Linksys EZXS16W User Manual

0 (0)

USER GUIDE

EtherFast 10/100 5/8/16-Port

Workgroup Switch

Models: EZXS55W v4.2, EZXS88W v3.4, EZXS16W v2.3

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.

WEB: This globe icon indicates a noteworthy website address or e-mail address.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksysbycisco.com

Linksys www.linksysbycisco.com/international

International

Glossary www.linksysbycisco.com/glossary

Network www.linksysbycisco.com/security

Security

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Other brands and product names are trademarks or registered trademarks of their respective holders. Copyright © 2009 Cisco Systems, Inc. All rights reserved.

EtherFast 10/100 5/8/16-Port Workgroup Switch

Table of Contents

Chapter 1: Product Overview			1
Front Panel			1
Back Panel . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	.	. 1
Chapter 2: Connecting the Switch			2
Instructions . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	.	. 2
Appendix A: Troubleshooting			3
Appendix B: Specifications			4
Appendix C: Warranty Information			5
Limited Warranty			5
Appendix D: Regulatory Information			7
FCC Statement . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	.	. 7
Safety Notices			7
Industry Canada Statement . . . . . . . . . . . .	. . . . . . . . . . . .	. .	7
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE)			8
Appendix E: Software End User License Agreement			12
Cisco Products . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	.	12
Software Licenses . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. .	12

EtherFast 10/100 5/8/16-Port Workgroup Switch

Chapter 1

Product Overview

Chapter 1:

Product Overview

Thank you for choosing the EtherFast® 10/100 5/8/16-Port Workgroup Switch. The EtherFast® 10/100 Workgroup Switch is an easy, affordable way to build a fast, reliable desktop Ethernet network. Connect up to 5, 8, or 16 devices—computers, storage, modems and printers— with performance that helps you get more done faster.

Front Panel

Front Panel of EZXS55W

Front Panel of EZXS88W

Front Panel of EZXS16W

Power (Green) Each time your Switch powers up, it will run a diagnostic/self-test. After the test, the Power LED will light up and will stay on while the Switch is powered on.

Link/Act (Green) This LED lights up solid when the Switch is connected to a device through the Ethernet port. If the LED is flashing, the Switch is sending or receiving data over that port.

100 (Green) This LED indicates the speed of the connection over the Ethernet port. When the LED lights up, the speed is 100 Mbps. When the LED does not light up, the speed is 10 Mbps.

Full/Col (Yellow) This LED indicates if the Ethernet port is in full or half duplex mode.When the LED is lit, the mode is Full Duplex. When the LED is not lit, the mode is Half Duplex. When the LED flashes, the port has a data collision error; check if your cabling is installed properly and all connections are secure.

Back Panel

Back Panel of EZXS55W

Back Panel of EZXS88W

Back Panel of EZXS16W

Ethernet 1-5 (EZXS55W),

Ethernet 1-8 (EZXS88W),

Ethernet 1-16 (EZXS16W) The Ethernet ports connect the Switch to a wired PC or other Ethernet network device.

Uplink (EZXS55W and EZXS88W only) The Uplink port connects the Switch to a router or to another switch.

MDI/MDIX (EZXS16W only) When the MDI/MDIX button is pressed in, port 16 will function as an Uplink port. When this button is not pressed in, port 16 functions as a normal 10/100 port.

Power The Power port is where you will connect the power adapter.

NOTE TO USERS OF 10/100 5- OR 8-PORT SWITCH (EZXS55W OR EZXS88W): If you connect a router or additional switch to the Uplink port, then you cannot use the numbered port next to the Uplink port (port 5 on the 5-Port Switch or port 8 on the 8-Port Switch will be inactive). The two ports are wired together, so they cannot be used simultaneously.

EtherFast 10/100 5/8/16-Port Workgroup Switch

Chapter 2

Connecting the Switch

Chapter 2:

Connecting the Switch

This chapter explains how to connect devices to the Switch. You will connect computers to the Switch before connecting a router or additional switch to the Uplink port. (The 10/100 5-Port Switch is shown in the connection pictures.)

Instructions

1.Make sure all of the devices you will connect to the Switch are powered off.

2.Connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. Then connect the other end to a computer.

Connect to a computer

NOTE TO USERS OF THE 10/100 5- OR 8-PORT SWITCH: If you connect a router or additional switch to the Uplink port, then you cannot use the numbered port next to the Uplink port (port 5 on the 5-Port Switch or port 8 on the 8-Port Switch will be inactive). The two ports are wired together, so they cannot be used simultaneously.

3.Repeat step 2 to connect additional computers.

4.Connect a Category 5 Ethernet network cable to the Uplink port. Then connect the other end to a router or additional switch.

Connect a Router or Switch

EtherFast 10/100 5/8/16-Port Workgroup Switch

NOTE TO USERS OF THE 10/100 16-PORT SWITCH:The 10/100 16-Port Switch is equipped with a crossover button labeled MDI/MDIX. This enables port 16 to be used as the Switch’s uplink port. The MDI/MDIX button must be pressed in if you want to use port 16 as an uplink port. Otherwise, port 16 will function as a normal 10/100 port.

5.Connect the supplied power adapter to the power port on the Switch. Then plug the other end into an electrical outlet.

