LG 20LS7DC, 23LS7D, 23LS7DC, 20LS7D User Manual

0 (0)

LCD TV

OWNER’S MANUAL

LCD TV MODELS

20LS7D

20LS7DC

23LS7D

23LS7DC

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer

when you require service.

ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).

As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

www.lgusa.com / www.lg.ca / www.lgcommercial.com

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE TO CABLE/TV INSTALLER

 

 

 

CAUTION

 

 

 

 

 

 

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

1

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.

The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may

be placed immediately adjacentw

ato that safety instruction :

n

 

ne

 

u

r

 

al

 

M

 

 

 

a

 

 

n

 

 

 

u

 

 

 

al

all warnings.

all instructions.

1

Ow n er

erM a n u al

5Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

2Clean only with dry cloth.

Do not block any ventilation openings. Install in

3accordance with the manufacturer’s instructions.

4Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

6Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

7Only use attachments/accessories specified by the manufacturer.

Ow n erM a n u al

2

8

 

 

 

 

authorized

 

 

 

from physical

 

 

 

 

with the apparatus. When a cart is used, use

or mechanical abuse, such as being twisted,

caution when moving the cart/apparatus

kinked, pinched, closed in a door, or walked

combination to avoid injury from tip-over.

upon. Pay particular attention to plugs, wall

 

 

 

outlets, and the point where the cord exits the

 

 

 

appliance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9Unplug this apparatus during lightning storms

10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

12 Outdoor use marking :

WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

13

Wet Location Marking : Apparatus shall not be

 

exposed to dripping or splashing and no

objects filled with liquids, such as vases, shall be placed on or over apparatus.

11 CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced

14 GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

15 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.

3

CONTENTS

WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Feature of this TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION

 

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. 7

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 8

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 9

Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10

Detaching Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . .

12

Positioning your display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Kensington Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . .

16

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Headphone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

- Auto Scan (EZ Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

- Add / Delete Channel (Manual Scan) . . . . . . . . . 33

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Input Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 37

Preset Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

- EZ Picture - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

- Color Tone - Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Manual Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

- EZ Picture - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

XD - Picture Improvement Technology . . . . . . . . . . . . . 43

Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 44

Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SOUND & LANGUAGE CONTROL

Preset Sound Setting (EZ Sound) . . . . . . . . . . . . . . . . . . . . . 46

Sound Setting Adjustment - User Mode . . . . . . . . . . . 47

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

On-Screen Menus Language Selection . . . . . . . . . . . . . . 51

Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

- Analog Broadcasting System Captions . . . . . . . 52

- Digital Broadcasting System Captions . . . . . . . . 53

Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4

TIME SETTING

Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

PARENTAL CONTROL / RATINGS

 

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . .

60

- Setting up Your Password . . . . . . . . . . . . . . . . . . . . . . . . .

60

- Set Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

- Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

- Movie Rating (MPAA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

- TV Rating Children & General (for USA only) . .

64

- TV Rating English & French (for Canada only) . .

65

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

External Control Through RS-232C . . . . . . . . . . . . . . . . . .70

5

INTRODUCTION

FEATURE OF THIS TV

LG's own special digital image generator, consisting of a full digital image processor, six different main picture quality factors.

High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.

Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.

HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

On Disposal

a.The fluorescent lamp used in this product contains a small amount of mercury.

b.Do not dispose of this product with general household waste.

c.Disposal of this product must be carried out in accordance to the regulations of your local authority.

6

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.

User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

7

5

3

 

 

 

 

 

-

 

 

 

 

 

 

 

CK

 

 

 

 

TV

POWER

 

 

 

 

SAP

BA

 

 

 

 

 

 

 

MU

 

 

 

 

P

 

 

 

 

 

 

ICT

 

TE

 

 

 

 

 

URE

IN

 

 

 

 

 

1

S

C

 

 

 

 

OUND

PUT

 

 

 

 

4

2

 

TIMER

EX

 

 

 

7

5

3

 

IT

 

 

 

 

 

 

 

 

-

8

6

 

 

 

 

 

0

9

 

 

 

 

 

VOL

BA

FAV

 

 

Owner's Manual

 

MEN

CK

 

 

 

 

 

M

 

 

 

 

 

 

 

UTE

 

 

 

 

 

U

CC

CH

 

 

 

 

 

 

AD

 

 

 

 

 

 

 

JUST

 

 

 

 

LCD TV

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

Owner's Manual

 

ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Owner’s Manual

CD Manual

Remote Control,

Power Cord

 

 

Batteries

 

*

Slightly wipe stained spot on the exterior only with the

 

polishing cloth for the product exterior if there is stain

 

or fingerprint on surface of the exterior.

