Kenmore Elite 66517283400, 66517283402, 66517284400, 66517282400, 66517282402 Installation Guide

...
0 (0)
j masEm
8563461
8563461
TabUe of Contents
Dishwasher Safety ................................. 2
installation Requirements ........................... 3
Tools and parts ................................. 3
Location Requirements .......................... 3
Drain Requirements ............................. 5
Water SuppHy Requirements ...................... 5
EHectricaH Requirements .......................... 5
Installationinstructions............................. 6
Prepare cabinet opening
using existing utility hookups ..................... 6
where there are no existing ufiHity hookups .......... 7
Prepare dishwasher ............................. 9
Make electrical connection ...................... 12
Connect to water supply ........................ 13
Connect to drain ............................... 14
Secure dishwasher in cabinet opening ............. 14
Dishwasher Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol,
This symbol alerts you to potential hazards that can kill or hurt you and others,
Al! safety messages will follow the safety alert symbol and either the word "DANGER" or 'WARNING,"
These words mean:
You can be killed or seriously injured if you don't immediatemy
folmow instructions.
You can be killed or sedousmy injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until compmetemy installed.
Do not push down on open door.
Doing so can resultin serious injury or cuts.
You need to:
®Slowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack Close dishwasher door until latched.
Observe all governing codes and ordinances.
®Install this dishwasher as specified in these instructions.
o Installation should be performed by a qualified service
technician.The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
Installation Requirements
TooJs and Parts
Gather the required toois and parts before starting
installation. Read and follow the instructions provided with
any toois Hsted here.
AH installations
Tools needed:
+piiers
+PhHHps screwdriver
+5/16" and 1/4" nut drivers
or hex sockets
+measuring tape or ruier
+10" adjustabie wrench that
opens to 1-1/8" {2.9 cm)
+fiat-Made screwdriver
®utility knife
+2 twist-on wire connectors
which are the proper size
to connect your househoH
wiring to 16+gauge wiring
in dishwasher
+small level
®flashlight
+ shallow pan
+ electric drill with 3/32" bit
+ 5/8" open-end wrench
+ bath towel
+ wood block
Parts needed:
+90° elbow with 3/8" N,RT,
external threads on one
end, (The other end must
fit your water supply line,}
+Teflon x tape or pipe joint
compound
+shims (if installed with
built-up floor)
mnaddition, for new installations
Tools needed: Parts needed:
®electric drill with 1/2", 3/4"
and 1-1/2" hole saw bits
+ small tubing cutter
+ wire stripper
+ 1-1/2"-2" screw-type clamp
if connecting to waste+tee
+ copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
+ clamp connector or
conduit connector to fit a
7/8" (22 cm) diameter hole
Parts supplied
A. 2 - drain hose clamps, 1 large and 1 small
B. 2 - # 10 x 1/2" Phillips-head screws
C. drain hose
D. on some models, carton containing handle, Allen wrench
and 3 set screws
B
Make sure all these parts are included. If not included, call
1-800-4MY:HOME.
See separate parts list for accessories available for your
dishwasher.
Location Requirements
Do not run drain lines, water lines or electrical wiring
where they can interfere with or contact dishwasher motor
or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.This may also be obtained by calling
1-80O-4MY-HOME.
Check location where dishwasher will be installed.The
location must provide:
+ easy access to water, electricity and drain.
+ convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
+ square opening for proper operation and appearance.
+ cabinet front perpendicular to floor.
+ level floor. (if floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwashery
NOTE:To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Cutout dimensions" section.
HeJpfulTip: if the floor in the dishwasher opening is
uneven {example: tile flooring only partway into
opening) you will need to take special care in
measuring dimensions and in leveling dishwasher.
@Teflon is a registered trademark of E.I. Du Pont de Nemours and
Company.
