Kicker QS65.2, QS60.2 User Manual

QS

QSCOMPONENTSYSTEM

QS65.2

QS60.2

English Version

Versión Español

Sistema de altavoces componentes QS

Manual del Propietario

Deutsche Version

QS-Komponentensystem

Benutzerhandbuch

Version Française

Système à composants QS

Manuel d’utilisation

	2009 QS Multilingual h01.indd 1			11/21/2008 10:54:11 AM

QSCOMPONENTSYSTEMOwner’sManual

MODEL:

QS65.2 / QS60.2

Authorized KICKER Dealer:

Purchase Date:

Speaker Model Number:

QS COMPONENTS

The KICKER QS-series component systems offer unmatched audio fi delity for vehicle applications. Whether you’re confi guring the ultimate multi-speaker and subwoofer surround system or simply upgrading from dull, lifeless factory speakers, the QS component systems deliver the most pleasing fullrange sound on the market today!

PERFORMANCE
Model:	QS60.2	QS65.2
Woofer Size	6” (160mm)	6.5” (165mm)
Tweeter Size	1-3/16” (30mm)	1-3/16” (30mm)
Dome Material	Tetoron®	Tetoron®
Impedance, (DC Resistance)	4Ω, (3.5Ω)	4Ω, (3.5Ω)
Power Handling Peak, (RMS)	180W, (90W)	200W, (100W)
Sensitivity @ 1W, 1m	86dB	87dB
Effective Frequency Range	50Hz–22kHz	40Hz–22kHz
Woofer Mounting Hole Diameter	5-1/16” (129mm)	5-7/16” (138mm)
Woofer Mounting Depth	≤ 2.5” (63.5mm)	≤ 2.5” (63.5mm)
Tweeter Hole Diameter	1-13/16” (46mm)	1-13/16” (46mm)
Flush-mount Tweeter Depth	1-1/8” (29mm)	1-1/8” (29mm)
Crossover High Pass Filter	24dB/octave @ 2.8kHz	24dB/octave @ 2.8kHz
Crossover Low Pass Filter	12dB/octave @ 2.8kHz	12dB/octave @ 2.8kHz
High Frequency Output Level	0dB, +3dB, +6dB	0dB, +3dB, +6dB

Pro Tip: Looking for the next step in audio performance from your QS components? Upgrade to a KICKER IX or ZX 4-channel amplifi er for each QS component system you have installed to take full advantage of the QS’s bi-amping capabilities. With a dedicated amplifi er channel for each tweeter and each midrange driver, you’ll have a more effi cient system that will deliver a clearer soundstage and

an increasingly dramatic dynamic response. In other words, your music will be more expansive and captivating.

2	QSCOMPONENTSYSTEM
2009 QS Multilingual h01.indd 2				11/21/2008 10:54:27 AM

CONFIGURATION

Before mounting and wiring the QS component system, determine which confi guration you will use for the speakers and crossover.

	QS Speaker	ADVANTAGES	CONSIDERATIONS
	Configurations
	Coaxial	great for space-limited applications	high frequencies may not be as
		or when separate tweeter mounting	prominent | tweeter output may
		is not possible	need to be increased at crossover
	Separates	optimal sound quality and improved	trickier install | vehicle must have a
		sonic imaging (with proper tweeter	good tweeter mounting location
		mounting)
	QS Crossover	ADVANTAGES	CONSIDERATIONS
	Configurations
	Conventional 2-way	easy install | ideal when available	audio fi delity not quite as high as
		amplifi er channels are limited	bi-amplifi ed confi guration
	Bi-amplifi ed	optimal sound quality; more effi cient	requires at least 4 amplifi er
		usage of amplifer power	channels | slightly trickier install

tweeter

tweeter

phase plug

Coaxial Configuration

Separates Configuration

SPEAKER CONFIGURATION

The QS component system comes packaged in a separates confi guration.

To use a coaxial confi guration, see Fig. 1 and follow these steps:

1.Unscrew and remove the aluminum phase plug from the center of the woofer.

2.Screw the coaxial mounting adapter into the woofer in place of the phase plug.

3.Screw the tweeter into the tweeter post.

4.Thread the tweeter’s lead wires through the center of the woofer.

