Kuppersberg ECO 302 User manual

TechnicalpassporTпаспорт технического изделия

ECO 301, ECO 601, ECO 601 C, ECO 601 GR,

ECS603, ECS603 C, ECS603 GR,

ICS604, ICS604 C, ICS604 GR

ELECTRIC HOB

ЭЛЕКТРИЧЕСКАЯ ВАРОЧНАЯ ПОВЕРХНОСТЬ

Technical passporT

english

english

Technical passporT

electric hob
cOntentS
PART 1. SAFETY WARNINGS................................................................................................	3
PART 2. INSTALLATION .........................................................................................................	6
PART 3. OPERATION INSTRUCTIONS ............................................................................	9
PART 4. CLEANING AND MAINTENANCE.....................................................................	23

electric hob

congratulations

on the purchase of your new hob and thank you for choosing us!

please read all the safety instructions carefully before use and keep this manual for future reference.

part 1. Safety WarninGS Safety Warnings

Your safety is important to us. Please read below information carefully before installing or using your Hob.

inStaLLatiOn electrical Shock Hazard

ÂDisconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.

ÂConnection to a good earth wiring system is essential and mandatory.

ÂAlterations to the domestic wiring system must only be made by a qualifi ed electrician.

ÂFailure to follow this advice may result in electrical shock or death.

cut Hazard

ÂTake care - panel edges are sharp.

ÂFailure to use caution could result in injury or cuts.

important safety instructions

ÂRead these instructions carefully before installing or using this appliance.

ÂNo combustible material or products should be placed on this appliance at any time.

ÂPlease make this information available to the person responsible for installing the hob as it could reduce your installation costs.

ÂIn order to avoid a hazard, this appliance must be installed according to these instructions for installation.

ÂThis appliance is to be properly installed and earthed only by a suitably qualifi ed person.

ÂThis appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply.

ÂFailure to install the appliance correctly could invalidate any warranty or liability claims.

2

3

Technical

passport

English

English

Technical

passport

Electric Hob

Electric Hob

Operation and maintenance

ÂÂ

Do not place or leave any magnetisable objects (e.g. credit cards, memory

Electrical Shock Hazard

cards) or electronic devices (e.g. computers, MP3 players) near the appliance, as they

may be affected by its electromagnetic field.

ÂÂ

Do not cook on a broken or cracked hob. If the hob surface should break or

ÂÂ

Never use your appliance for warming or heating the room.

crack, switch the appliance off immediately at the mains power supply (wall switch)

ÂÂ

After use, always turn off the cooking zones and the hob as described in this

and contact a qualified technician.

manual. Do not rely on the pan detection feature to turn off the cooking zones when

ÂÂ

Switch the hob off at the wall before cleaning or maintenance.

you remove the pans.

ÂÂ

Do not allow children to play with the appliance or sit, stand, or climb on it.

ÂÂ

Failure to follow this advice may result in electrical shock or

ÂÂ

Do not store items of interest to children in cabinets above the hob. Children

death.

climbing on the hob could be seriously injured.

Health Hazard

ÂÂ

Do not leave children alone or unattended in the area where the appliance

ÂÂ

This appliance complies with electromagnetic safety standards.

is in use.

ÂÂ

However, persons with cardiac pacemakers or other electrical implants (such

ÂÂ

Children or persons with a disability which limits their ability to use the

appliance should have a responsible and competent person to instruct them in

as insulin pumps) must consult with their doctor or implant manufacturer before

its use. The instructor should be satisfied that they can use the appliance without

using this appliance to make sure that their implants will not be affected by the

danger to themselves or their surroundings.

electromagnetic field.

ÂÂ

Do not repair or replace any part of the

appliance unless specifically

ÂÂ

Failure to follow this advice may result in death.

recommended in the manual. All other servicing should be done by a qualified

Hot Surface Hazard

technician.

ÂÂ

During use, accessible parts of this appliance will become hot enough to

ÂÂ

Do not use steam cleaner to clean hob.

ÂÂ

Do not place or drop heavy objects on hob.

cause burns.

ÂÂ

Do not stand on your hob.

ÂÂ

Do not let your body, clothing or any item other than suitable cookware

ÂÂ

Do not use pans with jagged edges or drag pans across the ceramic glass

contact the ceramic glass until the surface is cool.

surface as this can scratch the glass.

ÂÂ

Beware: Metallic objects such as knives, forks, spoons and lids should not be

ÂÂ Do not use scourers or any other harsh abrasive cleaning agents to clean your

placed on the hob surface since they can get hot.

hob, as these can scratch the ceramic glass.

