Kenwood KDC-8021, KDC-M907, KDC-M9021, KDC-PSW9521 User Manual

KDC-PSW9521 KDC-M907 KDC-M9021 KDC-8021

CD-RECEIVER

INSTRUCTION MANUAL

COMPACT

DIGITAL AUDIO

© B64-2834-00/00 (EW)

English

Contents

Safety precautions......................	3	CD/MP3/WMA/External disc		Dimmer
About RDS ..................................	5	control features .....................	23	OFF Wait Time Setting
Notes on playing MP3/WMA.......	6	Playing CD & MP3/WMA		System Q
About CDs...................................	8	Playing External Disc		Built-in Amp Mute Setting
General features	9	Fast Forwarding and Reversing		Dual Zone System
		Track Search		B.M.S. (Bass Management System)
Power
		Album Search		B.M.S. Frequency Offset
Volume
		Direct Track Search		News Bulletin with Timeout Setting
Selecting the Source
		Direct Album Search		Local Seek
System Q
		Track Repeat		Tuning Mode
Audio Control
		Album Repeat		Auto Memory Entry
Non-fading Output
		Track/Album Repeat		AF (Alternative Frequency)
Faceplate Angle Adjustment
		Track Scan		Restricting RDS Region
Speaker & Woofer Setting
		Random Play		(Region Restrict Function)
Speaker Setting
		Magazine Random Play		Auto TP Seek
Switching Full Screen Display
		Album Select		Monaural Reception
Switching the Standby Display
		DNPP (Disc Name Preset Play)		Auxiliary Input Display Setting & Disc
Switching Upper and Lower Part Display
Theft Deterrent Faceplate		Disc Naming (DNPS)		Naming
Hiding the Control Panel		Text/Title Scroll		Text Scroll
TEL Mute		Menu system	29	Power OFF Timer
				Basic Operations of remote	38
Tuner features	17	Menu System
				Accessories	40
Tuning		Mask Key
Direct Access Tuning		Touch Sensor Tone		Installation Procedure ..............	40
Station Preset Memory		Manual Clock Adjustment		Connecting Wires
Auto Memory Entry		Date Adjustment
				to Terminals	41
Preset Tuning		Date Mode
				Installation	42
SNPP (Station Name Preset Play)		Synchronize Clock
RDS features .............................	20	Selectable Illumination		Removing the Unit....................	43
Traffic Information		Switching Display Type		Locking the faceplate
Radio Text Scroll		Switching Upper and Lower Part Display		to the unit ..............................	43
PTY (Program Type)		Icon/Spectrum analyzer Select		Troubleshooting Guide	44
		Font Type Select
Program Type preset				Specifications	49
Changing Language for PTY Function		Font Color Select

— 2 —

Safety precautions

2WARNING

2CAUTION

To prevent injury and/or fire, take the following precautions:

•Insert the unit all the way until it is fully locked in place. Otherwise it may fly out of place during collisions and other jolts.

•When extending the ignition, battery, or ground wires, make sure to use automotivegrade wires or other wires with a 0.75mm2 (AWG18) or more to prevent wire deterioration and damage to the wire coating.

•To prevent short circuits, never put or leave any metallic objects (e.g., coins or metal tools) inside the unit.

•If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.

•Make sure not to get your fingers caught between the faceplate and the unit.

•Be careful not to drop the unit or subject it to strong shock.

The unit may break or crack because it contains glass parts.

To prevent damage to the machine, take the following precautions:

•Make sure to ground the unit to a negative 12V DC power supply.

•Do not open the top or bottom covers of the unit.

•Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

•Do not subject the faceplate to excessive shock, as it is a piece of precision equipment.

•When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.

•To prevent short circuits when replacing a fuse, first disconnect the wiring harness.

•Do not place any object between the faceplate and the unit.

•During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit.

•Do not apply excessive force to the moving faceplate. Doing so will cause damage or malfunction.

•Do not apply excessive force to the open faceplate or place objects on it. Doing so will cause damage or breakdown.

IMPORTANT INFORMATION

About CD players/disc changers connected to this unit

KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit.

Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players.

Note that any KENWOOD disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit.

Unsupported connection may result in damage.

Setting the "O-N" Switch to the "N" position for the applicable KENWOOD disc changers/ CD players.

The functions that can be used and the information that can be displayed will differ depending on the models being connected.