5.Snap the tweeter post onto the coaxial mounting adapter.

6.Rotate the tweeter clockwise for the most appealing position.

7.Secure the tweeter’s lead wires using the clip on the underside of the woofer.

3

2009 QS Multilingual h01.indd 3			11/21/2008 10:54:27 AM

Step 1

Fig. 1

Configuring the QS for

Coaxial Operation

	coaxial mounting adapter
Steps 2–6	tweeter post	Step 7

tweeter

tweeter lead wires

Fig. 2

QS crossover

INPUT jumper.

Install only for 2-way confi gurations; do not install if bi-amping.

tweeter output-level jumpers.

One of these jumpers MUST be installed. Higher numbers mean more volume from the tweeter.

+3 dB

0 dB

CROSSOVER CONFIGURATION

The KICKER QS crossover can be confi gured as a conventional 2-way crossover by installing the included INPUT jumper into the - MID + -TW + input terminals as shown in Fig. 2. In this confi guration, the amplifi ed signal from your source unit or amplifi er should be wired to the + and - terminals indicated on the INPUT jumper.

The QS crossover can also be confi gured for bi-amp wiring by removing (or simply not installing) the INPUT jumper. To use the bi-amp confi guration, you must connect two amplifi ed signals to each crossover (you will need at least four amplifi er channels). Install one of the included tweeter outputlevel jumpers (0 dB, +3 dB, or +6 dB) to adjust the tweeter output level. Installing jumpers with higher numbers will result in more volume from the tweeter.

4	QSCOMPONENTSYSTEM
2009 QS Multilingual h01.indd 4				11/21/2008 10:54:27 AM

WIRING

We recommend using 16 gauge (or larger) wire. The QS components are rated at 4 ohms and work with any source unit or amplifi er designed to operate at a 4 ohm load. Make sure your source unit or amplifier is rated for 4 ohm operation.

Crossover in 2-way configuration | One component set per channel

• At least two amplifi er channels are needed for stereo operation (only one channel is shown)

crossover

woofer

+ - tweeter

+-

OUT	OUT
-MID+ - IN +	-TW+

source unit / amplifi er		-OUT+

Crossover in 2-way configuration | Two component sets per channel

•Requires two complete QS systems (four woofers, four tweeters, four crossovers)

•At least two amplifi er channels are needed for stereo operation (only one channel is shown)

•Crossovers wired in series

+

-

+

+

-

-

+

-

OUT	OUT	OUT	OUT
-MID+ - IN +	-TW+	-MID+ - IN +	-TW+

- OUT +

source unit / amplifi er

5

2009 QS Multilingual h01.indd 5			11/21/2008 10:54:28 AM

Crossover in bi-amp configuration Two channels per component set

•At least four amplifi er channels are needed for stereo operation (only two channels are shown)

amplifi er / source unit

(must have at least four channels)

+

-

+

- OUT				OUT +
+ MID				TW -
	IN			IN
-MID+			-TW+
-MID+ -TW+
	CH2			CH1

LEFT OUTPUT

-

Crossover in bi-amp configuration | One channel per component set

•	Requires two complete QS systems (four woofers, four tweeters, four crossovers)
•	At least four amplifi er channels are needed for stereo operation (only two channels are shown)
•	Crossovers wired in series

+

-

+

- OUT	OUT +
+ MID	TW -
IN	IN
-MID+	-TW+

-

+

-

+

- OUT	OUT +
+ MID	TW -
IN	IN
-MID+	-TW+

-

-MID+ -TW+ CH2 CH1

LEFT OUTPUT

amplifi er / source unit

(must have at least four channels)

6	QSCOMPONENTSYSTEM

2009 QS Multilingual h01.indd 6			11/21/2008 10:54:29 AM

WOOFER MOUNTING

The KICKER QS components are designed for free-air applications and do not require a sealed enclosure for optimum performance. It is important to isolate the sound coming from the front of the speaker from the sound radiating from the back of the speaker. This is most easily accomplished by mounting the speakers in a vehicle’s factory locations or in a location with a semi-isolated rear chamber (like the rear deck of a car behind the rear seats).

