C540n, C543dn, C544n/dn/dw/dtn,
X546dtn MFP
Technical Reference
November 2010 |
www.lexmark.com |
|
|
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners.
© 2010 Lexmark International, Inc. All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550
Edition notice
November 2010
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
If you don't have access to the Internet, you can contact Lexmark by mail: Lexmark International, Inc.
Bldg 004-2/CSC
740 New Circle Road NW Lexington, KY 40550 USA
© 2010 Lexmark International, Inc. All rights reserved.
Trademarks
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. StapleSmart is a trademark of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands. All other trademarks are the property of their respective owners.
UNITED STATES GOVERNMENT RIGHTS
This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
Contents |
|
Edition notice............................................................................................... |
2 |
Introduction................................................................................................. |
5 |
Understanding letters after model numbers............................................................................................ |
5 |
Learning about the printer........................................................................... |
7 |
Finding information about the printer...................................................................................................... |
7 |
Printer Control Language (PCL) page formatting........................................... |
8 |
Printable areas.......................................................................................................................................... |
8 |
Supported paper and envelope dimensions............................................................................................. |
9 |
Printer Job Language (PJL).......................................................................... |
11 |
PJL commands information..................................................................................................................... |
11 |
PostScript (PS) emulation........................................................................... |
12 |
Paper sizes supported............................................................................................................................. |
12 |
PostScript paper tray support................................................................................................................. |
13 |
PostScript envelope size support............................................................................................................ |
14 |
PostScript envelope tray support............................................................................................................ |
15 |
Printer specifications.................................................................................. |
17 |
Airflow requirement................................................................................................................................ |
17 |
Noise emission levels.............................................................................................................................. |
17 |
Electrical specifications........................................................................................................................... |
18 |
Power requirements................................................................................................................................ |
18 |
Physical specifications............................................................................................................................. |
19 |
Clearance requirements.......................................................................................................................... |
20 |
Environmental conditions....................................................................................................................... |
20 |
Altitude specifications and atmospheric pressure.................................................................................. |
20 |
Appendix A: PCL support............................................................................ |
22 |
PCL emulation commands....................................................................................................................... |
22 |
GL/2 commands...................................................................................................................................... |
28 |
Contents
3
Appendix B: PJL support............................................................................. |
32 |
Common variables for both printer languages........................................................................................ |
32 |
Lexmark-unique PJL variables for both printer languages...................................................................... |
34 |
Common variables for PCL emulation..................................................................................................... |
41 |
Printer-unique variables for PCL emulation............................................................................................ |
41 |
Common variables for PostScript emulation........................................................................................... |
42 |
Printer-unique variables for PostScript emulation.................................................................................. |
42 |
Printer-unique LRESOURCE variables...................................................................................................... |
43 |
Status Readback commands.................................................................................................................... |
43 |
USTATUS unsolicited status variables..................................................................................................... |
43 |
PJL messages for auto-continuable conditions....................................................................................... |
44 |
PJL messages for attendance conditions................................................................................................. |
50 |
PJL messages for paper handling............................................................................................................. |
66 |
PJL messages for paper jams................................................................................................................... |
69 |
Service errors.......................................................................................................................................... |
76 |
Device attendance messages.................................................................................................................. |
76 |
Lexmark-unique PJL commands.............................................................................................................. |
76 |
File and device protection commands.................................................................................................... |
77 |
Appendix C: PostScript support.................................................................. |
79 |
Supplemental operators.......................................................................................................................... |
79 |
Page device parameters.......................................................................................................................... |
82 |
User interpreter parameters................................................................................................................... |
86 |
System interpreter parameters............................................................................................................... |
87 |
Devices supported................................................................................................................................... |
90 |
Device parameters.................................................................................................................................. |
92 |
PostScript message keys commands..................................................................................................... |
101 |
Index........................................................................................................ |
102 |
Contents
4
Overview
This edition of the Technical Reference contains information about the following printers or multifunction printers (MFPs):
C540n
C543dn
C544n
C544dn
C544dw
C544dtn
X546dtn
Some Lexmark printers may have one or more letters after the model name to indicate printer features:
|
Acronym |
Meaning |
|
d |
duplex1 |
|
de |
duplex and e-Task (electronic task) touch-screen interface |
|
|
|
|
dfe |
duplex, finisher/stapler, and e-Task touch-screen interface |
|
|
|
|
dhe |
duplex, high-capacity drawer, and e-Task touch-screen interface |
|
|
|
|
dhn |
duplex, high-capacity drawer, and network |
|
|
|
|
dme |
duplex, mailbox, and e-Task touch-screen interface |
|
|
|
|
dn |
duplex and network |
|
|
|
|
dnf |
duplex, network, and finisher/stapler |
|
|
|
|
dnw or dw |
duplex, network, and wireless |
|
|
|
|
dt |
duplex and additional tray2 |
|
dte |
duplex, additional tray, and e-Task touch-screen interface |
|
|
|
|
dtn |
duplex, additional tray, and network |
|
|
|
|
dttn |
duplex, tandem tray module, and network |
|
|
|
|
dtwe |
duplex, additional tray, wireless, and e-Task touch-screen interface |
|
|
|
|
e |
e-Task touch-screen interface |
|
|
|
|
hdn |
hard disk, duplex, and network |
|
|
|
1Duplex printing (two-sided printing) accomplished by means of an optional duplex unit or an internal duplex unit based on the product.
2The additional tray is part of a drawer.
Introduction
5
|
Acronym |
Meaning |
|
n |
network |
|
|
|
|
nl |
network light model |
|
|
|
|
ni |
network and ImageQuick |
|
|
|
|
tn |
network and additional tray |
|
|
|
1Duplex printing (two-sided printing) accomplished by means of an optional duplex unit or an internal duplex unit based on the product.
2The additional tray is part of a drawer.
Introduction
6
Learning about theprinter
Setup information
Description |
Where to find |
The Setup information gives you instructions for setting |
You can find the Setup information on the inside of the printer |
up the printer. Follow the set of instructions for local, |
box or on the Lexmark Web site at www.lexmark.com. |
network, or wireless, depending on what you need. |
|
|
|
Help
Description |
Where to find |
|
|
The Help gives you instructions for using the software. While in any Lexmark software program, click Help, Tips Help, or Help Help Topics.
