Kenwood KDC-X302, KDC-D372BT, KDC-BT372U, KDC-BT22, KDC-BT32 User Manual

KDC-X302 KDC-BT372U KDC-BT340U

KDC-BT32 KDC-MP372BT KDC-BT272U KMR-D372BT KDC-BT22

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X302/KDC-BT372U/KDC-BT340U/KDC-BT32/KDC-BT272U/KDC-BT22/KDC-MP372BT/KMR-D372BT Serial number

US Residents Only

Register Online

Register your Kenwood product at http://www.kenwood.com/usa/

© 2017 JVC KENWOOD Corporation

B5A-2095-10 (KN)

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.

A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

i

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

(1)This device may not cause interference; and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1)l’appareil ne doit pas produire de brouillage;

(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Contains Bluetooth Module	FCC ID:	ZWY8811X
	IC ID:	12033A-8811X

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1)es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2)este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada”

ii

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2

License

1.The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2.The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3.The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4.The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1.When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2.The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

1.Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2.The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

iii

Article 8	Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event:

(1)when the User violated any provision of this Agreement; or

(2)when a petition has been filed against the User for an attachment,

provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1.The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2.The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1.It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2.The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3.The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1.In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2.Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3.The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Copyright (c) 2009-2012 Petri Lehtinen <[e-mail]>

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

iv

CONTENTS

BEFORE USE	2
BASICS	3
GETTING STARTED	4

1Select the display language and cancel the demonstration

2 Set the clock and date

3 Set the initial settings

RADIO	6
CD/USB/iPod/ANDROID	8
AUX	10
Pandora®	11
iHeartRadio®	12
Spotify	13
SiriusXM® Radio	14
BLUETOOTH®	17
AUDIO SETTINGS	24
DISPLAY SETTINGS	27
LEARNING STEERING REMOTE
CONTROL	28
TROUBLESHOOTING	29
REFERENCES	32
Maintenance
More information
INSTALLATION/CONNECTION	35
SPECIFICATIONS	39

BEFORE USE

IMPORTANT

•To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

•Please keep the manual in a safe and accessible place for future reference.

WARNING

•Do not operate any function that takes your attention away from safe driving.

•Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery.

If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•Avoid using the external device if it might hinder safe driving.

•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•USB rating is indicated on the main unit. To view, detach the faceplate. ( 3)

•Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected (37). Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•Do not leave the remote control in hot places such as on the dashboard.

•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•Operations are explained mainly using buttons on the faceplate of .

•English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)

•[XX] indicates the selected items.

•( XX) indicates references are available on the stated page.

2ENGLISH

BASICS
Faceplate				Remote control (RC-406) (supplied for		)
Volume	Loading	Display window			Remote sensor (Do not expose to bright
					sunlight.)
knob	slot
		Lights up when			Pull out the insulation sheet
		Bluetooth
					when using for the first time.
		connection is
		established.*1
		(	17)	/	/	/	:
				Can be remotely controlled with an optionally purchased
Detach button	Flashes when the unit enters searching status.*1			remote control.
				/	/	: Remote control
				functions are not available.

Attach

Detach

How to reset

How to replace the battery

To	On the faceplate		On the remote control
Turn on the power	Press	.	Press and hold SRC to turn off the power.
	• Press and hold to turn off the power. *2		( Pressing SRC does not turn on the power. )
Adjust the volume	Turn the volume knob.		Press	or	.
			• Press and hold		to continuously increase the volume to 15.
			Press ATT during playback to attenuate the sound.
			• Press again to cancel.
Select a source	Press	repeatedly.	Press SRC repeatedly.
Change the display information*3	Press DISP repeatedly. ( 34, 35)		( Not available )

*1 *2 *3

Only for / / / / .

For : The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off). For : You can also turn off the display information by pressing DISP repeatedly.

ENGLISH 3

GETTING STARTED

1Select the display language and cancel the demonstration

When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB”

1Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob.

[ENG] is selected for the initial setup.

Then, (except for ) the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.

2Press the volume knob.

[YES] is selected for the initial setup.

3Press the volume knob again.

“DEMO OFF” appears.

2Set the clock and date

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [CLOCK], then press the knob.

To adjust the clock

3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.

4Turn the volume knob to make the settings, then press the knob.

Hour Minute

5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob.

To set the date

7 Turn the volume knob to select [DATE FORMAT], then press the knob.

8Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob.

9 Turn the volume knob to select [DATE SET], then press the knob.

10Turn the volume knob to make the settings, then press the knob.

Day Month Year or Month Day Year

11Press and hold to exit.

To return to the previous setting item, press .

3Set the initial settings

1 Press repeatedly to enter STANDBY.

2 Press the volume knob to enter [FUNCTION].

3Turn the volume knob to select an item (see the following table), then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default: XX

AUDIO CONTROL

SWITCH	(For			/		/		/
PREOUT			)

REAR/SUBWOOFER or REAR/SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the rear (through an external amplifier). ( 38)

4ENGLISH

GETTING STARTED

DISPLAY

EASY MENU (For / / /

/ ) When entering [FUNCTION]...

ON: ZONE 1 illumination changes to white color. ;

OFF: ZONE 1 illumination remains as [COLOR SELECT] color. ( 28)

•ZONE 2 illumination changes to white color when you enter [FUNCTION], irregardless of the [EASY MENU] setting.

•Refer to the illustration on page 27 for ZONE identification.

