USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new PEliteatinumB40 KeurigB70Keurig® Brewer® Brewer
COMMENT UTILISER VOTRE CAFETIÈRE
MANUEL D’UTILISATION : Tirez le meilleur de votre nouvelle cafetière Elite B40 de Keurig®
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic safety precautions should be followed, including the following:
1.Read all instructions before using.
2.Do not touch hot surfaces. Use handles and knobs when available.
3.This appliance must be properly installed and located in accordance with these instructions before it is used.
4.The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock or injury to persons.
5.Do not place on or near a hot gas or electric burner, or in a heated oven.
6.Do not use outdoors.
7.To protect against fire, electric shock and injury do not immerse cords, plugs, or the appliance in water or any other liquid.
8.Do not overfill the Water Reservoir with water.
9.Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide.
10.Turn off and unplug the Brewer before cleaning or maintenance. Allow to cool
before putting on or taking off parts and before cleaning the appliance.
11.For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuses or tripping a circuit breaker.
12.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is damaged in any manner. Contact Keurig® Customer Service to report any malfunction of or damage to the Brewer.
13.Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
14.To disconnect, press the Power Button on the top of the Brewer to ‘OFF’ status and then remove the plug from the wall outlet.
15.Close supervision is necessary when any appliance is used by or near children.
16.Do not lift the Handle to open the Lid of the Brewer while brewing is in progress.
17.Always keep the Water Reservoir Lid on
the Water Reservoir unless you are refilling it.
18.This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using
a 3-hole properly grounded outlet. In the
event of an electrical short circuit, grounding reduces the risk of electrical shock.
19.If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
21.Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
22.Do not use the appliance for other than its intended use.
Save These
Instructions.
WARNING TO USERS AND PARENTS
1.DO NOT permit children to use brewer unless there is adult supervision. Brewer dispenses very hot water.
2.SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER USING A HOT COCOA K-CUP, RUN a Hot Water Brew Cycle without a K-Cup to avoid the possibility of clogging the exit needle. DO NOT assume the next user will do this.
2
CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Assembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over un-
intentionally; and (3) the extension cord must include a 3-prong grounding plug. THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
WARNINGTHIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR !
ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
Elite — Model B40
Using Your Brewer
SET-UP |
|
Helpful Hints......................................................................................... |
4 |
Unpacking............................................................................................. |
4 |
Features................................................................................................ |
5 |
SECTION 1 — SET-UP & FIRST BREW |
|
Set-Up & First Brew............................................................................ |
6 |
SECTION 2 — CONTROLS & INDICATORS |
|
Programming Auto Off Timer Feature........................................... |
10 |
SECTION 3 — CLEANING & MAINTENANCE |
|
Cleaning.............................................................................................. |
10 |
De-Scaling.......................................................................................... |
11 |
Storage................................................................................................ |
12 |
SECTION 4 — TROUBLESHOOTING.................................................. |
13 |
SECTION 5 — WARRANTY................................................................. |
14 |
Pour des directives en français, veuillez vous reporter à la page 15.
Record your Brewer Serial Number here.
Removing the serial number label from the Brewer will void warranty.
3
Set-up
Helpful Hints
1.Keep your Brewer turned ‘ON’ at all times.
To brew a fresh cup of coffee, tea or hot cocoa anytime you want, we suggest you keep your Brewer turned ‘ON’ all the time. However, you can set the Brewer to automatically turn off two hours after your last brew. Follow the simple instructions on page 10 to make using the Brewer convenient for you.
2.For the best tasting gourmet coffee, tea or hot cocoa Keurig® recommends using bottled or filtered water.
Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee such as chlorine or other mineral taste, we recommend you consider using bottled water or water from a filtration system.
3.Customize the Size, Flavor & Brew That’s Perfect for You.
With the choice of over 200 varieties of K-Cups and 2 brew sizes (Small Mug-7.25 oz. and Large Mug-9.25 oz.) your Keurig Brewer gives you endless options to customize the size, flavor and brew that’s perfect for you. For a strong, intense cup, select an Extra Bold K-Cup (with up to 30% more ground coffee than regular
varieties) and brew size that’s right for you. The smaller the brew size, the more intense flavor in your cup. The larger the brew size, the less intense flavor in your cup.
4.Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other appliances, your Brewer may not function properly. The Brewer should be operated on its own circuit, separate from other appliances.
5.Brewing into a travel mug.
To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base.
6.De-scale Brewer regularly.
Please see page 12 for instructions.