Customer support
|
Description |
Where to find (North America) |
Where to find (rest of world) |
|
|
Telephone support |
Call us at |
Telephone numbers and support hours vary by |
|
|
|
• |
US: 1-800-332-4120 |
country or region. |
|
|
|
Monday–Friday (8:00 AM–11:00 PM ET) |
Visit our Web site at www.lexmark.com. Select |
|
|
|
a country or region, and then select the Customer |
|
|
|
|
Saturday (Noon–6:00 PM ET) |
|
|
|
|
Support link. |
|
|
|
• |
Canada: 1-800-539-6275 |
|
|
|
Note: For additional information about |
||
|
|
|
Monday–Friday (8:00 AM–11:00 PM ET) |
|
|
|
|
contacting Lexmark, see the printed warranty |
|
|
|
|
Saturday (Noon–6:00 PM ET) |
|
|
|
|
that came with your printer. |
|
|
|
• |
Mexico: 001-888-377-0063 |
|
|
|
|
Monday–Friday (8:00 AM–8:00 PM ET) |
|
|
|
Note: Telephone numbers and support times may |
|
|
|
|
change without notice. For the most recent |
|
|
|
|
telephone numbers available, see the printed |
|
|
|
|
warranty statement that came with your printer. |
|
|
|
|
|
|
|
|
E-mail support |
For e-mail support, visit our Web site: |
E-mail support varies by country or region, and |
|
|
|
www.lexmark.com. |
may not be available in some instances. |
|
|
|
1 Click SUPPORT. |
Visit our Web site at www.lexmark.com. Select |
|
|
|
2 Click Technical Support. |
a country or region, and then select the Customer |
|
|
|
3 Select your printer type. |
Support link. |
|
|
|
Note: For additional information about |
||
|
|
4 Select your printer model. |
||
|
|
contacting Lexmark, see the printed warranty |
||
|
|
5 From the Support Tools section, click e-Mail |
||
|
|
that came with your printer. |
||
|
|
|
Support. |
|
|
|
|
|
|
|
|
6 Complete the form, and then click Submit |
|
|
|
|
|
Request. |
|
|
|
|
|
|
7
PrinterControl Language(PCL) page formatting
For more information on PCL, refer to the Printer Languages and Interfaces Technical Reference. It contains a complete listing with descriptions of PCL commands.
To determine which PCL commands your printer supports, see “Appendix A: PCL support” on page 22.
The printable areas and logical pages for PCL emulation (both portrait and landscape orientation) are illustrated below. See the legend that follows for definitions of areas A through I.
Legend:
APortrait physical page width and landscape physical page length
BPortrait physical page length and landscape physical page width
CPortrait logical page width
DLandscape logical page width
EDistance between the side edge of the physical page and the logical page in portrait
FDistance between the side edge of the physical page and the logical page in landscape
GDistance between the top and bottom edge of the physical page and logical page
HDistance between the left and right edge of the physical page and the printable area in portrait, or distance between the top and bottom edge of the physical page and printable area in landscape
IDistance between the top and bottom edge of the physical page and the printable area in portrait, or distance between the left and right edge of the physical page and the printable area in landscape
Note: The tables that follow in this chapter list the page sizes and dimensions of each area labeled on the preceding diagram for all paper and envelope sizes your printer supports.
8
The following table lists the page sizes and print area dimensions for all supported paper and envelope sizes. For more information about the printable areas and logical pages for PCL emulation, see “Printable areas” on page 8.
|
Selection |
|
Paper/envelope |
Dimensions by area (pels)1 |
|
|
|
|
|
|
||||
|
|
|
dimensions |
|
|
|
|
|
|
|
|
|
|
|
|
Page size |
Name |
mm |
inches |
A |
|
B |
C |
D |
E |
F |
G |
H |
I |
|
parameters2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Paper |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2,602 |
Letter |
216 x |
8.5 x 11 |
5100 |
|
6600 |
4800 |
6360 |
150 |
120 |
0 |
200 |
200 |
|
|
|
279 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3,603 |
Legal |
216 x |
8.5 x 14 |
5100 |
|
8400 |
4800 |
8160 |
150 |
120 |
0 |
200 |
200 |
|
|
|
356 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12,45,612 |
JIS B5 |
182 x |
7.2 x 10.1 |
4300 |
|
6070 |
4000 |
5830 |
150 |
120 |
0 |
200 |
200 |
|
|
|
257 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
26,626 |
A4 (198 |
210 x |
8.3 x 11.7 |
4960 |
|
7014 |
4676 |
6778 |
142 |
118 |
0 |
160 |
200 |
|
|
mm)3 |
297 |
|
|
|
|
|
|
|
|
|
|
|
|
26,626 |
A4 (203 |
210 x |
8.3 x 11.7 |
4960 |
|
7014 |
4676 |
6778 |
80 |
118 |
0 |
160 |
200 |
|
|
mm)3 |
297 |
|
|
|
|
|
|
|
|
|
|
|
|
1,601 |
Exec |
184 x |
7.25 x 10.5 |
4350 |
|
6300 |
4050 |
6060 |
150 |
120 |
0 |
200 |
200 |
|
|
|
267 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13,613 |
A5 |
148 x |
5.83 x 8.27 |
3496 |
|
4960 |
3196 |
4720 |
142 |
118 |
0 |
200 |
200 |
|
|
|
210 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
300 |
Oficio |
216 x |
8.5 x 13.4 |
5100 |
|
8040 |
4800 |
7800 |
150 |
120 |
0 |
200 |
200 |
|
|
(Mexico) |
340 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 or 10 |
Folio |
216 x |
8.5 x 13 |
5100 |
|
7800 |
4800 |
7560 |
150 |
120 |
0 |
200 |
200 |
|
|
|
330 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
101 |
Universal |
216 x |
8.5 x 14 |
1800- |
|
1800- |
1500- |
1500- |
75 |
60 |
0 |
100 |
100 |
|
|
|
356 |
|
51004 |
|
85024 |
48004 |
82024 |
|
|
|
|
|
|
|
|
|
|
Envelope |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
90 |
DL |
220 x |
8.66 x 4.33 |
2598 |
|
5196 |
2314 |
4960 |
142 |
118 |
0 |
200 |
200 |
|
|
|
110 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1Pel dimensions are for 600 dpi.
2Page Size Parameters are explained in the Page Control table in the PCL chapter in the Printer Language and Interfaces Technical Reference.
3The width of the logical page for A4 paper can be changed from the printer control panel or your software application.
4For the Universal paper size, the area dimensions are listed in pel ranges.
5Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter in the Printer Language and Interfaces Technical Reference.
Printer Control Language (PCL) page formatting
9
|
Selection |
|
Paper/envelope |
Dimensions by area (pels)1 |
|
|
|
|
|
|
|||
|
|
|
dimensions |
|
|
|
|
|
|
|
|
|
|
|
Page size |
Name |
mm |
inches |
A |
B |
C |
D |
E |
F |
G |
H |
I |
|
parameters2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
91 |
C5 |
229 x |
9.02 x 6.38 |
3826 |
5408 |
3542 |
5172 |
142 |
118 |
0 |
200 |
200 |
|
|
|
162 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
99d, 100 |
B5 Envelope |
250 x |
9.84 x 6.93 |
4156 |
5904 |
3872 |
5668 |
142 |
118 |
0 |
200 |
200 |
|
|
|
176 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
600 |
Other |
229 x |
9 x 14 |
5100 |
8400 |
4800 |
8160 |
|
|
0 |
200 |
200 |
|
|
Envelope |
356 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
89 |
9 (Com 9) |
98 x 225 |
8.875 |
2324 |
5324 |
2024 |
5084 |
150 |
120 |
0 |
200 |
200 |
|
|
|
|
x3.875 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
81 |
10 (Com 10) |
241 x |
9.5 x 4.125 |
2474 |
5700 |
2174 |
5460 |
150 |
120 |
0 |
200 |
200 |
|
|
|
105 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
80 |
7 3/4 |
98 x 191 |
3.875 x7.5 |
2324 |
4500 |
2024 |
4260 |
150 |
120 |
0 |
200 |
200 |
|
|
(Monarch) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1Pel dimensions are for 600 dpi.
2Page Size Parameters are explained in the Page Control table in the PCL chapter in the Printer Language and Interfaces Technical Reference.
3The width of the logical page for A4 paper can be changed from the printer control panel or your software application.
4For the Universal paper size, the area dimensions are listed in pel ranges.
5Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter in the Printer Language and Interfaces Technical Reference.
Printer Control Language (PCL) page formatting
10
PrinterJob Language(PJL)
Your printer supports complete PJL commands, including certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS).
For a complete listing with descriptions of PJL commands, see the Printer Languages and Interfaces Technical Reference.
To determine which commands your printer supports, see “Appendix B: PJL support” on page 32.
11
PostScript(PS)emulation
Your printer supports complete PostScript emulation supplemental operators. For full descriptions in detail for these operators, refer to the PostScript emulation chapter in the Printer Languages and Interfaces Technical Reference.
To determine which commands your printer supports, see “Appendix C: PostScript support” on page 79.
= Supported |
|
|
|
|
|
|
X = Not supported |
|
|
|
|
|
|
Paper sizes |
|
|
|
|
Printer models |
|
Size |
Literal name |
Size (mm) |
Size (inches) |
Size (points) |
C540n, C543dn, |
X546dtn MFP |
|
|
|
|
|
C544n/dn/dw/dtn |
|
Letter |
letter |
215.9 x 279.4 |
8.5 x 11.0 |
612 x 792 |
|
|
Legal |
legal |
215.9 x 355.6 |
8.5 x 14.0 |
612 x 1008 |
|
|
JIS B5 |
b5* |
182.0 x 257.0 |
7.2 x 10.1 |
516 x 729 |
|
|
A4 |
a4 |
210.0 x 297.0 |
8.3 x 11.7 |
595 x 842 |
|
|
Executive |
executive |
184.2 x 266.7 |
7.25 x 10.5 |
522 x 756 |
|
|
|
page |
|
|
|
|
|
A5 |
a5 |
148.0 x 210.0 |
5.83 x 8.27 |
419 x 595 |
|
|
11 x 17 |
ledger |
431.8 x 279.4 |
17 x 11 |
1224 x 792 |
X |
X |
Oficio |
oficio |
215.9 x 340.4 |
8.5 x 13.4 |
612 x 965 |
|
|
|
|
|
|
(Lexmark |
|
|
|
|
|
|
unique size) |
|
|
|
|
|
|
612 x 972 |
|
|
|
|
|
|
(official |
|
|
|
|
|
|
PostScript |
|
|
|
|
|
|
size) |
|
|
Folio |
folio |
215.9 x 330.2 |
8.5 x 13.0 |
612 x 936 |
|
|
Universal |
universal |
216 x 356 |
8.5 x 14 |
612 x 1008 |
|
|
* This is a Japanese Industry Standard (JIS) paper size. The same named designation is used by JIS and International Standards Organization (ISO) for different paper sizes.
12
When the printer receives one of the operators listed in “Tray selected with tray operators” on page 13, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray.
•The printer checks the value of manualfeed in statusdict and the ManualFeed page device parameter. If either one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder.
•The PageSize Policy is set to 0 by means of setpagedevice.
•The printer checks the paper size loaded in the current active source to determine if it matches the requested size. If the sizes match, the paper is fed from the active source.
Note: The current active tray is the last source that was selected from the printer control panel or by the printer language.
•If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
•If the requested media size is not found by the previous search, the following search order is used:
–Tray 1
–Optional 650-sheet duo drawer (Tray 2)
–Optional 550-sheet tray (Tray 3)
–Multipurpose feeder
•If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed.
For printers that support automatic duplexing:
•Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder. Automatic duplexing is supported from the multipurpose feeder for all other papers.
•If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper source changes, and the information for the back side of the page is printed on the front side of a page sent from the new paper source.
When these operators are used, it is equivalent to executing the following PostScript emulation sequence:
<< /PageSize [x y]/ImagingBBox null /Policies << /PageSize 0>> >>
setpagedevice
where x y are the PageSize in points.