ÂÂ

Keep children away.

ÂÂ

If the power supply cable is damaged, it must only be replaced by qualified

ÂÂ

Handles of saucepans may be hot to touch. Check saucepan handles do not

technician.

overhang other cooking zones that are on. Keep handles out of reach of children.

ÂÂ

This appliance is intended to be used in household and similar applications

ÂÂ

Failure to follow this advice could result in burns and scalds.

such as:-staff kitchen areas in shops,offices and other working environments;-farm

Cut Hazard

houses; -by clients in hotels, motels and other residential type environments; -bed

and breakfast type environments.

ÂÂ

The razor-sharp blade of a hob scraper is exposed when the safety cover is

ÂÂ

This appliance can be used by children aged from 8 years and above and

retracted. Use with extreme care and always store safely and out of reach of children.

persons with reduced physical, sensory or mental capabilities or lack of experience

ÂÂ

Failure to use caution could result in injury or cuts.

and knowledge if they have been given supervision or instruction concerning use

Important safety instructions

of the appliance in a safe way and understand the hazards involved. Children shall

not play with the appliance. Cleaning and user maintenance shall not be made by

ÂÂ Never leave the appliance unattended when in use. Boil over causes smoking

children without supervision.

and greasy spillovers that may ignite.

ÂÂ

WARNING: Unattended cooking on a hob with fat or oil can be dangerous

ÂÂ

Never use your appliance as a work or storage surface.

and may result in fire. NEVER try to extinguish a fire with water, but switch off the

ÂÂ

Never leave any objects or utensils on the appliance.

appliance and then cover flame e.g.with a lid or a fire blanket.

4

5

Technical passporT

english

english

Technical passporT

electric hob

part 2. inStaLLatiOn

installation instructions

the appliance must be installed and connected in accordance with current regulations.

after unpacking the appliance, ensure there is no visible damage. if it has been damaged during transit, dO nOt USe, contact where you buy immediately.

Selection of installation equipment

BCut out the work surface according to the sizes shown in the drawing.

BFor the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.

BBe sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid larger deformation caused by the heat radiation from the hotplate.

detail as shown below:

	Model	L(mm)	W(mm)	H(mm)	D(mm)	A(mm)	B(mm)	X(mm)
	30cm ceramic hob	288	520	52	48	265+5	495+5	50 mini
						-0	-0
	30cm induction	288	520	56	52	265+5	495+5	50 mini
	hob					-0	-0
	60cm ceramic hob	590	520	52	48	555+5	495+5	50 mini
						-0	-0
	60cm induction	590	520	56	52	555+5	495+5	50 mini
	hob					-0	-0

electric hob

Under any circumstances, make sure the electric hob is well ventilated and the air inlet and outlet are not blocked. Ensure the electric hob is in good work state. As shown below:

nOte: The safety distance between the hotplate and the cupboard above the hotplate should be at least 760mm.

A(mm)	B(mm)	C(mm)	D	E
760mm	50mm minimal	20mm minimal	Air intake	Air exit 5mm

Before locating the fi xing brackets

The unit should be placed on a stable, smooth surface (use the packaging). Do not apply force onto the controls protruding from the hob.

easy fit kits

There is one easy fi t kits package for each hob, include fi xing clips and screws

(for ceramic hob there are total 2pcs clip and 2pcs screw, for induction hob there are total 4pcs clip and 4pcs screw).Find the easy fi t kit package fi rst.

Fix clips to hob: Insert the fi xing clip into fi xing hole reserved on sides of housing,fi x clip to housing with screw,then insert hob into cabinet/work surface.

6

7

Technical passporT

english

english

Technical passporT

electric hob

Fix hob to cabinet: Insert the hob into the cabinet/work surface as below diagrams, the mounted clips on the sides can secure your hob sturdily.

connecting the hob to the mains power supply

The power supply should be connected in compliance with the relevant standard, or a single-pole circuit breaker. the appliance have a large power rating and must be connected to electricity by a Qualifi ed Electrician.

nOteS:

1.If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools, so as to avoid any accidents.

2.If the appliance is being connected directly to the mains supply, an omni polar circuit breaker must be installed with a minimum gap of 3mm between the contacts.

3.The installer must ensure that the correct electrical connection has been made and that it complies with safety regulations.

4.The cable must not be bent or compressed.

