MEMORY CAMERA
*LYT2202-001A-M*
LYT2202-001A-M
Getting Started
GZ-MS240
Basic User Guide
Dear Customers
Thank you for purchasing this JVC product.
Before use, please read the Safety Precautions and Cautions on P.2 and P.25 to ensure safe use of this product.
This product comes with a “Basic User Guide” (this manual) and a “Detailed User Guide”.
Explains the ways of shooting in various situations and the
Detailed User Guide useful features.
■Access the following website on your PC
.
http://manual.jvc.co.jp/index.html/
For Future Reference:
Enter the Model No. (located on the bottom of the camera) and Serial No. (located on the battery pack mount of the camera) below.
Model No.
Serial No.
Information
Copying Playback Recording
Further
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
NOTES:
•The rating plate and safety caution are on the bottom and/or the back of the main unit.
•The serial number plate is on the battery pack mount.
•The rating information and safety caution of the AC adapter are on its upper and lower sides.
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C or incinerate.
Danger of explosion or Risk of fire if the battery is incorrectly replaced.
•Dispose of used battery promptly.
•Keep away from children.
•Do not disassemble and do not dispose of in fire.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material
– special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
.
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups etc.) on top of this unit. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
Do not point the lens directly into the sun. This can cause eye injuries, as well as lead to the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to this unit and to the user.
Carrying or holding this unit by the LCD monitor can result in dropping the unit, or in a malfunction. Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the unit.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to this unit and leaving it on top of the TV is not recommended, as tripping on the cables will cause the unit to fall, resulting in damage.
CAUTION:
The mains plug shall remain readily operable.
•Remove the mains plug immediately if the camcorder functions abnormally.
WARNING:
The battery pack, this unit with battery installed, and the remote control with battery installed should not be exposed to excessive heat such as direct sunlight, fire or the like.
2 |
For more information, refer to the Detailed User Guide |
http://manual.jvc.co.jp/index.html/ |
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water. 6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat. 9. Protect the power cord from being walked on
or pinched particularly at plugs, convenience receptacles, and the
point where they exit
from the apparatus. 10. Only use attachments/
accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
If this symbol is shown, it is only valid in the European Union.
.
Remember that this camcorder is intended for private consumer use only.
Any commercial use without proper permission is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
Trademarks
•Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
•Windows® is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
•Macintosh is a registered trademark of Apple Inc.
•iTunes, iMovie, iPhoto are trademarks of Apple Inc., registered in the U.S. and other countries.
•YouTube and the YouTube logo are trademarks and/or registered trademarks of YouTube LLC.
•Other product and company names included in this instruction manual are trademarks and/or registered trademarks of their respective holders.
CAUTION:
•Please do not pull or bend the AC adapter plug and cable. This may damage the AC adapter.
Make a backup of important recorded data
It is recommended to copy your important recorded data to a DVD or other recording media for storage. JVC will not be responsible for any lost data.
For more information, refer to the Detailed User Guide |
3 |
http://manual.jvc.co.jp/index.html/ |
Index
Safety Precautions ............................ |
2 |
Index ................................................. |
4 |
Verifying the Accessories .................. |
4 |
Names of Parts and Functions .......... |
5 |
Getting Started ........................ |
6 |
Charging the Battery Pack ................ |
6 |
Grip Adjustment ................................ |
7 |
Inserting an SD card ......................... |
8 |
Clock Setting ................................... |
10 |
Recording .............................. |
12 |
Video Recording .............................. |
12 |
Still Image Recording ...................... |
13 |
Playback ................................ |
14 |
Playing Back/Deleting Files on this Unit |
|
......................................................... |
14 |
Playing Back on TV ......................... |
15 |
Copying ................................. |
16 |
Copying Files .................................. |
16 |
Dubbing Files by Connecting to a DVD |
|
Recorder or VCR ............................. |
17 |
Copying to Computer ...................... |
18 |
Further Information ................ |
21 |
Using the Menu ............................... |
21 |
Recordable Time/Number of Images |
|
......................................................... |
22 |
Troubleshooting .............................. |
23 |
Cautions .......................................... |
25 |
Specifications .................................. |
27 |
Learning About Advanced Operations
Use the “Detailed User Guide” on your PC to find out more about the advanced operations.