If you are replacing factory speakers in their original locations, you may have to enlarge the speaker cut-outs and pre-drill new screw holes using a 7/64” (2.5mm) bit. Custom mounting locations will require more preparation and work. Make sure that the speaker will not interfere with trunk and door opening and closing mechanisms and that the enclosed screws will not puncture the fuel tank, puncture wiring, or interfere with any other mechanical parts on the underside of the mounting surface. Cycle the windows all the way down and up.

If the speaker cut-out locations require you to cut metal, avoid structural metal and braces. If the door body and panel cannot support the weight of the speaker, an optional reinforcing ring (thin piece of wood or Medium Density Fiberboard) may be fastened or adhered to the door body. Mount the speaker to the vehicle as outlined in Fig. 3.

door body

Fig. 3

reinforcing ring (optional)

door panel

speaker cut-out

QS woofer

screws

speaker grille

7

2009 QS Multilingual h01.indd 7			11/21/2008 10:54:30 AM

panel

mounting nut

Trim the mounting nut legs at the score lines to accommodate thicker panels.

tweeter

fl ush ring

Fig. 4

Flush Mounting the Tweeter

tweeter

front angle ring

panel	back angle ring
	mounting nut

rounded surface

inset surface

Fig. 5

Angle Mounting the Tweeter

TWEETER MOUNTING

The tweeter can be mounted one of three ways: fl ush, angled, and coaxial mounting. For fl ush mounting applications, see Fig. 4. Choose a fl at location on the panel with space behind the panel to allow room for the mounting nut, motor structure, and tweeter post. After checking the clearances, cut a 1-13/16” (46mm) diameter mounting hole in the panel. Position the mounting nut behind the panel. Feed the

wire through the optional fl ush ring, the hole in the panel, and the mounting nut. Mount the tweeter by screwing the mounting nut onto the tweeter.

For angled mounting applications choose a fl at location on the panel with space behind the panel to allow room for the mounting nut, motor structure, tweeter post, and back angle ring. After checking the clearances, cut a 1-13/16” (46mm) diameter mounting hole in the panel. Place the front angle ring in front of the panel. Then place the wire and tweeter through the front angle ring and into the panel. Next, place the wire through the back angle ring, place the back angle ring over the rear of the tweeter, and line-up the narrow part of the front angle ring for the preferred angle of operation. Place the wire through the mounting nut and loosely tighten the mounting nut around the tweeter. Rotate all the parts in unison until the tweeter is angled in the desired direction. Secure the assembly by tightening the mounting nut. See

Fig. 5.

8	QSCOMPONENTSYSTEM
2009 QS Multilingual h01.indd 8				11/21/2008 10:54:30 AM

CROSSOVER MOUNTING

Mount the crossover in a location that is easy to access for wiring and tweeter output level adjustment. Make sure that the crossover will not be exposed to water. The bottom of the car door is not a good location. If you must mount the crossover in the car door, exercise caution as water can accumulate in the bottom of the door. Keep the crossover high in the door and shielded from water.

QS crossover. (mounted inside

door panel)

door jamb

tweeter mounting hole

to tweeter lead wires

woofer mounting hole	to woofer
	terminals

rubber	from amplifi er or
grommets	source unit

If factory speaker wiring is not available in your desired location, it may be necessary to run speaker wire through the door jamb. The speaker wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. An existing grommet in the door jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole to run the speaker wire through the door jamb. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage.

9

2009 QS Multilingual h01.indd 9			11/21/2008 10:54:30 AM

GRILLE MOUNTING

10	QSCOMPONENTSYSTEM
2009 QS Multilingual h01.indd 10				11/21/2008 10:54:31 AM

stillwaterdesigns

ACOUSTICS LIMITED WARRANTY

KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases you must have the original receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or

malfunction during the warranty period, KICKER will repair or replace (at its discretion) the defective merchandise with equivalent merchandise at no charge. Warranty replacements may have cosmetic scratches and blemishes.

Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty gives you specifi c legal rights; however you may have other rights that vary from state to state.

WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:

Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs directly. You can confi rm that a dealer is authorized by asking to see a current authorized dealer window decal.

