KTM EXC-F, 250 XC-F, EXC-F 400 XC-W, XCF-W, 400 XC-W User Manual

...
0 (0)
250 XC-F, XCF-W, EXC-F
400 XC-W, EXC RACING
525 XC, XC-W, EXC RACING
525 XC DESERT RACING
OWNER’S MANUAL 2007
ART. NR. 3.211.145 EN
ENGLISH
ENGLISH
1
INTRODUCTION »
Please insert the serial numbers of your motorcycle in the boxes below
Frame number
Engine number
Key number
Stamp of dealer
All information contained is without obligation. KTM-Sportmotorcycle AG particularly reserves the right
to modify any equipment, technical specifications, prices, colors, shapes, materials, services, service work,
constructions, equipment and the like so as to adapt them to local conditions or to cancel any of the
above items, all without previous announcement and without giving reasons. KTM may stop manufactur-
ing certain models without previous notice. KTM shall not be held liable for any deviations of availabil-
ity and/or ability to deliver, illustrations, descriptions, printing and/or other errors. The illustrated models
partly contain extra equipment, which is not applied to standard models.
© 2006 by KTM-SPORTMOTORCYCLE AG, Mattighofen AUSTRIA; All rights reserved; Reprint, also in
extracts, with written allowance of KTM-SPORTMOTORCYCLE AG, Mattighofen only.
We would like to congratulate you on your purchase of a KTM motorcycle.
You are now the owner of a state-of-the-art sport motorcycle that guarantees to bring you lots of fun and
enjoyment, provided that you clean and maintain it appropriately.
COMSUMER INFORMATION FOR AUSTRALIA ONLY
Tampering with noise control system prohibited
Owners are warned that the law may prohibit:
(a) The removal or rendering inoperative by any person other than for purposes of maintenance, repair or
replacement, of any device or element of design incorporated into any new vehicle for the purpose of
noise control prior to its sale or delivery to the ultimate purchaser or while it is in use; and
(b) the use of the vehicle after such device or element of design has been removed or rendered inopera-
tive by any person.
In accordance with the international quality management ISO 9001 standard, KTM uses
quality assurance processes that lead to the highest possible product quality.
ENGLISH
2
IMPORTANT INFORMATION »
INTENDED PURPOSE
KTM sports motorcycles are designed and constructed to resist the usual wear and tear of normal use in
competitions.
The motorcycles comply with the regulations and categories currently in effect with the leading interna-
tional motorcycle associations.
The XC and other „competition only“ labeled models are prohibited on public roads.
„On the road“ approved models are only allowed on public roads in the original homologated (throttled)
version. Without this performance restriction (i.e. de-throttled), these models are only allowed to be driven
off-road and not
on public roads.
The EXC models are designed for off-road sports endurance competitions(enduro) and not
suitable for
predominant motocross use.
NOTE: The above is a general statement. Specific limited warranty and limited guarantee information
may vary depending upon distribution. Please check with your local KTM dealer for limited warranty and
limited guarantee information specific to your KTM model and region.
OWNER’S MANUAL
Please read this manual carefully and completely before going on your first ride. It contains a great deal
of information and advice which will help you use and handle your bike properly. Only by doing so will
you learn how to tune your motorcycle to your specific needs and how to protect yourself against injury.
Besides, this manual contains important information on motorcycle maintenance.
In your own interest, please pay particular attention to notices that are marked as follows:
At the time this manual was typeset, it was up-to-date with the latest state of this production series. It
cannot be completely ruled out, however, that minor discrepancies may exist resulting from further design
upgrades of these motorcycles.This manual is an important part of your motorcycle and should be passed
on to any subsequent owner in case you decide to sell it.
SERVICE
Observance of the service, maintenance and tuning instructions for the engine and chassis specified in
the Owner's Manual is a prerequisite for faultless operation and the avoidance of premature wear. An
improperly tuned chassis can lead to damage and breakage of the chassis components (see chapter on
checking the basic chassis setting).
The use of the motorcycle under extreme conditions, e.g. on extremely muddy and wet terrain, can lead
to higher than average wear on components such as the drive train or the brakes. In this case it may
become necessary to service or replace wear parts before the service limit specified in the maintenance
schedule has been reached.
Ignoring these instructions can be dangerous to life and limb!
Ignoring these instructions may damage parts of the motorcycle or impair the motorcycle's
traffic safety!
ENGLISH
3
IMPORTANT INFORMATION »
We expressly point out that work marked with an asterisk in the chapter „Maintenance work on the chas-
sis and engine“ must be performed. If maintenance work should become necessary during a competition
it should be performed by a trained mechanic. KTM strongly recommends that all service work to your
KTM should be performed by a qualified KTM dealer.
Take special care to follow the recommended run in, inspection, and maintenance intervals. Heeding
these guidelines will significantly increase the life of your motorcycle.
WARRANTY
The service work specified in the „Lubrication and Maintenance Schedule“ must be performed and serv-
ice records must be kept for warranty documentation. Lack of proper service and maintenance records or
documentation could void warranty.
No claims can be filed under the warranty for damage or consequential damage caused by manipulations
or conversions to the motorcycle.
AUTOMOTIVE FLUIDS
The fuels and lubricants specified in the Owner's Manual or fluids with equivalent specifications must
be used in accordance with the maintenance schedule.
SPARE PARTS, ACCESSORIES
For your own safety, use KTM-approved parts and accessories only. KTM is not liable for damage that
arises in connection with the use of other products.
TRANPORT
When transporting your KTM, ensure that it is held upright with restraining straps or other mechanical
fastening devices and that the fuel tap is in the OFF position - if the motorcycle should fall over, no fuel
can leak from the carburetor or fuel tank
ENVIRONMENT
Off-road motorcycle driving is a wonderful sport and we hope that you will be able to enjoy it to the full.
