KEYENCE CV-X200 User Manual

0 (0)

96M13189

High-speed, High-capacity

Machine Vision System

CV-X200Series

Controller Instruction Manual

Read this manual thoroughly before using the CV-X200 Series. Always keep this manual in a safe place for future reference.

Introduction

This manual describes the hardware information. Read this manual thoroughly to understand how the CV-X200 Series works in order to maximize the performance of the system.

This manual is for the CV-X200 Series. All references however, unless otherwise noted, pertain to the CV-X270F. For more details about the differences between the models, see "Main Specifications" (page 7) and the "CV-X Series User's Manual".

Always keep this manual in a safe location for future reference.

Please ensure that the manual is passed to the end user of the controller.

Symbols

The following symbols alert you to important messages. Be sure to read these messages carefully.

DANGER

It indicates a hazardous situation which, if not avoided, will result in death or serious injury.

 

 

 

It indicates a hazardous situation which, if not avoided, could

 

WARNING

 

 

 

result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

It indicates a hazardous situation which, if not avoided, could

 

CAUTION

 

 

 

result in minor or moderate injury.

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE

It indicates a situation which, if not avoided, could result in

 

product damage as well as property damage.

 

 

 

 

 

 

 

 

 

 

 

Important

It indicates cautions and limitations that must be followed during operation.

Point It indicates additional information on proper operation.

It indicates tips for better understanding or useful information.

Reference

Trademarks

"SD Memory Card" is a registered trademark of the SD Association.

Other company names and product names noted in this document are registered trademarks or trademarks of their respective companies. The TM mark and ® mark are omitted in this manual.

Libraries and programs

libjpeg

Copyright ©1991-2012, Thomas G. Lane.

This software is based in part on the work of the Independent JPEG Group.

1

Package Contents

The equipment and accessories listed below are included in the package when shipped. After opening the carton, check that you have received all of the equipment and accessories listed below.

Standard Package

• Controller Unit × 1 (CV-X200/X250/X270)

• SD Card

(OP-87133 (512MB): CV-X200/X250, CA-SD1G (1GB): CV-X270) × 1 (pre-installed in SD1 slot)

• Dedicated mouse (OP-87506) × 1

• Software DVD-ROM for PC × 1

• Controller instruction manual × 1

Safety Precautions

General Cautions

Do not use this product for the purpose of protecting the human body or any part thereof.

 

WARNING

 

• Because this product was not designed for use in an

 

 

 

explosion-proof area, it must never be used in an explosion-

 

 

 

proof area.

 

 

 

 

 

 

 

 

 

 

 

• Before starting or operating the system, check to make sure

 

 

 

all system functions are working properly.

 

CAUTION

 

 

 

• If any Keyence product fails, take all safety precautions to

 

 

 

 

 

 

prevent damage before using the system again.

 

 

 

 

 

 

 

 

 

 

 

• If the system is operated beyond its published specifications

 

 

 

or if the system is modified, its functions and performance

 

 

 

cannot be guaranteed.

 

 

 

• Please note that when the system is used in combination

 

NOTICE

with other instruments, its functions and performance may

 

 

 

be degraded.

Do not subject the controller or connected devices to a sudden change in temperature.

There is the risk of condensation occurring.

General cautions for the controller

 

 

 

• Do not use with any power voltage other than 24 VDC. Doing

 

 

 

so may cause fire, electric shock, or product malfunction.

 

CAUTION

 

 

 

• Do not disassemble or modify the unit. Doing so may cause

 

 

 

 

 

 

fire or electric shock.

 

 

 

 

Operating environment and conditions

To use the system properly and safely, avoid installing this unit in the following locations. Doing so may cause fire, electric shock, or product malfunction.

Locations that contain moisture or dust, or that are poorly ventilated.

Locations where the system is exposed to direct sunlight or temperature increases.

CAUTION – Locations where there are flammable or corrosive gases.

Locations where the unit may be directly subjected to vibration or impact.

Locations where water, oil or chemicals may splash onto the unit.

Locations where static electricity is present or electric discharge may occur.

 

• Keep this unit and cables away from high-tension cables and

 

power lines.

 

Otherwise, noise may cause malfunction or accidents.

 

• Bundle cables with spiral tubing material. Direct bundling will

NOTICE

concentrate the cable load on the bindings, which can result

 

in cable damage or short circuit.

 

• The controller and optional devices are precision

 

components. To maintain performance do not subject them

 

to vibration or shock.

 

 

Measures to be taken when an abnormality occurs

 

 

 

In the following cases, turn the power OFF immediately. Using

 

 

 

the unit in an abnormal condition may cause fire, electric shock,

 

 

 

or product malfunction. Contact your local Keyence office for

 

CAUTION

 

repair.

 

 

 

• If water or debris enters the system

 

 

 

• If the system is dropped or the case is damaged

 

 

 

• If smoke or a burning smell emits from the controller

 

 

 

 

Usage

 

• Before making any connections/disconnections, be sure to

 

turn off the power of this unit and connected devices. Failure

 

to do so may result in a malfunction of the controller or

 

connected devices.

