Page 1
Short Instruction
NanoPix Cyc
from software version: V2.1
Released: 12-2017 - V1.1 - Rev B
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Page 2
Safety Guidelines
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Wien, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
» Please read these safety guidelines carefully before you take the
NanoPix Cyc into service.
» Check the suitability of the product for the intended use.
» The NanoPix Cyc is not suitable for outdoor use (IP20).
» Do not attempt to repair or dismantle the NanoPix Cyc xture: Opening and
removing the internal covers can result in electrocution or other serious
injuries.
» In case of product failure, please contact LDDE or an authorised LDDE-
dealership.
» Do not touch the xture while it is in use.
» Disconnent the xture from the power supply before re-positioning and
cleaning.
» Ensure that when the luminaire systems are installed in decorations, a
sufcient clearance of around 30cm is required for adequate cooling and
ventilation.
» Protect the xture from shocks and impacts.
» Protect the xture from moisture and water and avoid contact with moist or
wet appliances.
» Ensure that the xture is not covered and adequate ventilation is in place.
» Do not insert objects into openings of the housing that are connected to live
parts as this can lead to short circuiting. Danger of electric shock and risk
of re.
» The xture is to be removed from service if:
• there is visible damage
• parts have become lose
• there is visible damage to cable connections
» LDDE products are manufactured and delivered in concordance with EU
directive 2002/96/EU of the European Parliament and the Council on
Waste Electrical and Electronic Equipment WEEE). Help protect the environment and dispose of used products at your local recycling station.
Your dealership can offer further advice on correct disposal.
Page 3
Menu structure and operation
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Menu structure
As soon as the NanoPix Cyc is supplied with power, the integrated OLED display lights up.
Now, perform the appropriate system conguration on the unit using the control panel located on the top of the
unit. It is recommended to carry out all congurations in advance of the installation on the devices. The respective
system settings are explained in the following points.
Operation
The menu is controlled by 5 buttons: Up, Down, Left, Right and OK.
In the main menu, you can jump through the individual menu items only with Left / Right.
If you wish to change a setting, press the OK key, then the setting to be changed will ash.
Then use Up / Down to change the setting and conrm with OK.
During the saving process, „Saving ...“ is displayed in the lower display line.
Page 4
Settings
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
DMX address
In this menu the DMX start address is set in the range 1 - 512.
Channelmode
You can choose between 9 DMX modes, each designed for different applications and preferences.
CH5 - COLOR MODE (5 CHANNELS):
Only colors (RGB, WW, CW) - No intensity and strobe channel available.
CH7 - NORMAL MODE (7 CHANNELS):
Most common mode with all basic functions.
CH10 - HIGH RESOLUTION COLOR MODE (10 CHANNELS):
Same as Ch5 - Color Mode, but with 16-bit dimming.
CH15 - PIXEL MODE (15 CHANNELS)
3 LED modules are individually controlled with 8-bit dimming.
No intensity and strobe channel available.
CH16 - PIXEL MASTER MODE (16 CHANNELS)
Same as the Ch15 - Pixel Mode, additionally with intensity channel.
CH17 - PIXEL MASTER + STROBE MODE (17 CHANNELS)
Same as Ch16 - Pixel Master Mode, additionally with strobe channel.
CH30 - HIGH RESOLUTION PIXEL MODE (30 CHANNELS)
Same as Ch15 - Pixel Mode, but with 16-bit dimming.
CH11 - HIGH RESOLUTION COLOR STROBE MODE (11 CHANNELS)
Same as Ch10 - High Resolution Color Mode, additionally with 8-bit strobe.
CH31 - HIGH RESOLUTION PIXEL + STROBE MODE (31 CHANNELS)
Same as Ch30 - High Resolution Pixel Mode, additionally with 8-bit strobe.
8-bit Modes
16-bit Modes
Page 5
DMX Chart 8-bit
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
Channelmode 8-bit
The following table shows the various available modes for 8-bit control and the DMX channels required for
the corresponding mode.