3
Product dimensions
3/4" (1.9 cm) --_
insulation -
may be
compressed
(not used on all
models)
_-----24-1/2" (62.2 cm)_
23-7/8" (60.6 cm)
REAR VIEW
Cutout dimensions
--------------------____
All surfaces must be free
/'-- from intrusions
(5.1 cm) 10"
(25.4
2-3/4" 3-1/4"
(7 cm) (8.3 cm) (8.3 cm) (7 cm)
Cut holes in shaded area of cabinet walls or floor as specified below:
water line - 1/2" (1,3 crn)
drain line- 1-1/2" (3,8 cm)
direct wire - 3/4" (!,9 crn)
power supply cord - 1-1/2" (3,8 cm)
34 _l
(86.4 cm)
min.
Measured from the lowest point on the underside of countertop. May be
reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
Minimum, measured from narrowest point of opening.
May be increased to 6-5/8" (15.6 cm) if height of opening is 34-1/2"
(876 cm) at its lowest point.
J
Drain Requirements
o Use the new drain hose suppHbd with your dishwasher.
IftMs is not [ong enough, use a new drain hose with a
maximum [ength of 12 feet (3.7 m) that meets all[
current AHAM/[APMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain
connector of the dishwasher.
o Connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor, it is recommended that the
drain hose either be looped up and securely fastened
to the underside of the counter, or be connected to an
air gap.
air gap
o Use an air gap if the drain hose is connected to house
plumbing lower than 20" (50.8 cm} above subfloor or
floor.
o Use 1/2" minimum I.D. drain line fittings.
Water SuppJy Requirements
_A hot water line with 20-120 psi (138-862 kPa) water
pressure.
o 120°F (49°C) water at dishwasher.
o 3/8" O.D. copper tubing with compression fitting or
flexible stainless steel braided fill line (1/2" minimum
plastic tubing is not recommended).
o A 90 ° elbow with 3/8" N.RT. external pipe threads on
one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
EJectricaJ Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with aii national and local codes and
ordinances.
You must have:
o 120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical
suppl%
®Copper wire only.
We recommend:
o A timeodelay fuse or circuit breaker.
o A separate circuit,
ff direct wiring dishwasher:
Use flexible, armored or nonometallic sheathed, copper
wire with grounding wire that meets the wiring
requirements for your home and local codes and
ordinances.
Use strain relief method provided with house wiring
junction box or install a U.L.-listed/CSAocertified clamp
connector to the house wiring junction box. if using
conduit, use a U.L.-listed/CSA-certified conduit connector.
_fconnecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part No. 4317824} marked for
use with dishwashers. Kit contents include:
-Volex, inc., UL listed 16 gauge 3 wire power supply
cord with 3 prong grounded plug.
- Neer C-500 7/8 inch strain relief.
- 3 wire connectors.
- Part No. 302797 grommet
Follow the kit instructions for installing the power
supply cord.
o Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
/nstM/ation instructions
EBectricat Shock Hazard
Disconnect e{ectricam power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result }n death or emectr}ca{ shock,
1. Disconnect power.
2. Turn off water suppiy.
Prepare cabinet opening using
existing utility hookups
Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
®If you are installing the dishwasher in a cabinet opening
that does not have hookups, follow the steps under
"Prepare cabinet opening where there are no existing
utility hookups" section.
1. Check that the water
line reaches to the
front left of opening
where the water
connection will be
made.
2. Check that the direct _
wire reaches to the
front right of opening 6" (15.2 cm)
where the electrical
connection will be made.
If the water line and the direct wire reach far enough into
the opening, proceed to the next section "install the drain
hose/' If they do not reach far enough, follow the steps
under "Prepare cabinet opening where there are no
existing utility hookups:'
mnstaH the drain hose
IMPORTANT: Always use a new drain hose even when
installing a new replacement dishwasher,
1. Drill a 1-1/2" (3,8 cm) diameter hob in cabinet wall or
floor on the side of the opening closest to the sink
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer-with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer - no air gap
Option 4, No waste disposer - no air gap _
_anair gap is recommended
HeJpfulTip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer - with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clampX.