TUNER SETTING

PRESET TYPE		NORMAL: Memorizes one station for each preset button in each band
		(FM1/FM2/FM3/AM). ; MIX: Memorizes one station or SiriusXM channel
		for each preset button, regardless of the selected band or SiriusXM
		channel.
SYSTEM
KEY BEEP		ON: Activates the keypress tone. ; OFF: Deactivates.
SOURCE SELECT
	PANDORA SRC	(Except for		)
		ON: Enables PANDORA in source selection. ; OFF: Disables. (			11)
	IHEART SRC	(Except for		)
		ON: Enables IHEARTRADIO in source selection. ; OFF: Disables. ( 12)
	SPOTIFY SRC	ON: Enables SPOTIFY in source selection. ; OFF: Disables. (			13)
	BUILT-IN AUX	ON: Enables AUX in source selection. ; OFF: Disables. ( 10)
CD READ		1: Automatically distinguishes between audio file disc and music CD. ;
		2: Forces to play as a music CD. No sound can be heard if an audio file disc
		is played.

USER S.REMO (For )

See page 28 for details.

F/W UPDATE

UPDATE SYSTEM

	F/W UP xxxx	YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not
		activated).
		For details on how to update the firmware, visit
		<www.kenwood.com/cs/ce/>.
FACTORY RESET		YES: Resets the settings to default (except the stored station). ;
		NO: Cancels.
CLOCK
CLOCK DISPLAY		(Except for		)
		ON: The clock time is shown on the display even when the unit is turned
		off. ; OFF: Cancels.
ENGLISH		Select the display language for [FUNCTION] menu and music information
		if applicable.

ESPANOL	By default, [ENGLISH] is selected.

ENGLISH 5

GETTING STARTED

RADIO

Register the marine remote ID (for )

Applicable only when you connect Kenwood Marine Remote Control unit (KCA-RC55MR, optional accessory) to this unit.

•For connection, 37, Wiring connection and 38, Connecting external components.

•Refer also to the supplied instruction manual of the Kenwood Marine Remote Control unit for more information.

Preparation:

Press repeatedly to enter STANDBY, then press the volume knob to enter [FUNCTION].

1Turn the volume knob to select an item, then press the knob.

[SYSTEM] [REM SETTING] [REMOTE ID SET]

Remote control ID list is displayed.

•[YES] indicates that this ID is already registered.

•[NO] indicates that this ID is available.

2Turn the volume knob to select an available ID [REM ID1]/[REM ID2]/ [REM ID3], then press the knob.

“REGISTERING” appears on the display window.

To register, on the Kenwood Marine Remote Control unit:

•Press ENTER to register as [REM ID1].

•Press SRC to register as [REM ID2].

•Press DISP to register as [REM ID3].

Once the ID is registered, “COMPLETED” appears.

To delete the registered ID

1Turn the volume knob to select an item, then press the knob.

[SYSTEM] [REM SETTING] [REMOTE ID DEL]

2Turn the volume knob to select the ID to delete [ID1 DELETE]/ [ID2 DELETE]/[ID3 DELETE], then press the knob.

3Turn the volume knob to select [YES] to delete the selected ID, and select [NO] to cancel.

•To exit, press and hold .

•To return to the previous setting item, press .

Search for a station

1 Press repeatedly to select RADIO.

2Press repeatedly (or press / on the remote control) to select FM1/FM2/FM3/AM.

3Press S / T (or press S / on the remote control) to search for a station.

•To change the searching method for S / T: Press repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

•To store a station: Press and hold one of the number buttons (1 to 6).

•To select a stored station: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on the remote control).

Direct Access Tuning (using the remote control)

1 Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a frequency.

3Press to search for a station.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

6ENGLISH

RADIO

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/ activated or follow the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

				Default: XX
TUNER SETTING
AUTO	YES: Automatically starts memorizing 6 stations with
MEMORY	good reception. ; NO: Cancels.
	• Selectable only if [NORMAL] is selected for
	[PRESET TYPE]. (		5)
MONO SET	ON: Improves the FM reception, but the stereo effect
	may be lost. ; OFF: Cancels.
NEWS SET	(For			)
	ON: The unit will temporarily switch to News
	Programme if available. ; OFF: Cancels.
REGIONAL	(For			)
	ON: Switches to another station only in the specific
	region using the “AF” control. ; OFF: Cancels.
AF SET	(For			)
	ON: Automatically searches for another station
	broadcasting the same program in the same Radio
	Data System network with better reception when the
	current reception is poor. ; OFF: Cancels.
TI	ON: Allows the unit to temporarily switch to Traffic
	Information if available (“TI” lights up). ; OFF: Cancels.

PTY SEARCH (For / / / / /

/ )

Select the available Program Type, then press S / T to start.

(For )

1 Turn the volume knob to select the available Program Type, then press the knob.

2Turn the volume knob to select the PTY language (ENGLISH/FRENCH/GERMAN), then press the knob.

3 Press S / T to start searching.

CLOCK

TIME SYNC	ON: Synchronizes the unit’s time to the Radio Broadcast Data System/Radio Data System station
	time. ; OFF: Cancels.

Available Program Type for [PTY SEARCH]

(For / / / / /

/ )

SPEECH : NEWS, INFORM (information), SPORTS, TALK, LANGUAGE, REL TALK (religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP (spanish talk), WEATHER

MUSIC : ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40,

COUNTRY, OLDIES, SOFT, NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B

(rhythm and blues), SOFT R&B (soft rhythm and blues), REL MUSC (religious music), MUSC ESP (spanish music), HIP HOP

(For

)

SPEECH : NEWS, AFFAIRS, INFO (information), SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

MUSIC : POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music)

The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.

