QUICKSTART
B140R
Warning
These are only brief instructions! Please read and comply with these instructions prior to using or servicing your appliance.
The non-compliance of the operating and safety instructions may lead to damages of the appliance and to dangers for the operator and other persons.
Start up
|
|
|
|
|
|
1 |
A |
|
|
A |
Check if the battery plug is connected to the |
|
|
|
|||
|
|
|
|
|
appliance. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
A |
B |
|
A |
Sit on the driver's seat. |
|
|
|
|
Set main switch to “1”. |
|
|
|
|
|
||
|
|
|
B |
Check battery status. |
|
|
|
|
|
Note |
|
|
|
|
|
The device is equipped with a safety mechanism |
|
|
|
|
|
to prevent total discharge, i.e. when the permissi- |
|
|
|
|
|
ble minimum capacity is reached, then the ma- |
|
|
|
|
|
chine can only be driven and existing lamps can |
|
|
|
|
|
be switched on. In such a case, the battery mon- |
|
|
|
|
|
||
|
|
|
|
itoring symbol on the control console glows red. |
|
|
|
|
|
|
Drive the machine directly to the charging |
|
|
|
|
|
station; avoid any steep gradients in the |
|
|
|
|
|
process. |
3 |
A |
B |
|
A |
Loosen the star handle screws. |
|
|
|
B |
Push the seat back into the desired position. |
|
|
|
|
|||
|
|
|
|
Tighten star handle screws. |
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
A |
B |
C |
A |
Place the detergent bottle into the device. |
|
|
|
|
Close the bottle lid. |
|
|
|
|
|
||
|
|
|
|
Insert the suction hose of the dosaging |
|
|
|
|
|
|
equipment into the bottle. |
|
|
|
|
B |
Open the cover of the fresh water reservoir. |
|
|
|
|
C |
Fill up fresh water (maximum 60 °C) until the |
|
|
|
|
|
lower edge of filling nozzle. |
|
|
|
|
|
Close the cover of the fresh water reservoir. |
|
|
|
|
Model without dosing equipment "Dose" |
|
|
D |
|
|
||
|
|
|
D |
Pour in detergent. |
Close the cover of the fresh water reservoir.
5.964-043.0 03/12
QUICKSTART
Operation
|
|
|
|
|
|
1 |
A |
|
|
Starting the machine |
|
|
|
|
|||
|
|
|
|
A Sit on the seat and set main switch to "1". |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
2 |
A |
B |
C |
Driving |
|
|
|
|
A Set programme switch to step 1 (driving). |
||
|
|
|
|||
|
|
|
B |
Drive forward |
|
|
|
|
|
|
Set the drive direction using the drive |
|
|
|
|
|
direction button at the operator console. |
|
|
|
|
C |
Reverse drive |
|
|
|
|
|
Set the drive direction using the drive |
|
|
|
|
|
direction button at the operator console. |
|
|
|
|
D Determine the driving speed by pressing |
|
|
D |
E |
|
|
the drive pedal. |
|
|
E Stop the machine: Release the drive pedal. |
3
4 A
Cleaning Programs
AScrubbing suction
Wet clean the floor and vacuum up dirt water.
BWet scrubbing
Wet clean the floor and allow the detergent to react.
CVacuuming
Vacuum the wastewater.
DPolishing
Polishing the floor without the application of liquid.
EScrub the floor without applying water (vacuum polishing)
Polish the floor without applying any fluid and suck in the polishing dust.
FManual cleaning
Apply liquid detergent using the wall-ceiling- floor nozzle (optional) and vacuum it again.
Info button
Use the Info button to select the menu items and do the settings.
ATurning the button to the right/left scrolls through the menus forward/ backward. The selected setting gets accepted by pressing the button.
5.964-043.0 03/12