3. Use a rubber hose connector _ with spring or screw-
type clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at
bast 20" (50.8 cm) above the floor where dishwasher
will be installed,
drain hose -
cut here if needed
rubber hose
ector
gap
large
J spring-type
clamp
_ drain
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made,
drain hose
Parts available from local plumbing supply stores
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with [arge spring-type
champ, if the drain hose was cut, use a 1-1/2" to 2"
(&8 to 5 cm) screw-type cHamp x,
3. Use a rubber hose connector _ with spring or screw-
type damps .×.to connect air gap to waste tee_
This connection must be before the drain trap and at
[east 20" (50.8 cm) above the floor where dishwasher
wH[ be instaiied_
drain hose-
cut here if needed
rubber hose
connector
large
spring4ype
waste
tee drain
drain trap hose
4. insert drain hose |
through hob cut in
cabinet to the front
center of opening where
drain connection will be /
made.
drain hose
Parts available from local plumbing supply stores
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring_
type damp.
This connection must be before the drain trap and at
ieast 20" (50.8 cm) above the floor where dishwasher
wiii be instaiied, it is recommended that the drain hose
be iooped up and secureiy fastened to the underside of
the counter.
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. insert drain hose |
through hole cut in
cabinet to the front
center of opening where
drain connection wiii be
made.
drain hose
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to waste tee with lq/2" to 2"
(3.8 to 5 cm) screw-type ciampX.
This connection must be before the drain trap and at
bast 20" (50.8 cm) above the floor where dishwasher
wiii be instaiied, it is recommended that the drain hose
be iooped up and secureiy fastened to the underside of
the counter.
3. Insert drain hose
through hoie cut in
cabinet to the front
center of opening where
drain connection wiii be
made.
drain hose
Parts available from local plumbing supply stores
Prepare cabinet opening where there
are no existing utility hookups
Electrical connection
Option1, Direct wire method:
HeJpfu_Tip: Wiring the dishwasher wiii be easier if you
route wire into the cabinet opening from the right side.
1. Drill a 3/4" (1.9 cm) optional preferred
hob in right-hand locations locations
cabinet side, rear or
floor. Preferred and
optionai iocations are
shown.
2. Wood cabinet: Sand
hob until smooth.
3,
4.
5,
Metai cabinet: Cover
hob with grommet, not provided.
Run wire into house wiring junction box.
Instaii a U.L.qisted/CSA-certified champ connector
(strain reiief) for fiexibie-type wire. If inataiiing conduit,
attach a U.L.qisted/CSA-certified conduit connector to
the junction box.
Run other end of wire
through cabinet hoie.
Cabie must extend to the
right front of cabinet
opening.
Option2, Powersupplycordmethod:
NOTE:Amating,threeprong,ground-typewanreceptacb
isrequiredinacabinetnextto thedishwasheropening.
1. DrHHa1ol/2"
(3.8cm)hobin optionalpreferred
thecabinetrear locationslocations
orside,Preferred[ii_i
andoptional ......
bcafionsare
shown.
2. VVoodcabinet:
Sandhobuntil
smootL
Metai cabinet: Cover hone with grommet (Part No.
302797) inciuded with power suppiy cord kit.
mnstall the water line
NeJpfuJTip: Routing the water Hne through the Heftside
of cabinet opening will make water connection easier.
Drill a minimum 1/2" {1.3 cm) hole in the cabinet side,
rear or floor. Preferred and optional locations are
shown.
preferred
locations
optional
locations
2. Measure overall length
of copper tubing
required.
3. Attach copper tubing
to the water line with a
manual shutoff valve.
copper
tubing
4. Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be
gentle.The copper tubing should be far enough into the
cabinet opening to connect it to dishwasher inlet on the
front left of the dishwasher.
5. Turn water shutoff valve to "ON" position. Flush water
into a shallow pan to get rid of particles that may clog
the inlet valve.
6. Turn shutoff valve to "OFF" position.
mnstaH the drain hose
IMPORTANT: Always use a new drain hose.