It may, however, involve potential problems for the environment or lead to conflicts with others. These
problems or conflicts can be avoided if the motorcycle is used responsibly. To safeguard the future of
motorcycle sports, make sure that you use the motorcycle in accordance with the law, show that you are
environmentally conscious and respect the rights of others.
We wish you a lot of fun when driving !
KTM-SPORTMOTORCYCLE AG
5230 MATTIGHOFEN, AUSTRIA
Attachments: 1 spare parts manual chassis & engine
TABLE OF CONTENTS »
ENGLISH
4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . .2
SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . .5
Engine number, engine type . . . . . . . . . . . . . . . . . . . . . .5
Chassis number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION INSTRUMENTS . . . . . . . . . . . . . . . . . . . . . . . .6
Clutch lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Hand brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Short circuit button (XC) . . . . . . . . . . . . . . . . . . . . . . . . .6
Combination switch (EXC) . . . . . . . . . . . . . . . . . . . . . . . .6
Headlamp switch (XC-W) . . . . . . . . . . . . . . . . . . . . . . . . .7
Flasher switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Starter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Emergency OFF switch (EXC Australia) . . . . . . . . . . . . . . .7
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Electronic speedometer . . . . . . . . . . . . . . . . . . . . . . . . . .8
Activating and deactivating display modes . . . . . . . . . . . .9
Overview of the electronic speedometer functions . . . . . .12
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Filler cap (bayonet cap) . . . . . . . . . . . . . . . . . . . . . . . . .13
Filler cap (screw cap) . . . . . . . . . . . . . . . . . . . . . . . . . .13
Fuel tap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Choke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Shift lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Kickstarter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Foot brake pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Side stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Compression damping of fork . . . . . . . . . . . . . . . . . . . .15
Rebound damping of fork . . . . . . . . . . . . . . . . . . . . . . .15
Compression damping of shock absorber
(XC, EXC SIXDAYS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Compression damping of shock absorber (XC-W, EXC) . . .16
Rebound damping of shock absorber . . . . . . . . . . . . . . .16
GENERAL TIPS AND WARNINGS FOR STARTING
THE MOTORCYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Instructions for initial operation . . . . . . . . . . . . . . . . . . .17
Running in the XC/EXC models . . . . . . . . . . . . . . . . . . .17
DRIVING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .18
Check the following before each start . . . . . . . . . . . . . . .18
Starting when the engine is cold . . . . . . . . . . . . . . . . . .18
Starting when the engine is warm . . . . . . . . . . . . . . . . .19
What to do when the engine is „flooded“ . . . . . . . . . . . .19
Starting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Shifting/Riding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Stopping and parking . . . . . . . . . . . . . . . . . . . . . . . . . .20
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PERIODIC MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . .21
MAINTENANCE WORK ON CHASSIS AND ENGINE . . . . . . .27
Changing the spring preloading of the shock absorber . . .27
Pivot bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Basic suspension setup for the weight of the driver . . . . .28
Checking the shock absorber and spring . . . . . . . . . . . . .28
Determining the static sag of the shock absorber . . . . . . .28
Determining the riding sag of the shock absorber . . . . . . .28
Checking the basic setup of the telescopic fork . . . . . . . .29
Changing the spring preload on the telescopic fork
(XC, EXC SIXDAYS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Changing the spring preload on the telescopic fork
(XC-W/EXC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Replacing fork springs . . . . . . . . . . . . . . . . . . . . . . . . .29
Breather plug front fork . . . . . . . . . . . . . . . . . . . . . . . . .30
Cleaning the dust sleeves of the telescopic fork . . . . . . . .30
Checking and adjusting the steering head bearing . . . . .30
Changing the fork offset (caster) (XC, EXC SIXDAYS) . . . .31
How to change the handlebar position . . . . . . . . . . . . . .32
Check chain tension . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Correct chain tension . . . . . . . . . . . . . . . . . . . . . . . . . .33
Chain maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Chain wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
General information about KTM disc brakes . . . . . . . . . .35
Adjusting the free travel at the hand brake lever . . . . . . .36
Checking the brake fluid level - front brake . . . . . . . . . . .36
Refilling the front brake fluid reservoir . . . . . . . . . . . . . .36
Checking the front brake pads . . . . . . . . . . . . . . . . . . . .36
Replacing the front brake pads . . . . . . . . . . . . . . . . . . .37
Changing the basic position of the foot brake pedal . . . . .37
Checking the rear brake fluid level . . . . . . . . . . . . . . . . .37
Refilling the rear brake fluid reservoir . . . . . . . . . . . . . . .37
Checking the rear brake pads . . . . . . . . . . . . . . . . . . . . .38
Replacing the rear brake pads . . . . . . . . . . . . . . . . . . . .38
Dismounting and mounting the front wheel . . . . . . . . . . .38
Dismounting and mounting the rear wheel . . . . . . . . . . .39
Checking spoke tension . . . . . . . . . . . . . . . . . . . . . . . . .39
Tires, air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Check/set distance of the magnetic sensor . . . . . . . . . . .40
Replacing the battery of the digital speedometer . . . . . . .40
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Replacing headlight lamp/parking light lamp . . . . . . . . . .42
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Checking the coolant level . . . . . . . . . . . . . . . . . . . . . . .43
Bleeding the cooling system (400/450/525) . . . . . . . . . .43
Bleeding the cooling system (250-F) . . . . . . . . . . . . . . .44
Replacing the glassfiber yarn packing of the silencer . . . .44
Cleaning the spark arrester (XC-W USA) . . . . . . . . . . . . .44
Cleaning the air filter . . . . . . . . . . . . . . . . . . . . . . . . . .45
Adjusting the throttle cables . . . . . . . . . . . . . . . . . . . . .45
Changing the original position of the clutch lever . . . . . . .46
Checking the oil level of the hydraulic clutch
(400/450/525) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Checking the oil level of the hydraulic clutch (250-F) . . .46
Bleeding of the hydraulic clutch . . . . . . . . . . . . . . . . . .46
Carburetor – Adjust idling (Keihin-FCRMX 37/39/41) . . . .47
Basic information on carburetor wear . . . . . . . . . . . . . . .47
Adjusting the mixture control screw . . . . . . . . . . . . . . . .47
Checking the float level (float height) . . . . . . . . . . . . . . .47
Draining the float chamber of the carburetor . . . . . . . . . .48
Oil circuit (400/450/525) . . . . . . . . . . . . . . . . . . . . . . .48
Oil circuit (250-F) . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Checking the engine oil level . . . . . . . . . . . . . . . . . . . . .48
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Changing the engine oil . . . . . . . . . . . . . . . . . . . . . . . .49
Changing the oil filters . . . . . . . . . . . . . . . . . . . . . . . . .50
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
CONSERVATION FOR WINTER OPERATION . . . . . . . . . . . .53
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
USE AFTER A PERIOD OF STORAGE . . . . . . . . . . . . . . . . .53
TECHNICAL DATA – ENGINE . . . . . . . . . . . . . . . . . . . . . . .54
TECHNICAL DATA – CHASSIS . . . . . . . . . . . . . . . . . . . . . .59
HEAD WORD INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . .appendix
Page Page
SERIAL NUMBER LOCATIONS »
Chassis number
The chassis number is stamped on the right side of the steering head tube.