 

• Do not turn the power off while you are programming.

NOTICE

Otherwise, all or part of the program settings may be lost.

• Do not block the ventilation holes. Otherwise, the inside

 

 

temperature may rise and a malfunction may occur.

 

• Do not allow an excessive amount of sunlight or bright indoor

 

light to enter the camera for a long period of time. Doing so

 

may cause damage to the image capture surface inside the

 

camera.

 

 

Maintenance

 

• Do not clean with benzene, thinner, or alcohol. Doing so may

NOTICE

cause discoloration or deformation of the unit.

• If the unit has any dirt on it, wipe it off with a cloth moistened

 

 

with a mild detergent, then wipe with a dry cloth.

 

 

Precautions on Regulations and Standards

CE Marking

KEYENCE evaluates compliance with the requirements of the EC directive according to how products fulfill the below conditions. KEYENCE has confirmed that this product meets these requirements. When this product is used in EU nations, take note of the following precautions.

EMC Directive (2004/108/EC)

• Applicable standard EMI: EN61326-1, Class A EMS: EN61326-1

Use cables shorter than 30 m to connect the controller and its external devices.

However, these precautions do not guarantee that the customer’s entire machinery installation is compliant with the EMC Directive. The customer is responsible for determining the compliance of the overall machinery installation.

2

KEYENCE CV-X200 User Manual

Identifying Controls and Connectors

Parallel I/O connector

Use to connect the parallel input/output signals.

SD2 slot (upper), SD1 slot (lower)

Insert an SD card.

The lower slot (SD1) holds the included SD card (512 MB or 1 GB) by factory default.

Important SD Card 1 must be inserted while the device is operating.

Camera slot

Use to connect the camera input unit.

At the time of shipping, the area camera input unit (CA-EC80) is connected to this slot.

USB connector for the dedicated mouse

Use to connect the included dedicated mouse.

The USB port is used exclusively for the dedicated mouse (OP87506).

NOTICE Connecting other equipment including a commercial USB mouse can cause a malfunction or damage to the controller or connected devices.

RGB output terminal

Use to connect to an external monitor.

Camera 2 connector

Use to connect camera 2.

USB connector

Use to connect a USB cable.

Expansion unit connector 1

(right side, only for CV-X250/X270)

Use to connect the camera expansion unit (CA-E800).

Camera 1 connector

Use to connect camera 1.

TOUCH PANEL port

Use to connect an optional RS-232C cable for the touch panel (OP87258: 3 m/OP-87259: 10 m).

RS-232C port

Use to connect an optional RS-232C communication cable (OP-26487: 2.5 m) or an optional RS-232C modular cable for touch panels (OP-87264: 3 m/OP-87265: 10 m).

ETHERNET connector

Use to connect an Ethernet cable.

Terminal block

Use for signal input and output.

Power and ground terminals

Use to connect power (24 V DC) and the ground wire.

Expansion unit connector 2 (left side)

Use to connect the illumination expansion unit CA-DC10E, CA-DC21E, or CA-DC30E.

Installing the Controller Unit

Install the controller unit to DIN rail, or use the holes on the bottom of the controller to secure it with screws.

Do not install the controller in a location with lots of dust or water vapor.

The controller does not have a mechanism to protect it from dust or water. Dust or water entering the controller can cause damage to the controller.

Turn off the power to the controller when connecting or removing an expansion unit, a cable, or a terminal block.

NOTICE

Connecting or removing the camera expansion unit, the

 

 

cable, or the terminal block while the power is being supplied

 

may damage the controller or peripheral devices.

When an expansion unit is not connected, place the connector protection cover back on the controller. Using the controller with the connector exposed may cause damage to the controller.

Caution on Direction of Controller Mounting

Install the controller in the direction indicated by the circle shown below. Do not install the controller in any other direction.

For ventilation, keep the space free of objects for 50 mm or more above the controller and 50 mm or more for both sides. Keep the space free of objects for 90 mm or more in the front of the connector panel in order to connect the cables safely.

When two or more controllers are installed side by side, maintain 50 mm or more of space between the controllers, and 50 mm or more above both controllers.

 

50 mm

50 mm

50 mm

50 mm

50 mm

Do not block the ventilation openings on the top and bottom of the controller. If the vents are blocked, heat will accumulate inside the controller and can cause a system failure.

When installing the controller on a surface, pierce holes in

the surface at the positions of the ventilation openings on the

bottom of the controller or perform similar operations to NOTICE ensure that there is ventilation from the bottom of the

controller to the top.

If the temperature inside the control panel (temperature at the bottom of the controller) exceeds the rating, use forced air-cooling or increase the free space around the system to improve ventilation until the operating ambient temperature decreases below the rating.

3

Loading...
+ 5 hidden pages