Kenmore 66513692N411, 66513692N412, 66513693N411, 66513693N412, 66513699N411 Installation Guide

...
0 (0)
Installation instructions
Instrucciones de instalaci6n
instructions d'installation
Engllsh / Espa_ol / Fran_als
I en more Elite
_/_iC_ =_° _'_ _, _,-o_=,_
H _I I,_,_I
e ®
F
P/N W10747788A
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U,S,A,
www.kenmore.com
www, sears,com
Sears Canada tnc,
Toronto, Ontario, Canada M5B 2C3
WWW, Sea rs,ca
TABLEOF CONTENTS
DISHWASHER SAFETY ............................................................. 2 Make Power Cord Connection .......................................................13
iNSTALLATiON REQUIREMENTS ............................................. 3
Tools and Parts...................................................................................3
Location Requirements ..................................................................... 4
Drain Requirements ...........................................................................6
Water Supply Requirements ...........................................................6
Electrical Requirements ....................................................................6
iNSTALLATION INSTRUCTIONS ............................................. 7
Prepare Cabinet Opening--
Existing Utilities ................................................................................. 7
Prepare Cabinet Opening--New Utilities ................................... 7
Prepare and Route Water Line.......................................................9
Install Drain Hose.............................................................................10
Install Optional Moisture Barrier ..................................................12
Prepare Dishwasher ........................................................................12
Determine Cabinet Opening ..........................................................15
Install Door Handle .........................................................................16
Custom Panel Installation ...............................................................16
Choose Attachment Option ........................................................... 17
Prepare Water Supply Line........................................................... 17
Move Dishwasher Close to Cabinet Opening ............................ 18
Connect to Water Supply ............................................................ 20
Connect to Drain ............................................................................ 20
Make Direct Wire Electrical Connection .....................................21
Secure Dishwasher in Cabinet Opening .....................................23
Complete installation ..................................................................... 24
Check Operation .............................................................................26
If Dishwasher Does Not Operate .................................................26
Additional Tips.................................................................................26
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You Need to=
[] Slowly open dishwasher door while someone grasps the rear
of the dishwasher. Remove shipping materials and drain
hose. Close dishwasher door until latched.
NOTE: Each dishwasher is tested at the factory and may
contain some residual water in the tub as a result of the test.
[] Observe all governing codes and ordinances.
[] Install this dishwasher as specified in these instructions.
[] Installation should be performed by a qualified service
technician.
[] The dishwasher must be installed to meet all electrical and
plumbing national and local codes and ordinances.
Care shall be exercised when the appliance is installed or
removed, to reduce the likelihood of damage to the power cord.
WARNING= To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher is
completely enclosed at the time of installation.
2
iNSTALLATiON
Gather the recommended took and parts before starting
installation. Read and follow the instructions provided with any
took listed here.
All Installations
Tools Needed:
i F,at:b,ade
e s I screwdriver
5 " i "
_6 and V4 /_) J
nut dr!vers or _S-" JSmal!level
hex sockets __.._.._.._/ _
10', adjustab!e wrench _ 'TorX ®_T20® and, if
that opensto _ installing custom _
!'/8" (2 9 Cm)_ fr°nt.pane/s,
Torx_ T15 screwarivers
Other Useful Items You May Need:
F,ashlight__ Ba
Pa#s Suppffed:
Drain h0se Drain hose #10 X underc0unter Door
clamps (2)Phillips, mounting handle(on
(1 large/red head brackets (2) 5ome
and I smallJ __ screws (2) _m°dels)-
;Ireen) . .
Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-422-1230. In Canada, call
1-800-807-6777
REQUIREMENTS
Other Parts Needed: (not provided)
I i
%" Compression Household Wiring Twist-on Wire
x 3/4 Hose Fitting (Metallic) Strain Relief Connectors
with rubber seal to fit %" (2.2 cm) hole NOTE: Confirm
and 90°elbow (required to properly proper size for
(required to secure household connecting your
properly connect wiring to the dish- gauge of house-
household water washer terminal box) hold wiring to the
line to the NOTE: Use only UL .16-gauge wiring
dishwasher)
(Part Number
W!0685193)
Listed/CSAApproved in the dishwasher
part ,_ NOTE: Use on y
_- -3_ UL Listed/CSA
Approved parts.