If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER Customer Service Department at [phone] for a Return Merchandise Authorization (RMA) number. Package only the defective items in a package that will prevent shipping damage, and return to:

Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075

The RMA number must be clearly marked on the outside of the package. Please return only defective components. The return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you. For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy

of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing the Customer’s name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof-of- purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent freight-collect, or COD, will be refused.

WHAT IS NOT COVERED?

This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover: o Damage due to improper installation

o Subsequent damage to other components

o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation

o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered abuse

o Any cost or expense related to the removal or reinstallation of product o Speakers damaged due to amplifi er clipping or distortion

o Items previously repaired or modifi ed by any unauthorized repair facility o Return shipping on non-defective items

o Products with tampered or missing barcode labels

o Products returned without a Return Merchandise Authorization (RMA) number o Freight Damage

o The cost of shipping product to KICKER

o Service performed by anyone other than KICKER

HOW LONG WILL IT TAKE?

KICKER strives to maintain a goal of 48-hour service for all acoustics (subwoofers, midrange drivers, tweeters, crossovers, etc) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department at [phone]. Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’s warranty policies.

Note: All specifi cations and performance fi gures are subject to change. Please visit www.kicker.com for the most current information. To get the best performance from your new KICKER speakers, we recommend using genuine KICKER accessories and wiring. Please allow two weeks of break-in time for the speakers to reach optimum performance.

P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510				20081107+G-09QS 11
2009 QS Multilingual h01.indd 11				11/21/2008 10:54:31 AM

Manual del propietario del SISTEMA DE

COMPONENTES QS

MODELO:

QS65.2 / QS60.2

Distribuidor autorizado de KICKER:

Fecha de compra

Número de modelo del altavoz:

COMPONENTES QS

Los sistemas de componentes de la serie QS de KICKER ofrecen una fi delidad de audio inigualable para aplicaciones para vehículos. Ya sea para confi gurar el último sistema de sonido envolvente con altavoces múltiples y subwoofer o simplemente para mejorar la versión de parlantes aburridos y sin vida de fábrica, los sistemas de componentes QS brindan el sonido de gama completa más placentero del mercado en la actualidad!

RENDIMIENTO
Modelo:	QS60.2	QS65.2
Tamaño del woofer	6” (160 mm)	6,5” (165 mm)
Tamaño del tweeter	1-3/16” (30 mm)	1-3/16” (30 mm)
Material del domo	Tetoron®	Tetoron®
Impedancia, (Resistencia CC)	4Ω, (3.5Ω)	4Ω, (3.5Ω)
Procesamiento de potencia máxima,	180 W, (90 W)	200 W, (100 W)
(valor efi caz, root mean square, RMS)
Sensibilidad a 1 W/1 m	86 dB	87 dB
Gama efi caz de frecuencias	50 Hz–22 kHz	40 Hz–22 kHz
Diámetro del orifi cio de montaje del woofer	5-1/16” (129 mm)	5-7/16” (138 mm)
Profundidad de montaje del woofer	≤ 2,5” (63,5 mm)	≤ 2,5” (63,5 mm)
Diámetro del orifi cio del tweeter	1-13/16” (46 mm)	1-13/16” (46 mm)
Profundidad de montaje al ras del tweeter	1-1/8” (29 mm)	1-1/8” (29 mm)
Filtro de paso alto crossover	24 dB/octava a 2,8 kHz	24 dB/octava a 2,8 kHz
Filtro de paso bajo crossover	12 dB/octava a 2,8 kHz	12 dB/octava a 2,8 kHz
Nivel de salida de alta frecuencia	0 dB, +3 dB, + 6 dB	0 dB, +3 dB, + 6 dB

Consejo profesional: ¿Busca mejorar el rendimiento de audio de sus componentes QS? Actualice cada sistema de componentes QS que tenga instalado en un amplifi cador de 4 canales KICKER IX o ZX para aprovechar al máximo la capacidad de biamplifi cación de QS. Con un canal amplifi cador dedicado para cada tweeter y cada excitador de alcance medio, tendrá un sistema más efi caz que producirá un campo acústico más claro y una respuesta dinámica cada vez más espectacular. En otras palabras, su música será más expansiva y cautivadora.

12	SISTEMADE COMPONENTESQS
2009 QS Multilingual h01.indd 12				11/21/2008 10:54:32 AM