Karcher K 2200 IB User Manual

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 1

Model K 1800 IB

Model K 2200 IB

Part No. 1.133-121

Part No. 1.133-211

High Pressure Washer Operator Manual

Overview . . . . . . . . . . . . . . . . . . . . . .1

Precautions . . . . . . . . . . . . . . . . . . .1-2

Assembly Instructions . . . . . . . . . . . .3

Operating Instructions . . . . . . . . . . . .4

Using the Accessories . . . . . . . . . . . .5

Working with Detergents . . . . . . . . . . .6

Shut Down and Clean-Up . . . . . . . . . .7

Taking a Break . . . . . . . . . . . . . . . . . .7

Winterizing and Long-Term Storage . .7

Cleaning Tips . . . . . . . . . . . . . . . . .8-9

Optional Cleaning Accessories . . . . . .9

Trouble Shooting . . . . . . . . . . . . .10-11

Specification

Model K 1800 IB

Max. Operating pressure	1800 PSI
Max. Water volume	2.0 GPM

Engine 3.75 HP Briggs & Stratton Sprint

Model K 2200 IB

Max. Operating pressure	2200 PSI
Max. Water volume	2.2 GPM

Engine 6.0 HP Briggs & Stratton Quantum

Manual Part No. 9.139-111

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 2

MODEL K 1800 IB/2200 IB OVERVIEW

NOTE: Engines controls shown may appear different.

9 8

7 6

14

5

10

11

3

4

1

12

2

13

15

1

Never point nozzle at people or animals.

Never drink alcohol or use drugs while operating this equipment.

Never spray electrical connections, electrical outlets or fixtures.

Never add fuel with the engine running or operate where fuel has been spilled.

Never touch hot surfaces or allow accessories to contact hot surfaces.

Never operate in an enclosed space, exhaust fumes are dangerous.

Never operate near utilities with open flames.

Never operate without the water turned on and never use hot water.

IMPORTANT PRECAUTIONS – Read First!

Safety Warnings

When using this product basic precautions should always be followed:

•Read all the instructions before using the product.

•FIRE HAZARD! Do not add fuel with the engine running. Do not operate if fuel has been spilled. Instead move the machine to a different location and avoid creating sparks.

•Operate and fuel machine in a well ventilated area, free of devices featuring an open pilot or flame such as boilers, water heaters, etc.

•High pressure jets can be dangerous

if subject to misuse. The jet must not be directed at persons, animals, electrical devices, or the machine itself.

•Wear safety goggles.

• Do not use acids, solvents, or any other flammable material in this

product. These products can cause physical injuries to the operator and irreversible damage to the machine.

•The machine has hot surfaces which can cause burns. Operate the unit in a safe environment and away from children.

•Do not allow the high pressure hose to come into contact with the muffler guard.

•Do not leave the machine running unattended.

•Learn how to stop the machine and release pressure quickly. Be thoroughly familiar with the controls.

•Stay alert — watch what you are doing.

•Do not operate the product when fatigued or under the influence of alcohol or drugs.

•Do not stand on unstable surfaces. Stand with both feet balanced at all times.

•The Gun Safety Lock PREVENTS the trigger from accidentally being engaged. This safety feature DOES NOT lock trigger in the “ON” position.

Water Supply

(Cold Water Only)

•Water hose must be at least 3/4 inch in diameter.

•Flow rate of water supply must not fall below 2.5 GPM (gallons per minute).

•Flow rate can be determined by running the water for one minute into an empty 5-gallon container.

•The water supply temperature must not exceed 104°F/40°C.

•Never use the pressure washer to draw in water contaminated with solvents, e.g. paint thinners, gasoline, oil, etc.

•Always prevent debris from being drawn into the unit by using a clean water source.

	We strongly recommend that this high pres-
	sure washer not be left running for periods
	of 5 minutes or longer without the trigger
	gun being engaged.
	This Kärcher high pressure washer is
		2
	equipped with thermal protection to extend
	the life of your pressure washer. The thermal
	protector will automatically activate at a pre-
	determined high temperature ejecting hot
	water before resetting. This ensures that the
	pump does not become damaged.

Caution

•Follow the maintenance instructions specified in the manual.

•This machine has been designed for use with cleaning detergent supplied or recommended by the manufacturer. The use of other cleaning detergents may affect the operation of the machine and void the warranty.

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 4

ASSEMBLY INSTRUCTIONS

OPERATING INSTRUCTIONS

NOTE: Engines controls shown may appear different.

Step 1 Slide the handle through the	Step 2 Align the holes of the accessory
accessory rack.	rack to the handle and fasten the four (4) screws.	Step 1 Connect the high pressure hose to the
		unit’s high pressure outlet.

Step 2 Insert the Vario spray wand into the gun. Push in and turn clockwise to lock spray wand in place.

3

Step 3 Check oil level. Oil level should always be between the “FULL” and “ADD” marks on the dipstick. Be sure the machine is level when checking the oil level. (Refer to the engine’s operating manual for seasonal grades.)

