Kenmore 66513692N410, 66513693N410, 66513699N410, 66512833K311, 66512833K312 Installation Guide

...
0 (0)
Installation Instructions
Instrucciones de instalaci6n
Instructions d'installation
English / Espafiol / Fran_ais
I<enmore
@ @
@
¢C _F
P/N W10300759C Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A. www.kenmore.com www.sears.com
Sears Canada Inc. Toronto, Ontario, Canada M5B 2C3
www.sears.ca
TABLEOF CONTENTS
DISHWASHER SAFETY ............................................................. 2
INSTALLATION REQUIREMENTS ............................................. 3
Tools and Parts...................................................................................3
Location Requirements ..................................................................... 4
Drain Requirements ...........................................................................6
Water Supply Requirements ...........................................................6
Electrical Requirements ....................................................................6
INSTALLATION INSTRUCTIONS ............................................. 7
Prepare Cabinet Opening--Existing Utilities .............................. 7
Prepare Cabinet Opening--New Utilities ................................... 7
Prepare and Route Water Line.......................................................8
Install Drain Hose ...............................................................................9
Prepare Dishwasher .........................................................................11
INSTALLATION INSTRUCTIONS (CONT.)
Make Power Supply Cord Connection .........................................13
Determine Cabinet Opening ......................................................... 14
Custom Panel Installation ................................................................15
Choose Attachment Option ............................................................15
Move Dishwasher Close to Cabinet Opening ............................ 16
Connect to Water Supply ............................................................. 18
Connect to Drain ............................................................................. 19
Make Direct Wire Electrical Connection ................................... 20
Secure Dishwasher in Cabinet Opening ......................................21
Complete Installation ......................................................................23
Check Operation .............................................................................25
If Dishwasher Does Not Operate .................................................25
Additional Tips.................................................................................25
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured ifyou don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
You Need to:
Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain hose
and lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Tip Over Hazard
Do not use dishwasher until completely installed. Do not push clown on open door.
Doing so can result in serious injury or cuts.
Installation should be performed by a qualified service technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and ordinances.
2
INSTALLATION REQUIREMENTS
Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any
tools listed here.
All Installations Tools needed:
Parts needed:
3 _l 3 _J
Y8 Comprx Y4 hose
fitting: ContaCt your !ocal
sears store t0 purchase Kit Number 1100g.
Pliers
Phillips screwdriver
5A6"and 1/4" nut drivers or _Sr _
hex sockets
or ruler
Measuring tape _
10" adjustable wrench
tha! opens to _//-_
11/8 (2.9 cm)
Torx ®*T20 _ screwdriver
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher.
Other useful items you may need:
[Flashlight_ Shallow _ Bath _-_i
Parts supplied:
Drain hose Iuram clamps (2) inose
(1 large and 1 small)
#10XwI 2- under-
Phillips.head counter screws (2)mounting
Flat-blade screwdriver
Utility knife
UL Listed/CSA
Approved twist-on _ _
wire connectors*
Small level
%" open-end wrench
brackets
Other parts you may also need:
--2 _ I Masking Orl
(3.81w5 cm) I duct tape
sc e :type I
[il/2" "
ClamPS (3 maximum)1
NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that electrical connections be made by a licensed electrical installer.
In addition, for first-time installations
Toolsneeded:
Cordless drill With 1/2,3/4
1
and 1V2 hol_ saw bits
Parts needed:
Copper tubing (%'! see "Electrical Requirements" section: O.D.suggested) or I
flexible [)raided For Direct Wire: For PoWer Supp!y Water supPly line use UL L!sted/ cord: use UL
(,[._._k._._ _)_))_') I tofit% (2.2cm) supply cordkit
"_-_'__/ I hole marked for use With
CSA Approved Listed/CSA
I strain APPr°ved power
I 'dishWasher
I
Make sure all these parts are included in the literature package.
1-®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.
Grounded electrical supply required. Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch the floor.
Do not install dishwasher over carpeted flooring. Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The location must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: Flooring extends only partway into
opening). NOTE: To avoid shifting during dishwasher operation, shims
must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area shown in the "Product and Cabinet Opening Dimensions" section.
4
Product and Cabinet Opening Dimensions ..................................................................................................................................................................
/j _I_
*Insulation may be compressed
(not used on all models)
NOTE: Shaded areas of cabinet wails show
where utility connections may be installed.
*Measured from the lowest point on the
underside of the countertop. May be reduced to 331/2" 85 1 cm b
( . ) y removing the
wheels from dishwasher.
**Minimum, measured from narrowest point J
of opening.
Check that all surfaces have no protrusions that would prohibit dishwasher installation.
t1.5
p _J
.dot _
D _!__}Req_,,_ _e_e_}_ _
A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is
resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.
Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the
underside of the counter, or be connected to an air gap.
Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical
Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association 1Batterymarch Park Quincy, MA 02169-7471
You must have=
120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical supply.
Copper wire only.
We recommend=
A time-delay fuse or circuit breaker.
A separate circuit.
If connecting dishwasher with a
power supply cord:
Use UL Listed power supply cord kit (Part Number 4317824) marked for
use with dishwasher.
Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or
floor. Use 1/2" minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.
A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher. 3/8"O.D. copper tubing with compression fitting or flexible
braided water supply line (Part Number 4396897RP). NOTE: 1/2"minimum plastic tubing is not recommended.
A 90 ° elbow with 3/4" hose connection with rubber washer.
Power supply cord must plug into a grounded 3 prong outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all local codes and ordinances.
If connecting dishwasher with direct wiring:
Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for your home and local codes and ordinances.
Use a UL Listed/CSA Approved strain relief.
Do not solder within 6" (15.2 cm) of the water inlet valve.
6
INSTALLATION
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
INSTRUCTIONS
If the water line and the cable extend to the locations shown,
proceed to the "Install Drain Hose" section. If they do not reach far enough, follow the instructions in the "Prepare Cabinet
Opening--New Utilities" section.
x x ¸ i
_FoIIow instruCtions in the !,Prepare Cabinet
Opening'Existing UtilitieS' ! section,
No _Follow instructions inthe ,Prepare cabinet
Opening--New Utilities sectionl
Prepare and route the electrical supply
Option hv Power SupplyCord=
NOTE: A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening.
j Power Supply Cord--Drill
Optibnal location
r
,cation
Drill a 1½" (3.8 cm) hole in cabinet side or rear. See "Product and Cabinet Opening Dimensions" section.
Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet included with power
supply cord kit.
Option B,Direct Wire,
Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape
cable to the floor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening.
Helpful Tip: Wiring the dishwasher will be easier if you route the cable into the cabinet opening from the right-hand side.
Drill a 11/2" (3.8 cm) hole in right-hand cabinet side or rear. See "Product and Cabinet Opening Dimensions" section.
Helpful Tip: Routing the water line through the left side of cabinet opening will make water connection easier.
Drill a 1/2"(1.3 cm) hole in the cabinet side or rear.
Measure water supply
(copper tubing only)
Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet (Part Number 302797
- not provided).
Measure overall length of copper tubing for the water supply line.
Loading...
+ 17 hidden pages