Enter this number in the field on page no 1.
Engine number, engine type
The engine number and the engine type are stamped into the left side of the
engine below the engine sprocket. Enter this number on page 1.
ENGLISH
5
A
B
C
OPERATION INSTRUMENTS »
Hand brake lever
The hand brake lever [3] is mounted on the handlebars on the right and
actuates the front wheel brake. The adjusting screw [B] can be used to change
the basic position of the hand brake lever (see "Maintenance").
Combination switch (EXC)
The light switch has 2, respectively 3 switch positions.
[A] = Light off (this function is not available in all models)
[B] = Low beam on
[C] = High beam on
You may use button [5] to actuate the horn.
The red short circuit button [6] serves to switch off the engine. Leave the
switch pressed until the engine stops.
3
B
4
Short circuit button (XC)
The short circuit button [4] turns off the engine. When pressing this button,
the ignition circuit is short-circuited.
ENGLISH
6
56
Clutch lever
The clutch lever [1] is located on the left side of the handlebar. The adjust-
ing screw [A] is used to change the original position of the clutch lever (see
maintenance work on chassis and engine).
The clutch is hydraulically actuated and adjusts itself automatically.
1
A
OPERATION INSTRUMENTS »
Headlamp switch (XC-W)
In this model the headlamp is switched on with the pull switch [1].
Flasher switch
The flasher switch is a separate unit and is mounted on the left portion of the
handlebar.
The wire harness is designed in a way that whenever you want to use your
bike off-road, you can dismount the entire turn indicator system without
affecting the function of the remaining electrical system.
Flasher left
Flasher right
Starter button
Pushing the black starter button [2] will actuate the E-starter.
Indicator lamps
The green control lamp [5] flashes in the same rhythm as the flash-
ing indicator when the indicator is working.
The blue control lamp [6] lights up when the high beam is on.
ENGLISH
7
2
Emergency OFF switch (EXC Australia)
The red emergency-OFF switch [3] is arranged adjacent to the throttle grip.
In this position, the E-starter is operational and the engine can
be started.
In this position, the E-starter and ignition circuits are
interrupted.The E-starter cannot be actuated, and the engine will
not start, not even if you attempt to start it with the kickstarter.
Pushing the black starter button [4] will actuate the E-starter.
3
4
5
6
1
OPERATION INSTRUMENTS »
ENGLISH
8
TEST
All of the display segments briefly light up for the display function test.
WS (wheel size)
The display changes and the circumference of the front wheel is briefly dis-
played in millimeters (2205 mm corresponds to a front wheel circumference
of 21" with production tires).
Afterwards the display will return to the previous display mode.
Electronic speedometer
The display in the electronic speedometer is activated as soon as you press
a button on the speedometer or an impulse is received from the wheel sen-
sor. The display lights up when the engine is running.
The display is cleared if no button is pressed for 1 minute or no impulse is
received from the wheel sensor.
The | button is used to change between display modes.
The + and buttons are used to control various functions.
SPEED display mode / H (service hours)
Only the SPEED / H and SPEED / ODO display modes are activated in the
condition at delivery. SPEED/H is displayed whenever the display is activated
and the front wheel is not turning. It automatically changes to the SPEED/ODO
display mode as soon as the front wheel starts turning.
SPEED displays the speed.
H displays the engine's service hours. The service hour counter starts to count
as soon as you start the engine. The displayed figure cannot be changed.
Service intervals are indicated in service hours for some KTM offroad motor-
cycles, making the service hour counter a very practical function.
SPEED / ODO display mode (odometer)
The SPEED/ODO mode displays the speed and the total distance traveled.
The display automatically changes to the SPEED/H display mode when the
front wheel stops turning.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. changes to the next display mode
The electronic speedometer has a number of display modes (functions) that
you can also activate (reveal) (see: Activating and deactivating display modes).
OPERATION INSTRUMENTS »
ENGLISH
9
SPEED / LAP (lap time) display mode
You can use the manual stop watch to stop and store up to 10 lap times,
which you can view in the LAP/LAP display mode (see below).
LAP displays the lap times in hours, minutes and seconds.