*

Do not wipe roughly when removing stain. Please be

Cable Management

cautions of that excessive pressure may cause scratch

Polishing Cloth

or discoloration.

Option Extras

D-sub 15 pin Cable

PREPARATION

7

PREPARATION

PREPARATION

FRONT PANEL INFORMATION

Here shown may be somewhat different from your TV.

POWER

INPUT

MENU

ENTER

VOLUME

CHANNEL

Button

Button

Button

Button

(F,G)Buttons

(E,D)Buttons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/I

INPUT MENU ENTER

VOL

CH

Remote Control Sensor

Power Standby Indicator

Illuminates red in standby mode.

When the TV is turned on, the indicator blinks green and then illuminates green before the picture is displayed.

! NOTE

G If your TV stand has a protection film, remove it attached to the stand.

Then wipe the stand with polishing cloth.

8

BACK PANEL INFORMATION

Here shown may be somewhat different from your TV.

9

PREPARATION

 

 

 

 

 

 

4

 

 

2

HDMI/DVI IN

 

3

ANTENNA/

 

 

 

 

 

CABLE IN

 

 

 

AV IN

 

 

 

 

VIDEO

AUDIO

S-VIDEO

 

AUDIO IN

 

SERVICE

 

RGB (PC) IN

1

 

 

 

(RGB/DVI)

ONLY

 

 

 

 

 

L(MONO)

R

 

5

 

 

 

 

 

 

 

 

RS-232C IN

H/P

 

 

 

 

 

 

 

VIDEO

AUDIO

 

 

(CONTROL & SERVICE)

 

 

 

 

COMPONENT IN

 

 

 

 

 

 

 

8

7

 

 

6

 

1

2

Connect a HDMI signal to this jack.

Or DVI (Video) signal to this jack with a HDMI to

3AV IN (Audio/Video)

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

4ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

5(PC) IN

Connect the output from a PC.

AUDIO IN (RGB/DVI)

Connect the audio from a PC or DTV.

COMPONENT IN

Connect a component video/audio device to these jacks.

7HEADPHONE INPUT

Plug the headphone into the headphone socket.

8RS-232C IN (CONTROL & SERVICE) PORT

For external control devices.

9Power Cord Socket

For operation with AC power.

Caution: Never attempt to operate the TV on DC power.

9

PREPARATION

PREPARATION

STAND INSTALLATION

Here shown may be somewhat different from your TV.

1

of the stand. Insert the stand body into a cover base

 

stand body

cover base

2Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.

3Place the product stand on the product as shown.

10

LG 20LS7DC, 23LS7D, 23LS7DC, 20LS7D User Manual

DETACHING STAND

Here shown may be somewhat different from your TV.

1

a cushioned surface that will protect product and screen from damage.

2Pull cover base backward on stand body.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

4

Hold the stand and bend it upward.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PREPARATION

5Pull stand body to separate from set while pressing the 2 latches.

11

PREPARATION

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

Here shown may be somewhat different from your TV.

1

To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section.

2 Install the CABL

T as shown.

How to remove

MANAGEMENT

First, press the cable management. Hold the CABLE MANAGEMENT with both hands and pull it upward.

! NOTE

G Do not hold the CABLE MANAGEMENT when moving the product.

- If the product is dropped, you may be injured or the product may be broken.

12

POSITIONING YOUR DISPLAY

Here shown may be somewhat different from your TV.

Adjust the position of the panel in various ways for maximum comfort.

Tilt range

12~10

0

3

PREPARATION

13

PREPARATION

PREPARATION

VESA WALL MOUNTING

This product accepts a VESA-compliant mounting interface pad. (optional) There 4 threaded holes are available for attaching the bracket.