Tray selected with tray operators
|
= Supported |
|
|
|
|
X = Not supported |
Printer models |
|
|
|
Operator |
Tray selected (corresponding image size is set) |
C540n, C543dn, C544n/dn/dw/dtn |
X546dtn MFP |
|
a4tray |
tray with A4-size paper |
|
|
|
|
|
|
|
|
a5tray |
tray with A5-size paper |
|
|
|
|
|
|
|
|
b5tray |
tray with B5-size paper |
|
|
|
|
|
|
|
|
customtray |
tray with custom-size paper |
X |
X |
|
|
|
|
|
|
executivetray |
tray with executive-size paper |
|
|
|
|
|
|
|
PostScript (PS) emulation
13
|
= Supported |
|
|
|
|
X = Not supported |
Printer models |
|
|
|
Operator |
Tray selected (corresponding image size is set) |
C540n, C543dn, C544n/dn/dw/dtn |
X546dtn MFP |
|
foliotray |
tray with folio-size paper |
|
|
|
|
|
|
|
|
ledgertray |
tray with 279.4 x 431.8-mm (11 x 17-in.) paper with |
X |
X |
|
|
landscape orientation |
|
|
|
|
|
|
|
|
legaltray |
tray with legal-size paper |
|
|
|
|
|
|
|
|
lettertray |
tray with letter-size paper |
|
|
|
|
|
|
|
|
oficiotray |
tray with oficio-size paper |
|
|
|
|
|
|
|
The literal names in “Envelope sizes supported” on page 14 are also supported as operators in userdict. These operators change the image size, but do not change the active paper source. Therefore, when these operators are used, part of the image may be clipped.
When these literal names are used as operators, it is equivalent to executing the following PostScript emulation sequence. The following example uses a 3.875 x 7.5 envelope.
<</Policies <</PageSize 7>> /PageSize [279 540]>> >>setpagedevice
Envelope sizes supported
= Supported |
|
|
|
|
|
|
X = Not supported |
|
|
|
|
|
|
Envelope sizes |
|
|
|
|
Printer models |
|
Size name |
Literal name |
Size (mm) |
Size (inches) |
Size (points) |
C540n, C543dn, |
X546dtn MFP |
|
|
|
|
|
C544n/dn/dw |
|
|
|
|
|
|
/dtn |
|
7 3/4 |
3.875x7.5envel |
98.4 x 190.5 |
3.875 x 7.5 |
279 x 540 |
|
|
|
ope |
|
|
|
|
|
Commercial 9 |
3.875x8.875env |
98.4 x 225.4 |
3.875 x 8.875 |
279 x 639 |
|
|
|
elope |
|
|
|
|
|
Commercial 10 |
4.125x9.5envel |
104.8 x 241.3 |
4.125 x 9.5 |
297 x 684 |
|
|
|
ope |
|
|
|
|
|
International DL |
110x220envelo |
110 x 220 |
4.33 x 8.66 |
312 x 624 |
|
|
|
pe |
|
|
|
|
|
International C5 |
162x229envelo |
162 x 229 |
6.38 x 9.01 |
459 x 649 |
|
|
|
pe |
|
|
|
|
|
International B5 |
176x250envelo |
176 x 250 |
6.93 x 9.84 |
499 x 708 |
|
|
|
pe |
|
|
|
|
|
Other envelope |
otherenvelope |
229.11 x 355.6 |
9.02 x 14 |
612 x 996 |
|
|
PostScript (PS) emulation
14
|
= Supported |
|
|
|
|
|
|
|
X = Not supported |
|
|
|
|
|
|
|
Envelope sizes |
|
|
|
|
Printer models |
|
|
Size name |
Literal name |
Size (mm) |
Size (inches) |
Size (points) |
C540n, C543dn, |
X546dtn MFP |
|
|
|
|
|
|
C544n/dn/dw |
|
|
|
|
|
|
|
/dtn |
|
|
otherenvelope |
Other |
296.93 x 427.48 |
11.69 x 16.83 |
841 x 842 |
X |
X |
|
|
|
|
|
|
|
|
Literal names supported
= Supported |
|
X = Not Supported |
|
Literal names |
Printer models |
Literal name |
Compatible literal name |
C540n, C543dn, C544n/dn/dw/dtn |
X546dtn MFP |
monarchenvelope |
3.875x7.5envelope |
|
|
com10envelope |
4.125x9.5envelope |
|
|
dlenvelope |
110x220envelope |
|
|
c5envelope |
162x229envelope |
|
|
b5envelope |
176x250envelope |
|
|
If manualfeed in statusdict and the ManualFeed page device parameter are false when the printer receives one of the envelopetray operators listed in “Envelopetray operator selections” on page 16, then the printer:
•Sets the PageSize Policy to 0.
•Checks the active source to see if it matches the requested envelope size. If the sizes match, the envelope is fed from the active source.
Note: The active source is the last source selected from the printer control panel or data stream.
•If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
•If the requested media size is not found by the previous search, the following search order is used:
–Envelope Feeder
–Multipurpose Feeder
•If the requested size and type are not available from any automatic source, you are prompted to load the requested envelope size and type in the manual feed source.
•If the size is still not available, a configurationerror is issued and the print job is flushed.
If manualfeed or ManualFeed is true, the printer prompts you to load the requested size manually. If no manual feed exists on the printer, a rangecheck error message is generated
PostScript (PS) emulation
15
The envelope tray the printer selects when it receives an envelopetray operator is listed in “Envelopetray operator selections” on page 16. These operators are equivalent to executing the following PostScript emulation sequence:
<</PageSize [x y] /ImagingBBox null /Policies<</PageSize 0>> >> setpagedevice
where x y are the PageSize in points.
Envelopetray operator selections
|
= Supported |
|
|
|
|
X = Not supported |
|
|
|
|
Tray operators |
|
Printer models |
|
|
Operator |
Tray selected (Corresponding image size is |
C540n, C543dn, C544n/dn/dw/dtn |
X546dtn MFP |
|
|
set) |
|
|
|
110x220envelopetray |
tray with 110 x 220 size envelopes |
|
|
|
|
|
|
|
|
dlenvelopetray |
tray with 110 x 220 size envelopes |
|
|
|
|
|
|
|
|
162x229envelopetray |
tray with 162 x 229 size envelopes |
|
|
|
|
|
|
|
|
c5envelopetray |
tray with 162 x 229 size envelopes |
|
|
|
|
|
|
|
|
176x250envelopetray |
tray with 176 x 250 size envelopes |
|
|
|
|
|
|
|
|
b5envelopetray |
tray with 176 x 250 size envelopes |
|
|
|
|
|
|
|
|
3.875x7.5envelopetray |
tray with 3.875 x 7.5 size envelopes |
|
|
|
|
|
|
|
|
monarcenvelopetray |
tray with 3.875 x 7.5 size envelopes |
|
|
|
|
|
|
|
|
3.875x8.875envelopetray |
tray with 3.875 x 8.875 size envelopes |
|
|
|
|
|
|
|
|
4.125x9.5envelopetray |
tray with 4.125 x 9.5 size envelopes |
|
|
|
|
|
|
|
|
com10envelopetray |
tray with 4.125 x 9.5 size envelopes |
|
|
|
|
|
|
|
|
otherenvelopetray |
tray with other size envelopes |
|
|
|
|
|
|
|
PostScript (PS) emulation
16
Printerspecifications
This chapter lists printer specifications and information about hardware, environmental conditions, and power requirements.
