Page 1
Installation Instructions
VAP
READ AND FOLLOW ALL SREAD AND FOLLOW ALL SAFETY INSTRUCTIONS!
sAVE THESE INSTTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
SAVE TREAD AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
AFTER INSTALLATIONHESE INSTRUCTIONS AND DELIVER TO OWNER
WARNING
AFTER INSTALLATIONAREAD AND FOLLOW ALL SAFETY INSTRUCTIONS!
To reduce the risk of death, injury or property damage from fire, electric shock, cuts,
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION FETY INSTRUC-
abrasions, falling parts, and other hazards:
• Service of the equipment must be performed by qualified service personnel.
• Installation and maintenance must be performed by a person familiar with the construction
and operation of this product and any hazards involved. All applicable codes and ordinances
must be followed.
• Read this document before installing, servicing, or maintaining this equipment or installing a
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION NSTALLATION
lamp. These instructions do not cover all installation, service, and maintenance situations. If
your situation is not covered, or if you do not understand these instructions or additional
information is required, contact Lithonia Lighting or your local Lithonia LIghting Distributor.
IMPORTANT SAFETY INSTRUCTIONS
TIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER
AFTER IREAD AND FOLLOW ALL SAFETY INSTRUCTIONS!
• Read and follow all warnings and instructions provided by the lamp manufacturer.
WARNING
Before installing, servicing, or maintaining this equipment, follow these general precautions.
To reduce the risk of electrocution:
• Make sure the equipment is properly grounded.
• Always de-energize the circuit and/or equipment before connecting to, disconnecting
from, or servicing the equipment.
To reduce the risk of fire:
• Keep material away that can burn from hot lamp.
• Make sure lamps are correctly installed.
• Use supply conductors with a minimum installation temperature rating as specified
on equipment.
To reduce the risk of personal injury from cuts, abrasions, or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from
carton, handling and maintaining this equipment.
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens.
These substances may damage equipment and cause parts to eventually break and
fall.
• Do not install a damaged fixture.
CAUTION: Observe lamp manufacturer’s recommendations and restrictions on lamp operation,
including but not limited to ballast type, burning position, replacement and cycling. Use only lamps
that comply with applicable ANSI standards.
NOTICE: If lamp is marked it contains mercury. Follow disposal laws. See
www.lamprecycle.org
Lithonia Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for claims arising out of
improper or careless installation or handling of this product.
SAVE THESE INSTRUCTIONS
Lithonia Lighting
INDUSTRIAL VALUE STREAM
One Lithonia Way, Conyers, GA 30012
Phone: 800-315-4963 Fax: 770-981-8141
www.lithonia.com
Part Number: U21316
Revision Date: 03/2010
Page 2
Installation Instructions
VAP
V AP JUNCTION BOX SNAP BRACKET (JMB) INSTALLATION
INSTRUCTIONS
1. Attach JSB bracket (Fig 9) to junction box.(hardware provided by others).
Remove protective film from gasket (included with JSB) and attach adhesive side
to the JSB.
2. If field installing, remove diffuser, lamps and channel cover. Using a 7/8” hole
saw drill out access hole in the center of the fixture housing for electrical connection. Remove KO from channel.
3. If field installing the JMB bracket mounting, attach two (2) brackets to fixture
housing as shown in Fig 10 (maximum 25 inch-pounds torque on screws).
4. Attach on side of fixture bracket to JSB, rotate fixture up until it snaps into the
JSB. Secure JSB to fixture using the screw provided (Fig 11).
5. Make electrical connections and re-install the channel cover, lamps and
diffuser.
Fig 10
Fig 9
Fig 11
VAP MOTION SENSOR INSTALLA TION INSTRUCTIONS
1. Install wet location fitting in end of fixture.
2. Thread extension adapter for sensor into the wet
location fitting.
3. Wire sensor into the fixture as shown in Fig 12.
Fig 12
Lithonia Lighting
INDUSTRIAL VALUE STREAM
One Lithonia Way, Conyers, GA 30012
Phone: 800-315-4963 Fax: 770-981-8141
www.lithonia.com
Part Number: U21316
Revision Date: 03/2010
Loading...