100 mm

100 mm

! NOTE

G Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide.

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4inches on all four sides from the wall.

4 inches

4 inches

 

4 inches

 

 

 

4

inches

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION G Ensure adequate ventilation by following the clearance recommendations.

14

KENSINGTON SECURITY SYSTEM

-The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.

-For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System.

For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.

NOTE

- The Kensington Security System is an optional accessory.

ATTACHING THE TV TO A DESK (Only 23 inches)

We recommend that the TV be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.

2-Bolts (M3x25)

(not provided as parts

Stand

 

of the product)

 

Desk

WARNING

G This apparatus must be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury/death.

PREPARATION

15

PREPARATION

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connections.

For optimum picture quality, adjust antenna direction if needed.

Multi-family Dwellings/Apartments

Wall (Connect to wall antenna socket)

Antenna

Socket

ANTENNA/

CABLE IN

Outdoor

RF Coaxial Wire (75 ohm)

 

Antenna

 

 

(VHF, UHF)

Single-family Dwellings /Houses

Copper Wire

 

(Connect to wall jack for outdoor antenna)

 

 

Be careful not to bend the bronze wire when connecting the antenna.

2. Cable

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

ANTENNA/ CABLE IN

3. Using both cable and antenna

Antenna

RF Coaxial Wire (75 ohm)

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

UHF

Antenna

Signal

Amplifier

 

 

VHF

Diplexer

(Signal

ANTENNA/

Combiner)

ANTENNA/CABLEIN

CABLE IN

ANTENNA/

CABLE IN

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

If the antenna is not installed properly, contact your dealer for assistance.

! NOTE G The TV will let you know when the analog, cable, and digital channel scans are complete.

16

EXTERNAL EQUIPMENT SETUP

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

When connecting Component cable

1. How to connect

 

Y

PR L R

1

Connect the video outputs (Y, PB, PR) of the digital set

 

 

top box to the COMPONENT IN VIDEO jacks on

 

the set. Match the jack colors

(Y = green, PB = blue, and PR = red).

box to

2.How to use

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box. operation)

Select Component input source by using the INPUT button on the remote control.

12

I/DVI IN

 

ANTENNA/

 

CABLE

 

 

AV

 

 

VIDEO

S-

 

 

AUDIO

IN

AUDIO IN

 

 

(RGB/DVI)

 

 

 

L(MONO)

 

 

H/P

 

 

 

)

VIDEO

AUDIO

 

 

COMPONENT IN

 

SETUP EQUIPMENT EXTERNAL

17

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

When connecting HDMI cable

1.How to connect

1 Connect the digital set-top box to HDMI/DVI IN jack on the set.

is necessary. and video.

2.to use

to the owner’s manual for the digital set-top box.)

HDMI/DVI input source by using the INPUT on the remote control.

! NOTE

G When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player output resolution will be automatically set to 720p.

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

HDMI/DVI IN

 

 

AV IN

VIDEO

AUDIO

S-VIDEO

 

SERVICE

 

 

 

ONLY

 

 

 

 

 

L(MONO)

R

1

H/P

 

RS-232C IN

 

 

 

(CONTROL & SERVICE)

 

 

VIDEO

 

 

 

COMP

HDMI-DTV OUTPUT

18

When connecting HDMI to DVI cable

HDMI/DVI IN

 

ANTENNA/

 

CABLE IN

 

AV IN

S-VIDEO

 

VIDEO

AUDIO

AUDIO IN

RGB (PC) IN

SERVICE

 

(RGB/DVI)

 

 

ONLY

 

 

 

L(MONO) R

 

 

1

H/P

 

IN

 

 

 

SERVICE)

VIDEO

AUDIO

 

COMPONENT IN

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVI-

OUTPUT

L

R

 

 

 

 

 

 

 

 

 

 

 

 

 

1. How to connect

1 Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the set.

the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the set.

2.How to use

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

Select HDMI/DVI input source by using the INPUT button on the remote control.

