Linear WOR User Manual

WOR

Wiegand

Output

Receiver

Installation

Instructions

[phone] • FAX [phone]

USA & Canada [phone] & [phone]

Toll Free FAX [phone]

www.linearcorp.com

1.OPEN CASE

OPEN CASE FROM

ANTENNA END

BOARD SLIDES OUT
FROM 3RD SLOT UP	REMOVE FOUR
INSIDE CASE	SCREWS AND WASHERS

3.SET VOLTAGE INPUT JUMPER

PLACE VOLTAGE INPUT JUMPER
IN THIS POSITION TO SELECT A	PLACE VOLTAGE INPUT JUMPER
8-24 VOLT DC INPUT FROM THE	IN THIS POSITION TO SELECT A
ACCESS CONTROL PANEL	REGULATED 5 VOLT DC INPUT
	FROM THE ACCESS CONTROL
	PANEL

5.SET TRANSMITTER FACILITY CODE

SET XMTR FACILITY CODE SWITCHES TO MATCH THE FACILITY CODE PRE-PROGRAMMED INTO TRANSMITTER BLOCK

XMTR FACILITY						SWT0		SWT1		SWT2		SWT3
CODE SWITCHES
					0
					1
					2
					3
					4
TRANSMITTER BLOCK					5
FACILITY CODE 0-15					6
					7
(ASSIGNED WHEN					8
TRANSMITTER BLOCK IS					9
ORDERED FROM LINEAR)					10
					11
		=SWITCHON			12
					13
		=SWITCHOFF			14
					15
NOTE: THE FACTORY SETTINGS
OF FACILITY CODE "0" WILL
ALLOW VALIDATION OF ANY
TRANSMITTER FACILITY CODE

INTRODUCTION

The Model WOR remote radio receiver is designed for use as an access control interface for Linear’s block coded digital transmitters. The unit receives signals from transmitters, adds a facility code to the data, and sends the information to the Wiegand input of the access control panel via a 5-wire connection.

Several transmitter and receiver options can be set using the unit’s dipswitches. Three different Wiegand output formats (26, 30, & 31-bit) are supported. Three receiver options (lockout, hold, & button offset) can be set. Transmitter buttons on multi-button units can be selectively disabled. The facility code is set using 16 dipswitches.

Three antenna types can be used with this receiver. The local whip antenna (supplied) screws directly on to the receiver. The directional (EXA-2000) and omni-directional (EXA-1000) remote antennas attach to the receiver’s antenna input via RG-59 cable and a type “F” connector.

An on-board RADIO RANGE knob allows adjustment of the receiver’s gain. It can be set to limit the maximum radio range that the receiver can achieve. Two indicators display the receivers performance and operation. The red RADIO indicator lights when the receiver detects a radio signal. The two color red/green STATUS indicator lights green when the receiver is sending Wiegand data and during the 1-second post receiver lockout timer (if receiver lockout is enabled). The indicator turns red when the receiver’s HOLD input (connected to the access control panel) is active. Receiver test points are provided for listening to the incoming signals with an audio amplifier.

Power input to the receiver can be either regulated 5 volts or 8-24 volts DC (jumper selected).

The receiver is housed in a weather-resistant enclosure and can be mounted indoors or outdoors. Gaskets and a weather-tight wiring strain relief seal the unit from the elements.

2.LOCATE COMPONENTS

		ANTENNA
	RADIO RANGE KNOB	CONNECTOR
		(HIDDEN)
	(CLOCKWISE FOR
	MAXIMUM GAIN)
		INPUT
	MAX	VOLTAGE
		JUMPER
		PROGRAM
		BUTTON

OPTION

DIPSWITCHES POWER AND DATA TERMINALS

	RADIO	GND	AUDIO	STATUS INDICATOR
				RED = HOLD, GREEN = DECODE

TEST POINTS

RADIO INDICATOR

4.SET OUTPUT FORMAT & RECEIVER OPTIONS

WIEGAND OUTPUT FORMAT

SWITCH 1 26-BIT SELECT THE WIEGAND OUTPUT FORMAT

SWITCH 2 30-BIT THAT MATCHES THE ACCESS CONTROL

SWITCH 3 31-BIT SYSTEM BEING USED

BUTTON OFFSET TABLE

LEFT	RIGHT	TOP	BOTTOM LEFT OR RIGHT
0	16384	32768	49152

RECEIVER OPTIONS

SWITCH 1 - LOCKOUT DISABLE

OFF - (FACTORY SETTING) CAUSES RECEIVER TO IGNORE TRANSMITTER SIGNALS FOR ONE SECOND AFTER A VALIDATED TRANSMISSION. ON - ALLOWS RECEIVER TO PASS WIEGAND DATA INSTANTLY WITH EACH VALIDATED TRANSMISSION.

SWITCH 2 - HOLD ENABLE

OFF - (FACTORY SETTING) HOLD INPUT SIGNALS ARE IGNORED.

ON - WHEN HOLD INPUT IS ACTIVE, ANY WIEGAND DATA WILL BE HELD FOR A MAXIMUM OF ONE SECOND THEN DISCARDED UNLESS THE HOLD INPUT IS RELEASED DURING THE ONE SECOND TIME.

SWITCH 3 - BUTTON OFFSET ENABLE

OFF - (FACTORY SETTING) TRANSMITTERS PASS THEIR ID NUMBER TO THE WIEGAND OUTPUT WITHOUT ANY CHANGES. ON - THE TRANSMITTER ID IS OFFSET TO THE RANGE ABOVE, BASED ON WHICH BUTTON IS PRESSED.

6.SET TRANSMITTER BUTTON OPTIONS

		BOTH
		FUNCTION
		AS LEFT	TOP
		BUTTON	BUTTON
		LEFT	RIGHT
			BUTTON
		BUTTON
		TOP
	BUTTON
			RIGHT
	LEFT	BUTTON
	BUTTON		BOTTOM-RIGHT
	BOTTOM-LEFT
			BUTTON
	BUTTON
			RIGHT
			BUTTON
	LEFT	LEFT
	BUTTON
		BUTTON

THE FACTORY SETTING ALLOWS ALL

TRANSMITTER BUTTONS TO OPERATE

SET XMTR BUTTON DISABLE SWITCH(ES) ON TO PREVENT SELECTED TRANSMITTER BUTTONS FROM OPERATING

SWITCH 4 - TOP

SWITCH 5 - BOTTOM RIGHT

	OPERATE	SWITCH 6 - BOTTOM LEFT
	AS TOP
		SWITCH 7	- RIGHT OR TOP RIGHT
	BUTTON
		SWITCH 8	- LEFT OR TOP LEFT