5.The cable must be checked regularly and only replaced by qualifi ed technician.

the method of connections shown below.

electric hob

cautions

1.The hob must be installed by qualifi ed personnel or technicians.Please never conduct the operation by yourself.

2.The electric hob shall not be mounted to cooling equipment, dishwashers and rotary dryers.

3.The electric hob shall be installed such that better heat radiation can be ensured to enhance its reliability.

4.The wall and induced heating zone above the work surface shall withstand heat.

5.To avoid any damage, the sandwich layer and adhesive must be heat resistant.

6.A steam cleaner is not to be used.

7.This electric hob can be connected only to a supply with system impedance no more than 0.427 ohm. In case necessary, please consult your supply authority for system impedance information.

part 3. OperatiOn inStrUctiOnS product Overview

(1) model: ecO 301

1. 1800W Cooking Zone

2. 1200W Cooking Zone

3. Glass plate

4. Control panel

control panel

1. Cooking Zone selection button

2. Timer control button

3. Child Lock control button

4. Stop & Go control button

5.Heating level/Timer“-”button

6.Heating level/Timer“+”button

7.ON/OFF button

8

9

Technical passport

English

English

Technical passport

Electric Hob

(2)Model: ECO 601/ECO 601 C/ECO 601 Gr

1.1200W Cooking Zone

2.1800W Cooking Zone

3.1800W Cooking Zone

4.1200W Cooking Zone

5.Glass plate

6.Control panel

Control Panel

1. Cooking Zone selection button

2. Timer control button

3. Child Lock control button

4. Stop & Go control button

5.Heating level/Timer“-”button

6.Heating level/Timer“+”button

7.ON/OFF button

(3)Model: ECS 603/ECS 603 C/ECS 603 Gr

1.1200W Cooking Zone

2.2300W/1500W/700WTriple Cooking

Zone

3.1800W Cooking Zone

4.1200W Cooking Zone

5.Glass plate

6.Control panel

Electric Hob

Control Panel

1. Extened zone control button

2. Cooking Zone selection button

3. Child Lock control button

4. Stop & Go control button

5. Timer control button

6.Heating level/Timer slider control

7.ON/OFF button

(4)Model: ICS 604/ICS 604 C/ICS 604 Gr

1.1500W boost 2000W Cooking Zone

2.2000W boost 3000W Cooking Zone

3.2000W boost 3000W Cooking Zone

4.1500W boost 2000W Cooking Zone

5.Glass plate

6.Control panel

Control Panel

1. Booster function control button

2. Cooking Zone selection button

3. Child Lock control button

4. Stop & Go control button

5. Timer control button

6.Heating level/Timer slider control

7.ON/OFF button

10

11

Technical passport

English

English

Technical passport

Electric Hob

Notes: Product diagrams in this instruction manual for reference only, there might be slightly difference due to continually product improvements.

Before using your New Hob

ÂÂ Read this guide, taking special note of the ‘Safety Warnings’ section.

ÂÂ Remove any protective film that may still be on your new electric hob.

Using the Touch Controls

ÂÂ The controls respond to touch, so you don’t need to apply any pressure.

ÂÂ Use the ball of your finger,not its tip.

ÂÂ You will hear a beep each time a touch is registered.

ÂÂ Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.Even a thin film of water may make the controls difficult to operate.

Choose the right Cookware

ÂÂ Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the packaging or on the bottom of the pan.

ÂÂ You can check whether your cookware is suitable by carrying out a magnet test. Move a magnet towards the base of the pan. If it is attracted, the pan is suitable for induction hob.

ÂÂ If you do not have a magnet:

1.Put some water in the pan you want to check.

2.If does not flash in the display and the water is heating,the pan is suitable.

ÂÂ Cookware made from the following materials is not suitable for an induction

hob: pure stainless steel, aluminum or copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Electric Hob

ÂÂ Induction hob are made from smooth, ceramic glass, the heat comes from a magnetic induction coil which heats the cookware but not the cooking surface. The heat from the cookware is transferred to the food.

ÂÂ It’s important that you use only metal pans specifically designed and/or approved for use on induction hobs. Never allow melamine or plastic containers to come in contact with the heat zones.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth,sits flat against the glass,and is the same size as the cooking zone. If you use smaller pot efficiency could be less than expected. Always centre your pan on the cooking zone.

Always lift pans off the electric hob – do not slide, or they may scratch the glass.

Notes: You can use any kind of pot or pan for Ceramic Hob. Make sure that base of your pot or pan is smooth,sits flat against the ceramicglass,and same size as the cooking zone for better cooking performance.