SETUP EQUIPMENT EXTERNAL

19

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

DVD SETUP

When connecting Component cable

1. How to connect

1

Connect the video outputs (Y, PB, PR) of the DVD to the

 

COMPONENT IN VIDEO jacks on the set.

PR L R

 

Y

 

Match the jack colors

 

 

(Y = green, PB = blue, and PR = red).

 

2. How to use

on the DVD player, insert a DVD.

Component input source by using the INPUT on the remote control.

to the DVD player's manual for operating instructions.

12

MI/DVI IN

 

ANTENNA/

 

CABLE

 

 

AV

 

 

VIDEO

S-

 

 

AUDIO

IN

AUDIO IN

 

 

(RGB/DVI)

 

 

 

L(MONO)

 

 

H/P

 

 

 

E)

VIDEO

AUDIO

 

 

COMPONENT IN

 

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

Y

PB

PR

 

 

 

 

 

 

 

 

 

Y

PB

PR

Video output ports

Y

B-Y

R-Y

on DVD player

Y

Cb

Cr

 

Y

Pb

Pr

 

 

 

 

20

When connecting with an S-Video cable

1. How to connect

Connect the S-VIDEO output of the DVD to the

1S -VIDEO input on the set.

2.How to use

on the DVD player, insert a DVD.

HDMI/DVI IN

 

ANTENNA/

 

CABLE IN

 

AV IN

S-VIDEO

 

VIDEO

AUDIO

AU

RGB (PC) IN

 

 

(RG

 

 

 

L

 

 

 

H/P

 

 

 

32C IN

 

 

 

& SERVICE)

 

AUDIO

 

 

 

COMPONENT IN

 

AV input source by using the INPUT button on the

 

 

 

control.

 

 

 

to the DVD player's manual for operating instructions.

L

R

S-VIDEO

 

 

 

When connecting HDMI cable

1.

How to connect

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Connect the HDMI output of the DVD to the

 

 

 

 

 

 

 

 

 

HDMI/DVI IN jack on the set.

 

 

 

 

 

 

 

 

 

HDMI supports both audio and video.

 

 

 

 

 

 

 

 

 

HDMI/DVI IN

 

 

 

 

2.

How to use

VIDEO

 

AV IN

 

 

AUDIO

 

 

 

 

 

 

 

 

 

S-VIDEO

 

 

SERVICE

 

 

 

ONLY

 

 

HDMI/DVI input source by using the INPUT

L(MONO)

R

 

on the remote control.

 

 

 

 

1

 

 

to the DVD player's manual for operating instructions.

H/P

 

 

RS-232C IN

 

 

 

(CONTROL & SERVICE)

VIDEO

 

 

 

CO

!

NOTE

 

 

G When connected, the TV will tell a connected device what

 

 

 

resolution it supports and the resolution it prefers. If the

 

 

 

device supports this Auto HDMI function, the player out-

HDMI-DVD OUTPUT

 

 

put resolution will be automatically set to 720p.

 

 

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the DVD to 720p.

SETUP EQUIPMENT EXTERNAL

21

EXTERNAL EQUIPMENT SETUP

VCR SETUP

SETUP EQUIPMENT EXTERNAL

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty

does not cover the product bearing this phenomenon.

When connecting with an antenna

 

 

1

 

 

 

 

 

 

OUT

VIDEO L

R S-VIDEO

 

 

ANTENNA/

IN

 

OUTPUT

HDMI/DVI IN

 

 

 

SWITCH

 

CABLE

 

 

 

AV IN

 

 

Wall Jack

 

VIDEO AUDIO

S-VIDEO

 

 

 

 

 

 

 

 

SERVICE

 

RGB (PC) IN

2

 

 

 

 

 

 

ONLY

 

 

 

 

 

L(MONO)

R

 

 

 

 

H/P

 

 

 

Antenna

 

 

 

 

 

 

RS-232C IN

 

 

 

 

 

(CONTROL & SERVICE)

VIDEO

AUDIO

 

 

 

 

COMPONENT IN

 

 

 

1. How to connect

1 Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the set.

the antenna cable to the RF antenna in socket of the VCR.

2.How to use

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

22

Loading...
+ 54 hidden pages