Kenwood DDX8032BT, DDX812, DNX8120 Installation Manual

4 (1)

DNX8120

DDX812

DDX8032BT

GPS NAVIGATION SYSTEM MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

SYSTÈME DE NAVIGATION GPS MONITEUR AVEC RÉCEPTEUR DVD

MANUEL D’INSTALLATION

SISTEMA DE NAVEGACIÓN GPS

MONITOR CON RECEPTOR DVD

MANUAL DE INSTALACIÓN

© B54-4648-00/00 (KW/RW)

Kenwood DDX8032BT, DDX812, DNX8120 Installation Manual

Accessories

1

2

3

4

5

6

7

8

9

 

0

 

..........1

..........

6

 

!

 

..........1

..........

1

 

@

 

..........1

DNX8120 only ..........

1

 

#

 

1

DNX8120 only

1

..........

 

$

 

..........1

..........

1

 

%

 

..........2

DNX8120 only..........

1

..........1

..........1

..........6

2 | DNX8120/DDX812/DDX8032BT

Installation Procedure

1.To prevent a short circuit, remove the key from the ignition and disconnect the - battery.

2.Make the proper input and output wire connections for each unit.

3.Connect the speaker wires of the wiring harness.

4.Connect the wiring harness wires in the following order: ground, battery, ignition.

5.Connect the wiring harness connector to the unit.

6.Install the unit in your car.

7.Reconnect the - battery.

8.Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.

Acquiring GPS Signals

The first time you turn on the DNX8120, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter.

¤

Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.

Make sure to ground the unit to a negative 12V DC power supply.

Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.

If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.

If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.

Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.

When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.

After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle is 30° or less.

This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.

Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result.

Reception may drop if there are metal objects near the Bluetooth antenna.

Bluetooth antenna unit

English | 3

Connection

Ignition key switch

ACC

Car fuse box

Car fuse box (Main fuse)

C

Battery

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

A

B

A

Ignition wire (Red)

 

 

 

 

B

Battery wire (Yellow)

 

 

Ground wire (Black) -

Antenna Cord

 

 

 

 

 

 

C

(To car chassis)

 

 

 

 

Connect to the vehicle's parking brake detection switch harness.

Parking sensor wire (Light Green)

PRK SW

For the sake of safety, be sure to connect the parking sensor.

 

Reveres sensor wire (Purple/White)

Connect to vehicle's reverse lamp harness when using the optional rear view camera.

FM/AM antenna input

Steering remote control input (Light Blue/Yellow) To steering remote

To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on.

To car light control switch

Connect to the terminal that is grounded when either the telephone rings or during conversation.

To connect the Kenwood navigation system, consult your navigation manual.

Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.

When using the optional power amplifier, connect to its power control terminal.

To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function.

Dimmer control wire (Orange/White)

Mute wire (Brown)

Motor antenna control wire (Blue)

Power control wire (Blue/White)

External amplifier control wire (Pink/Black)

If no connections are made, do not let the cable come out from the tab.

4 | DNX8120/DDX812/DDX8032BT

REVERSE

REMO.CONT

ILLUMI

MUTE

ANT. CONT

P CONT

EXT.CONT

Bluetooth Microphone (Accessory $) (see page 8)

Cooling fan

GPS Antenna (Accessory @) (DNX8120 only) (see page 8)

FUSE ( 15A )

Accessory 1

 

White/Black

White

Gray/Black

Gray

Green/Black

Green

Purple/Black

Purple

+

To front left speaker

 

+

To front right speaker

 

+

To rear left speaker

 

+

To rear right speaker

 

English | 5

System Connection

USB terminal (iPod)

USB device (commercially available)

USB terminal

USB device (commercially available)

iPod

 

 

Visual input (iPod)

 

 

 

 

 

 

Resistance-free mini plug (3.5φ)

 

 

 

Audio input (iPod)

 

 

 

Resistance-free stereo type mini plug (3.5φ)

 

 

 

To XM Tuner GXM30 or TMC Tuner GTM10

 

 

 

(optional accessory) (DNX8120 only)

 

 

 

Accessory %

 

 

 

When connecting the XM Tuner GXM30

 

 

 

(optional accessory) or TMC Tuner GTM10

 

 

 

(optional accessory), put the cable clamper

Accessory

Accessory

Accessory 4

(accessory %) to the back of this unit first,

and then wire the cable through the clamper.

