Size:
61.91 Kb
Download

2-10-00

file: 091-18WP-XX

INSTRUCTION MANUAL

AUTO EJECT WP

AUTOMATIC SHORE LINE DISCONNECT

1 YEAR WARRANTY

KUSSMAUL ELECTRONICS CO., INC.

170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796-1221

TEL: in NY 631-567-0314

TOLL FREE: 800-346-0857

FAX: 631-567-5826

CAUTION

The AUTO EJECT must be connected to the starter circuit so that the solenoid is energized only while the engine is cranking. If the solenoid is energized continuously it will OVERHEAT and BURN OUT.

If the AUTO EJECT is installed where the rear mechanism can accumulate dirt, grime or water you must install a 091-18CP

Rear Enclosure.

FAILURE TO FOLLOW

THESE CAUTION

NOTES WILL VOID THE

WARRANTY

INSTALLATION INSTRUCTIONS

1.Locate a convenient place on the vehicle to mount the AUTO EJECT. A minimum clearance of 4” behind the mounting panel is required as well as 3 3/4” below the center line to clear the ejection mechanism.

2.Place the template in position and center punch in 7 places.

3a. Drill 2 holes, 1/2” diameter. IMPORTANT THESE HOLES MUST BE DRILLED FIRST. 3b. Drill 4 mounting holes, 3/16” diameter and one, 2 1/4” clearance hole for the AUTO EJECT.

4.Connect one terminal of the solenoid on the AUTO EJECT to the vehicle ground and the other solenoid terminal to the vehicle’s starter. USE #16 GAUGE WIRE OR HEAVIER.

5.Crimp the ring lugs on the wire and connect the Green, Black, and White power wires to the accessories on the vehicle.

6.Test installation by installing mating connector into the AUTO EJECT. Energizing the starter should energize the solenoid and eject the connector.

7.Keep connector and contacts of the AUTO EJECT clean. Clean contacts with WD-40solvent as required. Lubricate contacts monthly with “vaseline” to insure free operation.

NOTE: USE ONLY CORD CONNECTOR SUPPLIED WITH THE AUTO EJECT

All connectors are not identical, using a substitue may result in unreliable operation or failure of the AUTO EJECT to operate.

 

Note: The Auto Eject is on the

Note: use 12 gauge wire for 20 amps

 

outside of the truck wall.

and 14 gauge wire for 15 amps.

#8 Screw

#8 Hex Nut

 

 

Green

Ground

 

Black

 

Line

 

 

 

White

Neutral

 

 

 

Ring lugs supplied

Weather

 

Solenoid

Proof Cover

 

 

 

 

 

To Battery

Gasket

 

 

Truck Wall

 

 

 

Chassis

Vehicle Starter

 

Ground

 

C

 

L

 

C

 

L

3.250

2.125

 

C

 

L

 

1.875

3/16” DIA HOLE

C

L

2 1/4” DIA HOLE

DRILL THESE TWO HOLES FIRST 1/2” DIA HOLE

Hole Template

AUTOEJECT AUTOEJECT DYNAMICDISCONNECT ENCLOSURE

MODEL#091-18-098

The Model 091-18-098Dynamic Disconnect is a coupling device wired between an Auto Eject and the vehicle and serves to only connect the A.C. power after the plug has been inserted into the Auto Eject. Upon vehicle startup the Dynamic Disconnect opens the load circuit before ejecting the plug. By providing the time delays on both application and removal of power, no arcing can occur at the connector. Note A.C. power must be present at the shore line connector in order to operate the Dynamic Disconnect.

MODEL # 091-18CP

The Enclosure is fabricated from aluminum and contains a cutout and captive fasteners to mate with the Auto EJect mounting screws. Providing protection from road dirt and damage, this unit suggested for all Auto Eject installations in which the mechanism is exposed to the elements or subject to damage.

INSTALLATION RECORD & WARRANTY

Date Installed

Installed By

Vehicle Identification

Vehicle Owner

WARRANTY

All product of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 1 years from the date the equipment was shipped.

Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and /or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others.