1, Drill a 1-1/2" (3,8 cm)
diameter hole in
cabinet wall or floor on
the side of the opening
closest to the sink
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer-with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer - no air gap
Option 4, No waste disposer - no air gap _
_anair gap is recommended
HeJpfu_Tip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer = with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section}.
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp x.
3. Use a rubber hose connector _ with spring or screw-
type chmps x to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
spring-type
clamp
"" drain
hose
drain trap
E
4. Insert drain hose | drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be / ...................
made.
Parts available from local plumbing supply stores
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with Harge spring-type
champ. If the drain hose was cut, use a 1-1/2" to 2"
(&8 to 5 cm) screw-type cHamp x,
3. Use a rubber hose connector _ with spring or screw-
type champs .×.to connect air gap to waste tee_
This connection must be before the drain trap and at
Heast20" (50.8 cm) above the floor where dishwasher
wHHbe instaHHe&
. drain hose-
cuthereif needed
springor
rubber hose
connector
large
spring4ype
waste
tee drain
drain trap hose
4. hsert drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wHHbe
made,
ZL drain hose
Parts available from local plumbing supply stores
Option 3, Waste disposer = no air gap:
1. Remove the disposer knockout pHug. Do not cut end of
drain hose.
2, Attach drain hose to disposer inlet with large spring_
type clamp,
This connection must be before the drain trap and at
least 20" (50,8 cm) above the floor where dishwasher
will be installed, It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter,
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made,
drain hose
Option 4, No waste disposer - no air gap:
1, Cut end of drain hose if needed (do not cut ribbed
section),
2, Attach drain hose to waste tee with lq/2" to 2"
(3,8 to 5 cm) screw-type ciampX,
This connection must be before the drain trap and at
least 20" (50,8 cm) above the floor where dishwasher
wiil be installed, it is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter,
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made_
l/if drain hose
Parts available from local plumbing supply stores
Prepare dishwasher
Tip Over Hazard
Do not use dishwasher untim cornpletemy installed.
Do not push down on open door.
Doing so can result in serious iniury or cuts,
Put corner posts from packaging behind dishwasher,
Grasp sides of dishwasher door frame and put
dishwasher on its back, resting on top of the corner
posts,
2. Remove two screws attaching access paneH and bwer
panei to dishwasher using a 1/4" hex socket, nut driver
or PMHips screwdriver.
3. Remove paneHs and set paneHs aside on a protective
surface.
4. Check that grounding chip is attached to the bwer
panel,
lower
panel
clip
water inlet valve
5. AppiyTefion :" tape or pipe
joint compound to 90 ° eibow
fitting and connect fitting to
water iniet vaive.
& Tighten elbow until snug, and
be sure that it faces to the
rear.
7. Remove terminal box cover. Puii appliance wires
through hoie in terminai box. Do not untie the knot in
the wires.
- if you are direct wiring: install a U,h-listed/CSAo
certified damp connector to the terminai box, if using
conduit, use a U,L,olisted/CSAocertified conduit
connector,
- if you are installing a power suppiy cord kit, do so
now, following kit instructions,
dishwasher
wires --...
\
cable clamp connector
HeJpfuJTip: Put cardboard under dishwasher until it is
instaiied in cabinet opening.The cardboard wiii heip
protect floor covering during instaiiation.
8. Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be
instaiied (you need the iowest
point). Check chart for that height
opening. Put wheeis in the required
position.
wheel
Number of
Minimum Wheel
turns on
cutout height position front leg
34" (86.4 cm) 1 10
34-1/4" (87 cm) 2 5
34-I/2" (87.6 cm) 3 0
8,
Turn both front ieveier iegs to the same
height.
If the minimum cutout height is less than
34" (86.4 cm), the rear wheels can be
removed for additionai ciearance.This wiii
aiiow the dishwasher to fit into a 33-7/8"
(86 cm) high cutout, but the dishwasher
wiii be more difficult to move into
position, if the wheeis are removed,
protect the floor when moving the dishwashen
frontleg
If you have built-up
floors
1. Measure height of opening
from underside of
countertop to buiit-up
floor, if the height is at
bast 33o3/4" (85.7 cm), the
dishwasher will fit into the
opening without
modification to the
countertop or flooring.
