Kodak 5600-J, 4600-KK, 4600, 4400, 4200-KK User Manual

...
0 (0)
Kodak 5600-J, 4600-KK, 4600, 4400, 4200-KK User Manual

Operating Manual

KODAK CAROUSEL® Slide Projector

CONSUMER IMAGING

Important Safety Instructions

When using your projector, always follow basic safety precautions:

1.Read and understand all instructions before using this equipment.

2.Operate this projector with 110to 125-volt 60 Hz current only. Incorrect voltage can cause projector malfunction.

3.Close supervision is necessary when any appliance is used by or near children, or others who may not understand the need for these precautions. Do not leave the projector unattended during use.

4.Be careful not to touch hot parts. For lamp replacement, allow the module to cool before touching the lamp and the surrounding area. Do not place the lamp module on heat-sensitive surfaces.

5.Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged (see “How to Obtain Service” on page 29).

6.Position the cord so that it is not tripped over, pulled, or placed in contact with hot surfaces.

7.If an extension cord is necessary, use a cord with a current rating at least equal to that of the projector. Cords rated for less amperage than the projector may overheat.

8.Always unplug the projector from the electrical outlet before cleaning and servicing and when it is not in use.

9.Allow the projector to cool before storing.

10.Do not immerse this equipment in water or other liquids.

11.Do not disassemble this projector. Use a qualified service technician when service or repair is required. Incorrect reassembly can cause electric shock the next time the projector is used.

12.Use only safety electrical low-voltage (SELV) devices.

13.The use of an accessory attachment not recommended by the manufacturer may increase risk of damage.

14.Keep the air-flow vents unobstructed.

Save These Instructions

Operating Manual

KODAK CAROUSEL Slide Projector

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .Inside Front Cover

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Loading the Slide Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Projecting Your Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Editing Your Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Clearing a Gate Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the Built-In Viewer (Model 5600 Only) . . . . . . . . . . . . . . . . . . 18

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

Changing the Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

Cleaning the Condenser, Heat-Absorbing Glass, and Mirror . . . . . . .

22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Serial Number

The serial number of your projector is printed on the label affixed to the power cord retainer on the base of the projector. Record this number, as well as the model identification, date, and place of purchase, for future reference.

 

KODAK CAROUSEL® Slide Projector

1

 

 

 

Introduction

Congratulations!

You have just purchased a KODAK CAROUSEL Slide Projector which:

triples lamp life

provides brighter and more vivid colors!

Introduction

Take the time to read the instructions in this operating manual to become familiar with your KODAK CAROUSEL® Slide Projector and how to operate it properly.

2

KODAK CAROUSEL® Slide Projector

Overview

FRONT RIGHT

1 – Tray

2 – Lock Ring

3 – Storage Compartment/Remote

4 – Elevating Foot

5 – Elevating Adjustment Wheel

6 – Elevating Foot Release Button

7 – Lens

8 – Viewer (Model 5600)

9 – Focus Knob

10 – Select Bar

11 – Timer (Model 5600)

12 – Reverse

13 – Forward

14 – Power/Fan/Lamp

BACK RIGHT

15 – Tray Release Latch

16 – Lamp Module

17 – Reading Light

18 – Room Light Outlet (Model 5600)

19 – Remote Control Receptacle

BASE

20 – Power Cord

21 – Power Cord Retainer

22 – Leveling Foot

KODAK CAROUSEL® Slide Projector

3

Operation

Operation

Startup

Open the storage compartment and remove the remote control.

Plug the 5-pin cable remote connector into the remote-control receptacle, aligning the raised dot with the metallic rivet head.

Plug the power cord into a grounded outlet with 110to 125-volt 60 Hz current only.

4

KODAK CAROUSEL® Slide Projector

Operation

Loading the Slide Tray

KODAK Slide Trays are available in 80and 140-slide capacities. Use a 140-slide tray if you use thin-mounted slides (1/16 in. / 1.6 mm) and need the larger capacity. Use an 80 cpacity tray if any of your slides have thick mounts (1/8 in. / 2.5 mm).

Note: Do not attempt to project slides mounted with sticky or loose tape.

Place the tray over the center post of the projector. Align the "0" slot with the gate index; the tray will drop into position.

If your 140-slide tray does not drop easily, secure the lock ring, invert the tray, and align the index hole with the index notch. Slide and hold the tray release latch in the direction of the arrow, and turn the bottom plate until the index hole and notch align. Then release the latch. If you use an 80-slide tray, rotate the metal plate on the bottom of the tray until it locks into position.

140-Slide Tray

80-Slide Tray

 

KODAK CAROUSEL® Slide Projector

5

 

 

 

Operation

Adding Your Slides Remove the lock ring by turning it counterclockwise and lifting it off.

Check each slide’s orientation (horizontal or vertical), and arrange them in the order you wish to show them. Then turn the slides upside down.

Number each mount in the upper right-hand corner of the film’s shiny side.

Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray. Insert your second slide in the second slot with the emulsion (dull side) facing your first slide, and so on.

6

KODAK CAROUSEL® Slide Projector

Operation

Replace the lock ring by turning it clockwise until it is secure

Tray

Place the loaded slide tray on the projector. Align the tray index bar with the

 

gate index. The tray will drop into position.

 

KODAK CAROUSEL® Slide Projector

7

 

 

 

Loading...
+ 23 hidden pages