Using your Hob To start cooking

1. After the hob be connected to electricity and power on. Press and hold the ON/OFF control button for about 3 seconds till you hear a “beep” to turn the hob on. Now the hob enters into Standby mode, all heat setting indicators and

Timer setting indicators shows“-”

12

13

Technical passport

English

English

Technical passport

Electric Hob

2.Place a suitable pan on the cooking zone that you wish to use.

ÂÂ Make sure the bottom of the pan and the surface of the cooking zone are clean and dry.

3.Touching the heating zone selection control button

to select and active the cooking zone you wish to use.

The heat setting indicator of the selected zone will flash when be active.

4. Then set heating level of cooking zone

1) Touch control models:

ÂÂ Set heat setting by touching the or button. ÂÂ If press and hold either of the two buttons, the

value will adjust down or up rapidly, from 0 to 9 in circle.

2) Slider Touch control models:

ÂÂ For the model with a touch slider control, you can adjust heat setting by touching the slider control.

Notes:

1.After connect to electricity, when power on, the buzzer of hob beeps once, all indicators light up for 1 second then go out.

2.When the hob in Standby mode, if there is no practice within 1 minute, the electric hob will auto turn off, with buzzer beeps once.

3.To turn on hob, press the ON/OFF control button and hold on for about 3 seconds; To turn it off,just need to press ON/OFF button again.

4.You can modify the heat setting at any time during cooking.

5.The default setting of power level is 5, and power level can be adjusted from 0 to 9.The heating element will turn off under power level 0,with indicator shows“-”

6.The heat setting indicator of the selected zone will flash when adjusting. After adjusting,the number in indicator will flash for 5 seconds and then stop flash, then the setting be confirmed.

Electric Hob

To turn off hob

1.Touch heating zone selection control button, then turn the cooking zone off by touching or control button adjust heat setting to 0 level,which indicator shows“-“.

2.You can also turn the whole hob off by touching the ON/OFF control button.

Note: The Timer/Minute Reminder setting will be canceled if hob be turn off.

Note: If there is power cut off during cooking, all programmer setting will be cancelled, you need to reset the programmer again.

Note: The cooling fan of induction hob will remain on for about 1 minute after the hob be turned off.

Beware of hot surfaces

After turn off, the letter ”H” will show in the power setting indicator which cooking zone is hot to touch. It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate that is still hot.

When in Standby mode, if the surface of cooking zone is hot to touch, the letter

“H”and“-”will show in its heat setting indicator alternately.

Using Large Heating Area-Ceramic Hob

Some of ceramic hob models might have one or several extended cooking zones

(Oval/Dual/Triple zone),these extended zones can provide larger cooking area and additional heat. To active the extended zone, please follows below:

1.Turn on the hob by touch ON/OFF control button.

2.Select the cooking zone which has extended zones, by touch the heating zone selection button of it. Then adjust the heat setting of it, the central zone will switch on.

3.Touch the extended zone control button to active extended heating element to get a large heating area.

Notes:

1. By continuous touch the control button, the extended zone work at below consequence:

-Oval zone:“Central-Oval-Central-Oval-Central zone…”

-Dual zone:“Central-Dual-Central-Dual-Central zone…”

-Triple zone: “Central-Dual-Triple-Central-Dual-Triple- Central zone…”

14

15

Technical passporT

english

english

Technical passporT

electric hob

2. When Oval Zone or Dual Zone active, the LED indicator of it will show heat setting and “ “ alternately ; When Triple Zone active, the LED indicator of it will show power setting and“”alternately.

Using Booster function-induction Hob

Some of induction hob models might have one or several cooking zones which has Booster function.You can use the“Booster”function to boost power of relevant cooking zone for a maximum power rating for 5 minutes. This function could reduce the cooking time, which convenience for cooking when in hurry!

to use booster function when induction hob is working, follows below:

1. Touch the heating zone selection control button to select the cooking zone you want to use boost function.

2. Touch the Booster function control button

, the heating zone indicator will show “b” and fl ashing for 5 seconds then stop fl ashing. Then Booster function be actived, the power reach Max for 5 minutes, and then return to the pre-set heat setting.

note:

1.When using booster function, if the other cooking zone in vertical direction also working meanwhile power setting higher than level 2, programmer will auto turn power setting of the other cooking zone to level 2.