The room should meet ASHRAE 62—1989 standards.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
C54x Color Laser Series
|
|
|
|
1-meter average sound pressure, dBA |
||
|
|
|
|
|
|
|
|
Status |
C540n |
C543dn |
|
C544n |
C544dn, C544dw, C544dtn |
|
Printing (Simplex) |
47 |
47 |
|
49 |
49 |
|
|
|
|
|
|
|
|
Printing (Auto duplex) |
Inapplicable |
50 |
|
Inapplicable |
51 |
|
|
|
|
|
|
|
|
Standby (Idle without |
Inaudible |
Inaudible |
|
Inaudible |
Inaudible |
|
Power Saver) |
|
|
|
|
|
|
|
|
|
|
|
|
|
Quiet Mode (Simplex) |
46 |
46 |
|
46 |
46 |
|
|
|
|
|
|
|
|
Note: Measurements apply to 300-dpi, 600-dpi, and 1200-dpi printing. |
|
||||
|
|
|
|
|
|
|
X546dtn MFP
Status |
1-meter average sound pressure, dBA |
Declared sound power levels, Bels |
Printing (Simplex Mono) |
47 |
6.2 |
|
|
|
Printing (Simplex Color) |
48 |
6.3 |
|
|
|
Printing (Duplex Mono) |
50 |
6.5 |
|
|
|
Printing (Duplex Color) |
51 |
6.5 |
|
|
|
Copy (ADF Mono) |
49 |
6.4 |
|
|
|
Copy (ADF Color) |
50 |
6.5 |
|
|
|
Scan (ADF Mono) |
45 |
6.1 |
|
|
|
Scan (ADF Color) |
45 |
6.1 |
|
|
|
Standby (Idle without Power Saver) |
Inaudible |
Inaudible |
|
|
|
Quiet Mode (Simplex Mono) |
45 |
5.9 |
|
|
|
Quiet Mode (Simplex Color) |
45 |
6.0 |
Note: Measurements apply to 300-dpi, 600-dpi, and 1200-dpi printing.
17
Printer model |
Electrical specification |
C54x low voltage models* |
100–127 V at 47–63 Hz, nominal |
|
90–137 V, extreme |
|
|
C54x 100 volt model |
100 V at 47–63 Hz, nominal |
|
90–110 V, extreme |
|
|
C54x high voltage models |
220–240 V at 47–63 Hz (not available in all countries) |
|
198–259 V, extreme |
|
|
X546dtn MFP low voltage models |
100–110 V (Japan) at 50–60 Hz, nominal |
|
100–127 V at 50–60 Hz, nominal |
|
90–110 V (Japan), extreme |
|
90–137 V, extreme |
|
|
X546dtn MFP high voltage models |
220–240 V at 50–60 Hz, nominal (not available in all countries) |
|
198–264 V, extreme |
* Using a 220–110 power converter with 110 V printer is not recommended.
Warning—Potential Damage: Lexmark recommends that you do not use voltage converters with printers.
The following tables list the nominal average power requirements (including fuser power).
Lexmark C54x nominal average power requirements
Printing states |
C540n, C543dn |
C544n, C544dn, C544dw, C544dtn |
Average power while printing continuously |
|
|
|
|
|
1-sided (simplex) |
480 W |
500 W |
2-sided (duplex) |
340 W |
340 W |
|
|
|
Average power while idle |
|
|
|
|
|
Power Saver on |
18 W |
18 W |
Ready mode |
34 W |
36 W |
|
|
|
Max current while printing |
|
|
|
|
|
100–110 V |
8.7 A |
8.7 A |
110–127 V |
7.6 A |
7.6 A |
220–240 V |
4.1 A |
4.1 A |
Note: Automatic duplex is not supported on the C540n and C544n.
Printer specifications
18
Lexmark X546dtn MFP nominal average power requirements
|
Printing states |
X546dtn |
|
Printing continuously (simplex) |
540 W |
|
|
|
|
Printing continuously (duplex) |
370 W |
|
|
|
|
Copying continuously |
510 W |
|
|
|
|
Scanning |
60 W |
|
|
|
|
Average power while idle |
|
|
|
|
|
Power Saver Mode/Sleep Mode |
23 W |
|
Standby Mode |
50 W |
|
|
|
|
Max (Average) current while printing |
|
|
|
|
|
100--110 V |
8.1 A |
|
115--127 V |
7.0 A |
|
220--240 V |
3.6 A |
|
|
|
Lexmark C54x dimensions
|
|
Height |
Width |
Depth |
Weight |
|
C540n |
291.2 mm (11.5 in.) |
423.9 mm (16.7 in.) |
399.7 mm (15.7 in.) |
21 kg (46.2 lb) |
|
C543dn |
|
|
|
|
|
C544n |
|
|
|
|
|
C544dn |
|
|
|
|
|
C544dw |
|
|
|
|
|
|
|
|
|
|
|
C544dtn |
422.3 mm (16.6 in.) |
423.9 mm (16.7 in.) |
416.4 mm (16.4 in.) |
25 kg (54.9 lb) |
|
C544dtn with optional 650-sheet duo |
|
|
|
|
|
drawer |
|
|
|
|
|
|
|
|
|
|
Input option for Lexmark C54x Models
Option name |
Height |
Width |
Depth |
Weight |
650-sheet duo drawer |
133 mm (5.2 in.) |
423.9 mm (16.7 in.) |
416.4 mm (16.4 in.) |
4 kg (8.7 lb) |
|
|
|
|
|
Lexmark X546dtn MFP dimensions
|
|
Height |
Width |
Depth |
Weight |
|
X546dtn |
569 mm (23.5 in.) |
440 mm (17.32 in.) |
537 mm (21.14 in.) |
31.37 kg (69.15 lb) |
|
|
|
|
|
|
|
X546dtn with optional 650-sheet duo |
133 mm (5.2 in.) |
423.9 mm (16.7 in.) |
416.4 mm (16.4 in.) |
4.16 kg (9.15 lb) |
|
drawer |
|
|
|
|
|
|
|
|
|
|
|
X546dtn with optional 550-sheet drawer |
133 mm (5.2 in.) |
423.9 mm (16.6 in.) |
416.4 mm (16.4 in.) |
4.16 kg (9.15 lb) |
|
|
|
|
|
|
Printer specifications
19
Lexmark C540n, C543dn, C544n/dn/dw/dtn
Model |
Left side |
Right side |
Front |
Rear |
Top |
C540n, C543dn, C544n, C544dn, |
76.2 mm (3 in.) |
152.4 mm (6 in.) |
508 mm (20 in.) |
101.6 mm (4 in.) |
254 mm (10 in.) |
C544dw |
|
|
|
|
|
|
|
|
|
|
|
C544dtn |
76.2 mm (3 in.) |
254 mm (10 in.) |
508 mm (20 in.) |
101.6 mm (4 in.) |
254 mm (10 in.) |
Note: Allow an additional 133 mm (5.2 in.) clearance above the C54x for an optional drawer.