+ button Starts and stops the stop watch, lap time is not
reset to 0
button Stops the stop watch, stores the lap time and restarts
the stop watch again. The time is reset to 0. A total
of 10 lap times can be stored. If the lap time con-
tinues to run after you press the - button, all 10 mem-
ory locations are occupied.To clear all of the stored
lap times, hold the | button for 3 seconds in the
SPEED/LAP mode.Up to 10 lap times can be stored
in this way.
briefly press | button Changes to the next display mode.If no lap time is
stored or the motorcycle is driving, the LAP/LAP
mode will be skipped.
hold | button 3 secs. Clears all LAP figures
SPEED / CLK (time) display mode
CLK displays the time in hours, minutes and seconds.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. set the clock menu
To set the clock, see „Setting the clock“.
Activating and deactivating display modes
In the display mode SPEED/H, press and hold the | button for 3 seconds to
access the SETUP menu. The active functions will be displayed. The blink-
ing function can be activated by pressing the + button and deactivated by
pressing the button.
Press and hold the | button 3 seconds to store the settings.
If no button is pressed for 20 seconds, the setting will be stored automati-
cally and the display will return to the SPEED/H mode.
+ button activates the blinking display
button deactivates the blinking display
briefly press | button changes to the next display without changing any
settings
hold | button 3 secs. starts the SETUP
stores the settings and changes to the SPEED/H
mode
The following display modes can be activated:
TR1 tripmaster 1
TR2 tripmaster 2
A1 average speed 1
A2 average speed 2
S1 stop watch 1
S2 stop watch 2
CLK clock
LAP lap time
MAX maximum speed
KMH/MPH display in kilometers or miles (see: Kilometers or miles)
If you have activated all of the display modes, they will be displayed in the
following order:
SPEED/H, SPEED/CLK, SPEED/LAP, LAP/LAP, SPEED/MAX, SPEED/ODO,
SPEED/TR1, SPEED/TR2, SPEED/A1, SPEED/A2, SPEED/S1, SPEED/S2
OPERATION INSTRUMENTS »
ENGLISH
10
LAP / LAP display mode (to view lap times)
The LAP/LAP display mode will only be shown if lap times have been stored
and the front wheel has stopped. It will display the lap number and the
stopped lap time in hours, minutes and seconds. Press the + button to access
the next lap time.
To clear all of the stored lap times, hold the | button for 3 seconds in the
SPEED/LAP mode.
+ button changes to the next lap time
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. changes to the next display mode
SPEED / MAX display mode (maximum speed)
MAX displays the maximum speed traveled and is always active.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. clears the MAX figure
SPEED / TR1 display mode (tripmaster 1)
The TR1 tripmaster is always active and counts to 999.9. It is used to meas-
ure the length of a trip or the distance between 2 refueling stops.
TR1 is linked to A1 (average speed 1). The calculation of these figures is acti-
vated by the first impulse received from the wheel sensor (when the front wheel
starts to turn) and stops 3 seconds after the last impulse is received (when
the front wheel has stopped).
The TR1, A1 and S1 figures are automatically cleared after passing 999.9.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. clears the TR1, S1, A1 figures
SPEED / TR2 display mode (tripmaster 2)
The tripmaster 2 is always active and counts to 999.9. Contrary to TR1, the
displayed figure can be changed using the + and buttons. This is a very use-
ful function for trips taken according to a roadbook.
+ button increases the TR2 figure
button decreases the TR2 figure
briefly press | button changes to the next display mode
hold | button 3 secs. clears the TR2 figure
SPEED / A1 display mode (average speed 1)
A1 shows the average speed based on the TR1 (tripmaster 1) and S1 (stop
watch 1) figures. The calculation of this figure is activated by the first impulse
received from the wheel sensor and stops 3 seconds after the last impulse is
received.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. clears the TR1, S1, A1 figures
OPERATION INSTRUMENTS »
ENGLISH
11
Kilometers or miles
The unit (kilometers or miles) can also be changed. The ODO figure will be
retained and converted accordingly. The TR1, A1, S1, TR2 and A2 figures
will be cleared.
To select the unit, select the SPEED/H mode and hold the | button for 3 sec-
onds to access the SETUP menu. Press the | button until the KMH/MPH
function blinks. Press the + button briefly to move to the options. Press the
+ button for KMH or the button for MPH.
To set, briefly press the | button 1 x and hold for 3 seconds until the dis-
play returns to the SPEED/H mode.
If no button is pressed for 20 seconds, the setting will be stored automati-
cally and the display will return to the SPEED/H mode.
+ button to access the menu
to activate the KMH display
button to activate the MPH display
briefly press | button changes to the next mode
changes from the menu to the SETUP menu
hold | button 3 secs. stores and closes the SETUP menu
SPEED / A2 display mode (average speed 2)
A2 shows the average speed based on the TR2 (tripmaster 2) and S2 (stop
watch 2) figures.
The displayed figure can deviate from the actual average speed if the TR2
figure was changed manually or if S2 was not stopped after the trip.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. changes to the next display mode
SPEED / S1 display mode (stop watch 1)
S1 shows the traveling time based on TR1 and continues to run whenever it
receives impulses from the wheel sensor. The calculation of this figure is acti-
vated by the first impulse received from the wheel sensor and stops 3 sec-
onds after the last impulse is received.
+ button no function
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. clears the TR1, S1, A1 figures
SPEED / S2 display mode (stop watch 2)
S2 is a manual stop watch. Start the stop watch by pressing the + button,
press again to hold. Press again to continue timing.
Press the | button to change to the next mode. The S2 display will blink in
the other modes if S2 continues to run in the background. To stop S2, return
to the SPEED/S2 mode and press the + button.