•[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH] is selectable only when the band is FM1/FM2/FM3.

•If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

ENGLISH 7

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

CD

M Eject disc				Label side

USB input terminal

USB

CA-U1EX (max.: 500 mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory)*1 or accessory of the iPod/iPhone*2

ANDROID*3

USB cable*2 (commercially available)

To		On the faceplate					On the remote control
Playback/pause		Press	.				Press		.
Reverse/Fast-forward*4		Press and hold S / T.					Press and hold S /			.
Select a track/file		Press S / T.					Press S /		.
Select a folder*5		Press	/ .				Press	/		.
Repeat play*6		Press	repeatedly.
		TRACK REPEAT/ALL REPEAT					: Audio CD
		FILE REPEAT/FOLDER REPEAT/ALL REPEAT					: MP3/WMA/AAC/WAV/FLAC file
		FILE REPEAT/FOLDER REPEAT/REPEAT OFF					: iPod or ANDROID
Random play*6		Press	repeatedly.
		DISC RANDOM/RANDOM OFF			: Audio CD
		FOLDER RANDOM/RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file, iPod or
					ANDROID
		Press and hold		to select ALL RANDOM.*7
*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
*3	When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
	to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
*4	before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
	For ANDROID: Applicable only when [BROWSE MODE] is selected. (				9)
*5	For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*6	For iPod/ANDROID: Applicable only when [MODE OFF]/[BROWSE MODE] is selected. (							9)
*7	For CD: Only for MP3/WMA/AAC files.

8ENGLISH

CD/USB/iPod/ANDROID

Select control mode

While in iPod USB source, press 5 repeatedly.

MODE ON: Control iPod using the iPod itself. However, you can still play/ pause, file skip, fast-forward or reverse from this unit.

MODE OFF: Control iPod from this unit.

While in ANDROID source, press 5 repeatedly.

BROWSE MODE: Control Android device from this unit via KENWOOD MUSIC PLAY application installed in the Android device.

HAND MODE: Control Android device using the Android device itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

•Selected internal or external memory of a smartphone (Mass Storage Class).

•Selected drive of a multiple drives device.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

For iPod/ANDROID, applicable only when [MODE OFF]/[BROWSE MODE] is selected.

1	Press	.
2	Turn the volume knob to select a folder/list, then press the knob.

3 Turn the volume knob to select a file, then press the knob.

Quick Search (applicable only for CD, USB and ANDROID source)

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search (applicable only for iPod USB and ANDROID source)

Press S / T to search at a preset skip search ratio. (10,

[SKIP SEARCH])

• Pressing and holding S / T searches at a 10% ratio.

Alphabet search (applicable only for iPod USB and ANDROID source)

You can search for a file according to the first character.

For iPod USB source

1 Turn the volume knob quickly to enter character search.

2Turn the volume knob to select the character.

•Select “*” to search for a character other than A to Z, 0 to 9.

3 Press S / T to move to the entry position.

•You can enter up to 3 characters.

4 Press the volume knob to start searching.

For ANDROID source

1 Press / to enter character search.

2Turn the volume knob to select the character. ^A^: Upper case letters (A to Z)

_A_: Lower case letters (a to z) -0-: Numbers (0 to 9)

***: Character other than A to Z, 0 to 9

3Press the volume knob to start searching.

•To return to the root folder/first file/top menu, press 5. (Not applicable for

BT AUDIO source.)

•To return to the previous setting item, press .

•To cancel, press and hold .

ENGLISH 9

CD/USB/iPod/ANDROID

Direct Music Search (using the remote control)

1 Press DIRECT.

2 Press the number buttons to enter a track/file number. 3 Press to search for music.

•To cancel, press or DIRECT.

•Not available if Random Play is selected.

•Not applicable for iPod USB and ANDROID source.

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth. ( 23)

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

	Default: XX
USB
MUSIC DRIVE	DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 4]) is selected
	automatically and playback starts.
	Repeat steps 1 to 3 to select the following drives.
SKIP SEARCH	0.5%/1%/5%/10%: While listening to iPod USB or ANDROID source, selects the
	skip search ratio over the total files.

AUX

Preparation:

Select [ON] for [BUILT-IN AUX] for [SOURCE SELECT]. ( 5)

Start listening

1 Connect a portable audio player (commercially available).

Auxiliary input jack

Portable audio player

3.5 mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX.

3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [SYSTEM], then press the knob.

3Turn the volume knob to select [AUX NAME SET], then press the knob.

4 Turn the volume knob to select an item, then press the knob.

AUX (default)/DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press .

10 ENGLISH

Pandora® (except for		)
Preparation:
				Create and save a new station
Install the latest version of the Pandora application on your
			1
device (iPhone/iPod touch), then create an account and log					Press	.
in to Pandora.			2		Turn the volume knob to select [NEW STATION], then press the knob.
• Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. ( 5)			3		Turn the volume knob to select [FROM ARTIST] or [FROM TRACK], then press the knob.
					A new station is created based on the artist or current song.
Start listening			4
					Press and hold one of the number buttons (1 to 5) to store.
1 Open the Pandora application on your device.				To select a stored station: Press one of the number buttons (1 to 5).
2 Connect your device to the USB input terminal.

Search for a registered station

USB input terminal

KCA-iP102/KCA-iP103 (optional accessory)*1 or accessory of the iPod/iPhone*2

3Press repeatedly to select PANDORA.