(Part I ff _
Number 4396672) 'J '_
To order parts, caff 1-800-469-4663, for Part Number above,
or see local electrical/plumbing supply retailer for equivalent.
Optional Accessory Parts Available:
Moisture BarderTape
NOTE: Moisture barrier tape is
an optional, added level of
protection if installing a
dishwasher under a wooden
countertop.
(Part
Number 4396277)
Side Panel Kit
For enclosing the side of
the dishwasher when
installing it at the end of
your cabinetry.
(Part Number _
varies with
color)
To order parts, call 1-800-469-4663,for PartNumber above.
First-time Installatlons=
Check local codes. Check existing electrical supply. See the
"Electrical Requirements" section, it is recommended that
electrical connections be made by a licensed electrical
installer.
Additional Tools Needed:
Additional Ports Needed (not provided)
Coppe_ tubing (%" screw:TyPe Opti0na!,L0nge[
O,D. suggested)Clamps Drain Hose Maximum
or Rexible Braided 11/2,. 2" length: 12 ft (3.7 m)
Water Supply Line (3.8!- 5cm) NOTE:Must meet
Kit (Part Number (3 maximum) AHAM/IAPMO test
W10278635RP), Kit . standards, fit 1,
includes Braided (2,5 cm)drain
Hose and %,' connection, and be
Compression x 3/4, resistant to heat and
HoseF tt ng detergent,
1-®)TORX,T15, and T20 are registered trademarks of Acument Intellectual Properties, LLC.
To order parts; call 1.800'469_466& for part number above,
or see local electrical supply retailer for equivalent.
NOTE: If using a flexible braided hose, replace inlet hose after
5 years to reduce the risk of hose failure. Record hose
installation or replacement dates on the hose for future
reference.
For DirectWire For Power Cord
I
Cabinet Grommet Power Cord Kit
For 11/2"(3.8 cm) Kit typically incHudes power cord,
hoHe in cabinet, metallic strain relief, grommet, and
twist-on wire Connectors.
O
Number 302797) (___ Id L_
NOTE: Required
for metal cabinets. (Part Number 4317824)
oTOorder parts, call 1-800-469-4663, for Part Number above,
r see local electrical supply retailer for equivalent.
Dishwasher must be fully enclosed (top, sides, back, and floor)
upon installation. A side panel kit is available from your dealer
for installing your dishwasher at the end of your cabinetry.
An optional moisture barrier accessory is also available for
installing underneath a wooden countertop. See the "Tools and
Parts" section at the front of the guide for part details and
orders.
Check location where dishwasher will be installed. The location
must provide:
[] Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between
the side of the dishwasher door and the wall or cabinet.
[]
[]
[]
A square opening for proper operation and appearance.
The cabinet front to be perpendicular to floor.
A level floor.
Helpful Hint: If floor at front of opening is not level with
floor at rear of opening, shims may be used to level
dishwasher. NOTE: To avoid shifting during dishwasher
operation, shims must be securely attached to the floor.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
[] Do not install dishwasher over carpeted flooring.
[] Easy access to water, electricity and drain.
[] Grounded electrical supply required.
[] Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
[] Do not run drain lines, water lines or electrical wiring
where they can interfere with or contact dishwasher
motor or legs.
[] Shelter dishwasher and water lines leading to
dishwasher against freezing. Damage from freezing is
not covered by the warranty.
NOTE= If dishwasher will be left unused for a period of time
or in a location where it may be subject to freezing, have it
winterized by authorized service personnel.
4
J
31/2"-41/4''
(8.8 cm - 10.6 cm) /
For 4" (10 cm) toe (9
kick. height of cabinet
opening is 341/2'' (86.3 cm).
A. Insulation may be compressed
(not used on all models).
B. For panel-ready models, dishwasher
depth is 24" (60 cm) not including the
3/4"(1.9 cm) custom door panel.
C. Door handles may protrude forward
of the face of the dishwasher; varies
by model.
