Kenmore Elite 79048813810, 79048973810, 79048977810, 79048823810, 79048827810 Installation Guide

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(27" and 30" Ovens with Optional Electric or Gas Cooktop Combination)

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

United States

and Canada

Your new wall oven has been designed to fit a variety of cutout sizes to make the job of installing easier. The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions chart below for your model. You may find little or no cabinet work necessary.

Do not remove spacers (if equipped) on the side walls of the built-in oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

NOTES:

1.Base must be capable of supporting 200 pounds (90 kg).

2.Allow at least 21" (53.3 cm) clearance in front of oven for door depth when it is open.

	3. Dimension G (cutout depth) is critical to			C
	the proper installation of the built-in oven.
	If the oven decorative trim does not butt
	against the cabinet, or if noise is heard		B
	on convection models, verify dimension
	G to assure it is the required depth.
	4. For a cutout height greater than 28"
	(71.1 cm) add one 2"(5 cm)
	wide wood shim of appropriate	Door Open
	height to each side of the			D
		(see note 2)
	opening under the appliance
	side rails.			A

*Suggested distance from floor is 31" (78.7cm).

Minimum required distance is 4 ½" (11.4cm).

I

1½” (3.8 cm) Min.

	G	Hole for
H	F	Cord
E		3”
		(7.6 cm)

31”* (78.7 cm)

Spacer

2” (5.1 cm)

Min. Electrical 2" (5 cm) Wide Wood Junction Box

Spacer if Needed

Figure 1

Single Wall Ovens (Double Ovens see Figure 2)

PRODUCT DIMENSIONS

MODEL

A

B

C

D

E

27" (68.6 cm) Wall Oven

27 (68.6)

29 (73.7)

245/8 (62.5)

243/4 (62.9)

2611/16 (67.8)

30" (76.2 cm) Wall Oven

30 (76.2)

29 (73.7)

281/4 (71.8)

243/4 (62.9)

267/8 (68.3)

CUTOUT DIMENSIONS AND CABINET WIDTH

F

G (Min.)

H. Standard Height

I

(**Others, see notes 4 & 5)

MODEL

Min.

Max.

Min.

Max.

27" (68.6 cm) Wall Oven

247/8 (63.2)

25¼ (64.1)

24 (61.0)

27¼ (69.2)

281/4 (71.8)

271/8 (68.9) Min

30" (76.2 cm) Wall Oven

281/2 (72.4)

29 (73.7)

24 (61.0)

27 (68.6)

283/16 (71.6)

301/8 (76.5) Min

PN 807153705 Rev. A (18/09)

All dimensions are in inches (cm).

English – pages 1-8

Printed in U.S.A.

Spanish -pages 9-16

1

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(27" and 30" Ovens with Optional Electric or Gas Cooktop Combination)

Do not remove spacers (if equipped) on the side walls of the built-in oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

			I
			1½” (3.8 cm)
			Min.
			C
			F	G
	B		H	Hole for
			E	Cable
			11½”		3” (7.6 cm)
Door Open			(29.2 cm)		Max.
			Spacer	2”
(see note 2)					Electrical
				(5.1 cm)
			D
				Min.	Junction Box
			2" (5 cm) Wide Wood
		A
			Spacer if Needed

NOTES:

1.Base must be capable of supporting 375 pounds (170 kg).

2.Allow at least 21" (53.3 cm) clearance in front of oven for door depth when it is open.

3.Dimension G (cutout depth) is critical to the proper installation of the built-in oven. If the oven decorative trim does not butt against the cabinet, or if noise is heard on convection models, verify dimension G to assure it is according to the required dimension.

4.For a cutout height greater than 49 3/4" (126.4 cm) add a 2" (5 cm) wide wood shim of appropriate height to each side of the opening under the appliance side rails.

Figure 2

27" and 30" DOUBLE OVENS (Single Ovens see Figure 1)

PRODUCT DIMENSIONS

MODEL

A

B

C

D

E

27" (68.6 cm) Wall Oven

27 (68.6)

507/16 (128.1)

245/8

(62.5)

243/4

(62.9)

487/16 (123)

30" (76.2 cm) Wall Oven

30 (76.2)

507/16 (128.1)

281/4

(71.8)

243/4

(62.9)

485/8 (123.5)

CUTOUT DIMENSIONS AND CABINET WIDTH

F

G (Min.)