+ button starts and stops the stop watch
button no function
briefly press | button changes to the next display mode
hold | button 3 secs. clears the S2 figure
OPERATION INSTRUMENTS »
ENGLISH
12
Setting the clock
To set the clock, switch the ignition off and select the SPEED/CLK mode. Press
and hold the | button for 3 seconds. The blinking digits can be changed
using the + and - buttons. Press the | button to move to the next digit. 0-
12 will show the time in the 12-hour mode, 0-24 in the 24-hour mode.
Press and hold the | button for 3 seconds to store the settings.
If no button is pressed for 20 seconds, the settings will be stored automati-
cally and the display will return to the SPEED/CLK mode.
+ button time +
button time -
briefly press | button changes to the next digit
hold | button 3 secs. starts the SETUP menu
stores the time and changes to the SPEED/CLK dis-
play mode
If the CLK, LAP, MAX, TR1, TR2 A1, A2, S1 and S2 figures are suddenly cleared, the battery in the electronic speedometer is empty
and must be replaced (see: Replacing the battery in the electronic speedometer).
A tripmaster switch is available as an accessory that lets you control the electronic speedometer functions from the handlebar.
Motorcycle is standing
Motorcycle is driving
OVERVIEW OF THE ELECTRONIC SPEEDOMETER FUNCTIONS
display
briefly press + button
briefly press button
briefly press | button hold | button 3 secs.
X
SPEED / H
no function no function next display mode
displays the SETUP menu
X X
SPEED / CLK
no function no function next display mode Setting the clock menu
X X
SPEED / LAP
starts/stops LAP without
clearing LAP figure
stops LAP, stores LAP
figure, resets LAP to 0
next display mode clears all LAP figures
X
LAP / LAP
next figure no function next display mode next display mode
X X
SPEED / MAX
no function no function next display mode clears MAX
X
SPEED / ODO
no function no function next display mode next display mode
X X
SPEED / TR1
no function no function next display mode clears TR1, S1, A1
X X
SPEED / TR2
increases the TR2 figure reduces the TR2 figure next display mode clears TR2
X X
SPEED / A1
no function no function next display mode clears TR1, S1, A1
X X
SPEED / A2
no function no function next display mode next display mode
X X
SPEED / S1
no function no function next display mode clears TR1, S1, A1
X X
SPEED / S2
starts - stops S2 no function next display mode clears S2
OPERATION INSTRUMENTS »
ENGLISH
13
1
2
XC
EXC
Filler cap (bayonet cap)
To open the filler cap: Turn the filler cap 45° counter-clockwise.
To close the filler cap: Put the filler cap on and turn it 45 ° clockwise.
Filler cap (screw cap)
To open the filler cap: Turn the filler cap counter-clockwise.
To close the filler cap: Put the filler cap on and tighten it by turning it
clockwise.
Install the tank breather hose [1] without kinks.
Fuel tap
OFF In this position the fuel tap is closed. No fuel can flow to the
carburetor.
ON During operation the twist grip must be turned to ON. This means that
the fuel can flow to the carburetor. With the twist grip in this position
the tank will be emptied until only the reserve is left.
RES The reserve tank cannot be tapped until the rotating handle is turned
to the RES position. Fill the tank as soon as possible and remember to
turn the rotating handle back to the ON position so that you will have
backup fuel next time, too.
Reserve XC, XC-W, EXC . . . .1.0 l (0.3 US gallons)
Reserve XC Desert Racing . .2.0 l (0.6 US gallons)
Choke
If you pull the choke button [2] out as far as possible, a bore in the carbure-
tor will be opened through which the engine may take in additional fuel. The
result is a „fat“ fuel-air mixture of the type needed for cold starts.
To deactivate the choke, push the choke button back into its basic position.
OPERATION INSTRUMENTS »
ENGLISH
14
2,3,4 (5,6)
1
N
1
Shift lever
The shift lever is mounted on the left side of the engine. The position of the
gears is shown in the illustration. Neutral, or the idle speed, is located
between first and second gear.
Kickstarter
The kickstarter is mounted on the right side of the engine. Its upper part can
be swivelled.
Foot brake pedal
The foot brake pedal is located in front of the right footrest. Its basic position
can be adjusted to your seat position (see maintenance work).
Side stand
Push the side stand to the ground with your foot and load it with the motor-
cycle. Make sure that you put your bike on solid ground and in a secure posi-
tion. For off-road riding, you can use the rubber band [1] to additionally secure
the center stand in its folded-up position
Steering lock
The handlebar can be locked by means of the lock located on the steering
head. To lock it, turn handlebar all the way to the right, insert key, turn it to
left, press it in, turn it to right, and remove it.
Never leave the key inserted in the steering lock. If you turn the handlebar to
the left the key could get damaged.
1
2
2
3
3
5
6
4
OPERATION INSTRUMENTS »
ENGLISH
15
Compression damping of fork
Hydraulic compression damping determines the reaction when the fork is com-
pressed. The degree of compression can be adjusted with adjusting
screws at the bottom of the fork legs.Remove the protecting cap [1].
Turn the adjusting screws [2] clockwise to increase damping, turn it counter-
clockwise to reduce damping during compression.
STANDARD ADJUSTMENT
turn adjusting screw clockwise as far as it will go
turn it back by as many clicks as are specified for the relevant type of fork
WP 14187C04 . . . . . . . 20 clicks WP 14187C28 . . . . . . . 18 clicks
WP 14187C06 . . . . . . . 20 clicks WP 14187C29 . . . . . . . .18 clicks
Rebound damping of fork
Hydraulic rebound damping determines the reaction when the fork is
rebound. By turning the adjusting screw [3] (REB), the degree of damping of
the rebound can be adjusted. Turn the knob clockwise to increase damping,
turn it counterclockwise to reduce damping during rebounding.
