Livarno 1321-012L or 1322-022L User Manual [en, cs, pl, de]

Loading...

LED  FLOOR LAMP

LED  FLOOR LAMP

LEDOWA  LAMPA STOJĄCA

Operation  and Safety Notes

Wskazówki  dotyczące obsługi i bezpieczeństwa

LED  STOJACÍ LAMPA

LED  STOJACA LAMPA

Pokyny 

pro obsluhu a bezpečnostní pokyny

Pokyny  pre obsluhu a bezpečnostné pokyny

LED -STEHLEUCHTE

Bedienungs - und Sicherheitshinweise

IAN 103124

Before  reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Przed  przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi funkcjami urządzenia.

Před  čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred  čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen  Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen  des Gerätes vertraut.

GB

Operation and Safety Notes

Page

5

PL

Wskazówki dotyczące obsługi i bezpieczeństwa

Strona

9

CZ

Pokyny pro obsluhu a bezpečnostní pokyny

Strana

13

SK

Pokyny pre obsluhu a bezpečnostné pokyny

Strana

17

DE / AT / CH

Bedienungsund Sicherheitshinweise

Seite

21

Livarno 1321-012L or 1322-022L User Manual

 

1

 

 

1

 

2

 

7

2

 

3

 

 

3

 

4

 

 

4

6

5

 

6

5

1321-012L

 

1322-022L

 

A

4a

B

1321-012L

1322-022L

 

 

 

ON/OFF

ON/OFF

 

4b

 

 

 

 

 

 

12

12

 

 

C

 

 

 

 

 

3a

 

 

8

 

 

 

6

 

 

 

 

 

9

 

3

 

 

10

 

 

 

 

11

 

 

 

LED Floor Lamp

Introduction

Congratulations on your new product. You have selected a high quality product. Please be sure to carefully read the com-

plete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.

Intended use

This light is only suitable for indoor use in dry and enclosed spaces. This product is intended for private household use only.

Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1

Floor lamp, model 1321-012L or 1322-022L

1

Base

1

Chrome plating

1

Tool

1

Instructions for use

Parts description

1Reflector

2Lamp arm

3Fixing lever 3a Locating screw

4Stand tube

4 a Upper support tube

Introduction / Safety

4b Lower support tube

5Mains cable

6Base

7Adjustment lever (model 1322-022L)

8Chrome plating

9Plain washer

10Nut

11Tool

12ON / OFF switch

Technical Data

Model no.:

1321-012L or 1322-022L

Operating voltage:

230–240 V 50 Hz

Lamp:

1 LED module about 6 W

 

(1321-012L) (LED not

 

replaceable)

 

2 LED module, each about

 

5 W (1322-022L) (LED not

 

replaceable)

Protection class:

II / 

Safety

Safety information

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

Avoid the risk of fatal injury from electric shock

Check the light for damage every time before you use it. Never use the light if it shows any signs of damage.

CAUTION! A damaged light means danger of death from electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.

GB 5

Safety / Start-up

To prevent hazards, a damaged flexible outer lead on this lamp must be replaced by the manufacturer, its service representative or an equally qualified professional!

Before use, verify the available mains voltage corresponds with the operating voltage of the lamp (230–240 V ).

Ensure that the light does not come into contact with water or other liquids under any circumstances.

Always unplug from the mains before assembling, disassembling, cleaning, or if the lamp will not be used for extended periods.

Never open any of the components of the electrical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.

The illuminant is not replaceable.

This light is not suitable for dimmer or electronic switches.

Prevent fire and injury hazards

RISK OF INJURY! Check every illuminant for damage immediately upon unpacking. Do not install the light if the illuminants are defective.

In this case contact the service centre for a replacement.

Do not look directly into the light source (light bulb, LED etc.).

Do not leave the light or packaging material lying unattended. Plastic film or bags, plastic parts etc. can turn into dangerous toys for children.

Do not cover the lamp or the mains plug with objects. Excessive heat can result in a fire. Never leave the lamp unattended whilst in use.

Safe working

Mount the light so that it is protected from moisture and dirt.

Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach.

6 GB

Always be attentive! Always pay attention to what you are doing and use common sense. Never assemble the lamp if you are unfocused or feel unwell.

Start-up

Mounting the light

Note: When assembling the stand tube 4 be sure not to damage the mains lead 5 inside the lamp.

Unfold the floor lamp.

Insert the upper stand tube section 4a into the lower stand tube section 4b .

Carefully pull the mains cable 5 out of the stand tube 4 .

Place the chrome plating 8 on the base 6 .

Put the stand tube

4

through the chrome plat-

ing

8

into the base

6

and fasten the stand

tube

 

 

 

by turning clockwise.

 

4

Place the plain washer

 

 

and the nut

 

on

9

10

the thread and use the tool

 

 

to screw it tight.

11

Model 1322-022L: Screw the adjustment

lever

7

onto the reflector

1

. You will need a

small screwdriver to do this.

Plug the mains plug into a socket that has been professionally installed.

Your light is now ready to use.

Switching the lamp on / off

Switch the lamp on or off using the ON/OFF switch 12 .

Adjusting the reflector

Note: Only adjust the reflector 1 with the light switched off.

Allow the lamp to cool off completely.

Turn the lamp arm 2 to the desired position. Note: Re-tighten the locking lever 3 if the lamp arm 2 changes in position.

... / Maintenance and Cleaning / Disposal / Information

Turn the reflector 1 to the desired angle.

Note: Re-tighten the locating screws 3a if the lamp reflector 1 changes in position. You will need a fitting screwdriver to do this.

Maintenance and Cleaning

DANGER OF ELECTRIC SHOCK! First unplug the mains plug from the socket.

CAUTION! DANGER OF BURN INJURIES!

Allow the lamp to cool down completely.

DANGER OF ELECTRIC SHOCK! For electrical safety, never clean the light with water or other liquids, or immerse it in water.

Do not use solvents, benzene or similar substances. They could damage the light. Only use a dry, lint-free cloth for cleaning.

Disposal

The package and packaging materials consist entirely of environmentally friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the

line through it means that, in the European Union, the product has to be disposed

of in a separate refuse collection. This applies to the product and to all components bearing this symbol. Do not dispose of products bearing this symbol in your normal household waste, but instead they must be taken for recycling to a collection site for electrical and electronic appliances. Recycling helps to reduce the consumption of raw materials and protects the environment.

Information

Warranty

been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the appliance to the listed Service Centre address, making reference to the following article number: 1321-012L / 1322-022L.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Manufacturer / Service

Briloner Leuchten GmbH Im Kissen 2,

59929 Brilon, Germany

Tel.: +49 (0) 29 61 / 97 12–0 Fax: +49 (0) 29 61 / 97 12–199 E-mail: Info@briloner.de www.briloner.de

IAN 103124

Please have your receipt and the article number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.

Declaration of conformity

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004 / 108 / EC, Low Voltage Directive 2006 / 95 / EC, Ecodesign Directive 2009 / 125/EC, RoHS Directive 2011 / 65 / EU). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has

GB 7

8

+ 17 hidden pages