2. Put wheels in position 1
j countertop
rr
33-3/4"
(65,7 cm)
min.
3,
and turn the front ieveier iegs up aii the way.
Add shims as needed in the area shown to bring
dishwasher up to proper height.
NOTE: Shims must be secureiy attached to floor to
prevent their movement when the dishwasher is
operated.
2"
(5,1 cm)
shim shim
2-3/4" 6"
(7.0cm) (15,2cm) (ZOcm)
mnstaH ¢ustorn door panel kit (on some models)
If instaiiing a custom door panei kit, instaii it now foiiowing
instructions included with kit,
10
mnstall the door handle (onsomemodels)
IMPORTANT: Do not scratch the front panei during this
procedure.
1. Remove the door handie and hardware bag containing
the setscrews and Aiien wrench from the cardboard box.
2. Start set screws in handHe.
3. Piace handie on mounting studs.The handie shouid
appear as a "smile" when instaHHed, with the set screws
facing down.
4. Push the door handie tightly against the door. insert the
short end of the AHHen wrench into the setscrews.
Tighten the setscrews 1/4 turn past snug. Retain AHHen
wrench with HnstaHHafion Instructions
stud
@
handle
setscrew I
(in bottom
of handle)
wrench
Choose attachment option
Using two or more people, stand the dishwasher up,
Option 1, Countertop attachment
The dishwasher must be
secured to the cabinet.There
are two brackets on top of the
dishwasher that can be
attached to the countertop if it
is wood, iaminate or other
simiiar surfaces. If this is not
possibie, the brackets may be
moved to the sides of the
dishwasher.
NOTE: Do not attach the
dishwasher, this wiii be done
Hater.
brackets
front vent
model shown
Option 2, Dishwasher side attachment
(for marble, granite or other hard surface
countertop)
1. To remove the brackets from the top, flatten tab at back
of brackets with pliers, and pull the brackets out of the
slots,
2. Break offthe end of the bracket aiong the scored line.
score
line
3. Open dishwasher door and piace towei over pump
assembiy and spray arm of dishwasher.This wiii
prevent screws from farthing into pump area when
securing dishwasher to cabinet.
4. Push the piastic buttons out of the side of the tub.
NOTE: Save the buttons to cover the hobs after
dishwasher is instaiied.
5. Push bracket into slot on the side of dishwasher, and
bend tab in towards the side of the dishwasher so that
it keeps the bracket in piace.
NOTE: Do not attach the dishwasher, this wiii be done
Hater.
bend i
tabs
Move dishwasher into cabinet opening
1,
2.
3,
Grasp the sides of the dishwasher
at the edges of the door panei.
Tilt dishwasher backwards on
wheeis and move dishwasher chose
to cabinet opening. Do not push on
the front of the panei or on the
consoie--they may dent.
If dishwasher has a power supply
cord, insert power supply cord into hole cut into
cabinet.
If using direct wire, check that it is on the right front
side of opening.
11
4. Checkthatwaterlineisontheleftsideofopeningand
drainhoseisnearthecenteroftheholeinthecabinet.
5. Slowly move dishwasher completely into cabinet
opening. Do not kink or pinch copper tubing, drain
hose, power supply cord or direct wire between
dishwasher and cabinet.
HeipfuJTip: Once the dishwasher is in position, you
may have to support the front of the dishwasher by
raising, lowering or shimming front feet.
6. Remove cardboard from under dishwasher,
NOTE: it is all right if dishwasher fits tightly into cabinet
opening. Do not remove insulation blanket --the blanket
reduces the sound level.
Check door spring tension
1. With another person holding the dishwasher to prevent
it from tipping, open and close the door a few times, if
the door closes or falls open under its own weight, the
door tension will need to be adjusted.