Connect the Power

6.Power on the devices connected to the Switch. Each active port’s corresponding LED will light up on the Switch’s front panel.

Congratulations! The installation of the Switch is complete.

Appendix A

Troubleshooting

Appendix A:

Troubleshooting

I can’t connect to the Internet.

1.Verify the proper LEDs are lit on the Switch.

•• Make sure the Power LED has a steady green light and is not flashing.

•• Verify the Ethernet LED has a fairly steady green light. It will flash occasionally, indicating activity.

2.Power down everything, and power on each device in the following order:

•• Switch

•• PC

WEB: If your questions are not addressed here, refer to the Linksys website, www.linksysbycisco.com

EtherFast 10/100 5/8/16-Port Workgroup Switch

Appendix B

Specifications

Appendix B:

Specifications

EZXS55W

Model	EZXS55W (10/100 5-Port
	Workgroup Switch)
Version	4.2
Standards	IEEE 802.3, IEEE802.3u
Ports	Five 10/100 RJ-45 Ports,
	One Shared RJ-45 Uplink Port
LEDs	Power, Link/Act, Full/Col, 100*
	(*per port)
Cabling Type	UTP Category 5 or better

Environmental

Dimensions	4.33" x 1.26" x 3.43"
	(110 x 32 x 87 mm)
Weight	6.00 oz (170 g)
Power	7.5V DC, 700 mA
Certification	FCC Class B, CE, ICES-003
Operating Temp.	32 to 104ºF (0 to 40ºC)
Storage Temp.	-4 to 158ºF (-20 to 70ºC)
Operating Humidity	10 to 85% Noncondensing
Storage Humidity	5 to 90% Noncondensing

EZXS88W

Model	EZXS88W (10/100 8-Port
	Workgroup Switch)
Version	3.4
Standards	IEEE 802.3, IEEE802.3u
Ports	Eight 10/100 RJ-45 Ports,
	One Shared RJ-45 Uplink Port
LEDs	Power, Link/Act, Full/Col, 100*
	(*per port)
Cabling Type	UTP Category 5 or better

Environmental

Dimensions	6.30” x 1.38” x 4.33"
	(160 x 35 x 110 mm)
Weight	8.82 oz (250 g)
Power	9V DC, 800 mA
Certification	FCC Class B, CE, ICES-003
Operating Temp.	32 to 104ºF (0 to 40ºC)
Storage Temp.	-4 to 158ºF (-20 to 70ºC)
Operating Humidity	10 to 85% Noncondensing
Storage Humidity	5 to 90% Noncondensing

EZXS16W

Model	EZXS16W (10/100 16-Port
	Workgroup Switch)
Version	2.3
Standards	IEEE 802.3, IEEE802.3u
Ports	Sixteen 10/100 RJ-45 Ports
Buttons	One MDI/MDIX Button
LEDs	Power, Link/Act, Full/Col, 100*
	(*per port)
Cabling Type	UTP Category 5 or better

Environmental

Dimensions	7.24” x 2.52” x 5.98”
	(184 x 64 x 152 mm)
Weight	16.93 oz (480 g)
Power	12V DC, 1A
Certification	FCC Class B, CE, ICES-003
Operating Temp.	32 to 104ºF (0 to 40ºC)
Storage Temp.	-4 to 158ºF (-20 to 70ºC)
Operating Humidity	10 to 85% Noncondensing
Storage Humidity	5 to 90% Noncondensing

Specifications are subject to change without notice.

EtherFast 10/100 5/8/16-Port Workgroup Switch

Appendix C

Warranty Information

Appendix C:

Warranty Information

Limited Warranty

Linksys warrants this Linksys hardware product against defects in materials and workmanship under normal use for the Warranty Period, which begins on the date of purchase by the original end-user purchaser and lasts for the period specified below:

•• One (1) year for new product

•• Ninety (90) days for refurbished product

Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to

(a)repair the product with new or refurbished parts,

(b)replace the product with a reasonably available equivalentneworrefurbishedLinksysproduct,or(c)refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and parts that are replaced become the property of Linksys.

Linksys additionally warrants that any media on which the software may be provided will be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of original purchase. Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to

(a) replace the software media, or (b) refund the purchase price of the software media.

Exclusions and Limitations

This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys,

(c) the product damage was caused by use with nonLinksys products, (d) the product has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident, (f) the serial number on the Product has been altered, defaced, or removed, or

(g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or license fee.

EXCEPTFORTHELIMITEDWARRANTYONMEDIASETFORTH ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND. Without limiting the foregoing, Linksys does

not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT OR SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Obtaining Warranty Service

If	you have	a	question	about	your	product
or	experience	a	problem	with it,	please	go to

www.linksysbycisco.com/support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksysbycisco.com. Have your product serial number and proof of purchase on hand when calling. A

EtherFast 10/100 5/8/16-Port Workgroup Switch

Appendix C

Warranty Information

DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS. If you are requested to return your product, you will be given a Return Materials Authorization (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include the RMA number and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys. Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge. Customers outside of the United States of America and Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys’ then-current rates.

Technical Support

This limited warranty is neither a service nor a support contract. Information about Linksys’ current technical support offerings and policies (including any fees for support services) can be found at www.linksysbycisco.com/support.

This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

EtherFast 10/100 5/8/16-Port Workgroup Switch

+ 19 hidden pages