Lowrance electronic HDS-8 000-10537-001, HDS-5 000-10519-001, 000-10776-001, HDS-12, HDS-9 User Manual

...
0 (0)

HDS Gen2Touch

Installation Manual

ENGLISH

lowrance.com

Preface

As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance.

It is the owner’s sole responsibility to install and use the instrument and transducers in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.

NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation. This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and affiliates reserve the right to make changes to specifications without notice.

Copyright

Copyright © 2012 Navico Holding AS.

Warranty

The warranty card is supplied as a separate document.

In case of any queries, refer to the brand web site of your display or system:

www.lowrance.com

Declarations and conformance

This equipment is intended for use in international waters as well as inland waters and coastal sea areas administered by countries of the USA, E.U. and E.E.A.

| 1

Compliance Statements

Lowrance HDS-7, HDS-9, and HDS-12 Gen2 Touch:

meet the technical standards in accordance with Part 15.103 of the FCC rules

comply with CE under RTTE directive 1999/5/EC

comply with the requirements of level 2 devices of the Radiocommunications (Electromagnetic Compatibility) standard 2008

For more information please refer to our website: www.lowrance.com

Warning

The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that of the receiver

Consult the dealer or an experienced technician for help

2 |

About this manual

This manual is a reference guide for installing the Lowrance HDS-7, HDS-9, and HDS-12 Gen2 Touch system.

The manual does not cover basic background information about how equipment such as radars, echo sounders and AIS work. Such information is available from our web site:

http://www.lowrance.com/Support/Library/

Important text that requires special attention from the reader is emphasized as follows:

¼¼ Note: Used to draw the reader’s attention to a comment or some important information.

! Warning: Used when it is necessary to warn personnel that they should proceed carefully to prevent risk of injury and/or damage to equipment/personnel.

Trademarks

‘NMEA 2000’ is a registered trademark of the National Marine Electronics Association

‘Navionics’ is a registered trademark of Navionics SpA

‘Simrad’ is a trademark of Kongsberg Maritime AS Company registered in the US and other countries and is being used under license.

‘HDS’, ‘StructureScan’, ‘Navico’, ‘Lowrance’, ‘SonicHub’, ‘SimNet’ and ‘Skimmer’ are trademarks of Navico, registered in the

US and other countries. ‘InsightHD’, ‘Broadband Radar’ and ‘Broadband Sonar’ are trademarks of Navico.

| 3

Contents

6HDS Gen2 Touch overview

7Front - controls

8Rear - connectors

9SD card slot

10Check the contents

11Display Installation

11Mounting location

12Bracket mounting

13Flush mounting

14Research

14Select a transducer location

15Attaching the transducer

16Adjusting the transducer

17Wiring

17Guidelines

18Power connection

20Transducer connection

21Ethernet device connection

22NMEA 2000 device connection

24NMEA 0183 device connection

25Video In

25Connecting video sources

26 Software setup

26 Sonar installation settings

28Touch Screen Calibration

28Software upgrades

29Dimensional drawings

29HDS 7 Gen2 Touch

29HDS 9 Gen2 Touch

29HDS 12 Gen2 Touch

4 |

30 Accessories

30 NMEA 2000

30Transducers

31Ethernet cables

31Display parts

33Supported data

33NMEA 2000

34NMEA 0183

35Specifications

| 5

1 HDS Gen2 Touch overview

The HDS-7, HDS-9, and HDS-12 Gen2 Touch multifunction displays are available with or without inbuilt sonar and structure scan. The ability to network over NMEA 2000 and ethernet allows access

to data as well as control of numerous optional devices that can provide sonar, radar, audio entertainment, weather and even digital switching.

All displays are charting ready, with built-in GPS receiver and Insight cartography (region dependent) and with optional Navionics support via an SD card slot.

The displays may be mounted on to the vessel with the supplied surface mount bracket, or flush mounted in to the dash.

Power should be supplied at around 12V, but due to the variable nature of boat power systems, the displays are designed to operate on 10.8 V - 17 V.

6 |

HDS Gen2 Touch overview | HDS Gen2 Touch Installation Manual

Front - controls

1

2

1Touchscreen

2Card reader door

3Pages key

4Zoom in / Zoom out key

5Mark / Waypoint key

6Power key

3

4

5 6

HDS Gen2 Touch overview | HDS Gen2 Touch Installation Manual

| 7

Rear - connectors

A B

1

2

3

4

4

5

4

5

1

2

3

AHDS-9 & 12 connector arrangement

BHDS-7 connector arrangement

1Sonar

2StructureScan - connects to LSS-2 HD Transducer

3Power - also video for HDS-9 & 12, with optional adaptor

4Ethernet - two ports on HDS-9 & 12, one on 7

5NMEA 2000

8 |

HDS Gen2 Touch overview | HDS Gen2 Touch Installation Manual

SD card slot

Used for optional Navionics or InsightHD chart data, software updates, transfer of user data and system backup.

The card reader door is opened by lightly pressing and sliding the door to the left, then pulling forward from the left side.

The card reader door should always be shut immediately after inserting or removing a card, in order to prevent possible water ingress.

¼¼ Note: The HDS-9 and 12 Displays have two card readers, the HDS-7 has one.

HDS Gen2 Touch overview | HDS Gen2 Touch Installation Manual

| 9

Lowrance electronic HDS-8 000-10537-001, HDS-5 000-10519-001, 000-10776-001, HDS-12, HDS-9 User Manual

2

Check the contents

Display

Bracket knobs (x2)

Front Bezel (attached to unit)

Power cable

Sun cover

Fasteners - #6 x 1.5” (4x)

Mounting bracket

Parts Included, dependent on model

83/200 KHz transducer

LSS-2 HD transducer

50/200 KHz transducer

DVD - manuals

10 |

Check the contents | HDS Gen2 Touch Installation Manual

Loading...
+ 28 hidden pages