2. To adjust the door spring tension, unhook the spring
from the rear leg of dishwasher.
3. With a 5/16" nut driver or hex socket, remove the screw
from the tensioner.
4. The screw can be put into one of three holes D, F_Jl,D
in front leg of dishwasher. If the door closes by itself,
move the tensioner to a higher number hole and
replace screw. When door is unlatched, if it opens by
itself, move tensioner to a lower numbered hole and
replace screw.
5. Re-attach door spring to rear leg.Tensioners on both
sides of dishwasher should be secured at same holes.
spring
screw
LeveU the dishwasher
Align front of dishwasher door panel with cabinet
doors.You may need to adjust alignment to be even
with your cabinets.
He[pfu[Tip: Prop up one side of frame to hold
dishwasher up off floor when adjusting front legs,
2. Check that leveling legs are firmly against the floor.
3. Close and latch the door, and place level against the
front panel. Check that dishwasher is plumb, if needed,
adjust leveling leg or add shims under rear wheel until
dishwasher is plumb.
4. Repeat for other side of dishwasher,
NOTE: Shims must be securely attached to floor to prevent
their movement when the dishwasher is operated,
5. Place level against top front
opening of tub, Check that
dishwasher is level from side to
side, If dishwasher is not level,
adjust front legs up or down until
dishwasher is level,
Make EJectricaJ Connection
Check "Electrical requirements" section.
You need to:
o have the correct electrical supply and recommended
grounding method.
if you are:
o direct wiring, use Option 1
o using a power supply cord, use Option 2
Option 1, Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor or lower part of dishwasher tub,
2. Pull direct wire through hole in terminal box,
Helpful Tip:
o Select the proper size twist-on
connectors to connect your household __
wiring to 16-gauge dishwasher wiring,
o Insert wire ends into twist-on
connector, Do not pre-twist bare wire,
oTwist connector,
o Gently tug on wires to be sure both are __
secured,
12
3. Connect the wires as follows using twist°on connectors
sized to connect direct wire to 16-gauge dishwasher
wire:
Powersupply wire: Terminal box wire:
white_-_white
Nack_Nack
ground wire_<-4_gr0und connector
Electdcam Shock Hazard
Emectrically ground dishwasher.
Connect ground wire to green ground connector in
terminam box.
Do not use an extension cord,
Failure to folmow these instructions can resumt in death,
fire, or electrical shock.
4. Form bare ground wire into a U-shaped hook, Wrap
ground wire hook cbckwise around ground connector
and under the washer,
5. Secureiy tighten ground connector. Do not untie knot in
the wires.
ground wire washer
ground
connector
ground wire
6. Tighten clamp connector or
conduit connector screws.
Reinstall terminal box cover with
wires inside terminal box,
The cover must be outside the box
on the left side,
8. Make sure no wires are pinched by cover.
Option 2, Power supply cord method
Emectricam Shock Hazard
Plug into a grounded 3 prong outmet,
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord,
Faimure to follow these instructions can result in death,
fire, or emectrica_ shock.
1. Plug into a grounded 3 prong outlet.
2. Check that power supply cord does not touch
dishwasher motor or lower part of dishwasher tub.
Connect to water suppJy
Helpful Tip:
Compression fittings:
a. Slide nut onto copper tubing about 1" (2.5 cm).
b. Slide ferrule onto the tubing. Do not position ferrule
on the end of the tubing.
c. Put the tubing into the elbow as far as it will go.
d. Slide the nut and ferrule forward and start the nut
onto the elbow threads. Be gentle when handling
and positioning the copper tubing, it bends and kinks
easily.
elbow
nut
1. To prevent vibration during operation, route the water
supply line so that it does not touch the dishwasher
base, frame or motor.
2. With copper tubing pushed into compression fitting as
far as it will go, use a wrench and tighten compression
fitting nut to elbow on water inlet valve.
3. Place paper towel under elbow.Turn on water supply
and check for leaks.