You can damage both your unit and the CD changer if you connect them incorrectly.

Do Not Load 8-cm (3-in.) CDs in the CD slot

If you try to load an 8-cm CD with its adapter into the unit, the adapter might separate from the CD and damage the unit.

— 3 —

English

Safety precautions

NOTE

•If you experience problems during installation, consult your Kenwood dealer.

•If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. After you press the reset button, the Mask Key will be needed to restart the unit. If the unit still fails to operate properly after the Reset button has been pressed, contact your local KENWOOD dealer for assistance.

•Press the reset button if the Disc auto changer fails to operate correctly. Normal operation should be restored.

•The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation.

When using the unit for the first time

In order to deactivate the demonstration mode. Transmit the Mask Key's signal. (page 30)

	Lens Fogging
	Right after you turn on the car heater in cold
	weather, dew or condensation may form on
	the lens in the CD player of the unit. Called
	lens fogging, CDs may be impossible to play.
Reset button	In such a situation, remove the disc and wait
	for the condensation to evaporate. If the unit
	still does not operate normally after a while,
• If you send products in for repair that include	consult your Kenwood dealer.
a mask key, make sure to present the unit
together with the mask key.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off.

Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.

Cleaning the CD Slot

As dust can accumulate in the CD slot, clean it occasionally. Your CDs can get scratched if you put them in a dusty CD slot.

— 4 —

The marking of products using lasers (Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.

About RDS

RDS (Radio Data System)

When listening to an RDS station, the program service name of the station is displayed, advising you quickly which station is being received.

RDS (Radio Data System) stations also transmit alternative frequency data for the same station. When you are making long trips, this function automatically switches to the particular frequency with the best reception for the particular network of stations that you want to listen to. The data is automatically stored, allowing you to switch quickly to another RDS stations, broadcasting the same program, that has better reception. These include stations stored in the station preset memory that you often listen to.

Enhanced Other Network

Stations that offer <Enhanced Other Network> also transmit information about other RDS stations that have traffic information. When you are tuned to a station that is not transmitting traffic information, but another RDS station starts transmitting a traffic bulletin, the tuner automatically switches to the other station for the duration of the bulletin.

Alarm

When an emergency transmission (announcing disasters, etc.) is sent, all current functions are interrupted to allow the warning to be received.

— 5 —

English

Notes on playing MP3/WMA(KDC-PSW9521)/ MP3(KDC-M907/KDC-M9021)

This unit can play MP3(MPEG1, 2 Audio Layer 3)/WMA. Note,

Entering ID3 tag and Contents

however, that the MP3/WMA recording media and formats

Description

acceptable are limited. When writing MP3/WMA, pay attention to

The Displayable ID3 tag is ID3 version

the following restrictions.

1.x.

Acceptable media

For the character code, refer to the List

The MP3/WMA recording media acceptable to this unit are CD-ROM,

of Codes.

CD-R, and CD-RW.

When using CD-RW, do full format not quick format to prevent

Entering file and folder names

malfunction.

The code list characters are the only file

Acceptable medium formats

names and folder names that can be

The following formats are available for the media used in this unit. The

entered and displayed.

maximum number of characters used for file name including the

If you use any other character for entry, the file and folder names are

delimiter (".") and three-character extension are indicated in

not displayed correctly. They may neither be displayed correctly

parentheses.

depending on the CD writer used.

• ISO 9660 Level 1 (12 characters)

The unit recognizes and plays only those MP3/WMA which have the

• ISO 9660 Level 2 (31 characters)

MP3/WMA extension (.MP3/.WMA).

• Joliet (64 characters)

A file with a name entered with characters not on the code list

• Romeo (128 characters)

may not play correctly.

Up to 200 characters can be displayed in the long file name format.

For a list of available characters, see the instruction manual of the

Writing files into a medium

writing software and the section Entering file and folder names below.

The media reproducible on this unit has the following limitations:

When a medium containing MP3/WMA data is loaded, the unit checks

all the data on the medium. If the medium contains a lot of folders or

• Maximum number of directory levels:

8

non-MP3/WMA files, therefore, it takes a long time until the unit starts

• Maximum number of files per folder:

255

playing MP3/WMA.

• Maximum number of characters for folder name: 64

In addition, it may take time for the unit to move to the next

• Maximum number of folders: 50

MP3/WMA file or a Track Search or Album Search may not be

MP3/WMA written in the formats other than the above may not be

performed smoothly.

successfully played and their file names or folder names are not

Loading such a medium may produce loud noise to damage the speakers.

properly displayed.