Step 4 Insert the detergent tray into one of the slots of your choice and screw in the fastener. Fill with the proper detergent for your cleaning project.

Important! Do not run the engine with a high or low oil level as this can cause engine damage. If you have further questions regarding the engine, please refer to the engine’s operating manual included with the unit.

You are now ready to operate your Kärcher Pressure Washer.

4

Step 3 Connect	garden	Step 5 Trigger the gun to
garden hose to unit’s	water	eliminate trapped air, wait for a steady
water inlet.	water on	flow of water to emerge
		from the spray nozzle.

Step 6 Model K 1800 IB:	K 2200 IB: Slide the throttle
Slide the throttle control to the fast	position. Then move the choke
position. Then push primer ball three	position (only if engine is
times. Wait 3 seconds between each	move the choke to “RUN”.
push.
Note: in cold weather push 5 times

Step 5 Fill gas tank with unleaded gasoline. Do not use leaded gasoline.

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 6

USING THE ACCESSORIES

Vario spray wand

adjust the cleaning pressure. To clean at maximum presto the high pressure setting (+). To apply detergent,

low pressure setting (-).

For high pressure turn wand collar in the plus

(+) direction.

For low pressure turn wand collar in the minus (-) direction.

5	Warning
	TO AVOID SERIOUS INJURY,
	NEVER POINT SPRAY NOZZLE AT
	YOURSELF, OTHER PERSONS
	OR ANIMALS

WORKING WITH DETERGENT

Detergents can only be applied at low pressure (-).

Step 1 Install the Vario spray wand and set the Vario spray wand to the low pressure setting (-) by turning the wand collar. The wand must be set in the low pressure

(-) position to apply detergents.

Step 2 Adjust the filter end of the detergent tube for light (-), or maximum (+) detergent coverage.

Step 3 Fill a container with Kärcher detergent. Place the filter end of detergent suction tube into the container.

Step 4 With the engine running, pull trigger to operate unit: Liquid detergent is drawn into the unit and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface.

For best results see Cleaning Tips on pages 8 & 9 for specific information on how to clean different surfaces.

Always Use Kärcher

Detergents for Best Results.

Kärcher biodegradable detergents are specially formulated to protect the environment and your pressure washer.

The special formula won’t clog the suction 6 tube filter and will protect the internal

parts of the pressure washer for a longer life. For Kärcher Detergents, check your retailer or call:

USA: 1-800-537-4129 www.karcher-usa.com

CAN: 1-800-465-4980 www.karcher.ca

Kärcher detergents

•House Wash

•Deck Wash

Cleaner

Caution

Never use:

•Bleach, Chlorine products and other corrosive chemicals

•Liquids containing solvents

(i.e., paint thinners, gasoline, oils)

•Tri-sodium phosphate products

•Ammonia products

•Acid-based products

These chemicals will harm the unit and will damage the surface being cleaned.

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 8

SHUTTING DOWN & CLEAN-UP

Step 1 Remove	Step 2		Step 4
detergent suction tube	Turn off the	water	Press trigger to
from container and insert	engine.		release water
into one gallon of fresh			pressure.
water. Siphon water at low
pressure for one minute.

7

Step 5 Disconnect the	Step 6 Disconnect the high pressure	the
garden hose from the	high pressure outlet and engage the

TAKING A BREAK... five minutes or more

Step 2 Press trigger	Step 3 Engage gun
to release water pressure.	safety lock.

CLEANING TIPS

Deck Cleaning

(with or without detergent)

Pre-rinse deck and surrounding area with fresh water. If using Kärcher Deck Wash, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. For best results, limit your work area to smaller sections of approximately 25 square feet. Allow Kärcher Deck Wash to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a long sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right. When moving on to a new section of the cleaning surface, be sure to overlap the previous section to eliminate stop marks and ensure a more even cleaning result.

Caution: Do not use rotating nozzle spray wand on wood surface as it may cause damage.

House Siding

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Kärcher House Wash, place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area to sections of approximately 6 feet and always apply detergent from bottom to top). Allow Kärcher House Wash to remain on surface 1-3 minutes. Do not allow detergent to dry on surface, if surface appears to be drying, simply wet down surface with fresh water. If needed, use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 6 inches from the cleaning surface.

Caution: Do not use rotating nozzle spray wand on siding as it may cause damage.

Cement Patios,

Brick and Stone

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Kärcher All Purpose Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. For best results, limit your work area to smaller sections of approximately 25 square feet. Allow Kärcher All Purpose Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right. For removing extremely stubborn stains, use Kärcher Rotating Nozzle Spray Wand.