■ Access the following address on your PC http://manual.jvc.co.jp/index.html/
Verifying the Accessories
AC Adapter |
Battery Pack |
USB Cable |
AV Cable |
|
AP-V30U* |
BN-VG107U |
(Type A - Mini Type B) |
||
|
|
. |
. |
. |
CD-ROM |
Basic User Guide |
Core Filter |
|
(this manual) |
|||
|
|
||
|
|
|
|
|
|
|
.
●SD cards are sold separately.
For details on the types of cards that can be used on this unit, refer to P.8.
*When using the AC adapter overseas, please prepare a commercially available converter plug for the country or region of visit.
4 |
For more information, refer to the Detailed User Guide |
http://manual.jvc.co.jp/index.html/ |
Names of Parts and Functions
1 |
9 0a |
2 |
|
3 |
|
4 |
|
5 |
|
|
AV |
6 78
.
A Lens/Lens Cover
BLight
CStereo Microphone
DLCD Monitor
Turns the power on/off by opening and closing.
ESlider
Selects an image or item.
FOK Button
Confirms the selected image or item.
GOperation Buttons
Functions differently according to the operation.
HMenu (menu) Button ( P.21)
ISpeaker
JACCESS (Access) Lamp
Lights up/blinks during recording or playback.
KPOWER/CHARGE (Power/Charge)
Lamp ( P.6)
L+ (Play) Button
Switches between recording and playback modes.
M/ (Video/Still Image) Button Switches between video and still image modes.
g |
|
|
h |
l |
|
i |
||
j |
m |
|
k |
n |
|
b |
|
|
c |
o |
|
d |
p |
|
e |
q |
|
f |
||
|
NUPLOAD/EXPORT
(Upload/Export to iTunes) Button
Recording Takes videos in YouTube or iTunes format.
Playback Changes the video to YouTube or iTunes format.
O, (Power/Information) Button
Recording Displays the remaining time as well as the battery power during continuous recording.
Playback Displays file information.
Press and hold to turn the power on/off while the LCD monitor is opened.
PAV Terminal ( P.15, P.17)
QZoom/Volume Lever ( P.12, P.14)
RSNAPSHOT (Still Image Recording) Button ( P.13)
SUSB Terminal ( P.20)
TDC Terminal ( P.6)
USTART/STOP (Video Recording)
Button ( P.12)
VLens Cover Switch ( P.12)
WGrip Belt Release Lever
XGrip Belt ( P.7)
YTripod Mounting Hole
ZSD Card Slot ( P.8)
a Battery Release Lever ( P.6)
For more information, refer to the Detailed User Guide |
5 |
http://manual.jvc.co.jp/index.html/ |
Getting Started
Charging the Battery Pack
1 Attach the battery pack.
*The battery pack is not charged at the time of purchase.
2 Connect the DC
terminal.
Cover
•Align the top of the battery with the mark on this unit, and slide in until the battery clicks into place.
■To detach the battery pack
(Base)
.
AC Adapter To AC Outlet (110V to 240V)
Charging Lamp
3 Plug in the power.
Charging Lamp
Charging in progress: Blinks
Charging finished: Goes out
CAUTION
Be sure to use JVC battery packs.
●If you use any other battery packs besides JVC battery packs, safety and performance cannot be guaranteed.
●Charging time: Approx. 1 h 50 m (using supplied battery pack)
*If the battery pack is charged outside the room temperature range of 10°C to 35°C, charging may take a longer time or it may not start.
Attaching the Core Filter to the DC cord
The core filter reduces interference. Connect the end of the cable with the core filter to this unit.
Release the stopper. |
3 cm |
Wind twice |
||
|
|
|
|
|
|
To be connected |
. |
to this unit. |
6 |
For more information, refer to the Detailed User Guide |
http://manual.jvc.co.jp/index.html/ |
Grip Adjustment
1 Pull back the belt 2 Adjust the length 3 Attach the belt
.
Using as a Hand Strap
Remove the strap and loop it around your wrist.
While pressing A, pull B and remove the strap.
Press and hold
.
● When attaching the hand strap, insert C until it clicks into place.