• Do no attempt to play a medium containing a non-MP3/WMA file

Settings for your MP3/WMA encoder and CD writer

with the MP3/WMA extension.

Do the following setting when compressing audio data in WMA data

The unit mistakes non-MP3/WMA files for MP3/WMA data as long as

with the WMA encoder.

they have the MP3/WMA extension.

• Transfer bit rate: 64k —192 kbps

• Do not attempt to play a medium containing non MP3/WMA.

• Sampling frequency: 32k, 44.1k, 48k Hz

When you use your CD writer to record MP3/WMA up to the maximum disc capacity, disable additional writing. For recording on an empty disc up to the maximum capacity at once, check Disc at Once.

— 6 —

MP3/WMA playing order

When selected for play, Album Search, Track Search, or for Album Select, files and folders are accessed in the order in which they were written by the CD writer.

Because of this, the order in which they are expected to be played may not match the order in which they are actually played. You may be able to set the order in which MP3/WMA are to be played by writing them onto a medium such as a CD-R with their file names beginning with play sequence numbers such as "01" to "99", depending on your CD writer.

For example, a medium with the following folder/ file hierarchy is subject to Album Search, Track Search, or Album Select as shown below.

Example of a medium's folder/file hierarchy

When a Track Search is executed with file ¡$ being played ...

Current		Operation of the button
file number	4 Button	¢ Button
	Beginning of file

When an Album Search is executed with file ¡$ being played ...

Current	Operation of the button
folder number	AM Button	FM Button

When Album Select is selected with file ¡$ being played to move

from folder to folder ...

Current		Operation of the button
folder number	4 Button	¢ Button	AM Button	FM Button

Folder

File

Root

Level 1	Level 3
Level 2	Level 4

— 7 —

English

About CDs

Handling CDs

• Don’t touch the recording surface of the CD.

•CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc.

•Don’t stick tape etc. on the CD.

Also, don’t use a CD with tape stuck on it.

When using a new CD

If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc.

Burrs

Burrs

CD accessories

Don’t use disc type accessories.

CD cleaning

Clean from the center of the disc and move outward.

Removing CDs

When removing CDs from this unit pull them out horizontally.

CDs that can’t be used

• CDs that aren’t round can’t be used.

•CDs with coloring on the recording surface or that are dirty can’t be used.

•Don’t use CDs without disc mark

.

•A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.)

CD storage

•Don’t place them in direct sunlight (On the seat or dashboard etc.) and where the temperature is high.

•Store CDs in their cases.

—8 —

General features

AM/

NF VOL FM

Power

Turning ON the Power

Turn the vehicle ignition ON.

The faceplate reverses and control panel is displayed.

Turning OFF the Power

Turn the vehicle ignition OFF.

When the set time for removing the faceplate (page 16) lapses, the faceplate reverses and the control panel is hidden.

4	¢	SRC Q/	MENU	ANG
		AUD

Do not apply force to the faceplate during operation. It can cause damage.

The first time the unit is used it is necessary to cancel the Demonstration mode with the Mask key (page 30). If the Demonstration mode isn't canceled, the unit can't be used normally.

KDC-PSW9521

LOUD indicator

KDC-M907/ KDC-M9021/ KDC-8021

I N

P / S

AT T

S T

L O U D

R D S

T I

Volume

Increasing Volume

Turn the [VOL] knob clockwise.

Decreasing Volume

Turn the [VOL] knob counterclockwise.

LOUD indicator

— 9 —

English

General features

Selecting the Source

Press the [SRC] button.
Source required	Display
Tuner	"TUNER"
CD	"COMPACT DISC"/"CD"
External disc	"DISC-CH"/"DISC"
Auxiliary input	"AUX"
Standby (Illumination only mode)	"ALL OFF"

•For Auxiliary input one of the below optional accessories is necessary.

-KCA-S210A

-CA-C1AX

-CD changer with an Auxiliary input function installed.

•This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicles battery. The time until full power OFF can be set in <Power OFF Timer> (page 37).

Sound setting	Display
Flat	"FLAT"
User memory	"User Preset"
Rock	"ROCK"
Pops	"POPS"
Easy	"EASY"
Top 40	"TOP 40"
Jazz	"JAZZ"

•User memory: The values set on the <Audio control> (page 10).