Lexmark X546dtn MFP
Model |
Left side |
Right side |
Front |
Rear |
Top |
X546dtn |
76.2 mm (3 in.) |
254 mm (10 in.) |
508 mm (20 in.) |
101.6 mm (4 in.) |
360 mm (14 in.) |
Note: Allow an additional 133 mm (5.2 in.) clearance above the X546dtn for an optional input drawer.
Note: When shipping or storing printers, always pack the printer supplies (cartridges and photoconductors, for example) separately.
Air temperature ranges
|
Printer model |
Operating value |
Shipping value |
Storage (unpacked) |
|
C540n, C543dn, C544n/dn/dw/dtn |
15.6–32.2°C (60–90°F) |
-40–43.3°C (-40–110°F) |
0–40°C (32–104°F) |
|
|
|
|
|
|
X546dtn MFP |
15.6–32.2°C (60–90°F) |
-40–43.3°C (-40–110°F) |
0–40°C (32–104°F) |
|
|
|
|
|
Humidity ranges
Printer model |
Operating value |
Shipping value |
Storage value |
C540n, C543dn, C544n/dn/dw/dtn |
8%–80%* |
8%–80% |
8%–80% |
|
|
|
|
X546dtn MFP |
8%–80%* |
8%–80% |
8%–80% |
* Approaching 32°C (90°F) the maximum relative humidity is 60%.
Altitude specifications
|
|
Altitude (above sea level) |
|
|
|
||
|
Printer model |
Operating |
Shipping/storage |
|
C540n, C543dn, C544n/dn/dw/dtn |
0–3048 M (10,000 ft.) |
10,300 M (34,000 ft.) |
|
|
|
|
|
XC546dtn MFP |
0–3048 M (10,000 ft.) |
10,300 M (34,000 ft.) |
|
|
|
|
Printer specifications
20
Atmospheric Pressure
74.6 kPa
Printer specifications
21
Appendix A:PCL support
= Supported |
|
|
|
X = Not supported |
|
Printer model |
|
|
|
C540n, C543dn, C544n, |
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
Decimal 8 |
BS, Backspace |
|
|
Decimal 9 |
HT, Horizontal Tab |
|
|
Decimal 10 |
LF, Line Feed |
|
|
Decimal 12 |
FF, Form Feed |
|
|
Decimal 13 |
CR, Carrier Return |
|
|
Decimal 14 |
SO, Select Secondary Font |
|
|
Decimal 15 |
SI, Select Primary Font |
|
|
Decimal 32 |
SP, Space |
|
|
ESCE |
Printer Reset |
|
|
ESCY |
Display Functions-On |
|
|
ESCZ |
Display Functions-Off |
|
|
ESCz |
Print Test Page |
X |
X |
ESC&a#C |
Horizontal Cursor Position |
|
|
|
(in Columns) |
|
|
ESC&a#G |
Duplex Page Side Selection |
|
|
ESC&a#H |
Horizontal Cursor Position |
|
|
|
(in Decipoints) |
|
|
ESC&a#L |
Set Left Margin |
|
|
ESC&a#M |
Set Right Margin |
|
|
ESC&a#N |
Negative Motion |
X |
X |
ESC&a#P |
Print Direction |
|
|
ESC&a#R |
Vertical Cursor Position (in Rows) |
|
|
ESC&a#V |
Vertical Cursor Position |
|
|
|
(in Decipoints) |
|
|
22
|
= Supported |
|
|
|
X = Not supported |
|
Printer model |
||
|
|
|
C540n, C543dn, C544n, |
|
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
|
ESC&b#M |
Monochrome Print Mode |
|
|
|
ESC&b#W[data] |
Configuration Command |
X |
X |
|
ESC&c#T |
Character Text Path Direction |
|
|
|
ESC&d@ |
Underline-Disable |
|
|
|
ESC&d#A |
Number of Collated Copies |
|
|
|
ESC&d#D |
Underline-Enable |
|
|
|
ESC&f#F |
Set Universal Height |
|
|
|
ESC&f#G |
Set Universal Width |
|
|
|
ESC&f#O |
Set Universal Feed Direction |
|
|
|
ESC&f#W |
Set Universal Custom Name |
|
|
|
ESC&f#S |
Push / Pop Cursor Position |
|
|
|
ESC&f#X |
Macro Control |
|
|
|
ESC&f#Y |
Set Macro ID |
|
|
|
ESC&k#G |
Set Line Termination |
|
|
|
ESC&k#H |
Set Horizontal Motion Index |
|
|
|
ESC&k#S |
Select Primary and Secondary Pitch |
|
|
|
ESC&k#W |
Text Scale Mode |
X |
X |
|
ESC |
&l#A |
Set Page Size |
|
|
|
|
|
|
|
ESC |
&l#C |
Set Vertical Motion Index |
|
|
|
|
|
|
|
ESC |
&l#D |
Set Line Spacing |
|
|
|
|
|
|
|
ESC |
&l#E |
Set Top Margin |
|
|
|
|
|
|
|
ESC |
&l#F |
Set Text Length |
|
|
|
|
|
|
|
ESC |
&l#G |
Set Output Bin |
|
|
|
|
|
|
|
ESC |
&l#H |
Paper Source |
|
|
|
|
|
|
|
ESC |
&l#L |
Skip Perforation |
|
|
|
|
|
|
|
ESC |
&l#O |
Select Orientation |
|
|
|
|
|
|
Appendix A: PCL support
23
|
= Supported |
|
|
|
X = Not supported |
|
Printer model |
||
|
|
|
C540n, C543dn, C544n, |
|
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
|
ESC |
&l#M(b) |
Paper Type |
X |
X |
|
|
|
|
|
ESC |
&l#P |
Set Page Length |
|
|
|
|
|
|
|
ESC |
&l#S |
Simplex/Duplex Print |
|
|
|
|
|
|
|
ESC |
&l#U |
Long-Edge Offset Registration |
|
|
|
|
|
|
|
ESC |
&l#X |