Information
Copying Playback Recording Getting Started
Further
For more information, refer to the Detailed User Guide |
7 |
http://manual.jvc.co.jp/index.html/ |
Inserting an SD card
When a commercially available SD card is inserted, recordings can still be made to the card without stopping when the remaining recording time on the built-in memory runs out.
1 Close the LCD monitor. |
2 Open the cover. |
(Base) |
3 Insert an SD card. |
|
Label |
* Turn o the power of this unit
.before inserting or removing a card.
■To remove the card
Push the card inward once, then pull it out straight.
(Base)
.
NOTE
Operations are confirmed on the following SD cards.
Manufacturer |
Panasonic, TOSHIBA, SanDisk, ATP |
|
|
Video |
Class 4 or higher compatible SDHC card (4 GB to 32 GB) |
|
|
Still Image |
SD card (256 MB to 2 GB), SDHC card (4 GB to 32 GB) |
|
|
●Using cards other than those specified above may result in recording failure or data loss.
8 |
For more information, refer to the Detailed User Guide |
http://manual.jvc.co.jp/index.html/ |
■To use an SD card
Recording and playback can be performed on a card when “REC MEDIA FOR VIDEO” or “REC MEDIA FOR IMAGE” of media settings is set to “SD CARD”.
Display the menu.
Touch
.
Select “MEDIA SETTINGS” and touch .
VIDEO |
|
|
DISPLAY SETTINGS |
|
|
CLOCK ADJUST |
|
|
BASIC SETTINGS |
|
|
CONNECTION SETTINGS |
|
|
MEDIA SETTINGS |
|
|
SET |
? |
QUIT |
Select “REC MEDIA FOR VIDEO” or “REC MEDIA FOR
IMAGE”, and touch .
MEDIA SETTINGS |
|
|
REC MEDIA FOR VIDEO |
|
|
REC MEDIA FOR IMAGE |
|
|
FORMAT BUILT-IN MEM. |
|
|
FORMAT SD CARD |
|
|
ERASE ALL DATA |
|
|
SET |
? |
QUIT |
Select “SD CARD” and touch .
MEDIA SETTINGS
BUILT-IN MEMORY
5& %#4&
SET ? QUIT
■To use SD cards that have been used on other devices
Format (initialize) the card using “FORMAT SD CARD” from media settings.
All data on the card will be deleted when it is formatted. Copy all files on the card to a PC before formatting.
Touch to display the menu.
Select “MEDIA SETTINGS” with the slider and touch .
Select “FORMAT SD CARD” and touch .
MEDIA SETTINGS |
|
|
REC MEDIA FOR VIDEO |
|
|
REC MEDIA FOR IMAGE |
|
|
FORMAT BUILT-IN MEM. |
|
|
FORMAT SD CARD |
|
|
ERASE ALL DATA |
|
|
SET |
? |
QUIT |
Select “FILE” and touch .
FORMAT SD CARD
FILE
FILE + MANAGEMENT NO
SET |
? QUIT |
. |
|
Select “YES” and touch .
After formatting, touch .
Information
Copying Playback Recording Getting Started
Further
For more information, refer to the Detailed User Guide |
9 |
http://manual.jvc.co.jp/index.html/ |
Clock Setting
1 Open the LCD monitor.
AV
●The unit turns on. When the LCD monitor is closed, the unit turns off.
2 |
Select “YES” and touch |
when |
|
“SET DATE/TIME!” is displayed. |
|||
|
Select |
Slider |
|
|
|
SET DATE/TIME! |
|
|
|
YES |
|
|
|
NO |
|
|
|
SET |
|
|
|
OK |
MENU |
.Touch Operation Buttons
●Slide along the slider to select, then touch the operation buttons to set.
3 Set the date and time.
Cursor
|
CLOCK SETTING |
|
|
|
|
|
DATE |
|
|
TIME |
|
|
JAN |
1 |
2009 |
10 |
00 AM |
. |
SET |
|
|
|
QUIT |
|
|
|
|
|
●Use the slider to adjust the year, month, day, hour and minute.
●Touch the operation buttons “&” /
“ ” to move the cursor.
