custom map files and GPS data files can be used interchangeably between your gimbal-mounted LMS-335C DF and the hand-held iFINDER GPS receiver.)

You make your own Custom Map Files with our MapCreate software, but you don't have to. We also sell ready-to-use FreedomMaps . These custom maps are pre-loaded on MMCs. (No computer work required!).

The unit automatically reads Custom Map Files directly from the MMC or SD card. To use a custom map, all you need to do is slide an MMC containing a map into the unit.

Introduction to GPS and WAAS

Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 15, so you can mount your unit and plug in the power. Or you might want to see how our text formatting makes the manual tutorials easy to skim. If that's the case, move on to "How to Use This Manual" on page 12. But, if you want to understand the current state of satellite navigation, look over this segment describing how GPS and its new companion WAAS work together to get you where you're going.

The Global Positioning System (GPS) was launched July 17, 1995 by the United States Department of Defense. It was designed as a 24- hour-a-day, 365-days-a-year, all weather global navigation system for the armed forces of the U.S. and its allies. Civilian use was also available at first, but it was less accurate because the military scrambled the signal somewhat, using a process called Selective Availability (SA.)

GPS proved so useful for civilian navigation that the federal government discontinued SA on May 2, 2000, after the military developed other methods to deny GPS service to enemy forces. Reliable accuracy for civilian users jumped from 100 meters (330 feet) under SA to the present level of 10 to 20 meters (about 30 to 60 feet.)

Twenty-four satellites orbit 10,900 nautical miles above the Earth, passing overhead twice daily. A series of ground stations (with precisely surveyed locations) controls the satellites and monitors their exact locations in the sky. Each satellite broadcasts a low-power signal that identifies the satellite and its position above the earth. Three of these satellites are spares, unused until needed. The rest virtually guarantee that at least four satellites are in view nearly anywhere on Earth at all times.

8

A minimum of three satellites are required to determine a 2D fix.

The system requires signal reception from three satellites in order to determine a position. This is called a 2D fix. It takes four satellites to determine both position and elevation (your height above sea level — also called altitude.) This is called a 3D fix.

Remember, the unit must have a clear view of the satellites in order to receive their signals. Unlike radio or television signals, GPS works at very high frequencies. These signals can be easily blocked by trees, buildings, an automobile roof, even your body.

Like most GPS receivers, this unit doesn’t have a compass or any other navigation aid built inside. It relies solely on the signals from the satellites to calculate a position. Speed, direction of travel, and distance are all calculated from position information. Therefore, in order for the unit to determine direction of travel, you must be moving and the faster, the better. This is not to say that it won’t work at walking or trolling speeds — it will. There will simply be more "wandering" of the data shown on the display.

GPS alone is plenty accurate for route navigation, but the U.S. Federal Aviation Administration has special aircraft navigation needs that go beyond basic GPS. So, the FAA has developed a program to boost GPS performance with its Wide Area Augmentation System, or WAAS. The FAA commissioned the system on July 11, 2003.

WAAS is designed to increase GPS accuracy to within 7.6 meters vertically and horizontally, but it consistently delivers accuracies within 1-2 meters horizontal and 2-3 meters vertical, according to the FAA. It does this by broadcasting correction signals on GPS frequencies. Your unit automatically receives both GPS and WAAS signals.

9

However, there are some fringe areas of the U.S., including parts of Alaska, that do not yet receive robust WAAS coverage. Continued WAAS development is planned to extend WAAS coverage in the years to come.

WAAS boosts the accuracy of land GPS navigation, but the system is designed for aircraft. The satellites are in a fixed orbit around the Equator, so they appear very low in the sky to someone on the ground in North America. Aircraft and vessels on open water can get consistently good WAAS reception, but terrain, foliage or even large man-made structures can sometimes block the WAAS signal from ground receivers.

You'll find that using your GPS receiver is both easy and amazingly accurate. It’s easily the most accurate method of electronic navigation available to the general public today. Remember, however, that this receiver is only a tool. Always have another method of navigation available, such as a map or chart and a compass.

Also remember that this unit will always show navigation information in the shortest line from your present position to a waypoint, regardless of terrain! It only calculates position, it can’t know what’s between you and your destination, for example. It’s up to you to safely navigate around obstacles, no matter how you’re using this product.

Free Training Aids Available

Now that you know something about the technology that makes this unit possible, you're ready to start learning how to use that technology! This manual will guide you through the process of setting up and running your unit, but that's only one of many resources available.

If you or a friend has Internet access, visit our web site! Find us at WWW.LOWRANCE.COM. The site is packed with additional information on using our products. For instance, you can learn more about interpreting what you see on your sonar screen with our free Sonar Tutorial. The tutorial includes animated illustrations and more pictures of actual sonar returns, all described in detail. There's even a "printer friendly" version of the tutorial available on our web …it makes a great supplement to this operation manual.