STANDARD ADJUSTMENT
turn adjusting screw clockwise as far as it will go
turn it back by as many clicks as are specified for the relevant type of fork
WP 14187C04 . . . . . . . 20 clicks WP 14187C28 . . . . . . . 20 clicks
WP 14187C06 . . . . . . . 15 clicks WP 14187C29 . . . . . . . .20 clicks
Changing the spring preload on the telescopic fork (see page 29)
Compression damping of shock absorber
(XC, EXC SIXDAYS)
The shock absorber on these models can synchronize the compression damp-
ing in the low and high-speed range separately (Dual Compression Control).
Low and high speed refers to the movement of the shock absorber during com-
pression and not to the speed of the motorcycle.
The low and high-speed technology overlaps.
The low-speed setting is primarily for slow to normal shock absorber compres-
sion rates.
The high-speed setting is effective at fast compression rates.
Turning in a clockwise direction will increase the damping, turning
counterclockwise will decrease the damping.
STANDARD LOW-SPEED SETTING:
turn the adjusting screw [4] to the limit in a clockwise direction using a
screwdriver .
unscrew the respective number of clicks for the specific type of shock absorber
in a counterclockwise direction.
WP 12187C28 . . . . . . . 15 clicks
WP 12187C29 . . . . . . . 15 clicks
STANDARD HIGH-SPEED SETTING:
turn the adjusting screw [5] to the limit in a clockwise direction using a
box wrench.
unscrew the respective number of turns for the specific type of shock absorber
in a counterclockwise direction.
WP 12187C28 . . . . . . . . . . .1 turn
WP 12187C29 . . . . . . . . . . .1 turn
The damping unit of the shock absorber is filled with high-compression nitro-
gen. Never try to take the shock absorber apart or to do any maintenance work
yourself. Severe injuries could be the result.
Never unscrew the black screw connection [6] (24mm).
OPERATION INSTRUMENTS »
ENGLISH
16
2
1
4
3
Compression damping of shock absorber (XC-W, EXC)
The compression damping (during compression) can be adjusted for these
shock absorbers (Mono Compression Control).
The degree of damping can be adjusted by turning adjusting screw [1] with
a screwdriver. Turning in a clockwise direction will increase the damping, turn-
ing in a counterclockwise direction will decrease the damping.
STANDARD ADJUSTMENT:
turn the adjusting screw clockwise to the stop.
then turn the adjusting screw counterclockwise, counting the number of
clicks that corresponds to the respective type of shock absorber.
WP 12187C04 . . . . . . . 15 clicks
WP 12187C06 . . . . . . . 15 clicks
The damping unit of the shock absorber is filled with high-compression nitro-
gen. Never try to take the shock absorber apart or to do any maintenance work
yourself. Severe injuries could be the result.
Never unscrew the black screw connection [2] (24mm).
Rebound damping of shock absorber
By using the adjusting screw [3], the degree of damping of the rebound can
be adjusted. Turn the knob clockwise to increase damping, turn it counter-
clockwise to reduce damping during rebounding.
STANDARD ADJUSTMENT:
turn the adjusting screw clockwise to the stop.
then turn the adjusting screw counterclockwise, counting the number of
clicks that corresponds to the respective type of shock absorber.
WP 12187C04 . . . . . . . 25 clicks WP 12187C28 . . . . . . . 24 clicks
WP 12187C06 . . . . . . . 25 clicks WP 12187C29 . . . . . . . .24 clicks
The damping unit of the shock absorber is filled with high-compression nitro-
gen. Never try to take the shock absorber apart or to do any maintenance work
yourself. Severe injuries could be the result.
Never unscrew the black screw connection [4] (15mm).
GENERAL TIPS AND WARNINGS FOR STARTING THE MOTORCYCLE »
ENGLISH
17
Wear suitable clothing when driving a motorcycle. Clever KTM
drivers always wear a helmet, boots, gloves and a jacket, regard-
less of whether driving all day or just for a short trip. The
protective clothing should be brightly colored so that other
vehicles can see you as early as possible.
Always turn on the light to make sure that other drivers
become aware of you as early as possible.
Do not drive after having consumed alcohol.
Only use accessories recommended by KTM. For example,
front panelling can impair the driving properties of the motor-
cycle. Cases, extra tanks, etc. can alter the weight distribu-
tion and thus also impair the vehicles driving properties.
The front and rear wheel may only be fitted with tires that
have the same profile type.
The XC/EXC models are designed and dimensioned for 1 per-
son only. Never take another rider along.
Observe the traffic regulations, drive defensively and try to
look ahead as far as possible so that any hazards can be rec-
ognized as early as possible.
Adjust your driving speed according to the conditions and
your driving skills.
Drive carefully on unknown roads or on unfamiliar trials.
When driving off-road, always have a friend on a second motor-
cycle to keep you company, so that you can help each other
should difficulties arise.
Replace the helmet visor or goggle lens when scratched or
damaged. if bright light shines through a scratched visor or
lens, the operator will be blinded.
Never leave your motorcycle without supervision if the engine
is running.
The XC models are not approved for use on public roads and
freeways.
When riding your motorcycle, please bear in mind that other
people may feel molested by excessive noise.
Instructions for initial operation
Make sure the work for the „pre-delivery inspection“ was per-
formed by your authorized KTM workshop. The DELIVERY
CERTIFICATE and SERVICE MANUAL will be handed over
when you pick up your vehicle.
Read these operating instructions carefully before your first
ride.
Familiarize yourself with the operating elements.
Set the clutch lever, the handbrake lever, and the footbrake
pedal to the positions that are most convenient for you.
Get used to handling the motorcycle on an empty parking
lot or open space, before starting on a longer drive. Also try
to drive as slowly as possible and in a standing position, to
improve your feeling for the vehicle.
Do not drive along off-road tracks which go beyond your abitily
and experience.
Hold the handlebars with both hands and leave your feet on
the foot rests while driving.
