GB
Operating instruction
Time switch D22 - 2 Channel
047 71 / 604 770 / 604 772
®
|
|
|
|
|
Overview of programmed |
||
Channel display |
|
|
|
switching times for the week. |
|||
|
|
|
|
|
Resolution 0.5h |
||
Function |
|
|
|
Switch status of the current |
|||
|
|
|
|
|
|||
Receptacle for |
|
|
|
channel |
|
||
|
|
|
|
|
|
||
data key |
|
|
|
Day, Time, Date |
|||
|
|
+ |
+ |
|
|
|
|
1800W |
1800W |
1800W |
2300W |
100W |
100W |
1800W |
2300W |
General information
•Start-up: after applying the supply voltage, the time switch starts automatically with the last selected function. The relay position is set by the current program.
•Battery backup
-Backlighting not active
-Data key READ/WRITE only via the menu.
•For saftety, when the time switch is connected to the mains supply the contact should not be used on an isolated low voltage supply and when the time switch is connected to the isolated voltage supply the contact should not be used on the mains supply.
Select menu, back to main menu,
Hold down > 1s = operating display
Confirm selection or load parameters
|
|
|
|
|
• Select menu options or set parameters |
C1 |
C2 |
• Channel selection |
Overview |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Technical data |
|
|
|
Set language |
|
047 71 |
604 770 |
604 772 |
|
Supply voltage: |
230V 50/60Hz |
120V 50/60Hz |
24V AC/DC |
|
Consumption : |
ca. 1 W |
|
|
|
Contact rating: |
2 changeover contact 16A 250V~µ cos ϕ = 1 |
|
||
Parallel compensation |
60VA max. 7µF |
|
|
|
Accuracy : |
± 0,2 s /day under typical installation conditions |
|
|
|
|
single strand |
multi strand |
|
|
Terminal capacity: |
|
1,5...4 mm2 |
1,5...2,5 mm2 |
|
|
|
Programmes: |
28 per channel |
|
|
|
||
|
|
|
||||
Battery reserve: |
|
6 years |
|
|
|
|
Storage ambient: |
|
-20°C to +60°C |
|
|
|
|
Working ambient: |
-20°C to +55°C |
|
|
|
||
|
|
|
|
|
|
|
N 291952/02
Set time/date, summertime/wintertime and holiday period
Summertime: ± 1 hour Europe: Factory set.
SPECIAL: The switchover to/from summertime can be freely programmed by entering a start date and end date
and is then executed each year on the same day of the week, e.g. Sunday.
Holiday
After activation, the holiday program is executed between 0:00h on the start date and 24:00h on the end date (Constant ON/OFF). After the holiday program has run once, it must be reactivated.
Programming
A program consists of an ON time, OFF time and associated ON and OFF days. Programs with predefined on/off days (Mon to Sun, Mon to Fri and Sat and Sun): for these programs, you only need to set
the switching times. With the "INDIVIDUAL” option, you can allocate switching times to specific days of your choice. The programs of a channel are linked to one another
by logical OR.
Set MON and TUES as on/off days
*
CHRONO* = All switch commands are executed in chronological order in a week
INPUT = Programs are executed in the order in which they are entered
Modes
• Auto - Automatic operation
• Constant ON
• Constant OFF
• Extra
The switch status imposed by the program is inverted (manual override).
With the next effective switch command, the time switch resumes control of on/off switching.
Reset |
MENU OK |
Warning!
The memory will be cleared, and all set data will be lost.
Hold down all keys simultaneously for about 2 seconds and release.
The language, time, date, summertime/wintertime and switching times will have to be re-entered.
Additional function descriptions are provided on the attached sheet.