•Each setting value is changed with the <Speaker setting> (page 12).

First, select the speaker type with the Speaker setting.

System Q

You can recall the best sound setting preset for different types of the music.

1Select the source to set

Press the [SRC] button.

2Select the Sound type

Press the [Q] button.

Each time the button is pressed the sound setting switches.

Audio Control

1Select the source for adjustment

Press the [SRC] button.

2Enter Audio Control mode

Press the [AUD] button for at least 1 second.

3Select the Audio item for adjustment

Press the [FM] or [AM] button.

Each time the button is pressed the items that can be adjusted switch as shown below.

4Adjust the Audio item

Press the [4] or [¢] button.

— 10 —

Adjustment Item	Display	Range
Bass Center Frequency	"Bass FRQ"	60/70/80/100 or 150 Hz
Bass level	"Bass"	–8 — +8
Bass Q Factor	"Bass Q"	1.00/1.25/1.50/2.00
Bass Extend	"Bass EXT"	ON/OFF
Middle Center	"MID FRQ"	0.5/1.0/1.5/2.0 kHz
Frequency
Middle level	"MID"	–8 — +8
Middle Q Factor	"Middle Q"	1.0/2.0
Treble Center Frequency"TRE FRQ"		10.0/12.5/15.0/17.5 kHz
Treble level	"TRE"	–8 — +8
Balance	"Balance"	Left 15 — Right 15
Fader	"Fader"	Rear 15 — Front 15
Non-Fading level*	"NF Level"	–15 — +15
Front High Pass Filter*	"HPF Front"	Through/40/60/80/100/
		120/150/180/220 Hz
Rear High Pass Filter*	"HPF Rear"	Through/40/60/80/100/
		120/150/180/220 Hz
Non-Fading	"LPF NF"	50/80/120/Through Hz
Low Pass Filter*
Non-Fading Phase*	"NF Phase"	Normal (0°)/Reverse
		(180°)
Volume offset	"Volume Offset"	–8 — ±0
Loudness	"LOUD"	ON/OFF

•According to the Bass Q Factor setting value, the frequencies that can be set in Bass Center Frequency change as shown below.

Bass Q Factor	Bass Center Frequency
1.00/1.25/1.50	60/70/80/100
2.00	60/70/80/150

•When the bass extend is set to ON, low frequency response is extended by 20%.

•Volume offset: Each source's volume can be set as a difference

from the basic volume.

• Loudness: Compensating for low and high tones during low volume.

(KDC-PSW9521) The graphic is displayed when Loudness is ON, and is switched OFF when Loudness is OFF.

• * :Function of the KDC-PSW9521/ KDC-M907/ KDC-M9021

5Exit Audio Control mode

Press the [AUD] button.

Function of the KDC-PSW9521/KDC-M907/KDC-M9021

Non-fading Output

Turning the Non-fading output ON or OFF.

Press the [NF] button for at least 1 second.

Each time the button is pressed Non-fading output switches ON or OFF.

When it’s ON, "NF ON" is displayed.

Faceplate Angle Adjustment

Press the [ANG] button for at least 1 second.

Do not apply excessive force to the faceplate. It can cause damage.

— 11 —

English

General features

Function of the KDC-PSW9521/KDC-M907/KDC-M9021 In Woofer setting mode

Speaker & Woofer Setting						Woofer type	Display
Speaker setting allows the System Q settings to be fine-tuned						OFF	"Woofer OFF"
according to the type of speakers.						12 in. A type	"12in type A"
Woofer setting allows for Network configuration according to the						10 in. A type	"10in type A"
type of subwoofers.						12 in. B type	"12in type B"
1 Enter Standby						10 in. B type	"10in type B"
						12 in. C type	"12in type C"
	Press the [SRC] button.
						10 in. C type	"10in type C"
	Select the "ALL OFF" display.
						8 in. type	"8inch"
2 Enter Speaker & Woofer Setting mode
						12 in. D type	"12in type D"
	Press the [Q] button.					10 in. D type	"10in type D"
	"Speaker Setting" is displayed.				5 Exit Speaker & Woofer Setting mode
3 Select the Setting mode
						Press the [Q] button.
	Press the [FM] or [AM] button.
	Each time the button is pressed it switches between Speaker
	setting mode and Woofer setting mode.
4 Select the Speaker and Woofer type							Function of the KDC-8021
	Press the [4] or [¢] button.
	Each time the button is pressed the setting switches as shown				Speaker Setting
	below.				Fine-tuning so that the System Q value is optimal when setting
In Speaker setting mode
					the speaker type.
	Speaker type	Display			1 Enter Standby
	OFF	"OFF"
						Press the [SRC] button.
	For 5 & 4 in. speaker	"5/4 inch"
						Select the "ALL OFF" display.
	For 6 & 6x9 in. speaker	"6*9/6inch"
					2 Enter Speaker Setting mode
	For the OEM speaker	"O.E.M."
						Press the [Q] button.
						"Speaker Setting" is displayed.
					3 Select the Speaker type
						Press the [4] or [¢] button.
						Each time the button is pressed the setting switches as shown
						below.