Sonar Viewer

You can also download a free copy of our Sonar Viewer software. This PC-based software application plays back any sonar chart log recorded with a Lowrance sonar product. Features include:

Adjustable range, zoom, sensitivity, ColorLine, noise rejection, surface clarity, etc. of the recorded file.

Color interpretation of sonar signals can be user defined.

10

Operates like a Windows Multimedia Player with forward, reverse, pause, fast forward, fast reverse, and scroll buttons.

Adjustments update the entire record displayed.

Can print in full color.

Window can dynamically be sized on your monitor.

Mouse cursor shows GPS position, depth and sounding number anywhere on the visible record.

Unit Emulator

For the ultimate training aid, be sure to download the free emulator software for your unit. Aside from being just plain fun, this program can help you learn both basic and advanced operations without burning boat fuel! Lowrance is the first sonar manufacturer to provide this type of training tool for customers.

This PC application simulates the actual sonar/GPS unit on your computer. You can run it from your computer keyboard or use your mouse to press the virtual keys. Easy download and installation instructions are available on our web site.

Free training emulator is available for your unit on our web site.

The emulator works exactly like your real sonar/GPS unit. Using the Sonar Simulator and GPS Simulator features, it allows you to play back sonar logs, run GPS routes and trails, even create real waypoints you can use in the field! You can even take snapshots of the Sonar Chart and print them or e-mail them to friends.

11

And that's just some of the material available on our web site. To find out all we have available, go to WWW.LOWRANCE.COM and look around. For now, though, we'll get back to how to use this particular unit. And, first, how to use the manual.

How to use this manual: typographical conventions

Many instructions are listed as numbered steps. The keypad and arrow "keystrokes" appear as boldface type. So, if you're in a real hurry (or just need a reminder), you can skim the instructions and pick out what menu command to use by finding the boldface command text. The following paragraphs explain how to interpret the text formatting for those commands and other instructions:

Arrow Keys

The arrow keys control the movement of dotted cross-hair lines on your mapping screen called the cursor. The arrow keys also control a horizontal line depth cursor on the sonar screen. The arrow keys help you move around the menus so you can execute different commands. They are represented by symbols like these, which denote the down arrow key, the up arrow, the left arrow and the right arrow: ↓ ↑ ← →.

Keyboard

The other keys perform a variety of functions. When the text refers to a key to press, the key is shown in bold, sans serif type. For example, the "Enter/Icons" key is shown as ENT and the "Menu" key is shown as MENU.

Menu Commands

A menu command or a menu option will appear in small capital letters, in a bold sans serif type like this: ROUTE PLANNING. These indicate that you are to select this command or option from a menu or take an action of some kind with the menu item. Text that you may need to enter or file names you need to select are show in italic type, such as trail name.

Instructions = Menu Sequences

Most functions you perform with the unit are described as a sequence of key strokes and selecting menu commands. We've written them in a condensed manner for quick and easy reading.

For example, instructions for navigating a trail would look like this:

1.From the Map Page, press MENU|MENU|to MY TRAILS|ENT.

2.Press to Trail 1|ENT|to NAVIGATE|ENT.

12

3.You are asked to wait while it converts the trail into a route.

4.The wait message disappears and the unit begins showing navigation information along the trail. Now, begin moving and follow your unit's directions.

Translated into complete English, step 1 above would mean: "Start on the Map Page. Press the Menu key twice. Next, repeatedly press (or press and hold) the down arrow key to scroll down the menu and select (highlight) the My Trails menu command. Finally, press the Enter key."

Step 2 would mean: "Press the down arrow key repeatedly to scroll to the trail named Trail 1, and press Enter. Next, press the right arrow key to highlight the Navigate command, then press Enter."

13

Notes

14

Section 2:

Installation & Accessories

Preparations

You can install the sonar and GPS systems in some other order if you prefer, but we recommend this installation sequence:

Caution:

You should read over this entire installation section before drilling any holes in your vehicle or vessel!

1.Determine the approximate location for the sonar/GPS unit, so you can plan how and where to route the cables for the antenna, transducer and power. This will help you make sure you have enough cable length for the desired configuration.

2.Determine the approximate location for the transducer and its cable route.

3.Determine the approximate location for the GPS antenna module and its cable route.

4.Determine the location of your battery or other power connection, along with the power cable route.

5.Install the transducer and route the transducer cable to the sonar/GPS unit.

6.Install the GPS antenna and route the antenna cable to the sonar/GPS unit.

7.Install the power cable and route it to the sonar/GPS unit.

8.Mount the sonar/GPS unit to the bracket.