H. Standard Height

I

(**Others, see notes 4 & 5)

MODEL

Min.

Max.

Min.

Max.

27" (68.6 cm) Wall Oven

247/8

(63.2)

251/4 (64.1)

24 (61.0)

487/8

(124.1)

495/8 (126)

271/8 (68.9) Min

30" (76.2 cm) Wall Oven

281/2

(72.4)

29 (73.7)

24 (61.0)

483/4

(123.8)

50 (127)

301/8 (76.5) Min

All dimensions are in inches (cm).

2

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(27" and 30" Ovens with Optional Electric or Gas Cooktop Combination)

Important Notes to the Installer

1.Read all instructions contained in these installation instructions before installing the wall oven.

2.Remove all packing material from the oven compartments before connecting the electrical supply to the wall oven.

3.Observe all governing codes and ordinances.

4.Be sure to leave these instructions with the consumer.

5.Oven door may be removed to facilitate installation.

6.THESE OVENS ARE NOT APPROVED FOR STACKABLE OR SIDE-BY-SIDE INSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for the local electrical inspector's use and future reference.

IMPORTANT SAFETY

INSTRUCTIONS

•Be sure your wall oven is installed and grounded properly by a qualified installer or service technician.

•This wall oven must be electrically grounded in accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No.70latest edition in United Sates, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in Canada.

Stepping, leaning or sitting on the door of this wall oven can result in serious injuries and can also cause damage to the wall oven.

•Never use your wall oven for warming or heating the room. Prolonged use of the wall oven without adequate ventilation can be dangerous.

The electrical power to the oven must be shut off while line connections are being made. Failure to do so could result in serious injury or death.

1. Carpentry

Refer to figure 1 or 2 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or similar material, however the surface must be level from side to side and from front to rear.

2. Adjusting Oven Height

Oven height can be adjusted with 2" (5cm) wide wood shims when needed to fit into an existing cabinet cutout opening, when cutout height exceeds 28" (71.1 cm) for the single wall oven or 493/4" (126.4 cm) for the double wall oven (see Figure 1 or 2). Place shims of appropriate height beneath the oven side rails.

3. Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. To know the circuit breaker or fuse required by your model, see the serial plate to find the wattage consumption and refer to table A to get the circuit breaker or fuse amperage.

Appliance	Protection	Appliance	Protection
Rating Watts	Circuit	Rating Watts	Circuit
240V	Recommended	208V	Recommended
Less than	20A	Less than	20A
4800W		4100W
4801W - 7200W	30A	4101W - 6200W	30A
7201W - 9600W	40A or 50A	6201W - 8300W	40A or 50A
9601W and +	50A	8301W and +	50A

Table A

Observe all governing codes and local ordinances 1.A 3-wire or 4-wire single phase 120/240 or 120/208

Volt, 60 Hz AC only electrical supply is required on a separate circuit fused on both sides of the line (red and black wires). A time-delay fuse or circuit breaker is recommended. DO NOT fuse neutral (white wire). Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number (see the insert sheet included in the literature package).

NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance with the American National Electrical Code ANSI/NFPA No. 70-latest edition, or with Canadian CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

An extension cord should not be used with this appliance. Such use may result in a fire, electrical shock, or other personal injury. If you need a longer power cord you can purchase a 10' (3 m) power cord kit #903056-9010 by calling the Service Center.

2.These appliances should be connected to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed cable. The flexible armored cable extending from the appliance should be connected directly to the junction box. The junction box should be located as shown in Figure 1 or Figure 2 and with as much slack as possible remaining in the cable between the box and the appliance, so it can be moved if servicing is ever necessary.

3.A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

3

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(27" and 30" Ovens with Optional Electric or Gas Cooktop Combination)

Electrical Shock Hazard

•Electrical ground is required on this appliance.

•Do not connect to the electrical supply until appliance is permanently grounded.