Broadcast starts automatically.

To		On the faceplate		On the remote
				control
Playback/pause		Press	.	Press	.
Skip a track		Press T.		Press	.
Thumbs up or		Press	/ .	Press
thumbs down*3				/	.
*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
*3	If thumbs down is selected, the current track is skipped.

1 Press .

2Turn the volume knob to select an item, then press the knob.

[SORT BY DATE]: According to the registered date [SORT BY A-Z]: By alphabetical order

3Turn the volume knob (or press J/ K on the remote control) to select the desired station.

4 Press the volume knob (or press on the remote control) to confirm.

To cancel, press and hold .

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

Delete a station

While listening to PANDORA...

1 Press .

2 Turn the volume knob to select [STATION DEL], then press the knob.

3 Turn the volume knob to select [SORT BY DATE] or [SORT BY A-Z], then press the knob. 4 Turn the volume knob to select the desired station to delete, then press the knob. 5 Turn the volume knob to select [YES], then press the knob.

6 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH 11

iHeartRadio® (except for )

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio.

• Select [ON] for [IHEART SRC] in [SOURCE SELECT]. ( 5)

Start listening

1 Open the iHeartAuto application on your device.

2Connect your device to the USB input terminal.

USB input terminal

KCA-iP102/KCA-iP103 (optional accessory)*1 or accessory of the iPod/iPhone*2

3Press repeatedly to select IHEARTRADIO.

Broadcast starts automatically.

*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.

To	On the faceplate		On the remote control
Playback/pause	Press	.	Press	.
Skip a track for custom	Press T.		Press	.
station
Thumbs up or thumbs	Press	/ .	( Not available )
down
Create a new/custom	Press 1.		( Not available )
station
Scan for live station	1 Press 2 to start
	scanning.
	2 Press 2 again		( Not available )
	to listen to the
	station.

Search and store a station

1 Press .

2 Turn the volume knob to select a category, then press the knob.

3Turn the volume knob (or press J/ K on the remote control) to select the desired station.

4Press the volume knob (or press on the remote control) to confirm.

When a city list appears, you can search cities in alphabetical order by turning the volume knob quickly.

To cancel, press and hold .

To store a station: Press and hold one of the number buttons (3, 4 or 5). To select a stored station: Press one of the number buttons (3, 4 or 5).

12 ENGLISH

Spotify

Preparation:

Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify.

• Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. ( 5)

Start listening

1 Open the Spotify application on your device.

2Connect your device to the USB input terminal.

USB input terminal

KCA-iP102/KCA-iP103 (optional accessory)*1 or accessory of the iPod/iPhone*2

3Press repeatedly to select SPOTIFY.

Broadcast starts automatically.

*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
To		On the faceplate		On the remote control
Playback/pause		Press	.	Press		.
Skip a track		Press S*3 / T.		Press S*3 /		.
Thumbs up or		Press	/ .	Press	/	.
thumbs down*4
Start radio		Press and hold 5.		(Not available)
Repeat play*5		Press	repeatedly.
		REPEAT ALL/REPEAT ONE*3/		(Not available)
		REPEAT OFF

To		On the faceplate		On the remote control
Random play*5		Press	repeatedly.*3	(Not available)
		SHUFFLE ON/SHUFFLE OFF
*3	Available for premium account users only.
*4	This feature is available for tracks in Radio only. If thumbs down is selected, the current
*5	track is skipped.
	Available for tracks in Playlists only.

Save favorite song information

While listening to the Radio on Spotify...

Press and hold the volume knob.

“SAVED” appears and the information is stored to “Your Music” or “Your Library” on your Spotify account.

To unsave, repeat the same procedure.

“REMOVED” appears and the information is removed from “Your Music” or “Your Library” on your Spotify account.

Search for a song or station

1 Press .

2Turn the volume knob to select a list type, then press the knob.

The list types displayed differ depending on the information sent from Spotify.

3Turn the volume knob (or press J/ K on the remote control) to select the desired song or station.

4Press the volume knob (or press on the remote control) to confirm.

You can browse through the list quickly by turning the volume knob quickly.

To cancel, press and hold .

ENGLISH 13

SiriusXM® Radio (for / / / )

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit <www.siriusxm.com>.

Preparation:

1Connect the optional SiriusXM Vehicle Tuner (commercially available).

Antenna

SiriusXM Vehicle Tuner Expansion port on

the rear panel

2Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3Activate the subscription.

For users in the U.S.A.:

Online: Go to <www.siriusxm.com> Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to <www.siriusxm.ca/activatexm> Phone: Call 1-877-438-9677

4 Press repeatedly to select SIRIUS XM to start updating.

Start listening

1 Press repeatedly to select SIRIUS XM.

2 Press repeatedly to select a band.

3Press .

“” lights up.

4Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be shown.

5Turn the volume knob to select a channel, then press the knob. (or)

Press S / T to search for a channel manually.

• Pressing and holding S / T changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 16)

To change the tuning method for S / T: Press .

Each time you press, the tuning method switches between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).

Direct Access Tuning (using the remote control)

1 Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a channel number.

3Press to start searching.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

14 ENGLISH

SiriusXM® Radio (for / / / )

SiriusXM Keymode

Press and hold to change the keymode (channel or replay). (Default: Channel keymode)

“” lights up when replay keymode is selected.

When channel keymode is selected...

