USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new Special Edition B60 Keurig® Brewer
COMMENT UTILISER VOTRE CAFETIÈRE
MANUEL D’UTILISATION : Tirez le meilleur de votre nouvelle cafetière Édition spéciale B60 de Keurig®
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic safety precautions should be followed, including the following:
1.Read all instructions before using.
2.Do not touch hot surfaces. Use handle and knobs when available.
3.This appliance must be properly installed and located in accordance with these instructions before it is used.
4.The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock or injury to persons.
5.Do not place on or near a hot gas or electric burner, or in a heated oven.
6.Do not use outdoors.
7.To protect against fire, electric shock and injury, do not immerse cords, plugs or the appliance in water or any other liquid.
8.Do not overfill the Water Reservoir with water.
9.Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir, except as instructed in the Cleaning Instructions in this guide.
10.Turn off and unplug the Brewer before cleaning or maintenance. Allow to cool
before putting on or taking off parts and before cleaning the appliance.
11.For best operation, plug the appliance into its own electrical outlet on a dedicated circuit
to prevent flickering of lights, blowing of fuses or tripping a circuit breaker.
12.Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is damaged in any manner. Contact Keurig Customer Service to report any malfunction of or damage to the Brewer.
13.Do not let the cord hang over the edge
of the table or counter, or touch hot surfaces.
14.To disconnect, press the Power Button on the back of the Brewer to “OFF” status, and then remove the plug from the wall outlet.
15.Close supervision is necessary when any appliance is used by or near children.
16.Do not lift the Brewer Handle while brewing is in progress.
17.Always keep the Water Reservoir Lid on the Water Reservoir unless you are refilling it.
18.This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be
grounded using a 3-hole, properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
19.If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
21.Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded.
22.Do not use the appliance for any reason other than its intended use.
Save These Instructions.
WARNING TO USERS AND PARENTS
1.DO NOT permit children to use brewer unless there is adult supervision. Brewer dispenses very hot water.
2.SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER USING A HOT COCOA K-CUP, RUN a Hot Water Brew Cycle without a K-Cup to avoid the possibility of clogging the exit needle. DO NOT assume the next user will do this.
2
CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Assembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over un-
intentionally; and (3) the extension cord must include a 3-prong grounding plug. THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
WARNINGTHIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR !
ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
Special Edition — Model B60
Using Your Brewer
SET-UP |
|
Helpful Hints......................................................................................... |
4 |
Unpacking............................................................................................. |
4 |
Features................................................................................................ |
5 |
SECTION 1 — SET-UP & FIRST BREW |
|
Set-Up & First Brew............................................................................ |
6 |
SECTION 2 — CONTROLS & INDICATORS |
|
Setting the Clock................................................................................ |
10 |
Programming On/Off Features....................................................... |
10 |
Programming Brew Temperature.................................................. |
12 |
SECTION 3 — CLEANING & MAINTENANCE |
|
Cleaning.............................................................................................. |
12 |
De-Scaling.......................................................................................... |
13 |
Storage................................................................................................ |
14 |
SECTION 4 — TROUBLESHOOTING.................................................. |
15 |
SECTION 5 — WARRANTY................................................................. |
16 |
Pour des directives en français, veuillez vous reporter à la page 17.
Record your Brewer Serial Number here.
Removing the serial number label from the brewer will void warranty.
3
Set-Up
Helpful Hints
1. Keep your Brewer turned “ON” at all times.
To brew a fresh cup of coffee, tea or hot cocoa anytime you want, we suggest you keep your Brewer turned “ON” all the time. However, the Brewer is fully programmable so you can set it to turn on and off automatically to match your schedule. Or, if you prefer, set the Brewer to automatically turn off after a period of time. Follow the simple instructions on pages 10–12 to make using the Brewer convenient for you.
2.For the best tasting gourmet coffee, tea or hot cocoa, Keurig recommends using bottled or filtered water.
Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee, such as chlorine or other mineral tastes, we recommend you consider using bottled water or water from a filtration system.
3.Customize the Size, Flavor & Brew That’s Perfect for You.
With the choice of over 200 varieties of K-Cups and 3 brew sizes (Small Cup-5.25 oz., Small Mug-7.25 oz. and Large Mug-9.25 oz.) your Keurig Brewer gives you endless options to customize the size, flavor and brew that’s
perfect for you. For a strong, intense cup, select an Extra Bold K-Cup (with up to 30% more ground coffee than regular varieties) and brew size that’s right for you. The smaller the brew size, the more intense flavor in your cup. The larger the brew size, the less intense flavor in your cup.