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Ch LED
module
8-bit
interpolated
Ch 5 Ch 7 Ch 15 Ch 16 Ch 17
1 Intensity xxx 1 xxx 1 1
2
1
R (red) 1 2 1 2 2
3 G (green) 2 3 2 3 3
4 B (blue) 3 4 3 4 4
5 WW (warm white) 4 5 4 5 5
6 CW (cold white) 5 6 5 6 6
7
2
R (red) 1 2 6 7 7
8 G (green) 2 3 7 8 8
9 B (blue) 3 4 8 9 9
10 WW (warm white) 4 5 9 10 10
11 CW (cold white) 5 6 10 11 11
12
3
R (red) 1 2 11 12 12
13 G (green) 2 3 12 13 13
14 B (blue) 3 4 13 14 14
15 WW (warm white) 4 5 14 15 15
16 CW (cold white) 5 6 15 16 16
17 Strobe xxx 7 xxx xxx 17
18 Control Channel (6) (8) (16) (17) (18)
DMX Chart
Page 6
DMX Chart 16-bit
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Ch LED
module
16-bit Ch 10 Ch 11 Ch 30 Ch 31
1
1
red 1 1 1 1
2 red ne 2 2 2 2
3 green 3 3 3 3
4 green ne 4 4 4 4
5 blue 5 5 5 5
6 blue ne 6 6 6 6
7 warm white 7 7 7 7
8 warm white ne 8 8 8 8
9 cold white 9 9 9 9
10 cold white ne 10 10 10 10
11
2
red 1 1 11 11
12 red ne 2 2 12 12
13 green 3 3 13 13
14 green ne 4 4 14 14
15 blue 5 5 15 15
16 blue ne 6 6 16 16
17 warm white 7 7 17 17
18 warm white ne 8 8 18 18
19 cold white 9 9 19 19
20 cold white ne 10 10 20 20
21
3
red 1 1 21 21
22 red ne 2 2 22 22
23 green 3 3 23 23
24 green ne 4 4 24 24
25 blue 5 5 25 25
26 blue ne 6 6 26 26
27 warm white 7 7 27 27
28 warm white ne 8 8 28 28
29 cold white 9 9 29 29
30 cold white ne 10 10 30 30
31 Strobe xxx 11 xxx 31
32 Control Channel (11) (12) (31) (32)
DMX Chart
Channelmode 16-bit
The following table shows the various available modes for 16-bit control and the DMX channels required for
the corresponding mode.
Page 7
Settings
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
PWM frequency
Changes to the PWM frequency can be performed here.
The possible settings can be found in the table below.
Quiet Mode
The Quiet Mode is designed for noise-sensitive applications, for this purpose the fans can be switched on and off.
The stepless regulation of the fans is monitored with a temperature sensor.
Manual Mode
In manual mode, the NanoPix Cyc can be set to any color, including strobe.
The NanoPix Cyc is then in the Ch7 - Normal Mode and the following settings can be made directly in the
menu using the selection keys.
I Intensity between DMX value 0-255
R Red of DMX value 0-255
G Green of DMX value 0-255
B Blue of DMX value 0-255
WW Warm white of DMX value 0-255
CW Cold white of DMX value 0-255
St Strobe of DMX value 0-255
DMX value 0-25 no Strobe
DMX value 26-228 - Strobe frequency from 1Hz to 25Hz
DMX value 229-255 no Strobe
OFF
The fans are switched on from a temperature of 40°C and
controlled depending on the temperature.
From a temperature of 56°C, the brightness is also adjusted.
ON
When the Quiet Mode is activated, no fan is used,
the maximum brightness is limited to 70%.
If the measured temperature exceeds 79°C, the fan is switched on
for safety reasons in order to avoid damage to the device.
750 Hz PWM frequency 750 Hz
1500 Hz PWM frequency 1500 Hz
3000 Hz PWM frequency 3000 Hz
Page 8
Settings
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Test Mode
In this mode, the intensity is continuously scaled up and down from 0-100%, whereby the speed of the dimming
process can be adjusted in 10 steps. The display shows a bar indicating the current speed.
In Test Mode three different test programs are available, see table below.
Use the Up / Down buttons to select the desired mode.
Use the Left / Right buttons to set the dimming speed.
Single All colors are tested in sequence.
RGB RGB is tested jointly.
RGBWWCW All colors are tested simultaneously.
Standalone Mode
In this mode 10 xed colors are available, which are selected with the Up / Down keys.
Use the Left / Right keys to change the brightness, which is displayed as a bar in the lower line of the display.