To	On the faceplate		On the remote control
Select a channel	Press S / T.		Press S /	.
Change a channel	Press and hold		Press and hold
rapidly	S / T.		S /	.
Store a channel of	Press and hold one of
the current band	the number buttons		(Not available)
	(1 to 6).
Select a stored	Press one of the number buttons (1 to 6).
channel of the
current band
When replay keymode is selected...
To	On the faceplate		On the remote control
Playback/pause	Press	.	Press	.
Skip backward/	Press S / T.		Press S /	.
forward
Rewind/	Press and hold		Press and hold
Fast-forward	S / T.		S /	.
Go to Live	Press 1.

SmartFavorites and TuneStart™

User stored channels are recognized as SmartFavorite channels*. The SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.

•SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle Tuner.

*SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites. The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as SmartFavorites.

When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.

•Playback starts from the beginning of the song if [TUNE START] is set to [ON] ( 16) for most music channels stored as a SmartFavorite.

Press one of the number buttons (1 to 6) to select a stored channel.

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.

Press and hold to start scanning the first 6 seconds of the recorded music contents.

•To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.

•To select the previous/next song, press S / T.

•To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.

ENGLISH 15

SiriusXM® Radio (for / / / )

SiriusXM settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.

4 Press and hold

to exit.

To return to the previous setting item, press .

Default: XX

SIRIUS XM

CHANNEL LOCK		To unlock settings:
		1	Turn the volume knob to select a number.
		2	Press S / T to move to the entry position.
		3	Repeat steps 1 and 2 to enter the current pass code.
		4	(Initial pass code is 0000.)
			Press the volume knob to confirm.
	CODE SET	1 Turn the volume knob to select a number.
		2	Press S / T to move to the entry position.
		3	Repeat steps 1 and 2 to enter a new 4-digit pass code.
		4	Press the volume knob to confirm.
		5	Repeat steps 1 to 4 to reconfirm the pass code.
		• Make a note of the new pass code to enter channel lock settings for next time.
	LOCK SETTING	MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects
		the individual channels the user wants to lock. ; OFF: Cancels.
	CHANNEL EDIT*1	1 Turn the volume knob to select a category, then press the knob.

2Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number.

3 Press and hold to exit.

CHANNEL CLEAR*1 YES: Clears all the locked channels. ; NO: Cancels.

TUNE START*2	ON: All qualified music channels in the SmartFavorite
	will start playback from the beginning of the song. ;
	OFF: Cancels.
SIGNAL LEVEL	Shows the strength (NO SIGNAL/WEAK/GOOD/
	STRONG) of the current received signal.
BUFFER USAGE	Shows the memory usage (0% to 100%) for Replay
	buffer.
SXM RESET	YES: Resets stored channel and lock setting to
	default. ; NO: Cancels.

*1	Displayed only when [USER DEFINED] is selected.
*2	Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that
	supports SmartFavorites.

16 ENGLISH

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

–Hands-Free Profile (HFP)

–Advanced Audio Distribution Profile (A2DP)

–Audio/Video Remote Control Profile (AVRCP)

–Serial Port Profile (SPP)

–Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

–Sub Band Codec (SBC)

–Advanced Audio Coding (AAC)

Connect the microphone

MIC (microphone input terminal)*

Microphone (supplied)

Rear panel

Adjust the microphone angle Secure using cord clamps

(not supplied) if necessary.

* / / / : Connect to the microphone input jack. ( 38)

Pair and connect a Bluetooth device for the first time

1 Press to turn on the unit.

2Search and select this unit model name (KDC-X3**/KDC-BT3**/KDC-BT3*/ KDC-BT2*/KDC-MP3**/KMR-D3**) on the Bluetooth device.

“PAIRING” “PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” appears on the display.

•For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.

3Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

Once pairing is completed, Bluetooth connection is established automatically.

• / / / / : “BT1” and/or “BT2” indicator on the faceplate lights up.

• / / : “BT1” and/or “BT2” on the display window lights up.

•This unit supports Secure Simple Pairing (SSP).

•Up to five devices can be registered (paired) in total.

•Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 21, [DEVICE DELETE].

•A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. ( 22)

•Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

•Refer to the instruction manual of the Bluetooth device for more information.

ENGLISH 17

BLUETOOTH®

Auto Pairing	BLUETOOTH — Mobile phone

When you connect iPhone/iPod touch/Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if:

–Bluetooth function of the connected device is turned on.

–[AUTO PAIRING] is set to [ON]. ( 21)

–KENWOOD MUSIC PLAY application is installed on the Android device ( 8) and [BROWSE MODE] is selected

( 9).

Receive a call

When there is an incoming call:

• / / / / : ZONE 2 illuminates in green color and flashes.

•The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 19)

During a call:

• / / / / : ZONE 1 illuminates according to the settings made for [DISPLAY] ( 28) and ZONE 2 illuminates in green color.

•If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

	To	On the faceplate		On the remote control
First incoming call...
	Answer a call	Press	or the volume knob	Press .
		or one of the number buttons
		(1 to 6).
	Reject a call	Press	.	Press	.
	End a call	Press	.	Press	.

18 ENGLISH

BLUETOOTH®

To

On the faceplate

On the remote control

While talking on the first incoming call...

	Answer another incoming	Press .		Press .
	call and hold the current
	call
	Reject another incoming	Press	.	Press	.
	call
While having two active calls...
	End current call and	Press	.	Press	.
	activate held call
	Swap between the	Press .		Press .
	current call and held call
Adjust the phone volume		Turn the volume knob		Press	or
[00] to [35] (Default: [15])		during a call.			.