Remove your foot from the foot brake lever when you are not
braking. If the foot brake lever is not released the brake
pads rub continuously and the braking system is
overheated.
Do not make any alterations to the motorcycle and always
use ORIGINAL KTM SPARE PARTS. Spare parts from other
manufacturers can impair the safety of the motorcycle.
Motorcycles are sensitive to alterations in the distribution of
weight. If you are taking luggage with you, this should be
secured as close as possible to the middle of the vehicle;
distribute the weight evenly between the front and rear wheel.
Never exceed the maximum permissible laden weight and
the axle weights. The maximum permissible laden weight is
comprised of the following components:
Motorcycle ready for operation and tank full
Luggage
Driver with protective clothing and helmet.
Pay attention to the running-in procedure.
Running in the XC/EXC models
Even very precisely machined sections of engine components
have rougher surfaces than components which have been slid-
ing across one another for quite some time. Therefore, every engine
needs to be broken in.
For this reason, do not load the engine more than 50% of its
capacity during the first 3 operating hours. Besides, the engine
speed must not exceed 7000 rpm. Avoid going full-throttle!
In the following 12 operating hours, you may load the engine
up to 75% of its capacity. Use the motorcycle on various types
of terrain (road, easy off-road trails).
The XC/EXC models were uncompromisingly designed for off-
road competition purposes only. “On the road“ approved mod-
els are only allowed on public roads in the original homologated
(throttled) version. Avoid extended on-road rides at full throttle.
1
DRIVING INSTRUCTIONS »
ENGLISH
18
A
B
Check the following before each start
When you start off, the motorcycle must be in perfect technical condition.
For safety reasons, you should make a habit of performing an overall check
of your motorcycle before each start.
The following checks should be performed:
1 CHECK THE OIL LEVEL
Insufficient oil results in premature wear and consequently to engine
damage.
2 FUEL
Check that there is sufficient fuel in the tank; when closing the filler cap,
check that the tank venting hose is free of kinks.
3 CHAIN
A loose chain can fall from the chain wheels; an extremely worn chain can
tear, and insufficient lubrication can result in unnecessary wear to the chain
and chain wheels. Excessive tensioning of the chain will put additional
load on the components of the secondary drivetrain (chain, bearings of
transmission and rear wheel). Aside from resulting in premature wear, if
worst comes to worst the chain may rupture or the countershaft of the
transmission may break.
4 TIRES
Check for damaged tires. Tires showing cuts or dents must be replaced.
The tread depth must comply with the legal regulations. Also check the
air pressure. Insufficient tread and incorrect air pressure deteriorate the
driving performance.
5 BRAKES
Check correct functioning of the braking system. Check for sufficient
brake fluid in the reservoir. The reservoirs have been designed in such a
way that brake fluid does not need to be refilled even when the brake pads
are worn. If the level of brake fluid falls below the minimum value, this
indicates a leak in the braking system or completely worn out brake pads.
Arrange for the braking system to be checked by a KTM specialist, as com-
plete failure of the braking system can be avoided.
Also check the state of the brake hose and the thickness of the brake
linings.
Check free travel at the hand brake lever and foot brake lever.
6 CABLES
Check correct setting and easy running of all control cables.
7 COOLING FLUID
Check the level of the cooling fluid when the engine is cold.
8 ELECTRICAL SYSTEM
Check correct functioning of headlamps, tail-lights, brake lights, indica-
tors, control lamps and horn while the engine is running.
9 LUGGAGE
If you are taking luggage with you, check that this is securely fastened.
Starting when the engine is cold
1 Open the fuel tap [1].
2 Swing up the side stand or center stand.
3 Put the gear in neutral.
4 Operate the choke [2].
5 Leave throttle closed and kick the kickstarter briskly ALL THE WAY or actu-
ate the E-starter.
If you want to start the engine, make sure that you always put on sturdy
motorcycle boots in order to avoid injuries. You might slip off the kick-
starter, or the engine may kick back and propel your foot upward with great
force.
2
DRIVING INSTRUCTIONS »
ENGLISH
19
Always kick the kickstarter briskly all the way without opening the throt-
tle. If you do not Kick hard enought, with an open throttle grip, the kick-
back hazard will be higher.
Do not start the engine and allow it to idle in a closed area. Exhaust fumes
are poisonous and can cause loss of consciousness and death. Always pro-
vide adequate ventilation while the engine is running.
Always verify that the transmission has been set to idle (neutral) before
actuating the starter button. If you start the motorcycle with a gear engaged,
the motorcycle will move forward.
Maximal period for continuous starting: 5 seconds. Wait at least 5 sec-
onds before trying again.
Don’t ride your motorcycle with full load and don’t rev up the engine when
cold because the piston is warming up faster than the water cooled cylin-
der and can cause engine damage.
NOTE: If you have trouble starting the motorcycle, this could be due to old
fuel in the float chamber. The easily inflammable components of the
new fuels evaporate during longer periods of standstill.When the
motorcycle has been out of operation for more than a week, it is there-
fore recommended to drain the old fuel from the float chamber. The
engine will immediately start off when the float chamber is filled with
new fuel.
Starting when the engine is warm
1 Open the fuel tap [1].
2 Swing up the side stand.
3 Put the gear in neutral.
4 Leave throttle closed and kick the kickstarter briskly ALL THE WAY or
actuate the E-starter.
What to do when the engine is „flooded“
Unscrew the spark plug and dry it.
NOTE:
The carburetor has an accelerator pump. Every time you open the throttle,
fuel will be injected into the intake passage. When starting, be sure that you
open the throttle completely only once.
Starting off
Pull the clutch lever. Put the engine into first gear, slowly release the clutch
lever and open the throttle at the same time.
Before you start off, check that the side stand has been swung up fully. If the
stand drags on the ground, the motorcycle can go out of control.