•Disconnect power to the junction box before making the electrical connection.

•This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance.

•Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a fire, personal injury or electrical shock.

In cold weather shipping and storage conditions, make sure that oven is in final location at least three (3) hours before switching on power. Switching on power while oven is still cold may damage the oven controls.

4. Electrical connection

It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance

with the National Electrical Code ANSI/NFPA No. 70-latest edition, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

Risk of electrical shock (Failure to heed this warning may result in electrocution or other serious injury.) This appliance is equipped with copper lead wire. If connection is made to aluminum house wiring, use only connectors that are approved for joining copper and aluminum wire in accordance with the National Electrical Code and local code and

ordinances. When installing connectors having screws which bear directly on the steel and/or aluminum flexible conduit, do no tighten screws sufficiently to damage the flexible conduit. Do not over bend or excessively distort flexible conduit to avoid separation of convolutions en exposure of internal wires.

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on the power.

(If your appliance is equipped with a white neutral conductor.)

This appliance is manufactured with a white neutral power supply and a frame connected copper wire. The frame is grounded by connection of grounding lead to neutral lead at the termination of the conduit, if used in USA, in a new branch circuit installation (1996 NEC), mobile home, recreational vehicles, where local code do not permit grounding trough the neutral (white) wire or in Canada, disconnect the white and green lead from each other and use ground lead to ground unit in accordance with local codes, connect neutral lead to branch circuit-neutral conductor in usual manner see Figure 4. If your appliance is to be connected to a 3 wire grounded junction box (US only), where local code permit connecting the appliance-grounding conductor to the neutral (white) see Figure 3.

NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are UL-recognized for connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than the wire gauge alone.

Where local codes permit connecting the appliancegrounding conductor to the neutral (white) wire (US

Only) (see figure 3):

1.Disconnect the power supply.

2.In the junction box:

connect appliance and power supply cable wires as shown in Figure 3.

Cable from Power Supply

White Wire (Neutral)

Red

Wires

Ground Wire

(Bare or Green Wire)

Black

Wires

Junction

Box

White Wire

(Neutral)

U.L.-Listed Conduit

Connector (or CSA listed)

Cable from appliance

Figure 3

3-WIRE GROUNDED JUNCTION BOX

4

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(27" and 30" Ovens with Optional Electric or Gas Cooktop Combination)

If oven is used in a new branch circuit installation (1996 NEC), mobile home, recreational vehicle, or where local codes DO NOT permit grounding through the neutral (white) wire, the appliance frame MUST NOT be connected to the neutral wire of the 4-wire electrical system. (see figure 4):

1.Disconnect the power supply.

2.Separate the green (or bare copper) and white appliance cable wires.

3.In the junction box:

connect appliance and power supply cable wires as shown in Figure 4.

Cable from Power Supply

Ground Wire

Red	White Wire
Wires
	Black
Ground Wire	Wires
(Bare or Green
Wire)	White Wire
Junction Box	U.L.-Listed
Cable from appliance	Conduit Connector
	(or CSA listed)
Figure 4

4-WIRE GROUNDED JUNCTION BOX

Model and Serial Number Location

The serial plate is located along the interior side trim of the oven and visible when the door is opened.

When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your oven.

Single Wall Oven

Serial Plate Location

Double Wall Oven

Serial Plate Location

5. Cabinet Installation

IMPORTANT!

Do not lift or manipulate the oven by the door handle or the control panel.

Heavy Weight Hazard

•Use 2 or more people to move and install wall oven.

•Failure to follow this instruction can result in injury or damage to the unit.

1Unpack the wall oven. Remove the bottom trim taped on the oven top panel.

2Find the 2 anti-tip mounting screws included in the literature package.

3Insert the oven into the cabinet opening. Slide

oven inward leaving 1½" (3.8 cm) clearance between the oven and front of cabinet (see Figure 5).

4Pull the armored cable through the hole for it in the cabinet and toward the junction box while moving the appliance inward.

5Push the oven in and against the cabinet.

1½" (3.8 cm) clearance between unit and front of cabinet.

Figure 5

5