•This adjustment will not affect the volume of the other sources.

Switch between hands-free	Press	during a call.
and private talk modes	• Operations may vary		( Not available )
	according to the connected

Bluetooth device.

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

	Default: XX
MIC GAIN	–10 to +10 (–4): The sensitivity of the microphone
	increases as the number increased.
NR LEVEL	–5 to +5 (0): Adjust the noise reduction level until the
	least noise is being heard during a phone conversation.
ECHO CANCEL	–5 to +5 (0): Adjust the echo cancellation delay time
	until the least echo is being heard during a phone
	conversation.

Make the settings for receiving a call 1 Press to enter Bluetooth mode.

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

										Default: XX
SETTINGS
AUTO ANSWER	1 to 30: The unit answers incoming call automatically in
	the selected time (in seconds). ; OFF: Cancels.
BATT/SIGNAL*	(For			/						/
					/			/			)
	AUTO: Shows the strength of the battery and signal

when the unit detects a Bluetooth device and the Bluetooth device is connected. ; OFF: Cancels. Clock time is shown.

* Functionality depends on the type of the phone used.

ENGLISH 19

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1Press to enter Bluetooth mode.

“(First device name)” appears.

•If two Bluetooth phones are connected, press again to switch to another phone.

“(Second device name)” appears.

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY (Applicable only if the phone supports PBAP.)

1Press the volume knob to select a name or a phone number.

• / / /

/ : “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

/ / : “I” indicates call received, “O” indicates call made, “M” indicates call missed.

•Press DISP to change the display category (NUMBER or NAME).

•“NO DATA” appears if there is no recorded call history.

2 Press the volume knob to call.

PHONE BOOK (Applicable only if the phone supports PBAP.)

1Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

•To go to the other menu (LMNOPQRSTUV or WXYZ1*), press/.

•To select the desired first letter, turn the volume knob or press S / T, then press the knob.

Select “1” to search with numbers and select “*” to search with symbols. 2 Turn the volume knob to select a name, then press the knob.

3 Turn the volume knob to select a phone number, then press the knob to call.

•The phonebook of the connected phone is automatically transferred to the unit when pairing.

•Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL or HM (home), OF (office), MO (mobile), OT (other), GE (general)

•This unit can display only non-accent letters. (Accent letters such as “Ú” is shown as “U”.)

NUMBER DIAL

1 Turn the volume knob to select a number (0 to 9) or character ( , #, +).

2Press S / T to move the entry position.

Repeat steps 1 and 2 until you finish entering the phone number.

3 Press the volume knob to call.

		(or using the remote control)
	1	Press the number buttons (0 to 9) to enter the phone number.
	2	Press	to call.
VOICE	Speak the name of the contact you want to call or the voice command to control
	the phone functions. ( 21, Make a call using voice recognition)

BATT LOW/MID/FULL*: Shows the strength of the battery.

NO SIGNAL/LOW/MID/MAX*: Shows the strength of the current received signal.

* Functionality depends on the type of the phone used.

20 ENGLISH

BLUETOOTH®

Make a call using voice recognition

1Press and hold to activate the voice recognition of the connected phone.

2Speak the name of the contact you want to call or the voice command to control the phone functions.

•Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

•This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode.

2Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob.

3Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone number.

4Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored.

To erase a contact from the preset memory, select [NUMBER DIAL] in step 2 and store a blank number.

Make a call from memory

1 Press to enter Bluetooth mode.

2 Press one of the number buttons (1 to 6).

3Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.

4 Press and hold

to exit.

To return to the previous setting item, press .

Default: XX

BT MODE

PHONE SELECT

AUDIO SELECT

Selects the phone or audio device to connect or disconnect. “*” appears in front of the device name when connected. “” appears in front of the current playback audio device.

•You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.

DEVICE DELETE	1	Turn the volume knob to select a device to delete, then press the knob.
	2	Turn the volume knob to select [YES] or [NO], then press the knob.
PIN CODE EDIT	Changes the PIN code (up to 6 digits).
(0000)	1	Turn the volume knob to select a number.
	2	Press S / T to move the entry position.
	3	Repeat steps 1 and 2 until you finish entering the PIN code.
		Press the volume knob to confirm.
RECONNECT	ON: The unit automatically reconnect when the last connected Bluetooth device
	is within range. ; OFF: Cancels.
AUTO PAIRING	ON: The unit automatically pair supported Bluetooth device (iPhone/iPod touch/
	Android device) when it is connected through USB input terminal. Depending
	on the operating system of the connected device, this function may not work. ;
	OFF: Cancels.
INITIALIZE	YES: Initializes all the Bluetooth settings (including stored pairing, phonebook,
	and etc.). ; NO: Cancels.

ENGLISH 21

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2Search and select this unit model name (KDC-X3**/KDC-BT3**/KDC-BT3*/KDC-BT2*/ KDC-MP3**/KMR-D3**) on the Bluetooth device.

3Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING:	Pairing status
HF CNT:	Hands-Free Profile (HFP) compatibility
AUD CNT: Advanced Audio Distribution Profile
	(A2DP) compatibility
PB DL:	Phonebook Access profile (PBAP)
	compatibility
To cancel test mode, press and hold		to turn
off the unit.

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

1 Press repeatedly (or press SRC on the remote control) to select BT AUDIO. 2 Operate the Bluetooth audio player to start playback.