2

3

 

 

 

 

AV OUT

Audio/Visual Output

 

 

• Visual output (Yellow)

 

 

 

• Audio left output (White)

 

 

 

• Audio right output (Red)

 

 

IN1

Audio/Visual input1

 

 

AV

• Visual input (Yellow)

 

 

 

• Audio left input (White)

 

 

• Audio right input (Red)

IN2

Audio/Visual input2

AV

• Visual input (Yellow)

 

 

REARVIEW

CAMERA

• Audio left input (White)

• Audio right input (Red)

 

 

 

 

Rear View Camera Input

FRONT

• Visual input (Yellow)

Front Preout

 

 

 

 

• Audio left output (White)

REAR

• Audio right output (Red)

Rear Preout

SUB

WOOFER

• Audio left output (White)

• Audio right output (Red)

 

 

 

 

Subwoofer Preout

 

CENTER

• Audio left output (White)

 

• Audio right output (Red)

 

 

 

1

Center Preout

 

• Audio output (Black)

RELAY 2

RELAY

To Relay Box

6 | DNX8120/DDX812/DDX8032BT

Optional Accessory Connection

iPod

(commercially available)

Audio Output (Black) Audio Input

KCA-iP300V (Optional Accessory)

Accessory 5

Visual Output (Yellow)

Visual Input

Navigation System Input (DDX812/DDX8032BT only)

USB terminal

iPod cannot be connected.

USB terminal (iPod)

iPod

USB terminal

To SIRIUS Satellite Radio tuner/

XM Satellite Radio tuner/ HD Radio tuner (Optional Accessory)

Conversion adapter (optional accessory) may be necessary for connection of optional accessory.

Contact your Kenwood dealer for details.

TV Tuner

(Optional Accessory)

Navigation System

(Optional Accessory)

TVANTENNAINPUT

TOMONITORUNIT

Connection cable

Connection cable (Included in the Navigation System) (Included in the TV tuner)

English | 7

Installing the GPS Antenna (DNX8120 only)

GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals.

To mount the GPS antenna inside your vehicle:

1.Clean your dashboard or other surface.

2.Peel the backing off of the adhesive on the bottom of the metal plate (accessory #).

3.Press the metal plate (accessory #) down firmly on your dashboard or other mounting surface. You can bend the metal plate (accessory #) to conform to a curved surface, if necessary.

4.Place the GPS antenna (accessory @) on top of the metal plate (accessory #).

Accessory @

Accessory #

¤

Depending on the type of car, reception of the GPS satellite signals might not be possible with an inside installation.

The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with by these types of communication.

Painting the GPS antenna with (metallic) paint may cause a drop in performance.

Installing the Microphone Unit

1.Check the installation position of the microphone (accessory $).

2.Remove oil and other dirt from the installation surface.

3.Install the microphone.

4.Wire the microphone cable up to the hands-free box with it secured at several positions using tape or the like.

Accessory $

Fix a cable with a commercial item of tape.

Peel the release coated paper of double-face adhesive tape to fix on the place shown above.

Adjust the direction of the microphone to the driver.

Install the microphone as far as possible from the cell-phone.

8 | DNX8120/DDX812/DDX8032BT

Installing the Escutcheon

For General Motors

1.Cut out accessory 7 to meet the shape of the opening of the center console.

2.Attach accessory 7 to the unit.

Cut out to meet the shape of the opening in the vehicle.

Accessory 7

For Volkswagen

1. Attach accessory ! to the unit.

Accessory !

For Toyota/Scion

1. Cut out accessory 7 as illustrated.

Cutting line

Accessory 7

2.Fold double-sided adhesive (accessory 8) along the slit and attach it to accessory 7 cut-out against the center rib as illustrated. Use 2 pieces of accessory 8 for 1 accessory 7 cut-out.

3.Attach accessory 7 cut-out to the unit.

Accessory 8

English | 9

Installation for Monitor/Player Unit

Firewall or metal support

Screw (M4X8) (commercially available)

Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.

Self-tapping screw

Metal mounting strap

(commercially available)

(commercially available)

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).

Installation on Toyota, Nissan or Mitsubishi Car using Brackets

Accessory 9 (M5x6mm)

or Accessory 0 (M5x7mm)

Car Bracket

Accessory 9 (M5x6mm) or Accessory 0 (M5x7mm)

10 | DNX8120/DDX812/DDX8032BT

Loading...
+ 22 hidden pages