4 |
After setting the date and time, |
touch . |
|
|
|
5 |
Select the region where you live |
and touch . |
|
|
|
●The city name and time difference is displayed.
CLOCK/AREA SETTING
GMT |
JAN. 1. 2009 10:00 AM |
SAVE |
QUIT |
NOTE
●Touch the slider and buttons around the screen with your fingers.
●The slider and buttons do not function if you touch them with your fingernails or with gloves on.
●The displays on the screen do not work even if you touch them.
●“SET DATE/TIME!” is displayed when you turn on this unit after it has not been used for a prolonged period.
Charge this unit for more than 24 hours before setting the clock.
( P.6)
10 For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
■To reset the clock
Set the clock with “CLOCK ADJUST” from the menu.
Display the menu.
Touch
.
Select “CLOCK ADJUST” and touch .
VIDEO
DISPLAY SETTINGS
CLOCK ADJUST
BASIC SETTINGS
CONNECTION SETTINGS
MEDIA SETTINGS
SET |
? QUIT |
Select “CLOCK SETTING” and touch .
CLOCK ADJUST
CLOCK SETTING
AREA SETTING
SET FOR DAYLIGHT SAVING TIME
SET |
? QUIT |
●The subsequent setting operations are the same as steps 3 - 5 on the previous page.
■To change the display language
The language on the display can be changed.
Display the menu.
Touch
.
Select “DISPLAY SETTINGS”
and touch .
VIDEO
AUTO SWITCH REC MEDIA
DISPLAY SETTINGS
CLOCK ADJUST
BASIC SETTINGS
CONNECTION SETTINGS
SET ? QUIT
Select “LANGUAGE” and touch
.
DISPLAY SETTINGS
LANGUAGE
DATE DISPLAY STYLE
MONITOR BRIGHTNESS
LCD BACKLIGHT
SET ? QUIT
Select the desired language and touch .
Touch .
Information
Copying Playback Recording Getting Started
Further
For more information, refer to the Detailed User Guide |
11 |
http://manual.jvc.co.jp/index.html/ |
Recording
Video Recording
You can record without worrying about the setting details by using the auto mode.
Before recording an important scene, it is recommended to conduct a trial recording.
1Open the |
2 Select |
lens cover. |
video mode. |
Press
4 Start recording.
•Press again to stop.
3Check if the recording mode is Auto.
•If the mode is Manual,
touch the button to switch.
•The mode changes between auto and manual with every touch.
Touch
AV
Zooming
(Wide angle) (Telephoto)
Press
.
■Indications during video recording
|
Video Quality |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
Remaining Recording Time |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Record-Standby |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Scene Counter |
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording in Progress |
|
|
|
|
|
|
|
|
|
|
|
|
Recording Media |
||
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
Battery Indicator |
||
. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE
●The estimated recording time of the supplied battery pack is approximately 50 minutes. ( P.22)
12 For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
Reducing Camera Shake (Video Recording)
When the image stabilizer is set, camera shake during recording can be effectively reduced.
|
(White) Image stabilizer |
|
(Green) Image stabilizer |
Touch |
|
|
(White) OFF |
The setting switches with every touch.
.
A Reduces camera shake.
B Reduces camera shake at wide angle effectively. It is also effective for recording while walking.
NOTE
●It is recommended to set the image stabilizer to off when shooting a subject of little movement with the unit on a tripod.
●Complete stabilization may not be possible if camera shake is excessive.
Still Image Recording
1 Select still image mode.
Press
2 Set the focus on the subject.
Press halfway
Lights up in green when focused
3 Take a still image.
Press fully
AV
Lights up during still image recording
■. |
Indications during still image recording |
|
|||||||||||||
|
|
|
Image Size |
Image Quality |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Remaining Number of Shots |
|
832 |
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
||||||
|
|
||||||||||||||
|
Shutter Speed |
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording in Progress |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|||||||||||||
|
Focus |
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording Media |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Battery Indicator |
||||
|
|
|
|
|
|
|
|
|
|
|
|||||
|
. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Information
Copying Playback Recording Getting Started
Further
For more information, refer to the Detailed User Guide |
13 |
http://manual.jvc.co.jp/index.html/ |
Playback
Playing Back/Deleting Files on this Unit
Select and play back the recorded videos or still images from an index screen (thumbnail display). The contents of the media selected in media settings ( P.9) are displayed on the index screen.