4.Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other appliances, your Brewer may not function properly. The Brewer should be operated on its own circuit, separate from other appliances.
5.Brewing into a travel mug.
To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base.
6.De-Scale Brewer regularly.
Please see page 13 for instructions.
Unpacking Instructions
1.Place Brewer box on a large steady surface (such as a table or countertop) or on the floor. Open the box.
2.Remove enclosed literature.
3.Turn the box on its side with front of box face down.
4.Reach into the box and grasp the plastic bag that contains the Brewer.
5.Carefully pull the plastic bag (and packaging materials) toward you and out of the box. The Brewer will still be encased in the polyfoam and be on its side.
6.Remove the top polyfoam packaging material.
7.Carefully lift Brewer off of the bottom polyfoam and place it upright on a flat, steady surface.
8.Lift plastic bag off of Brewer.
9.Record the serial number for this Brewer on page 3 of this guide. The serial number can be found on the bottom of the Brewer box or on the Brewer behind the Drip Tray (when removed).
10.Place the Brewer upright on a flat, steady surface. Remove tape holding Water Reservoir in place.
We recommend you save all packing materials in case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away from children.
4
Features Special Edition — Model B60 Brewer
|
D |
G |
|
T |
|
|
|
|
|
A |
|
|
|
|
|
M |
|
|
READY |
|
|
S |
TO BREW |
|
|
|
|
|
|
|
H |
|
F |
11:56 AM |
|
|
MENU |
||
B |
C |
E |
|
R |
|
|
|
|
|
|
N |
|
|
|
|
I |
|
J |
|
|
|
|
|
|
|
|
K |
0 |
P Q |
|
L |
|
|
|
|
|
|
|
|
Special Edition B60 Brewer |
|
Controls and Indicators |
|
|
A.Water Reservoir Lid
B.Water Reservoir
C.Water Reservoir Lock Tab Slots
D.Handle
E.Funnel
F.K-Cup® Portion Pack Holder (E and F are the K-Cup Holder Assembly)
G.Lid
H.K-Cup Portion Pack Assembly Housing
I. Housing |
O. Small Cup Button 5.25 oz. |
R. Menu Button |
J. Drip Tray Plate |
P. Small Mug Button 7.25 oz. |
S. LCD Control Center |
K. Drip Tray |
Q. Large Mug Button 9.25 oz. |
T. Power Button |
L.Drip Tray Base
M.Vent
N.Power Cord
5
SECTION 1 Set-Up & First Brew
IMPORTANT: You cannot use your Keurig Brewer until it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures below freezing, allow Brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold brewer will not operate.
fig. 1 Setting Up Your Brewer
1. Unwrap cord and plug the Brewer into a grounded outlet. Remove all pieces of packing tape and clear plastic sticker from LCD display.
2. Place a large mug (10 oz. min) on the Drip Tray Plate.
3. Remove the Water Reservoir from Brewer by first removing Lid from Reservoir (fig. 1), then lifting Reservoir straight up and away from Brewer (may be tight), (fig. 2). Rinse with fresh water.
6
Lock Tabs fig. 2
fig. 3
Power
NOT READY
ADD
WATER
Small
Mug
4.Fill Water Reservoir with bottled or filtered water so that the water level is just below the top edge of the Water Reservoir.
5.Place Water Reservoir base into the left side of the Brewer and be sure the Water Reservoir Lock Tabs engage with the Brewer. Replace Lid on Water Reservoir.
6.Press the Power Button found directly above the LCD Control Center (fig. 3).
7.The LCD Control Center will come on and indicate “NOT READY” and the Small Mug Button will also flash. NOTE: A K-Cup should not be used for this Sequence.
8.Press the Small Mug Button (fig. 3).
NOTE: If the Water Reservoir is empty or not in place on the Brewer, the LCD Control Center will also indicate “ADD WATER.” None of the buttons will be activated until water is added to the Water Reservoir.
fig 4
NOT READY
fig 5
READY
TO BREW
9.The Brewer will automatically fill the internal tank with water and then the water will be heated. This will take about 4 minutes. During the heating period, “NOT READY” (fig. 4) is displayed on the LCD Control Center. Do not lift Brewer Handle during this ‘heating period’. Once the water is heated, “READY” will be displayed and the Small Mug Button will flash (fig. 5).
NOTE: You may see small amounts of water coming from the Vent and dripping into the
Water Reservoir during this and subsequent heat- ing — this is normal.
10.Press the Small Mug Button to start a cleansing brew. Pour the hot water into the sink.