To	On the faceplate			On the remote control
Playback/pause	Press	.		Press	.
Select group or folder	Press	/ .		Press	/	.
Reverse/Forward skip	Press S / T.			Press S /	.
Reverse/Fast-forward	Press and hold S / T.			Press and hold S /		.
Repeat play	Press	repeatedly.		( Not available )
	ALL REPEAT, FILE REPEAT, REPEAT OFF
Random play	Press and hold		to select
	ALL RANDOM.			( Not available )
	• Press	to select RANDOM OFF.
Select a file from a	Refer to “Select a file from a folder/			( Not available )
folder/list	list” on page 9.
Switch between	Press 5.*
connected Bluetooth				( Not available )
audio device

* Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.

Operations and display indications may differ according to their availability on the connected device.

22 ENGLISH

BLUETOOTH®

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
REMOTE APP
SELECT		Select the device (IOS or ANDROID) to use the application.
	IOS	YES: Selects iPhone/iPod to use the application via Bluetooth or connected
		via USB input terminal. ; NO: Cancels.
		If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is
		connected via USB input terminal) to activate the application.
		• The connectivity of the application will be interrupted or disconnected
		if:
		– You change from iPod BT source to any playback source connected via
		the USB input terminal.
		– You change from iPod USB source to iPod BT source.

ANDROID YES: Selects Android smartphone to use the application via Bluetooth. ; NO: Cancels.

ANDROID LIST*: Selects the Android smartphone to use from the list.

* Displayed only when [ANDROID] of [SELECT] is set to [YES].

STATUS Shows the status of the selected device.

IOS CONNECTED: You are able to use the application using the iPhone/iPod connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED: No IOS device is connected to use the application. ANDROID CONNECTED: You are able to use the application using the Android smartphone connected via Bluetooth.

ANDROID NOT CONNECTED: No Android device is connected to use the application.

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press repeatedly to select iPod BT.

•You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal ( 8).

•If you plug in an iPhone/iPod to the USB input terminal while listening to iPod BT source, the source automatically change to iPod USB. Press to select iPod BT if the device is still connected via Bluetooth.

Internet radio via Bluetooth

You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the iPhone/iPod/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Listen to Pandora (except for )

Preparation:

Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. ( 5)

1 Open the Pandora application on your device.

2 Connect your device via Bluetooth connection. ( 17)

3Press repeatedly to select PANDORA (for iPhone/iPod) or PANDORA BT (for Android device).

The source switches and broadcast starts automatically.

•You can operate Pandora in the same way as Pandora via USB input terminal. ( 11)

ENGLISH 23

BLUETOOTH®

Listen to iHeartRadio (except for )

Preparation:

Select [ON] for [IHEART SRC] in [SOURCE SELECT]. ( 5)

1 Open the iHeartAuto application on your device.

2 Connect your device via Bluetooth connection. ( 17)

3Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically.

•You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal. ( 12)

Listen to Spotify

Preparation:

Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. ( 5)

1 Open the Spotify application on your device.

2 Connect your device via Bluetooth connection. ( 17)

3Press repeatedly to select SPOTIFY (for iPhone/iPod) or SPOTIFY BT (for Android device).

The source switches and broadcast starts automatically.

•You can operate Spotify in the same way as Spotify via USB input terminal. ( 13)

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

(or using the remote control)

1 Press AUD to enter [AUDIO CONTROL].

2 Press J/ K to select an item, then press .

To return to the previous setting item, press .

			Default: XX
AUDIO CONTROL
SUB-W LEVEL		LEVEL –50 to LEVEL +10 (LEVEL 0): Adjusts the subwoofer output
		level.
MANUAL EQ		The sound elements (frequency level, tone level, Q factor) are preset
		into each selection.
	62.5HZ	LEVEL	LEVEL–9 to LEVEL +9 (LEVEL 0): Adjusts the
			level to memorize for each source.
			(Before making an adjustment, select the source
			you want to adjust.)
		BASS EXTEND	ON: Turns on the extended bass. ; OFF: Cancels.
	100HZ/160HZ/250HZ/	LEVEL–9 to LEVEL +9 (LEVEL 0): Adjusts the level to memorize for
	400HZ/630HZ/1KHZ/	each source. (Before making an adjustment, select the source you
	1.6KHZ/2.5KHZ/4KHZ/	want to adjust.)
	6.3KHZ/10KHZ/16KHZ
	Q FACTOR	1.35/1.50/2.00: Adjust the quality factor.
PRESET EQ		NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL/USER:
		Selects a preset equalizer suitable to the music genre. (Select [USER]
		to use the settings made in [MANUAL EQ].)

24 ENGLISH

AUDIO SETTINGS

BASS BOOST		LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5 or LV1/LV2/LV3/
		LV4/LV5: Selects your preferred bass boost level. ; OFF: Cancels.
LOUDNESS		LEVEL1/LEVEL2 or LV1/LV2: Selects your preferred low and
		high frequencies boost to produce a well-balanced sound at a
		low volume level. ; OFF: Cancels.
SUBWOOFER SET		ON: Turns on the subwoofer output. ; OFF: Cancels.
FADER		R15 to F15 (0): Adjusts the rear and front speaker output
		balance.
BALANCE		L15 to R15 (0): Adjusts the left and right speaker output
		balance.
VOLUME OFFSET		–15 to +6 (0): Preset the initial volume level of each source.
		(Before adjustment, select the source you want to adjust.)
SOUND EFFECT
	SOUND RECNSTR	(Not applicable for RADIO source, AUX source and SIRIUS XM
	(Sound	source.)
	reconstruction)	ON: Creates realistic sound by compensating the high-frequency
		components and restoring the rise-time of the waveform that
		are lost in audio data compression. ; OFF: Cancels.
	SPACE ENHANCE	(Not applicable for RADIO source.)
		SMALL/MEDIUM/LARGE or SML/MED/LRG: Virtually enhances
		the sound space. ; OFF: Cancels.
	SND REALIZER	LEVEL1/LEVEL2/LEVEL3 or LV1/LV2/LV3: Virtually makes the
		sound more realistic. ; OFF: Cancels.
	STAGE EQ	LOW/MIDDLE/HIGH or LOW/MID/HI: Virtually adjust the
		sound position heard from the speakers. ; OFF: Cancels.
	DRIVE EQ	ON: Boosts the frequency to reduce the noise heard from
		outside the car or running noise of the tyres. ; OFF: Cancels.