Cars, Boats & Motorcycles

(with or without detergent)

Pre-rinse vehicle with fresh water. If using

Kärcher Vehicle Wash, place detergent suc- 8 tion tube directly into cleaning solution and

apply to surface at low pressure. For best results, clean one side of vehicle at a time and always apply detergent from bottom to top, do not allow detergent to dry on surface. If needed, use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 6-8 inches from the cleaning surface (distance should increase when rinsing pin-striping or other sensitive surfaces). Always clean from top to bottom and from left to right. For best results, wipe surface dry with a chamois or soft dry cloth.

Caution: Do not use rotating nozzle spray wand on vehicles as it may cause damage.

become kinked.

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 10

CLEANING TIPS - continued

Barbecue Grills, Outdoor Power Equipment & Gardening Tools

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Kärcher All Purpose Cleaner or Degreaser, place detergent suction tube directly into cleaning solution and apply detergent at low pressure. Allow Kärcher detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For removing extremely stubborn dirt, it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action. To remove caked on mud from garbage cans, lawn mower blades, wheel barrels or other non-sensitive metal surfaces, you may

want to use the Kärcher Rotating Nozzle Spray Wand.

9

Caution: Do not use rotating nozzle spray wand on cloth, plastic or other sensitive surfaces as it may cause damage.

Patio & Lawn Furniture

(with or without detergent)

Pre-rinse furniture and surrounding area with fresh water. If using Kärcher All Purpose Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. Allow Kärcher All Purpose Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. If needed use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For best results, clean from top to bottom and from left to right.

Caution: Do not use rotating nozzle spray wand on patio or lawn furniture as it may cause damage.

Recommendations

•Before cleaning any surface an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results.

•If painted surfaces are pealing or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.

OPTIONAL CLEANING ACCESSORIES

Optional cleaning accessories are available to further enhance your cleaning capabilities: See accessories order form for product descriptions and ordering instructions.

• Rotating Wash Brush	• Pipe Drain Cleaner
• Wash Brush	• Floor Washing Tool
• House Washing Wand	• Sandblasting Attachment
• Extension Wand	• Detergent Foamer Attachment
• Rotating Spray Wand	• Water Pumping Kit
• Flexible Spray Wand	• Water Suction Hose
• Underbody Spray Wand	• Extension Hose 25’
• Telescopic Spray Wand

USA: 1-800-537-4129

www.karcher-usa.com

CAN: 1-800-465-4980

www.karcher.ca

TROUBLE SHOOTING

	Symptom	Cause	Solution
	Engine will not	No gasoline.	Fill gas tank.
	start.
		Low oil level.	Add oil.
		Choke is not in correct	Slide choke lever to “CHOKE”
		position.	position.
		Model K 1800 IB:	Model K 1800 IB:
		Engine needs to be primed.	Slide the throttle control to the
			fast position. Then push primer
			ball three times. Wait 3 seconds
			between each push.
			Note: in cold weather push 5 times.
		Engine throttle is not in	Position the throttle to “FAST”.
	For additional	correct position.
	engine problems
		Pressure built up in the	Squeeze the trigger to release the
	refer to the engine
	owners manual.	high pressure washer.	pressure.
					10
	Unit does not reach	Diameter of garden hose is	Replace with a 3/4 inch garden hose.
	high pressure.	too small.
		Water supply is restricted.	Check garden hose for kinks, leaks
			and blockage.
		Not enough inlet water supply.	Open water source full force.
		Water inlet filter is clogged.	Remove filter and rinse out in warm
			water.
		Spray wand is in low	Turn spray wand tip to high pressure
		pressure position.	position.
	Output pressure	Not enough inlet water supply.	Turn water on full force. Check garden
	varies high and low.		hose for kinks, leaks or blockage.
		Pump is sucking air.	Check that hoses and fittings are air
			tight. Turn off machine and purge
			pump by squeezing trigger gun until
			a steady flow of water emerges
			through the nozzle.
		Water inlet filter is clogged.	Remove filter and rinse out in warm
			water.
		Discharge nozzle is	Blow out or remove debris with a
		obstructed.	fine needle.
		Calcified gun, hose or spray	Run distilled vinegar through
		wand.	detergent suction tube.

K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 12

TROUBLE SHOOTING - continued

		Symptom	Cause	Solution
		No detergent.	Detergent suction tube not	Check connection.
			properly connected to
			machine.
			Detergent is too thick.
			Filter on detergent suction
			tube is clogged.
			Damaged or clogged
			detergent suction tube.
			Spray wand is in high
			pressure position.
			Discharge nozzle is
			obstructed.
		Garden hose	Loose fitting.
		connection leaks.
			Missing/worn rubber
		Spray wand leaks.	Spray wand not properly
			attached.
11
			Broken o-ring or plastic
			insert.
		Pump is noisy.	Pump is sucking air.

Water leaks from	Loose fittings.
pump (up to 10
drops per minute	Thermal protection device
is permissible).	has been activated.
	Water seals are damaged
	or worn.
Oil Drip.	Oil seals are damaged
	worn.

USA: 1-800-537-4129

www.karcher-usa.com

CAN: 1-800-465-4980

www.karcher.ca