2.After booster fi nish,the cooking zone will return to original setting.

cancel the Booster function

1. Touching the heating zone selection control that you wish to cancel the booster function

2. Touching the «Booster» control to cancel the Booster function, then the cooking zone will revert to its original setting.

cHiLd LOck Safety cOntrOL

 You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on) by active Child Lock function.

electric hob

 When the controls are locked, except the ON/OFF control button and Child

Lock control button, all other touch control buttons are disabled. to lock the controls

Touch the Child Lock control button once .The timer indicator will show “ Lo“,and Child Lock function be active.

to unlock the controls

1. Make sure the electric hob is turned on.
2. Touch and hold the Child Lock control button		for 3 seconds, the buzzer
beeps once and“Lo”disappears in timer indicator,the Child Lock be inactive.
3. You can now start using your electric hob.
Under the child lockmode,all controls button are disable except theON/OFF
and child lock	.

You can always turn the hob off with the ON/OFF control in an emergency, but you shall unlock the hob fi rst in the next operation

note: Under Child Lock function, if turn the hob off without inactive the Child Lock function. When turn on the hob later, the Child Lock function will still valid.

Stop & Go function

Âmake cooking easy! When cooking, your doorbell rings, phone rings, or kid shouts from another door. Need to step out of kitchen? These means dinner could burn, or take longer time to ready if you switch everything off.

ÂThe Stop & Go function can turn off all zones. When you back, with one more

touching of the button , hob restarts where they were, to carry on cooking.

1. active Stop & Go function

To active Stop & Go function, you can press the Stop & Go function button once. Then all programmer setting be hold on and hob stop heating, all heat setting indicators show“P”.

2. inactive Stop & Go function

To cancel Stop & Go function, you can press the Stop & Go function again, after come back. Then all programmer setting will return to what they were, Stop & Go indicator“P”disappear from all indicators.

When Stop & Go function active,all control buttons are disable except the ON/

Off and Stop & Go button.

note: The hob will auto turn off, if Stop & Go function last more than 10 minutes.

16

17

Technical passport

English

English

Technical passport

Electric Hob

Using the Timer

You can use the timer in two different ways:

ÂÂ You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is up.

ÂÂ You can set it to turn either or more than one cooking zones off.

ÂÂ You can set the minute minder/timer for up to 99 minutes.

Timer overview	Minute display
	shows the number
	of minutes

Timer control

Using the Timer as a Minute Minder

If you have not selected any cooking zones

1. Make sure the hob is turned on.
2. Touch the timer control button	, the number in timer
indicator flashing.
3. Then adjust Minute Minder setting

1) Touch control models:

ÂÂ Set heat setting by touching the or button.

ÂÂ If press and hold either of the two buttons, the value will adjust down or up rapidly in circle.

Note: When the timer indicator flashing,touch timer control button another time,can quick confirm the timer setting.

2) Slider Touch control models:

ÂÂ Touch the timer control button once, the number of single digit in timer indicator flashing,then adjust single digit of minute minder setting by sliding the slider control.

ÂÂ Press the timer control button again, the number of tens digit in timer indicator flashing, then adjust tens digit of minute minder setting by sliding the slider control.

Electric Hob

Note: By continuous touch the timer control button, the slider works at below consequence:“Single Digit-Tens Digit-Confirm Setting-Single Digit-…”

Note: After adjusting, the setting in timer indicator will flash for 5 seconds and then stop flashing,then the setting be confirmed.

Note: The default setting of Minute Reminder is 30 minutes.

4.When the minute minder is set, it will begin to count down immediately, the display will show the remaining time.

5.Buzzer will beep for 30 seconds and timer indicator shows

“- - “when the setting time finished. Any efficient touching of control buttons during it, would end up the buzzer beeps.

Setting the timer to turn cooking zone off

1. Touch the heating zone selection control button to select the cooking zone you wish to set timer for.

2. Touch the timer control button	, the number in timer
indicator flashing.

3.Then adjust Minute Minder setting

1)Touch control models:

ÂÂ Set heat setting by touching the or button.

ÂÂ If press and hold either of the two buttons, the value will adjust down or up rapidly in circle.

Note: When the timer indicator flashing, touch timer control button another time,can quick confirm the timer setting.

2) Slider Touch control models:

ÂÂ Touch the timer control button ,once, the number of single digit in timer indicator flashing,then adjust single digit of minute minder setting by sliding the slider control.

ÂÂ Press the timer control button again, the number of tens digit in timer indicator flashing, then adjust tens digit of minute minder setting by sliding the slider control.

18

19