Livarno 4280-042L, 4281-048L User Manual [en, cs, pl, de]

LED  PENDANT LAMP

LED  PENDANT LAMP	WISZĄCA LAMPA LEDOWA
Operation  and Safety Notes	Wskazówki dotyczące obsługi i bezpieczeństwa
LED  ZÁVĚSNÉ SVÍTIDLO	LED-PENDELLEUCHTE
Pokyny  pro obsluhu a bezpečnostní pokyny	Bedienungs - und Sicherheitshinweise

IAN 65339

Before  reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Przed  przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi funkcjami urządzenia.

Před  čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Klappen  Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen  des Gerätes vertraut.

GB	Operation and Safety Notes	Page	5
PL	Wskazówki dotyczące obsługi i bezpieczeństwa	Strona	9
CZ	Pokyny pro obsluhu a bezpečnostní pokyny	Strana	13
DE / AT / CH	Bedienungsund Sicherheitshinweise	Seite	17

A

1	4280-042L / 4281-048L
2
3	6
4
5

7

9	8
10
11
12	4280-042L

		9	4281-048L
	12	10
		11

B

13 14

LED pendant lamp

Introduction

Congratulations on your new product. You have selected a high quality product. Please be sure to carefully read the com-

plete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.

Intended use

This light is only suitable for indoor use in dry and enclosed spaces. The light can be fastened to any normally inflammable surface.

Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 LED pendant light, model 4280-042L / 

4281-048L

4 (4280-042L) or 1 (4281-048L) pieces of lamp glass

8 (4280-042L) or 2 (4281-048L) screws for lamp glass

8 (4280-042L) or 2 (4281-048L) washers (metal) 8 (4280-042L) or 2 (4281-048L) washers (rubber) 1 Allen key

1 Philips screwdriver

1 Rope smoother

2 Screws

2 Rawlplugs

1 Set of instructions for use

Introduction / Safety

Parts description

1Mounting bracket

2Rawlplug

3Screw (mounting bracket)

4Connection housing

5Screw (connection housing)

6Rope smoother

7Counterweight

8Bushing

9Lamp glass

10Washer (rubber)

11Washer (metal)

12Screw (lamp glass)

13Terminal block

14Protective tube

Technical Data

Item no.:	4280-042L / 4281-048L
Operating voltage:	230–240 V 50 Hz
Illuminant:	4 LED modules (LEDs not
	replaceable)
Rated power:	4 x 5.5 W
Protection class:	II /
Protection type:	IP20

Safety

Safety information

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

Only use the included parts, using other parts will void the warranty.

Avoid the risk of fatal injury from electric shock

GB 5

Safety / Start-up

Ensure that a qualified electrician, or a person trained to carry out electrical installations, performs the electrical installation.

We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions! Never use the light if any defects have been identified.

Prior to installation, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box. Ensure that the light does not come into contact with water or other liquids under any circumstances.

Prior to installation verify the mains voltage on site corresponds with the operating voltage required for the light (230–240 V ).

Ensure that no cables are damaged when installing.

Prevent fire and injury hazards

To prevent burns, ensure that the light is switched off and has cooled down before touching it. Do not attach the light to a damp or conductive substrate.

Do not leave the light or packaging material lying unattended. Plastic film/bags, plastic parts etc. can turn into dangerous toys for children. Do not look directly into the light source (light bulb, LED etc.).

Safe working

Install the light so that it is protected from moisture, dirt and excessive heating.

Always be attentive! Always pay attention to what you are doing and use common sense. Never use the light if you are having difficulty concentrating or do not feel well.

Familiarise yourself before use with all instructions and diagrams in this manual as well as with the light itself.

This light is not suitable for dimmer or electronic switches.

The illuminant is not replaceable.

6 GB

Start-up

Mounting the light

CAUTION! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before installing. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).

Remove the visible screws 5 on the side of the

connection housing 4 and take off the mounting bracket 1 on the rear (see fig. A).

Use the slotted holes intended for the mounting bracket 1 to mark the holes for the screws 3 . Now drill the mounting holes. Ensure that you do not damage the supply line.

Insert the dowels		2		into the holes. Fasten the
mounting bracket				with the provided screws
		1
3	.

Open the junction box.

Feed the power cord through the protective tube 14 .

Connect the connection cable of the light to the power cord using the terminal block 13 (see Fig. B).

Be sure to correctly connect the individual conductors of the power cord (external): live conductor, black or brown = symbol L, neutral conductor, blue = symbol N.

Be sure the protective tube 14 is secured in the bracket of the junction box.

Close the junction box.

Use the screws 5 to fasten the luminaire to the mounting bracket 1 .

Now screw the lamp glass (4280-042L) 9 or (4281-048L) using the screws 12 , the washers (metal) 11 and the washers (rubber) 10 to the light.

If necessary, smooth the ropes with the rope smoother 6 .

Replace the fuse or switch on the circuit breaker in the fuse box (Position I).

Your light is now ready to use.

Start-up / Maintenance and Cleaning / Disposal / Information

Adjusting the height

Extending:

Press in the bushings 2 - 3 mm. Be careful not to push the bushings all the way in.

Allow the counterweight 7 to slide up.

Shortening:

Lift the light whilst pulling the counterweight 7 down.

Shortening the ropes:

Loosen the socket head screws at the end of the rope.

Adjust the rope to the desired maximum length.

Tighten the socket head screw. Trim the excess rope.

Maintenance and Cleaning

CAUTION! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before cleaning. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).

Only use a dry, lint-free cloth for cleaning. Do not use solvents, spirit or similar substances. They could damage the light.

Allow the light to cool down all the way.

Disposal

The package and packaging materials consist entirely of environmentally friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the

line through it means that, in the European Union, the product has to be disposed

of in a separate refuse collection. This applies to the product and to all components bearing this symbol. Do not dispose of products bearing this symbol in your normal household waste, but instead they must be taken for recycling to a collection site for electrical and electronic appliances. Recycling

helps to reduce the consumption of raw materials and protects the environment.

Information

Warranty

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the appliance to the listed Service Centre address, making reference to the following article number: 4280-042L / 4281-048L. Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Declaration of conformity

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004 / 108/EC, Low Voltage Directive 2006 / 95 / EC, Ecodesign Directive 2009 / 125 / EC, RoHS Directive 2011 / 65 / EU). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer / Service

Briloner Leuchten GmbH Im Kissen 2,

59929 Brilon, Germany

Tel.: [phone] / 97 12–0 Fax: [phone] E-Mail: [e-mail] www.briloner.de

GB 7