Number of Copies |
|
|
|
|
|
|
|
ESC |
&l#Z |
Short-Edge Offset Registration |
|
|
|
|
|
|
|
ESC |
&l1T |
Job Separation |
X |
X |
|
|
|
|
|
ESC&n#W [operation] [string id] |
Alphanumeric ID |
|
|
|
ESC&p#C |
Palette Control |
|
|
|
ESC&p#I |
Palette Control ID |
|
|
|
ESC&p#S |
Select Palette |
|
|
|
ESC&p#X[data] |
Transparent Print Data |
|
|
|
ESC&r#F |
Flush All Pages |
|
|
|
ESC&s#C |
End-Of-Line Text Wrap |
|
|
|
ESC&t#P |
Text Parsing Method |
|
|
|
ESC&u#D |
Unit of Measure |
|
|
|
ESC(# |
Primary Font Symbol Set |
|
|
|
ESC(#X |
Select Primary Download Font (by |
|
|
|
|
|
Font ID) |
|
|
ESC(3@ |
Select Default Primary Font |
|
|
|
ESC(f#W[data] |
Define Symbol Set |
|
|
|
ESC(s#B |
Primary Font Stroke Weight |
|
|
|
ESC(s#H |
Primary Font Pitch |
|
|
|
ESC(s#P |
Primary Font Spacing |
|
|
|
ESC(s#S |
Primary Font Style |
|
|
|
ESC(s#T |
Primary Font Typeface Selection |
|
|
Appendix A: PCL support
24
= Supported |
|
|
|
X = Not supported |
|
Printer model |
|
|
|
C540n, C543dn, C544n, |
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
ESC(s#V |
Primary Font Height (Point Size) |
|
|
ESC(s#W[data] |
Load Character |
|
|
ESC)# |
Secondary Font Symbol Set |
X |
X |
ESC)#X |
Select Secondary Download Font |
X |
X |
|
(by Font ID) |
|
|
ESC)3@ |
Select Default Secondary Font |
|
|
ESC)s#B |
Secondary Font Stroke Weight |
X |
X |
ESC)s#H |
Secondary Font Pitch |
X |
X |
ESC)s#P |
Secondary Font Spacing |
X |
X |
ESC)s#S |
Secondary Font Style |
X |
X |
ESC)s#T |
Secondary Font Typeface Selection |
X |
X |
ESC)s#V |
Secondary Font Height (Point Size) |
X |
X |
ESC)s#W[data] |
Load Font Header |
|
|
ESC*b#M |
Set Raster Compression Mode |
|
|
ESC*b#V[data] |
Transfer Raster Data (by Plane) |
|
|
ESC*b#W[data] |
Transfer Raster Data |
|
|
|
(by Row / Block) |
|
|
ESC*b#Y |
Y Offset |
|
|
ESC*c#A |
Horizontal Rectangle Size |
|
|
|
(in PCL Units) |
|
|
ESC*c#B |
Vertical Rectangle Size (in PCL Units) |
|
|
ESC*c#D |
Set Font ID |
|
|
ESC*c#E |
Set Character Code |
|
|
ESC*c#F |
Font Control |
|
|
ESC*c#G |
Area Fill ID |
|
|
ESC*c#H |
Horizontal Rectangle Size |
|
|
|
(in Decipoints) |
|
|
ESC*c#K |
GL/2 Horizontal Plot Size (in Inches) |
|
|
ESC*c#L |
GL/2 Vertical Plot Size (in Inches) |
|
|
Appendix A: PCL support
25
|
= Supported |
|
|
|
X = Not supported |
|
Printer model |
||
|
|
|
C540n, C543dn, C544n, |
|
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
|
ESC*c#P |
Fill Rectangular Area |
|
|
|
ESC*c#Q |
Pattern Control |
|
|
|
ESC*c#R |
Symbol Set ID Code |
|
|
|
ESC*c#S |
Symbol Set Control |
|
|
|
ESC*c0T |
Set Picture Frame Anchor Point |
|
|
|
ESC*c#V |
Vertical Rectangle Size |
|
|
|
|
|
(in Decipoints) |
|
|
ESC*c#W[data] |
User-Defined Pattern |
|
|
|
ESC*c#X |
Picture Frame Horizontal Size |
|
|
|
|
|
(in Decipoints) |
|
|
ESC*c#Y |
Picture Frame Vertical Size |
|
|
|
|
|
(in Decipoints) |
|
|
ESC |
*l#O |
Logical Operation |
|
|
|
|
|
|
|
ESC |
*l#R |
Pixel Placement |
|
|
|
|
|
|
|
ESC |
*l#W[data] |
Color Lookup Tables |
X |
X |
|
|
|
|
|
ESC*m#W[data] |
Download Dither Matrix |
|
|
|
ESC*o#M(b) |
Print Quality |
X |
X |
|
ESC*o#Q |
Mechanical Print Quality |
X |
X |
|
ESC*o#W[data] |
Driver Configuration Command |
|
|
|
ESC*p#P |
Push / Pop Palette |
|
|
|
ESC*p#R |
Set Pattern Reference Point |
|
|
|
ESC*p#X |
Horizontal Cursor Position |
|
|
|
|
|
(in PCL Units) |
|
|
ESC*p#Y |
Vertical Cursor Position |
|
|
|
|
|
(in PCL Units) |
|
|
ESC*r#A |
Start Raster Graphics |
|
|
|
ESC*r#F |
Raster Graphics Presentation Mode |
|
|
|
ESC*r#S |
Raster Width (Source) |
|
|
|
ESC*r#T |
Raster Height (Source) |
|
|
Appendix A: PCL support
26
= Supported |
|
|
|
X = Not supported |
|
Printer model |
|
|
|
C540n, C543dn, C544n, |
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
ESC*r#U |
Simple Color |
|
|
ESC*rB |
End Raster Graphics (Version B) |
|
|
ESC*rC |
End Raster Graphics (Version C) |
|
|
ESC*s#I |
Inquire Status Readback Entity |
|
|
ESC*s1M |
Free Space |
|
|
ESC*s#T |
Set Status Readback Location Type |