Transducer Installation

These instructions will help you install your Skimmer transducer on a transom, on a trolling motor or inside a hull. These instructions cover both singleand dual-frequency Skimmer transducers. Please read all instructions before proceeding with any installation.

The smaller single-frequency Skimmers typically use a one-piece, stainless steel mounting bracket. The larger dual-frequency Skimmers typically use a two-piece, plastic mounting bracket. The trolling motor mount uses a one-piece plastic bracket with an adjustable strap.

These are all "kick-up" mounting brackets. They help prevent damage if the transducer strikes an object while the boat is moving. If the transducer does "kick-up," the bracket can easily be pushed back into place without tools.

15

Read these instructions carefully before attempting the installation. Determine which of the mounting positions is right for your boat. Remember, the transducer installation is the most critical part of a sonar installation.

NOTE:

The following installation types also call for these recommended tools and required supplies that you must provide (supplies listed here are not included):

Single-frequency transom installations

Tools include: two adjustable wrenches, drill, #29 (0.136") drill bit, flathead screwdriver. Supplies: high quality, marine grade aboveor belowwaterline sealant/adhesive compound.

Dual-frequency transom installations

Tools: two adjustable wrenches, drill, #20 (0.161") drill bit, flat-head screwdriver. Supplies: four, 1" long, #12 stainless steel slotted wood screws, high quality, marine grade aboveor below-waterline sealant/adhesive compound.

Single-frequency trolling motor installations

Tools: two adjustable wrenches, flat-head screwdriver. Supplies: plastic cable ties.

Shoot-through hull installations

Tools: these will vary depending on your hull's composition. Consult your boat dealer or manufacturer. Other tools are a wooden craft stick or similar tool for stirring and applying epoxy, and a paper plate or piece of cardboard to mix the epoxy on. Supplies: rubbing alcohol, 100 grit sandpaper, specially formulated epoxy adhesive available from LEI (see ordering information on the inside back cover). A sandwich hull also requires polyester resin.

Selecting a Transducer Location

1.The location must be in the water at all times, at all operating speeds.

2.The transducer must be placed in a location that has a smooth flow of water at all times. If the transducer is not placed in a smooth flow of water, interference caused by bubbles and turbulence will show on the sonar's display in the form of random lines or dots whenever the boat is moving.

NOTE:

Some aluminum boats with strakes or ribs on the outside of the hull create large amounts of turbulence at high speed. These boats typically have large outboard motors capable of propelling the boat

16

at speeds faster than 35 mph. Typically, a good transom location on aluminum boats is between the ribs closest to the engine.

3.The transducer should be installed with its face pointing straight down, if possible. For shoot-thru applications: Many popular fishing

boat hulls have a flat keel pad that offers a good mounting surface. On vee hulls, try to place the transducer where the deadrise is 10° or less.

Deadrise less than 10°

Strakes

Pad

Left, vee pad hull; right, vee hull. A pod style transducer is shown here, but the principle is the same for Skimmers inside a hull.

4.If the transducer is mounted on the transom, make sure it doesn't interfere with the trailer or hauling of the boat. Also, don't mount it closer than approximately one foot from the engine's lower unit. This will prevent cavitation (bubble) interference with propeller operation.

5.If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps and aerators can be displayed on the sonar's screen. Use caution when routing the transducer cable around these wires.

CAUTION: Clamp the transducer cable to transom near the transducer. This will help prevent the transducer from entering the boat if it is knocked off at high speed.

Good location

 

Poor location

Good

 

location

Good location

Poor angle

 

Good and poor transducer locations.

How low should you go?

For most situations, you should install your Skimmer transducer so that its centerline is level with the bottom of the boat hull. This will

17

usually give you the best combination of smooth water flow and protection from bangs and bumps.

Transom

Transducer centerline

Hull bottom

Align transducer centerline with hull bottom.

However, there are times when you may need to adjust the transducer slightly higher or lower. (The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down.) If you frequently lose bottom signal lock while running at high speed, the transducer may be coming out of the water as you cross waves or wakes. Move the transducer a little lower to help prevent this.

If you cruise or fish around lots of structure and cover, your transducer may be frequently kicking up from object strikes. If you wish, you may move the transducer a little higher for more protection.

There are two extremes you should avoid. Never let the edge of the mounting bracket extend below the bottom of the hull. Never let the bottom – the face – of the transducer rise above the bottom of the hull.

Shoot-thru-hull vs. Transom Mounting

In a shoot-thru-hull installation, the transducer is bonded to the inside of the hull with epoxy. The sonar "ping" signal actually passes through the hull and into the water. This differs from a bolt-thru-hull installation (often called simply "thru-hull"). In that case, a hole is cut in the hull and a specially designed transducer is mounted through the hull with a threaded shaft and nut. This puts the transducer in direct contact with the water.

