FIT SERIES
LAT/ROW
ASSEMBLY INSTRUCTIONS
Part # 7489801 |
1 |
Revision:5/06/03 |
Rev A. |
|
|
PARTS LIST
|
KEY |
PART # |
DESCRIPTION |
QTY |
1 |
ACU04-1656 |
TOWER |
1 |
|
2 |
ACU04-1654 |
FOOT PLATE |
1 |
|
3 |
ACU04-1652 |
LAT/LOW BOOM |
1 |
|
4 |
ACU04-1364 |
KNEE HOLD DOWN |
1 |
|
5 |
ACU04-1368 |
LAT/LOW SEAT |
1 |
|
6 |
ACU04-1363 |
LAT/LOW FRAME |
1 |
|
7 |
ACU04-1366 |
SWIVELPULLEY |
1 |
|
8 |
ACU02-1321 |
LAT/LOW PLATE |
4 |
|
9 |
ACU02-1320 |
LAT/LOWADJUST PLATE |
1 |
|
10 |
ACU04-1655 |
LAT/LOW BASE |
1 |
|
11 |
ACU02-1296 |
DUALPULLEYPLATE |
2 |
|
12 |
ACU04-1653 |
GUIDERODSUPPORT |
1 |
|
13 |
ACU06-0024 |
3-1/2”PULLEY |
1 |
|
14 |
ACU06-0025 |
4-1/2”PULLEY |
8 |
|
|
15 |
ACU02-1304 |
2-7/8 X 2-1/4” CABLE CLIP |
4 |
|
16 |
ACU05-0349 |
3/4 X 3-1/8” TAPPED SHAFT |
1 |
|
17 |
ACUDAEC03809016NB |
3/8 X 90mm BUTTON HEAD BOLT |
12 |
|
18 |
ACU06-0304 |
3/4 X 2”WEIGHTSTACK CUSHION |
2 |
|
19 |
ACU01-2375 |
GUIDEROD |
2 |
|
20 |
ACU72925 |
WEIGHT PLATE |
20 |
|
21 |
ACU06-0382 |
2-3/8” OD PLASTIC WASHER |
4 |
|
22 |
ACU10-0204ASY |
HEAD PLATE |
1 |
|
23 |
ACU11-0067 |
WEIGHT STACK PIN |
1 |
|
24 |
ACU05-0212 |
13/16” SHAFT COLLAR |
2 |
|
25 |
ACU06-0388 |
1-1/4” SHAFT COLLAR |
2 |
|
26 |
ACU05-0348 |
5-1/2” PIVOT SHAFT |
5 |
|
27 |
ACU07-0157 |
LAT SEAT PAD |
1 |
|
28 |
ACU10-0215 |
ROLLERPAD |
2 |
|
29 |
ACU08-0085 |
3/8 X 1/2” FLANGE SPACER |
8 |
30 |
ACU05-0350 |
3/8 X 1/2” SPACER |
1 |
|
|
|
|
|
|
KEY |
PART # |
DESCRIPTION |
QTY |
31 |
ACUDA1C03804316NU |
3/8 X 43mm BOLT |
5 |
32 |
ACUDA1C03805016NU |
3/8 X 50mm BOLT |
4 |
33 |
ACUDC1250100020B |
3/8” FLAT WASHER |
6 |
34 |
ACUDA1C03806716NU |
3/8 X 67mm BOLT |
4 |
35 |
ACUDA1C03807016NU |
3/8 X 70mm BOLT |
4 |
36 |
ACUDA1C03807316NU |
3/8 X 73mm BOLT |
4 |
37 |
ACUDA1C03809016NU |
3/8 X 90mm BOLT |
2 |
38 |
ACUDA1C03809716NU |
3/8 X 97mm BOLT |
2 |
39 |
ACUDA1C03816416NU |
3/8 X 164mm BOLT |
5 |
40 |
ACUDAEC03802516YB |
3/8X25mmBUTTONHEADBOLT |
2 |
41 |
ACU05-0313 |
1/2 X 3” SHOULDER BOLT |
1 |
42 |
ACUDC1250100020B |
3/8” BLACK FLAT WASHER |
26 |
43 |
ACUDB2E03807200U |
3/8” LOW HEIGHT LOCK NUT |
29 |
44 |
ACUDC1200105010U |
3/8” SAE WASHER |
53 |
45 |
ACU05-0310 |
3/8” RH WASHER |
53 |
46 |
ACU06-0357 |
BLACK RH CAP |
24 |
47 |
ACU06-0357 |