11.The one-time set-up process is now complete and you are ready to brew!
NOTE: The Brewer may take 15 seconds between brews and then “READY TO BREW” will be displayed.
Small
Mug
Ready to Brew Your First Cup
fig 6
1. LCD Control Center will indicate “READY TO BREW”.
2. Place a cup or mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup Holder
will open toward you (fig. 6).
4. Select a K-Cup® portion pack.
NOTE: Do not remove the foil lid or puncture the K-Cup.
5. Place a K-Cup portion pack in the K-Cup Holder (fig. 7).
CAUTION: There are two sharp needles that puncture the K-Cup, one above the K-Cup Holder
and the other in the bottom of the K-Cup Holder.
fig 7 To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
6. Lower the Handle to close the Lid over the K-Cup Holder. (When it is closed completely, the LCD Control Center will indicate “READY TO BREW” and the Small Cup, Small Mug and Large Mug Buttons will flash up to 60 seconds.)
7
SECTION 1 Set-Up & First Brew
Small Cup
(5.25 oz.)
Small Mug
(7.25 oz.)
Large Mug
(9.25 oz.)
Brewing Your First Cup (Continued)
7.Choose the brew size of coffee, tea or hot cocoa by pressing the button that indicates your choice. The Large Mug choice will yield a 9.25 oz. serving, the Small Mug choice will yield a 7.25 oz. serving, and the Small Cup choice will yield
a 5.25 oz. serving.
NOTE: If you do not push the Brew Buttons in 60 seconds, the LCD Control Center will return to “READY TO BREW” and the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew Buttons by raising and lowering the Handle completely.
8.The LCD Control Center will now display the word “BREWING” and the brew size you selected will be solid blue.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Assembly Housing during the brew process.
9.There may be a short pause prior to coffee being dispensed. The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K-Cup.
10.Lift the Handle, remove and dispose of the used K-Cup.
CAUTION: K-Cup will be hot.
11. Enjoy your first cup of Keurig Brewed® gourmet coffee, tea or hot cocoa!
12. Your Brewer may display “NOT READY” as it heats water for the next brew cycle. The “READY TO BREW” indication will return to the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will fill in preparation for the next brew. The pump will make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop brewing after the process has started, press the Power Button to turn the Brewer “OFF.” The flow of coffee, tea or hot cocoa will stop, the heating element will shut off, and the blue lights illuminating the brew buttons and Water Reservoir will disappear.
NOTE: You may get less coffee, tea or hot cocoa in your cup during your next brew. We recommend that you perform a cleansing brew with water-only after a terminated brew. Then your NEXT brew will be the volume you have selected.
8
Adding Water
fig. 8
NOT READY
ADD
WATER
The LCD Control Center of your Brewer will indicate when the water level in the Water Reservoir is low or if the Water Reservoir has been removed by displaying the words “ADD WATER” (fig. 8). The blue light in the Water Reservoir will also blink when water needs to be added. The Brewer will not allow you to brew when “ADD WATER” is displayed.
The Water Reservoir can be filled in two ways.
1.Lift off the Water Reservoir Lid and pour water directly into the Water Reservoir while it is still attached to the Brewer, then replace the Lid.
2.Remove the Water Reservoir from Brewer by first removing Lid from the Water Reservoir, then lifting the Water Reservoir straight up and away from Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid.
IMPORTANT: Do not remove the Water Reservoir during the brewing process.
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet, for use in cooking, for making soups, etc. Simply raise and lower
the Handle on the Brewer without adding a K-Cup. The LCD Control Center will display “READY TO BREW” and the Small Cup, Small Mug and Large Mug Buttons will blink. Be sure to have a mug or cup on the Drip Tray Plate and then select the size you would like.
NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water brew cycle without a K-Cup.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge the water from the inner tank.
1.If there is water in the Water Reservoir, remove the Lid, then lift the Water Reservoir straight up and away from Brewer. Discard water, rinse and refill with water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2.Be sure the Brewer is turned on. Raise and lower the Handle on the Brewer without inserting a K-Cup.
3.The LCD Control Center will display “READY TO BREW” and the Small Cup, Small Mug and Large Mug Buttons will blink. Be sure to have a large mug on the Drip Tray Plate and then select the Large Mug size brew.
4.Repeat steps 2 and 3 one more time to completely purge water from inner tank.
If you are experiencing any problems with your Brewer, please contact Customer Service at 1.866.901.BREW (2739).