Shifting/Riding
You are now in first gear, refered to as the drive or uphill gear. Depending on
the conditions (traffic, hill size, etc.), you can shift to a higher gear. Close
throttle, at the same time pull clutch lever in and shift to the next higher gear.
Let clutch lever go again and accelerate. If you turned on the choke, make
sure you turn it off again as soon as engine is warm.
When you reach full speed through opening the throttle all the way, turn throt-
tle back to 3/4; the speed hardly decreases although the engine will use less
gas. Only give as much gas as the engine can handle. Through quick and high
revving of the throttle, the fuel usage increases.
By shifting down, use the brakes if necessary and close the throttle at the
same time. Pull the clutch lever and shift down to the next gear. Let clutch
lever go slowly and open the throttle or shift down again.
DRIVING INSTRUCTIONS »
ENGLISH
20
35 mm
NOTE:
Dedicated to nothing but offroad racing, XC/EXC models make no
compromises in their design. As such, they do not include any radi-
ator fan, and the size of the radiator is dimensioned for optimum
ergonomics.
In normal racing, the cooling system is sufficient.
If you use your motorbike in other conditions, please note that:
the E-starter allows you to start XC/EXC models again at any time.
Therefore, turn off the engine if you intend to run your motorcycle
in idle or at a standstill for longer periods of time (more than 2
minutes).
Avoid letting the clutch slip frequently and for extended periods.
This would cause the engine oil to heat up, thereby heating up the
cooling system. You should drive at low speeds (4-stroke style -
letting the engine pull you) and not at high speeds not by letting
the clutch slip (2-stroke style).
After falling with the motorcycle, check all functions thoroughly
before starting up operations again.
A twisted handlebar must always be replaced. Do not adjust
the handlebar, it will lose stability.
High rpm rates when the engine is cold have an adverse effect
on the life of your engine. We recommend you run the engine
in a moderate rpm range for a few miles giving it a chance to
warm up. After that no further precautions in this respect need
to be taken. The engine has reached its operating temperature
as soon as the radiators become warm.
Never have the throttle wide open when changing down to a
lower gear. The engine will over-rev, damaging the valves. In
addition, the rear wheel locks so that the motorcycle can eas-
ily get out of control.
If any abnormal vibrations occur while driving, check that the
engine fastening bolts are tight.
In the event that, while riding on your motorcycle, you notice
any unusual operation-related noise, stop immediately, turn the
engine off, and contact an authorized KTM dealer.
Braking
Close throttle and apply the hand and foot brakes at the same time.
When driving on sandy, wet or slippery ground use mainly the rear
wheel brake. Always brake with feeling, blocking wheels can cause
you to skid or fall. Always finish braking before you enter a curve.
Also change down to lower gears depending on your speed.
When driving down hill, use the braking effect of the engine.
Change down one or two gears but do not overspeed the engine.
In this way, you will not need to brake so much and the brakes will
not overheat.
In case of rain, after washing the motorcycle, after rides through
water and in case of rides on wet off-road tracks, humid or dirty
brake discs can delay the braking effect. The brakes must be
pulled until they are dry or clean.
Rides on salt-strewed or dirty roads can also delay the braking effect.
The brakes must be pulled until they are clean.
Dirty brake discs cause increased tear of brake pads and brake
discs.
When you brake, the brake discs, brake pads, brake caliper and
brake fluid heat up. The hotter these parts get, the weaker the
breaking effect. In extreme cases, the entire braking system
can fail.
If the resistance in the hand brake lever or foot brake pedal
feels “spongy” (too much play), this is an indication that some-
thing is wrong with the brake system. Don’t ride your motorcy-
cle anymore without first having the brake system looked over
by a KTM dealer.
Stopping and parking
Apply the brakes fully and put the engine into neutral. To turn off
the engine, push the short-circuit button or the emergency-OFF
button with the engine at idling speed until the engine stops. Turn
the fuel tap to the OFF position, park on an area where the ground
is firm, and lock the motorcycle.
Motorcycle engines produce a great amount of heat while running.
The engine, exhaust pipe, muffler, brake rotors, and shock absorbers
can become very hot. Do not touch any of these parts after operating
the motorcycle, and take care to park it where pedestrians are not
likely to touch it and get burned.
Never use the hand decompression lever to turn off the engine.
Use the short-circuit button or the emergency-off button instead.
Close the fuel tap when leaving your vehicle.Otherwise the car-
burettor can flood and fuel will enter the engine.
Never park your motorcycle in places where there are fire haz-
ards due to dry grass or other easily flammable materials.
NOTE REGARDING THE SIDE STAND:
Use your foot to kick side stand forward up to the stop and lean
the motorcycle sideways. Make sure that the ground is solid and
that your motorcycle is standing securely. Just in case, you can
shift into first gear.
The side stand is designed to bear only the load of the motorcycle.
The side stand and/or the frame can be damaged and the motor-
cycle can fall over if you mount the motor-cycle, thus putting an
additional load on the side stand.
Fuel
The engine needs unleaded fuel with at least RON 95 (USA =
Premium PON 91).
Use leaded or unleaded premium grade gasoline (95 octanes). Never
use gasoline having less than 95 octanes because it may damage
the engine.
Gasoline is highly flammable and poisonous. Extreme caution should
be used when handling gasoline. Do not refuel the motorcycle near
open flames or burning cigarettes. Always switch off the engine before
refuelling. Be careful not to spill gasoline on the engine or exhaust
pipe while the engine is hot. Wipe up spills promptly. If gasoline is
swallowed or splashed in the eyes, seek a doctor’s advice immedi-
ately.
Fuel expands when its temperature rises. Therefore do not fill the
tank to the top (see fig.).
Loading...
+ 47 hidden pages