WHITE RH CAP |
29 |
OR |
ACU06-0357 |
PLATINUM RH CAP |
29 |
48 |
ACU13-0123 |
ROW CABLE |
1 |
49 |
ACU13-0166 |
LAT CABLE |
1 |
50 |
ACU73086 |
WEIGHTSTACK LABEL |
1 |
51 |
ACU05-0193 |
12 LINK CHAIN |
1 |
52 |
ACUDI1080080U |
SNAP LINK |
3 |
53 |
ACU04-1386 |
LAT BAR |
1 |
54 |
ACU04-0622 |
LOW ROW BAR |
1 |
55 |
ACU10-0229 |
TOP SHROUD |
1 |
56 |
ACU10-0231 |
FRONT SHROUD |
1 |
57 |
ACU10-0228 |
REAR SHROUD |
1 |
58 |
ACUDB9E03813016B |
3/8”ACORN NUT |
12 |
|
|
|
|
Tools Required for Assembly
*9/16” wrench
*Ratchet with 9/16” socket
*Metric Allen wrench set
2
313/8 X 43mm BOLT
323/8 X 50mm BOLT
34 3/8 X 67mm BOLT
35 3/8 X 70mm BOLT
36 3/8 X 73mm BOLT
58
3/8” ACORN NUT
37 3/8 X 90mm BOLT
38 3/8 X 97mm BOLT
39 3/8 X 164mm BOLT
43 3/8” LOW
HEIGHTLOCK
NUT
44 3/8” SAE WASHER
42 
3/8” BLACK
FLAT WASHER
46 47 RH CAP
(WHITE/PLATINUM/BLACK)
45 RH WASHER
3
40 3/8 X 25mm BUTTON HEAD BOLT
33
3/8” FLAT WASHER
17 3/8 X 90mm BUTTON HEAD BOLT
30
3/8 X 1/2” SPACER
41 1/2 X 3” SHOULDER BOLT
29 3/8 X 1/2”
FLANGESPACER
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OFTHE BOLT.
BOLT LENGTH
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0 |
1/2 |
|
1 |
1/2 |
2 |
1/2 |
3 |
|
1/2 |
4 |
1/2 |
|
|
5 |
1/2 |
6 |
|||||||||||||
10 |
|
20 |
30 |
40 |
50 |
60 |
|
70 |
|
80 |
90 |
100 |
|
110 |
|
120 |
130 |
140 |
150 |
|
|||||||||
|
|
|
|
|
|
|
|||||||||||||||||||||||
4
1
10
43
45 |
|
|
44 |
47 |
|
3/8 X 90mm 37 |
||
|
FIGURE 1
STEP 1:
•LOOSELY assemble the LAT/LOW BASE (10) to the TOWER (1) using four RH CAPS (47), two 3/8 X 90mm BOLTS (37), four 3/8” SAE WASHERS (44), four 3/8” RH WASHERS (45) and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 1.
5
43 |
34 3/8 X 67mm |
10 |
|
45 |
6 |
|
44 |
2 |
|
|
47 |
|
|
|
3/8 X 97mm 38 |
|
|
|
|
|
FIGURE 2
STEP 2:
•LOOSELY assemble the LAT/LOW FRAME (6) to the LAT/LOW BASE (10) using four RH CAPS (47), two 3/8 X 97mm BOLTS (38), four 3/8” SAE WASHERS (44), four 3/8” RH WASHERS (45) and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 2.
•LOOSELY assemble the FOOT PLATE (2) to the LAT/LOW FRAME (6) using four RH CAPS (47), two 3/8 X 67mm BOLTS (34), four 3/8” SAE WASHERS (44), four 3/8” RH WASHERS (45) and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 2.
6
Loading...