Unpacking Instructions
1.Place Brewer box on a large steady surface (such as a table or countertop) or on the floor. Open the box.
2.Remove enclosed literature.
3.Turn the box on its side with front of box face down.
4.Reach into the box and grasp the plastic bag that contains the Brewer.
5.Carefully pull the plastic bag (and packaging materials) toward you and out of the box. The Brewer will still be encased in the polyfoam and be on its side.
6.Remove the top polyfoam packaging material.
7.Carefully lift Brewer off of the bottom polyfoam and place it upright on a flat, steady surface.
8.Lift plastic bag off of Brewer.
9.Record the serial number for this Brewer
on page 3 of this Guide. The serial number can be found on the bottom of this box or on the Brewer, behind the Drip Tray Assembly (when removed).
10.Place the Brewer upright on a flat, steady surface. Remove tape holding Water Reservoir in place.
We recommend you save all packing materials in case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away from children.
4
Features Elite — Model B40 Brewer
|
D |
G |
|
|
|
A |
|
|
|
M |
|
|
|
H |
B |
C |
|
|
|
|
|
N |
|
|
I |
|
|
|
L |
B40 Brewer
A.Water Reservoir Lid
B.Water Reservoir
C.Water Reservoir Lock Tab Slots
D.Handle
E.Funnel
F.K-Cup® Portion Pack Holder (E and F are the K-Cup Holder Assembly)
G.Lid
H.K-Cup Portion Pack Assembly Housing
I.Housing
J.Drip Tray Plate
K.Drip Tray
L.Drip Tray Base
M.Vent
N.Power Cord
5
|
|
|
W |
|
|
|
ADD WATER |
V |
|
|
|
|
|
|
|
|
DE-SCALE |
U |
T |
|
|
HEATING |
|
|
|
F |
|
S |
|
|
AUTO OFF |
|
||
|
|
|
|
|
E |
|
POWER |
|
Q |
R
J |
|
|
O |
P |
|
K |
||
|
Controls and Indicators
O. Small Mug Button |
T. Auto Off Light (Green) |
P. Large Mug Button |
U. Heating Light (Red) |
Q. Power Button |
V. De-Scale Light (Red) |
R. Power Light (Green) |
W. Add Water Light (Blue) |
S. Auto Off Button |
|
SECTION 1 Set-Up & First Brew
IMPORTANT: You cannot use your Keurig Brewer until it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures below freezing, allow Brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold brewer will not operate.
fig. 1 Setting Up Your Brewer
1. Unwrap cord and plug the Brewer into a grounded outlet. Remove all pieces of packing tape.
2. Place a Large Mug (10 oz. minimum) on the Drip Tray Plate.
3. Remove the Water Reservoir from Brewer by first removing Lid from Reservoir (fig. 1), then lifting Reservoir straight up and away from Brewer (may be tight). Rinse with fresh water.
4.Fill Water Reservoir with bottled or filtered water so that the water level reaches the line just below the top edge of the clear viewing area. (Be careful not to over fill.)
6
Lock Tabs fig. 2
fig. 3
ADD WATER 
DE-SCALE 
HEATING 
AUTO OFF 
POWER 
Small Mug
5.Place Water Reservoir base into the left side of the Brewer and be sure the Water Reservoir Lock Tabs engage with the Brewer (fig. 2). Replace Lid on Water Reservoir.
6.Press Power Button found on upper right panel of the Brewer. The green light next to the Power Button will become illuminated.
NOTE: A K-Cup should not be used for this Sequence.
NOTE: If the Water Reservoir is empty or not in place on the Brewer, the blue light next
to ‘ADD WATER’ on the LED Control Center will be illuminated. The Small Mug Button will
not be activated until water is added to the Water Reservoir.
7.The Brewer will automatically fill with water and then the water will be heated. This will take about 4 minutes. During the heating period the red light next to ‘HEATING’ on the LED Control Center will become illuminated. Once the water is heated, the red light will turn off and the Small Mug Button will flash.
NOTE: Do not lift Brewer Handle during this ‘heating period’.