|
|
ESC*s#U |
Set Status Readback Location Unit |
|
|
ESC*s#X |
Echo |
|
|
ESC*t#H |
Raster Width Destination |
|
|
ESC*t#I |
Gamma Correction |
|
|
ESC*t#J |
Render Algorithm |
X |
X |
ESC*t#K |
Scale Algorithm |
X |
X |
ESC*t#R |
Raster Resolution |
|
|
ESC*t#V |
Raster Height Destination |
|
|
ESC*g#W |
Set Raster Configuration |
X |
X |
ESC*v#A |
Color Component One |
|
|
ESC*v#B |
Color Component Two |
|
|
ESC*v#C |
Color Component Three |
|
|
ESC*v#I |
Assign Color Index |
|
|
ESC*v#N |
Source Transparency Mode |
|
|
ESC*v#O |
Pattern Transparency Mode |
|
|
ESC*v#S |
Foreground Color |
|
|
ESC*v#T |
Select Current Pattern |
|
|
ESC*v#W[data] |
Configure Image Data |
|
|
ESC*i#W[data] |
Viewing Illuminant |
X |
X |
ESC9 |
Clear Horizontal Margins |
|
|
Appendix A: PCL support
27
|
= Supported |
|
|
|
|
X = Not supported |
|
Printer model |
|
|
|
|
C540n, C543dn, C544n, |
|
|
|
|
C544dn,C544dw, |
|
|
Command |
Function |
C544dtn |
X546dtn |
|
ESC= |
Half Line-Feed |
|
|
|
ESC%#A |
Enter PCL Emulation |
|
|
|
ESC%#B |
Enter GL/2 Language |
|
|
|
|
Note: The values of -1, 2, and 3 are |
|
|
|
|
not supported by any of the printers |
|
|
|
|
included in this document. |
|
|
|
|
|
|
|
|
ESC%- 12345X |
Universal Exit Language (UEL) / |
|
|
|
|
Start of PJL |
|
|
|
|
|
|
|
= Supported |
|
|
|
X = Not supported |
|
Printer model |
|
|
|
C540n, C543dn, C544n, |
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
AA |
Arc Absolute |
|
|
AC |
Anchor Corner |
|
|
AD |
Define Alternate Font |
|
|
AR |
Arc Relative |
|
|
AT |
Arc Absolute Three Point |
|
|
BR |
Bezier Relative |
|
|
BZ |
Bezier Absolute |
|
|
CF |
Character Fill |
|
|
CI |
Circle |
|
|
CO |
Comment |
|
|
CP |
Character Plot |
|
|
CR |
Set Color Range |
|
|
DF |
Default |
|
|
DI |
Absolute Direction |
|
|
Appendix A: PCL support
28
= Supported |
|
|
|
X = Not supported |
|
Printer model |
|
|
|
C540n, C543dn, C544n, |
|
|
|
C544dn,C544dw, |
|
Command |
Function |
C544dtn |
X546dtn |
DR |
Relative Direction |
|
|
DT |
Define Label Terminator |
|
|
DV |
Define Variable Text Path |
|
|
EA |
Edge Rectangle Absolute |
|
|
EP |
Edge Polygon |
|
|
ER |
Edge Rectangle Relative |
|
|
ES |
Extra Space |
|
|
EW |
Edge Wedge |
|
|
FI |
Primary Font |
|
|
FN |
Secondary Font |
|
|
FP |
Fill Polygon, Odd/Even |
|
|
FP |
Fill Polygon, Non-Zero Winding |
|
|
FT |
Fill Type |
|
|
FT |
Fill Type - 22 |
|
|
FT |
Fill Type - 9 |
|
|
IN |
Initialize |
|
|
IP |
Input P1 and P2 |
|
|
IR |
Input Relative P1 and P2 |
|
|
IW |
Input Window |
|
|
LA |
Line Attributes |
|
|
LB |
Label, Default Terminator = '03'x |
|
|
LO |
Label Origin |
|
|
LO |
Uses PCL Label Origin |
|
|
LT |
Line Type |
|
|
MC |
Logical Operation |
|
|
NP |
Number of Pens |
|
|
Appendix A: PCL support
29
|
= Supported |
|
|
|
|
X = Not supported |
|
Printer model |
|
|
|
|
C540n, C543dn, C544n, |
|
|
|
|
C544dn,C544dw, |
|
|
Command |
Function |
C544dtn |
X546dtn |
|
PA |
Plot Absolute |
|
|
|
|
|
|
|
|
PC |
Set Pen Color |
|
|
|
|
|
|
|
|
PD |
Pen Down |
|
|
|
|
|
|
|
|
PE |
Polyline Encoded |
|
|
|
|
|
|
|
|
PM |
Polygon Mode |
|
|
|
|
|
|
|
|
PP |
Pixel Placement |
|
|
|
|
|
|
|
|
PR |
Plot Relative |
|
|
|
|
|
|
|
|
PU |
Pen Up |
|
|
|
|
|
|
|
|
PW |
Pen Width |
|
|
|
|
|
|
|
|
RA |
Fill Rectangle Absolute |
|
|
|
|
|
|
|
|
RF |
Define Raster Fill |
|
|
|
|
|
|
|
|
RO |
Rotate Coordinate System |
|
|
|
|
|
|
|
|
RR |
Fill Rectangle Relative |
|
|
|
|
|
|
|
|
RT |
Arc Relative Three Point |
|
|
|
|
|
|
|
|
SA |
Select Alternate Font |
|
|
|
|
|
|
|
|
SB |
Scalable/Bitmapped Fonts |
|
|
|
|
|
|
|
|
SC |
Scale |
|
|
|
|
|
|
|
|
SD |
Define Standard Font |
|
|
|
|
|
|
|
|
SI |
Absolute Character Size |
|
|
|
|
|
|
|
|
SL |
Character Slant |
|
|
|
|
|
|
|
|
SM |
Symbol Mode |
|
|
|
|
|
|
|
|
SP |
Select Pen |
|
|
|
|
|
|
|
|
SR |
Relative Character Size |
|
|
|
|
|
|
|
|
SS |
Select Standard Font |
|
|
|
|
|
|
|
|
SV |
Screened Vectors |
|
|
|
|
|
|
|
|
SV |
Screened Vectors - 9, level |
|
|
|
|
|
|
|
Appendix A: PCL support
30