9
SECTION 2 Controls & Indicators (LCD Control Center)
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the LCD Control Center. NOTE: You must set the clock if you will be using the On/Off Time programming feature.
fig. 9
SET CLOCK
AUTO OFF
ON OFF TIME
BREW TEMP
MENU
Menu
Set 
Set
Hours Minutes
1.Press the Menu Button.
2.The word “OFF” will appear at the bottom of the LCD Control Center to indicate that
the clock is not set. The programming options will appear on the LCD Control Center with a small arrow pointing to “SET CLOCK” (fig. 9).
“H” (Hour) and “M” (Minute) will appear and blink.
3.Press or hold the blue Small Cup Button under the blinking “H” until you have reached the appropriate hour. If the hour has passed 12, the indicator switches from “AM” to “PM”.
4.Press or hold the blue Large Mug Button under the blinking “M” to set the minutes.
5.When you have reached the correct time, press the Menu Button five times to scroll through the remaining programming options and exit the programming mode.
6.The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is lost, follow the procedure above to reset the time as the clock will not be visible until the time is set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea or hot cocoa on your own schedule. By programming your Brewer to turn on each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee.
1.Leave it ON all the time. The Brewer can be left on all the time so that it is always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn the Brewer off at any time, simply press the Power Button. (NOTE:
Although the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.) Press the Power Button again to restore power to the Brewer. You will have to wait for the water to heat up before the Brewer is ready to brew.
fig. 10
SET CLOCK
AUTO OFF
ON OFF TIME
BREW TEMP
MENU
Menu
x2
2.Set the Brewer to Auto Off following a specified period of time after the last brew.
a.Press the Menu Button twice to program the Auto Off feature. The LCD Control Center will now display the programming options with a small arrow next to “SET AUTO OFF” (fig. 10).
b.Press or hold the blue Small Cup Button under the blinking “H” to advance 1 hour at a time, up to 9 hours.
10
fig. 11
READY
TO BREW
AUTO OFF SET
11:56 AM
MENU
c.After setting the desired Auto Off time, press the Menu Button four times to scroll through the remaining programming options and exit the programming mode. “AUTO OFF SET” (fig.
11)will now be displayed to indicate that it has been set.
d.To cancel the Auto Off feature, press the Menu Button twice to reach the Auto Off programming mode. Press and release the Small Cup Button under the blinking “H” to advance one hour at a time until “OFF” is displayed.
3.Program your Brewer for a specific On/Off Time. NOTE: To use this programming feature, the clock must be set to the correct time. The clock will not be displayed unless the time is set.
fig. 12
CLOCK
AUTO OFF
SET ON TIME
BREW TEMP
11:56AM
PM
MENU
a.After setting the correct time (required), press the Menu Button three times to program the On Time feature. The LCD Control Center will show the programming options with a small arrow next to “SET ON TIME” (fig. 12).
b.Press or hold the blue Small Cup Button under the “H” to scroll through the hours to your desired “ON TIME” hour.
c.Press or hold the blue Large Mug Button under the “M” to scroll through the minutes to your desired “ON TIME” minutes.
d.After setting the desired time, press the Menu Button to save the “ON TIME” and move to the “SET OFF TIME” (fig. 13).
fig. 13
CLOCK
AUTO OFF
SET OFF TIME
BREW TEMP
AM
PM
MENU
fig. 14
READY
TO BREW
AUTO OFF SET
ON TIME SET
11:56 AM
MENU
e.If you want to set an “OFF TIME”, repeat the procedure above in steps b & c to set your desired “OFF TIME”.
f.To complete the process, press the Menu Button two more times to exit the programming mode. The Control Center will now indicate the options you have set.
g.The On Time and Off Time functions operate independently from one another. To cancel either set function, follow the steps above and use the “H” and “M” buttons to advance to 12:00 AM. Make sure the M button is set to :00, then change the “H” button. When you reach 12:00 AM, the Control Center will display “OFF” and the function will be disabled.
EXAMPLE: If you chose to set the On Time at 6:15 AM and the Off Time for 10:00 PM, then the Brewer will be “READY TO BREW” and maintain hot water in the tank during that time so that it is always ready for you to brew. If you wanted to
brew outside this window, simply press the Power Button and you can brew as soon as the water is heated and the “READY TO BREW” indicator is displayed on the LCD Control Center.
NOTE: The “AUTO OFF” Timer and the On/Off Time programming options operate independently but can also be programmed to work together. For example, you can set the On Time function to turn on at 7:00 AM and then set the Auto Off Timer function to turn off the Brewer two hours after the last brew (fig. 14).
11
Loading...