3/41
/ (1.9 cm)
A
_4
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
NOTE: Shaded areas of cabinet walls show where
utility connections may be installed
D. Measured from the Iowesl point on the
underside of the countertop. May be
redu ced to 331W (85.1 cm) by removing
the wheels and 3erforated area of insulation
(blanket) on dishwasher.
E. Minimum. measured from narrowest point of opening.
61/4 ''
/15.9cm
[]
[]
[]
A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current
AHAM!IAPMO test standards, is resistant to heat and
detergent, and fits the 1" (2.5 cm) drain connector of the
dishwasher. See the "Tools and Parts" section at the front of
the guide for part details and orders.
Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter, or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (50.8 cm) above sub floor or
floor.
[] If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap, a rubber hose (not provided) will be
needed to connect to the waste tee or disposer inlet.
[] Use 1/2" minimum I.D. drain line fittings
[]
[]
[]
[]
[]
A hot water line with 20 to 120 psi (138 to 862 kPa) water
pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
3/8"O.D. copper tubing with compression fitting or flexible
braided water supply line. See the "Tools and Parts" section
at the front of the guide for part details and orders.
NOTE: 1/2"minimum plastic tubing is not recommended.
A 90 ° elbow with 3/4"hose connection with rubber washer.
See the "Tools and Parts" section at the front of the guide for
part details and orders.
Do not solder within 6" (15.2 cm) of the water inlet valve.
Be sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical
Code, ANSI!NFPA 70 - latest edition and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1Batterymarch Park
Quincy, MA 02169-7471
You Must Have:
[] 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical
supply.
[] Copper wire only.
[] A maximum of two field wiring supply conductors (12 AWG
largest size) plus one grounding conductor are permitted in
the terminal box.
We Recommend:
[] A time-delay fuse or circuit breaker.
[] A separate circuit.
If Connecting Dishwasher With A
Power Cord:
[] Use UL Listed power cord kit
marked for use with dishwasher. See
the "Tools and Parts" section at the front of the guide for
part details and orders.
Power cord must plug into a grounded 3
prong outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all
local codes and ordinances.
If Connecting Dishwasher With Direct Wiring:
[] Use flexible, armored or
nonmetallic sheathed, copper wire
with grounding wire that meets the
wiring requirements for your home
and local codes and ordinances.
[] Use a UL Listed/CSA Approved metallic strain relief. See the
"Tools and Parts" section at the front of the guide for part
details and orders.
6
iNSTALLATiON iNSTRUCTiONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
i Discoaaect electric al POwe[ atthe fuse bO× or c!rcu!t
J
YeS --Follow instructions )n the "Prepare Cabinet
Opening--Existing Utilities section.
NO Follow instructions in the "Prepare Cabinet
Opening--New Utilities" section,
Existing utility hookups
Cable
When removing a previous dishwasher, be sure to avoid
damaging the existing power cord, drain line, and water line
connected to the dishwasher.
If the water line and the cable extend to the locations shown,
proceed to the "install Drain Hose" section. If they do not reach
far enough, follow the instructions in the "Prepare Cabinet
Opening--New Utilities" section.
Prepare And Route The Electrical Supply
What type of electrical
connection will you use?
[
Option A_ Power Cord =
NOTE." A grounded 3 prong outlet is required inside a cabinet
next to the dishwasher cabinet opening.
Drill a 11/2" (3.8 cm) hole in cabinet side or rear. See the
"Product and Cabinet Opening Dimensions" section.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover edges of hole with grommet included with
power cord kit.
See the "Tools and Parts" section at the front of the guide for
part details.
Option B_Direct Wire
Helpful Tip."Wiring the dishwasher will be easier if you route the
cable into the cab}net opening from the right-hand s}de.
Drill a 11/2"(3.8 cm) hole in right-hand cabinet side or rear.
See the "Product and Cabinet Opening Dimensions" section.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover edges of hole with a grommet.
See the "Tools and Parts" section at the front of the guide for
part details.
Route cable from power supply through cabinet hole (cable
must extend to the right front side of cabinet opening). Tape
cable to the floor in area shown. This will prohibit cable from
moving when dishwasher is moved into cabinet opening.
Loading...
+ 18 hidden pages