Typically, shoot-thru-hull installations give excellent high speed operation and good to excellent depth capability. There is no possibility of transducer damage from floating objects, as there is with a transommounted transducer. A transducer mounted inside the hull can't be knocked off when docking or loading on a trailer.

However, the shoot-thru-hull installation does have its drawbacks. First, some loss of sensitivity does occur, even on the best hulls. This varies from hull to hull, even from different installations on the same hull. This is caused by differences in hull lay-up and construction.

18

Second, the transducer angle cannot be adjusted for the best fish arches on your sonar display. (This is not an issue for flasher-style sonars.) Lack of angle adjustment can be particularly troublesome on hulls that sit with the bow high when at rest or at slow trolling speeds.

Third, a transducer CAN NOT shoot through wood and metal hulls. Those hulls require either a transom mount or a thru-hull installation.

Fourth, if your Skimmer transducer has a built in temp sensor, it will only show the temperature of the bilge, not the water surface temp.

Follow the testing procedures listed in the shoot-thru-hull installation section at the end of this lesson to determine if you can satisfactorily shoot through the hull.

TRANSOM TRANSDUCER ASSEMBLY AND MOUNTING

The best way to install these transducers is to loosely assemble all of the parts first, place the transducer's bracket against the transom and see if you can move the transducer so that it's parallel with the ground.

The following instructions sometimes vary depending on the mounting bracket that came with your transducer. Single-frequency Skimmers come with a one-piece stainless steel bracket, while dual-frequency Skimmers come with a two-piece plastic mounting bracket. Use the set of instructions that fits your model.

1.Assembling the bracket.

A. One-piece bracket: Press the two small plastic ratchets into the sides of the metal bracket as shown in the following illustration. Notice there are letters molded into each ratchet. Place each ratchet into the bracket with the letter "A" aligned with the dot stamped into the metal

bracket. This position sets the transducer's coarse angle adjustment for a 14° transom. Most outboard and stern-drive transoms have a 14° angle.

Dot

Align plastic ratchets in bracket.

B. Two-piece bracket: Locate the four plastic ratchets in the transducer's hardware package. Press two ratchets into the sides of the plastic bracket and two on either side of the transducer as shown in the following illustrations. Notice there are letters molded into each ratchet.

19

Place the ratchets into the bracket with the letter "A" aligned with the alignment mark molded into the bracket. Place the ratchets onto the transducer with the letter "A" aligned with the 12 o'clock position on the transducer stem. These positions set the transducer's coarse angle adjustment for a 14° transom. Most outboard and stern-drive transoms have a 14° angle.

Alignment letters

Alignment

positions

Transducer

Transducer bracket

Insert and align ratchets.

Transducer Transducer bracket

Ratchet

Ratchet

 

Add ratchets to bracket and transducer.

2.Aligning the transducer on the transom.

A. One-piece bracket: Slide the transducer between the two ratchets. Temporarily slide the bolt though the transducer assembly and hold it against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground. If it does, then the "A" position is correct for your hull.

20

If the transducer's face isn't parallel with the ground, remove the transducer and ratchets from the bracket. Place the ratchets into the holes in the bracket with the letter "B" aligned with the dot stamped in the bracket.

Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3A. If it doesn't, repeat step 2A, but use a different alignment letter until you can place the transducer on the transom correctly.

Ratchets

Insert bolt and check transducer position on transom.

B. Two-piece bracket: Assemble the transducer and bracket as shown in the following figure. Temporarily slide the bolt though the transducer assembly but don't tighten the nut at this time. Hold the assembled transducer and bracket against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground. If it does, then the "A" positions are correct for your hull.

If the transducer's face isn't parallel with the ground, remove and disassemble the transducer and ratchets. Place the ratchets into the bracket holes with the letter "B" aligned with the bracket alignment mark. Place them on the transducer aligned with the 12 o'clock position on the transducer stem.

Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3B. If it doesn't, repeat step 2B, but use a different alignment letter until you can place the transducer on the transom correctly.

21

Lock washer

Bolt

Nut

Flat washer

Flat washer

Assemble transducer and bracket.

3.Assembling the transducer.

A. One-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the following fig-

ure. Don't tighten the lock nut at this time.

Metal Nut washer

Rubber

Metal washer

washers

 

Bolt

Assemble transducer and bracket.

B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the figure in step 2B. Don't tighten the lock nut at this time.

4.Drilling mounting holes.

Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull!

Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot.

Drill the holes. For the one-piece bracket, use the #29 bit (for the #10 screws). For the two-piece bracket, use the #20 bit (for the #12 screws).

22

Loading...
+ 186 hidden pages