— 12 —

Speaker type		Display
OFF		"OFF"
For 5	& 4 in. speaker	"5/4inch"
For 6	& 6x9 in. speaker	"6*9/6 inch"
For the OEM speaker		"O.E.M."

4Exit Speaker Setting mode

Press the [Q] button.

Switching Full Screen Display

Switching the Full screen display.

1Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

2Select Display Control mode

Press the [FM] or [AM] button.

Select the "Display Mode Select"/"Disp Mode Select" display.

3Enter Display Control mode

Press the [4] or [¢] button for at least 1 second.

4Switch the Full screen display

Press the [4] or [¢] button.

Each time the button is pressed the display switches.

Information

Demonstration Spectrum Analyzer 1 Spectrum Analyzer 2 Spectrum Analyzer 3

Graphic 1 (KDC-PSW9521)

Spectrum Analyzer 4 (KDC-M907/ M9021/ 8021) Graphic 2 (KDC-PSW9521)

Spectrum Analyzer 5 (KDC-M907/ M9021/ 8021)

5Exit Display Control mode

Press the [MENU] button.

Full Screen display can be selected when "Display Type C" is selected in <Switching Display Type> (page 32).

Switching the Standby Display

Switching the information displayed in Standby.

1Enter Standby

Press the [SRC] button.

Select the "ALL OFF" display.

2Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

3Select Display Control mode

Press the [FM] or [AM] button.

Select the "Display Mode Select"/"Disp Mode Select" display.

4Enter Display Control mode

Press the [4] or [¢] button for at least 1 second.

5Switch the display

Press the [4] or [¢] button.

Each time the button is pressed the display switches.

Information	Display
Demonstration	"DEMONSTRATION"
Date & Clock	"DATE"/"CLOCK"
Standby display	"ALL OFF"

6Exit Display Control mode

Press the [MENU] button.

Demonstration can be selected when "Display Type A" or "Display Type C" is selected in <Switching Display Type> (page 32).

—13 —

English

General features

Switching Upper and Lower Part Display

Switching the upper and lower part display.

1Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

2Select Display Control mode

Press the [FM] or [AM] button.

Select the "Display Mode Select"/"Disp Mode Select" display.

3Enter Display Control mode

Press the [4] or [¢] button for at least 1 second.

4Switch the Upper part display

Press the [FM] or [AM] button.

Switch the Lower part display

Press the [4] or [¢] button.

Each time the button is pressed the display switches.

The Reference for the display content is after this operation's explanation.

5Exit Display Control mode

Press the [MENU] button.

•The same information can't be displayed on the Upper part display and lower part display.

•The Upper part display and Lower part display switching can be selected when "Display Type A" is selected in <Display Mode switching> (page 32).

•When "Display Type B" is selected the Lower part display content is clock ON or OFF.

In Tuner source
Upper Part Display
	Information	Display
	Program Service name or Frequency	"BAND+ch+PS"
	Radio text	"R-TEXT"
Lower Part Display
	Information	Display
	Spectrum Analyzer (KDC-PSW9521)	"S/ANA"
	Spectrum Analyzer & Graphic	"S/ANA+GRAPHIC"
	(KDCM907/ M9021/ 8021)
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDCM907/ M9021/ 8021)
	Spectrum Analyzer	"S/ANA"
	(KDCM907/ M9021/ 8021)
	Radio text	"R-TEXT"
	Date	"DATE"
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDC-PSW9521)
	Clock & Graphic	"CLOCK+GRAPHIC"
	(KDCM907/ M9021/ 8021)