NOTE: You may see small amounts of water coming from the Vent and dripping |
fig 5 |
|
|
|
|
|
into the Water Reservoir during this and subsequent heating – this is normal. |
|
|
|
|
|
|
8. Press the Small Mug Button to start a cleansing brew (fig. 3). Pour the hot |
|
|
|
|
|
|
water into the sink. |
|
|
|
|
|
|
9. The Brewer may take 15 seconds to reheat water between brews during |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
which time the red light next to ‘HEATING’ on the LED Control Center may |
|
|
|
|
|
|
be illuminated. When the water has heated, the red light will turn off. |
|
|
|
|
|
|
10. The one-time set-up process is now complete and you are ready to brew! |
|
|
|
|
|
|
Ready to Brew Your First Cup
fig 4 |
1. The green light next to the Power Button on |
|
the LED Control Center will be illuminated to |
|
|
|
indicate the Brewer is powered on. |
|
|
2. Place a cup or mug on the Drip Tray Plate. |
|
|
3. Lift the Handle and the K-Cup Holder |
|
|
will open toward you. (fig. 4) |
|
|
4. Select a K-Cup® portion pack. |
|
|
NOTE: Do not remove the foil |
|
|
lid or puncture the K-Cup. |
Small Mug |
|
5. Place a K-Cup portion pack |
(7.25 oz.) |
|
|
|
|
in the K-Cup Holder. (fig 5.) |
|
|
CAUTION: There are two sharp needles that |
|
|
puncture the K-Cup, one above the K-Cup Holder |
Large Mug |
|
and the other in the bottom of the K-Cup Holder |
(9.25 oz.) |
To avoid risk of injury, do not put your fingers in the K-Cup Holder.
6.Lower the Handle completely to close the Lid.
7.Select your brew size: The Small Mug choice will yield a 7.25 oz. serving and the Large Mug will yield a 9.25 oz. serving.
NOTE: If you do not push a Brew Button in 60 seconds, the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew Buttons by raising and lowering the Handle completely.
8.The blue light behind the Brew Button you choose on the LED Control Center will remain lit while brewing.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Assembly Housing during the brew process.
9.There may be a short pause before the brewing process begins. The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K-Cup.
10.Lift the Handle, remove and dispose of the used K-Cup. CAUTION: K-Cup will be hot.
11.Enjoy your first cup of Keurig Brewed® gourmet coffee, tea or hot cocoa!
7
SECTION 1 Set-Up & First Brew
Brewing Your First Cup (Continued)
12.The red light next to ‘HEATING’ on the LED Control Center may be lit as the water is heated for the next brew cycle. The Brewer will be ready for use in approximately 15 seconds.
NOTE: Following the brew, your Brewer will fill in preparation for the next brew. The pump may make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop the brewing after the process has started, press the Power Button to turn the Brewer ‘OFF’. The flow of coffee or tea will stop, the heating element will shut off and the green light next to the Power Button will disappear.
NOTE: You may get less coffee, tea or hot cocoa in your cup during your next brew. We recommend that you perform a cleansing brew with water only after a terminated brew. Then your NEXT brew will be the proper volume.
Adding Water
fig. 6
ADD WATER 
DE-SCALE 
HEATING 
AUTO OFF 
The LED Control Center of your Brewer will indicate when the water level in the Water Reservoir is low or if the Water Reservoir has been removed by illuminating the blue light next to ‘ADD WATER’ (fig. 6). The Brewer will not allow you to brew when the blue ‘ADD WATER’ light is illuminated.
The Water Reservoir can be filled in two ways.
POWER |
1. Lift off the Water Reservoir Lid and pour |
|
water directly into the Water Reservoir |
|
while it is still attached to the Brewer, |
|
then replace the Lid. |
2.Remove the Water Reservoir from Brewer by first removing Lid from the Water Reservoir, then lifting the Water Reservoir straight up and away from Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid.
IMPORTANT: Do not remove the Water Reservoir during the brewing process.
8
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa in a packet, for use in cooking, for making soups, etc. Simply raise and lower the Handle on the Brewer without adding a K-Cup® portion pack. The blue lights behind the Brew Buttons on the LED Control Center will flash. Be sure to have a mug or cup on the Drip Tray Plate and then press a Brew Button.
NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water brew cycle without a K-Cup.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge the water from the inner tank.
1.If there is water in the Water Reservoir, remove the Lid, then lift Reservoir straight up and away from Brewer. Discard water, rinse and refill with water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in Reservoir, simply refill.)
2.Be sure the Brewer is turned on. Raise and lower the Handle on the Brewer without inserting a K-Cup and wait until the red light next to ‘HEATING’ turns off.
3.The blue lights behind the Brew Buttons on the LED Control Center will flash. Be sure to have a mug or cup on the Drip Tray Plate and then press a Brew Button.
4.Repeat steps 2 and 3 two more times to completely purge water from inner tank.
If you are experiencing any problems with your Brewer, please contact Customer Service at 1.866.901.BREW (2739).
9
Loading...