13
Connect to drain
1. To heHp minimize
vibration, route drain
hose to avoid contact
with motor, door springs,
water Hine, cabinet,
flooring or the edge of
the hoHe where it passes
through the cabinet,
2. Do not remove drain
Hoop from side of
dishwasher_
3. Hace pan under end of drain hose. Pan wHHcollect any
water in drain hose.
4. Remove pHug and paper from drain connector.
NOTE: Cutting the zip tie hoHding the end of drain hose
in pHace may make maneuvering the drain hose easier
during installation.
zip tie
5. Hace the smaller drain hose
champ onto the small end of the
drain hose.
hose
/J clamp
6. Push the drain hose into the connector up to the stop
on the drain hose,
connector stop
7. Use pliers to open clamp and slide clamp onto
connector between stops on connector as shown,
hose clamp
,j
stops
Secure dishwasher in cabinet opening
2,
3.
Tip Over Hazard
Do not use dishwasher antim completely installed.
Do not push down on open door,
Doing so can result in serious iniury or cuts.
If you have not already done so, open dishwasher door
and place towel over pump assembly and spray arm of
dishwasher.This will prevent screws from falling into
pump area when securing dishwasher to countertop.
Check that dishwasher is still level and centered side to
side in the opening.
Secure dishwasher to countertop or sides of cabinet
with two, #10 x 1/2" Phillips-head screws.The
dishwasher must be secured to keep it from tipping
when door is opened. Do not drop screws into bottom
of dishwasher.
OR
d
4. Open door about 3 inches (7.6 cm) and check that space
between inner door and tub is equal on both sides. If
spacing is not equal, loosen bracket screws and shift
tub.Tighten bracket screws.
5. Check that top of door does not contact screws,
brackets, or countertop. If it does, dishwasher must be
lowered and reoleveled.
6. If securing to sides of cabinet, replace the plastic
buttons.
7. Remove towel from dishwasher,
8. Reinstall the lower dishrack
14
Bottom sound pad instaJJation (on some modeHs)
1. Remove the bottom sound pad from inside the
dishwasher and take it out of the pHasfic bag.
2. Hace pad on the floor in front of the dishwasher,
making sure Hettedng is facing up and vinyH pad faces
down.
3. FoHd up and hoHd the side paneHs down. CarefuHHy sHide
the pad toward the back of the dishwasher as far as it
vvHHgo, making sure not to push or puHHany wires or
hoses. (Do not force.) Side paneHs wHH open to proper
position.
NOTE: If there are pipes or other obstructions coming
up through the floor, you wHH need to cut a sHit in the
pad to fit around the obstacHe.
\
...._i;!!_!_!_!_!_!_!_!_i_!i_iiiiiiiii_ii_!!_iiiiiiiiiiiiiii_i_iiiiiiiiiiiiiiii_i_!_!_i_ii_i
....... !i !i !ii!ii!;! i! i! !i ii i! ! ! !ii!ii!iiiiiiliiiiiiiiiiiiiiii!i
4. Fold the front end of the pad up into position. Make
sure the vinyl pad is tucked up behind the door and the
dishwasher front legs, as shown.
Complete installation
1. Check that grounding clip is attached to the lower
panel.
2. Place the lower panel behind the access panel. Some
models have insulation on the access panel which must
fall behind the insulation on the lower panel.
grounding
clip
3. HoH the two panels together and place them against
dishwasher leg.
4. Reinstall the screws through the holes in the access
panel and the slots in the lower panel, install right side
screw first.
5. Check that the lower edge of the lower pane[ contacts
the floor.
6. Tighten the screws.
Direct wire method:
Emectrica_ Shock Hazard
EmectricaHy ground dishwasher.
Connect ground wire to green ground connector in
terminam box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or emectricamshock.
Power suppJy cord method:
EmectricaJ Shock Hazard
Plug into a grounded 3 prong outmet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or emectrical shock.
7. Reconnect power or plug in dishwasher.
15
Loading...
+ 33 hidden pages