In CD/ External disc source
Upper Part Display
	Information	Display
	Track Time	"P-Time"
	Disc name	"DNPS"
	Disc title	"DISC-TITLE"
	Track title	"TRACK-TITLE"

— 14 —

Lower Part Display
	Information	Display
	Spectrum Analyzer (KDC-PSW9521)	"S/ANA"
	Spectrum Analyzer & Graphic	"S/ANA+GRAPHIC"
	(KDCM907/ M9021/ 8021)
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDCM907/ M9021/ 8021)
	Spectrum Analyzer	"S/ANA"
	(KDCM907/ M9021/ 8021)
	Track Title	"TRACK-TITLE"
	Disc Title	"DISC-TITLE"
	Disc name	"DNPS"
	Date	"DATE"
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDC-PSW9521)
	Clock & Graphic	"CLOCK+GRAPHIC"
	(KDCM907/ M9021/ 8021)

For Disc name registration refer to <Disc Naming (DNPS)> (page 28).

Function of the KDC-PSW9521/KDC-M907/KDC-M9021

In MP3/WMA source
Upper Part Display
	Information	Display
	Track Time	"P-Time"
	Disc name	"DNPS"
	Folder name	"FOLDER NAME"
	File name	"FILE NAME"
	Song title & Artist name	"TITLE/ARTIST"
	Album name & Artist name	"ALBUM/ARTIST"

Lower Part Display
	Information	Display
	Spectrum Analyzer (KDC-PSW9521)	"S/ANA"
	Spectrum Analyzer & Graphic	"S/ANA+GRAPHIC"
	(KDC-M907/ M9021)
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDC-M907/ M9021)
	Spectrum Analyzer (KDC-M907/ M9021)	"S/ANA"
	Album name & Artist name	"ALBUM/ARTIST"
	Song title & Artist name	"TITLE/ARTIST"
	File name	"FILE NAME"
	Folder name	"FOLDER NAME"
	Disc name	"DNPS"
	Date	"DATE"
	Spectrum Analyzer & Clock (KDC-PSW9521)	"S/ANA+CLOCK"
	Clock & Graphic (KDC-M907/ M9021)	"CLOCK+GRAPHIC"
	For Disc name registration refer to <Disc Naming (DNPS)> (page
28).
In Auxiliary input source
Lower Part Display
	Information	Display
	Spectrum Analyzer (KDC-PSW9521)	"S/ANA"
	Spectrum Analyzer & Graphic	"S/ANA+GRAPHIC"
	(KDC-M907/ M9021/ 8021)
	Spectrum Analyzer & Clock	"S/ANA+CLOCK"
	(KDC-M907/ M9021/ 8021 only)
	Spectrum Analyzer	"S/ANA"
	(KDC-M907/ M9021/ 8021 only)
	Date	"DATE"
	Spectrum Analyzer & Clock (KDC-PSW9521)	"S/ANA+CLOCK"
	Clock & Graphic (KDC-M907/ M9021/ 8021)	"CLOCK+GRAPHIC"

The Auxiliary input name is always displayed on the Upper part display.

— 15 —

English

General features

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you, helping to deter theft.

Removing the Faceplate

1Turn the ignition OFF or press the [SRC] button for at least 1 second.

The power turns OFF and the faceplate slides open.

2Holding the center part of the faceplate pull it out.

• When the faceplate is kept remove open, according to the <OFF Wait Time Setting> (page 33) setting, the faceplate is hidden and the power turns OFF.

•The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached.

•Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

Reattaching the Faceplate

1 Set the left side of the faceplate in the faceplate bracket.

2 Press the right side of the faceplate until it locks.

Hiding the Control Panel

Prevents tampering with the unit while your car is being serviced etc.

Hiding the control panel

Press the [SRC] button for at least 1 second.

The faceplate slides open.

When the time set in <OFF Wait Time Setting> (page 33) lapses, the faceplate is hidden and the power turns OFF.

Showing the control panel

Press the left part at the upper side of the faceplate.

The faceplate will open and show the control panel.

TEL Mute

The audio system automatically mutes when a call comes in.

When a call comes in

"CALL" is displayed.

The audio system pauses.

Listening to the audio during a call

Press the [SRC] button.

The "CALL" display disappears and the audio system comes back ON.

When the call ends

Hang up the phone.

The "CALL" display disappears and the audio system comes back ON.

— 16 —