Kodak 7020, 9020, 9010, 7010 User Manual 2

0 (0)

KODAK EKTAPRO 7010/7020/9010/9020 Slide Projector

SUPPLEMENT TO THE MANUAL

©Eastman Kodak Company, 2000

Function Codes

This label is designed to be fixed on the rear of your IR Remote System (transmitter).

Function

Code

 

 

 

Dissolve times

801 - 899

 

(0.1 - 9.9 s)

 

 

CUT

800

 

 

 

 

 

 

 

Random Access

0-160

 

 

 

 

 

 

 

 

Fade:

770

 

 

 

MASTER

 

 

 

SLAVE

707

 

 

 

 

 

 

 

 

Alternate

777

 

 

 

 

 

 

 

 

Freeze

789

 

 

 

 

Independent

980

 

Projector Control

 

 

Mode

 

 

 

 

 

 

 

• Parallel

970

 

 

projection

666*

 

 

Focus Slave*

 

Reactivating

990

 

dissolve mode

 

 

 

 

Remote Security

989

 

Mode

 

 

 

 

 

 

 

 

Reset

999

 

 

 

 

 

 

Autotimer

601 - 660

 

 

(1-60 s)

 

 

 

----- off

600

 

 

 

 

 

*Function is inactivated for models 7010 and 9010!

5

Kodak 7020, 9020, 9010, 7010 User Manual 2

Presentations with KODAK EKTAPRO 7010, 7020, 9010 and 9020 Slide Projectors

One of the important new features of the KODAK EKTAPRO 7010, 7020, 9010 and 9020 Slide Projectors is the integrated dissolver for a 2-projector dissolve.

You just have to link two projectors using the KODAK Dissolve Cable (accessory) and you can immediately run more interesting and lively live presentations using the infrared remote control. It is also possible to play automatic slide shows with a fixed dissolve time. However, it is not possible to record the IR-commands.

Projection with a single projector (Soft Slide Change)

If you are just presenting with a single EKTAPRO 7010, 7020, 9010 or 9020, you can fade your slides out and back in again (e.g. by setting a dissolve time to smoothly change the slides). This means the hard light change is avoided during slide transport.

The commands and notes which relate to the control of an individual projector are marked with an *.

Projection with two projectors

Choosing projectors (MASTER/SLAVE)

All commands for dissolving etc. are only transmitted to one projector. This projector is called the MASTER. It passes the commands on to the second projector which is known as the SLAVE.

You can use either the KODAK EKTAPRO 7010, 7020, 9010 or 9020 projector as a MASTER

However, you can use all EKTAPRO models with a

P-Bus-in interface as a SLAVE!

Note: The use of all functions is only possible via EKTAPRO IR-Remote Control! With the KODAK EKTAPRO Cable Remote only dissolves in the default setting (0.5 sec) can be carried out.

Setting up

Putting your 2 projector dissolve system together is fast and easy. Connect the two projectors via the P-bus-in interface to the KODAK Dissolve Cable (accessory) as shown in the illustration! Connect your remote control to the MASTER projector! Switch the projectors on. Your 2 projector dissolve system is now ready to use.

Comments

Even when the two projectors are linked with the dissolve cable, they behave like individual projectors and can also be operated individually as usual via the keypad.

If your SLAVE projector has a built-in timer, it must be switched off!

If you want to use only one projector in single mode, simply switch off the SLAVE and use the MASTER!

Aligning the projectors

It is important to align the two slide projectors before beginning a presentation such that both projected images cover the same area. This is easiest using so-called aligning slides which your AV dealer will certainly carry in stock (it is useful to load the aligning slide in the tray

compartment 80):

Place the slide trays onto the projectors.

Press the slide reverse transport button on both projectors.

Focus both slides using the focus buttons on your projectors.

Now align the projectors to project both slides on the same area.

Now return both slide trays to their initial position (zero position).

You can now begin your presentation using the remote control.

Comment (EKTAPRO 7010, 7020, 9010 or 9020)

If it is necessary to carry out any additional adjustment during the presentation push both transport buttons on the “dark” projector for longer than one second. The “dark” projector is now faded in too. Switch-off the lamp again by pressing standby.

Sorting slides into the slide trays

Once you have decided on the order of your slides, number them through. Then sort all the slides with uneven numbers in sequence into the slide tray for the MASTER projector.

The slides with even numbers are sorted in order into the slide tray for the SLAVE projector (see the table page 34).

6

Loading...
+ 4 hidden pages