R G B WW CW
Magenta 255 0 255 0 0
Lavender 255 0 255 0 255
CT Blue 0 115 255 0 255
Light Green 0 255 84 118 0
Cyan 0 255 255 0 0
Yel l ow 255 255 0 0 0
Light Yellow 255 255 0 255 0
Amber 255 166 0 0 0
Warm White 255 216 0 255 255
Cold White 176 255 255 255 255
Control Channel
If the control channel is activated, various functions of the NanoPix Cyc can be switched on and off
via an additional DMX channel.
Control:
1. Set the Control Channel to the respective value.
2. No value change for at least 3 seconds.
3. Then ash directly to 0.
4. New setting is saved.
PWM frequency 750 Hz 11 - 20 DMX value
PWM frequency 1500 Hz 21 - 30 DMX value
PWM frequency 3000 Hz 31 - 40 DMX value
Quiet Mode ON 101 - 110 DMX value
Quiet Mode OFF 111 - 120 DMX value
Fade to Zero ON 201 - 210 DMX value
Fade to Zero OFF 211 - 220 DMX value
Page 9
Settings
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Fade to Zero
OFF For a new DMX value (below DMX value 15) --> Snap to 0.
ON For a new DMX value (below DMX value 15) is dimmed to 0.
Factory Default
Factory Default
DMX start adress 1
Channelmode Ch7 - Normal Mode
Quiet Mode OFF
PWM frequency 750 Hz
Control Channel OFF
Fade to Zero ON
Display Rotate OFF
Temperature
<10°C The measured temperature is below 10°C.
XX °C The measured temperature is shown in the display.
Check
Sensor
Contact an authorized LDDE dealer or contact Technical Support
at service@ldde.com
This menu displays the current temperature of the NanoPix Cyc. The value is updated every 10 seconds.
When the NanoPix Cyc is switched on, „-“ is displayed in the display for 10 seconds, after which the following
information appears.
Software Version
The display shows the current software version.
NP Cyc Rotate
The display and the control of the LED modules can be rotated 180 degrees.
Tech Support
The display shows service@ldde.com
Page 10
Technical Specications
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
Dimensions / Weight
Length .................................................................................................................. 610 mm / 24,01 Inches
Width ..................................................................................................................... 334 mm / 13,15 Inches
Height ..................................................................................................................... 140 mm / 5,51 Inches
Weight (without accessories)............................................................................................ 10 kg / 22,04 lb
Control
Protocol .............................................................................................................................. DMX512/1990
Daisy chaining ........................................................................................................ max. 10 NanoPix Cyc
Dimming
Dimming ...................................................................................................... Continous Dimmer 0 - 100%
DMX-Kanäle ............................................................. 5 / 7 / 10 / 11 / 15 / 16 / 17 / 30 / 31 DMX-Channels
Conguration ..................................................................................................................... OLED Display
Light Source
LED Engine ................................................................................................ RGB, warm white, cold white
Average life span .................................................................................................... approx. 30.000 hours
Connections
Input / Output ...................................................................... Neutrik PowerCon In/Out + XLR 5-pol In/Out
Electrical specications
Input voltage range ................................................................................................ 100-240VAC | 50/60Hz
Max. power consumption .................................................................................................................210VA
Construction
Housing ............................................................................................. Aluminium continous casting prole
Color ................................................................................................................................................ black
Minimum clearance of the LED ......................................................................................................100mm
Minimum clearance for sufcient cooling .....................................................................................300mm
Cooling ....................................................................................................... Sensor-controlled fan system
Protection class .................................................................................................................................. IP20
Safety standards
Certications ...................................... EN 55015, EN 60598-1, EN 61000-3-2, EN 61000-3-3, EN 61547
Photobiological safety according to IEC 62471:2008 / EN 62471:2008
Temperatures
Maximum ambient temperature ................................................................................... ta: +40ºC / +104°F
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Page 11
Dimensions
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Page 12
Photometric data
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Vienna, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Distance: 1,5m
Distance: 2,5m
Distance: 2,0m
The following gures show the light distribution at different distances and positions relative to the background.
Distance to the background (A) 2m
Distance between NanoPix Cyc (B) 2m
Warm white (WW) 100%
Conversion factor („warm white“ = 100%):
„cold white“..........120%
„red“.....................20% Example: 100% WW = 300lx --> 100% CW = 360lx
„green“.................80%
„blue“...................15% ( Photometrical tolerance +/- 10% )
Page 13
EC Declaration of Conformity
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Wien, Austria
P: +43 1 7671811 0, F: +43 1 7671811 99
E: ofce@ldde.com; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Loading...