|
|
|
IS:4531 |
|
4551, and 4552 Series Fixtures. |
|
|||
Instructions for Installation of Arco™ 4531, 4532, 4533, |
|
|
|
|
|
|
|
Page 1 of 2 |
0995 |
|
|
|
||
|
|
|
|
|
Read and understand these instructions before installing fixture.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code specifications. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
NOTE:
This instruction sheet covers both compact fluorescent and incandescent fixtures. Although illustration shows compact fluorescent, the incandescent version assembles and installs in the same manner.
NOTE:
The Backplate is provided with (3) Auxiliary Mounting Knockout Holes (4531, 4532, 4551, and 4552 series fixtures) for direct mounting to wall surfaces. These can be used for added security or where direct Outlet Box mounting is not available. To remove plug in Knockout Holes, follow steps 1 through 3 below.
For 4533 series fixtures, (4) Auxiliary Mounting Knockout Holes are provided for direct mounting to wall surfaces (no plugs to remove). It is recommended that Auxiliary Mounting Holes be used on 4532, 4533 and 4552 series fixtures.
The Backplate can be mounted horizontally of vertically. See Fig 1 below for proper orientation for type of Lens Assembly and desired position.
1.Position blunt ended punch or awl in center of Knockout hole and firmly hit with hammer to punch plug through. Repeat for remaining
Knockouts (Fig. 1).
Caution: Always wear eye protection (safety goggles) when removing Auxiliary Mounting Knock-Outs.
2.Position Backplate in desired position over Outlet Box and mark location of (4) Auxiliary Holes on wall surface.
3.Determine the appropriate mounting hardware required for type of wall material fixture is being mounted to (i.e. toggle bolts or molly screws for plaster or gysum board walls, wood screws, etc.)
4.Thread Crossbar Mounting Screws into Crossbar as shown in Fig. 1.
5.Using appropriate slots in Crossbar, secure Crossbar to Outlet Box using Outlet Box Screws (provided with Outlet Box).
6.While supporting Backplate make connections: black fixture lead or fixture without tracer marks to hot (black) supply lead; white fixture lead or fixture lead with tracer markers to neutral (white) supply lead. Un-insulated wire is a ground wire and must be connected to grounding terminals or ground lead inside Outlet Box. Use Wire Nuts (local hardware item). Push connections back into
Outlet Box.
Outlet Box |
|
Wire Nut |
||||||||
|
|
|
|
|
|
Ground Wire |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Position this edge |
of Backplate up |
for mounting of this |
Lens Assembly as shown |
Outlet Box Screws
Crossbar
Crossbar Mounting
Screws
Auxiliary Mounting
Knock-out
Mounting Hole
Position this edge 
of Backplate 
up for horizontal
mounting of this Lens Assembly
|
Backplate |
|
Gasket |
|
Safety Cable Loop |
|
Battery Nut |
|
Lens Assembly |
FIG.1 |
Mounting Screw |
|
LIGHTOLIER a GENLYTE company. |
|
631 Airport Road, Fall River, MA 02720 |
|
(508) 679-8131 • FAX (508) 647-4710 |
© 1995 |
Loading...