SPEAKER SIZE		The frequency and slope settings are automatically set for the crossover of the
		selected speaker.
	FRONT	SIZE	3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/
			7×10: Selects according to the connected speaker size for
			optimum performance.
		TWEETER	SMALL/MIDDLE/LARGE: Selects according to the size
			range of the connected tweeter for optimum performance. ;
			NONE: Not connected.
	REAR	3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10: Selects
		according to the connected speaker size for optimum performance. ;
		NONE: Not connected.
	SUBWOOFER	6.5"/8"/10"/12"/15" OVER: Selects according to the connected speaker size
		for optimum performance. ; NONE: Not connected.
X ' OVER
	TWEETER	FRQ	1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/
			10KHZ/12.5KHZ: Adjusts the crossover frequency for the
			tweeter speaker.
		GAIN LEFT	–8 to 0: Adjusts the output volume of the left tweeter.
		GAIN RIGHT	–8 to 0: Adjusts the output volume of the right tweeter.
	FRONT HPF	F - HPF FRQ	30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/
			120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts the
			crossover frequency for the selected speakers (high pass
			filter). ; THROUGH: All signals are sent to the selected
			speakers.
		F - HPF SLOPE	–6DB/–12DB/–18DB/–24DB: Adjusts the crossover slope.
			(Selectable only if a setting other than [THROUGH] is selected
			for [F - HPF FRQ].)
		F - HPF GAIN	–8 to 0: Adjusts the output volume of the selected speaker.

ENGLISH 25

AUDIO SETTINGS

		REAR HPF	R - HPF FRQ
				(Refer FRONT HPF settings on page 25.)
			R - HPF SLOPE
			R - HPF GAIN
		SUBWOOFER	SW LPF FRQ	30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/
		LPF		100HZ/120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts
				the crossover frequency for the subwoofer (low pass
				filter). ; THROUGH: All signals are sent to the subwoofer.
			SW LPF SLOPE	–6DB/–12DB/–18DB/–24DB: Adjusts the crossover
				slope. (Selectable only if a setting other than [THROUGH]
				is selected for [SW LPF FRQ].)
			SW LPF PHASE	REVERSE (180°)/NORMAL (0°): Selects the phase of the
				subwoofer output to be in line with the speaker output
				for optimum performance.
			SW LPF GAIN	–8 to 0: Adjusts the output volume of the subwoofer.
	DTA SETTINGS		For settings, Digital Time Alignment settings.
	CAR SETTINGS

•(For / / / ) The following item is selectable only if [SWITCH PREOUT] is set to [SUBWOOFER] or

[SUB-W] ( 4):

–[SUB-W LEVEL], [SUBWOOFER SET]

–[SUBWOOFER] of [SPEAKER SIZE]

–[SUBWOOFER LPF] of [X ‘ OVER]

–[SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]

•The following item is selectable only if [SUBWOOFER SET] is set to [ON] ( 25):

–[SUB-W LEVEL]

–[SUBWOOFER] of [SPEAKER SIZE]

–[SUBWOOFER LPF] of [X ‘ OVER]

–[SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]

•The following item is selectable only if a setting other than [NONE] is selected for

[TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE]:

–[TWEETER], [REAR HPF], [SUBWOOFER LPF] of [X ‘ OVER]

Digital Time Alignment settings

Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.

•For more information, 27, Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS].

DTA SETTINGS

	POSITION	Selects your listening position (reference point).
		ALL: Not compensating ; FRONT RIGHT: Front right seat ;
		FRONT LEFT: Front left seat ; FRONT ALL: Front seat
	DISTANCE	0FT to 20.01FT: Fine adjust the distance to compensate. (Before
		making an adjustment, select the speaker you want to adjust.)
	GAIN	–8DB to 0DB: Fine adjust the output volume of the selected speaker.
		(Before making an adjustment, select the speaker you want to adjust.)
	DTA RESET	YES: Resets the settings ([DISTANCE] and [GAIN]) of the selected
		[POSITION] to default. ; NO: Cancels.
CAR SETTINGS		Identify your car type and rear speaker location in order to make the
		adjustment for [DTA SETTINGS].
	CAR TYPE	COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV/
		MINIVAN(LONG): Selects the type of vehicle. ; OFF: Not
		compensating.

R-SP LOCATION Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point).

•DOOR/REAR DECK: Selectable only when [CAR TYPE] is selected as

[OFF], [COMPACT], [FULL SIZE CAR], [WAGON] or [SUV].

•2ND ROW/3RD ROW: Selectable only when [CAR TYPE] is selected as [MINIVAN] or [MINIVAN(LONG)].

26 ENGLISH