1 Select the playback mode.
Press
2 Select video or still image mode.
Press
3 Play back a file.
Select Media being played back
Volume adjustment during video playback
Turn down |
|
Turn up |
the volume |
|
the volume |
|
|
|
|
|
■ To delete unwanted files
Select
8+&'1 2.#;$#%-
8+&'1 2.#;$#%-
|
Touch |
Touch |
||
|
|
•Select YES when the |
||
|
•Touch |
|
to stop. |
|
|
|
|||
|
|
|
|
confirmation message |
■. |
|
|
|
appears and touch . |
To capture a still image during playback |
Pause the playback and press the SNAPSHOT button.
■Usable operation buttons during playback
Display |
During video playback |
During still image playback |
/ |
Playback/pause |
Start/pause slideshow |
|
|
|
|
Stop (returns to thumbnail display) |
Stop (returns to thumbnail display) |
|
|
|
|
Advances to the next video |
Advances to the next still image |
|
|
|
|
Returns to the beginning of the scene |
Returns to the previous still image |
|
|
|
! |
Forward search |
- |
|
|
|
" |
Reverse search |
- |
|
|
|
$ |
Forward slow-motion |
- |
|
|
|
% |
Reverse slow-motion |
- |
|
|
|
14 For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
Playing Back on TV
1 Connect to a TV.
*Refer also to the instruction manual of the TV.
●Press the Power button for more than 2 seconds to turn off this unit.
|
|
Video Input |
|
|
Yellow |
To AV Terminal |
|
|
|
|
Video Input |
|
|
White |
|
|
Audio Input (L) |
AV |
|
Red |
AV Cable |
|
|
|
|
Audio Input (R) |
|
(Provided) |
|
Recording Getting Started
AV
TV
.
2 Connect the AC adapter. ( P.6)
● This unit powers on automatically when the AC adapter is connected.
3 Select the TV input switch.
Playback
4 Play back a file. ( P.14)
■To play back with date/time display
Set “DISPLAY ON TV” in the connection settings menu to “ON”.
Alternatively, set “ON-SCREEN DISPLAY” in the playback menu to “DISPLAY ALL” or “DISPLAY DATE ONLY”.
■When images look unnatural on the TV
Images do not appear on the TV |
● Disconnect the cable and connect again. |
properly. |
● Restart this unit by turning off and on. |
|
|
Images are projected vertically |
Set “VIDEO OUTPUT” in the connection settings |
on the TV. |
menu to “4:3”. |
|
|
Images are projected |
Adjust the TV's screen accordingly. |
horizontally on the TV. |
|
|
|
NOTE
●Please contact the TV manufacturer on questions or problems with setting the TV to the correct mode.
Information
Copying
Further
For more information, refer to the Detailed User Guide |
15 |
http://manual.jvc.co.jp/index.html/ |
Copying
Copying Files
You can create discs or copy the files on this unit by connecting it to various devices.
● Copying files by connecting to a DVD writer is not supported.
Device |
|
|
|
Referen |
|
. |
|
|
ce Page |
||
|
|
. |
|||
|
|
|
|||
|
DVD Recorder |
|
|
P.17 |
|
Dubbing Files by |
3 |
3 |
3 |
||
. |
|
|
|
||
Connecting to a DVD |
VCR |
|
|
|
|
Recorder or VCR |
- |
- |
P.17 |
||
3 |
|||||
|
|||||
|
. |
|
|
|
|
Copying to PC |
- |
3* |
3 |
P.18 |
.
*For details on how to create a disc using a computer, refer to the Detailed User Guide.
16 For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
Dubbing Files by Connecting to a DVD Recorder or VCR
You can dub videos in standard quality by connecting to a DVD recorder or VCR. Refer also to the instruction manual of the TV, DVD recorder, VCR, etc.
1 Connect to a VCR/DVD recorder.
● Press the Power button for more than 2 seconds to turn off this unit.
|
|
|
Video Input |
|
|
|
Yellow |
To AV Terminal |
|
|
|
|
|
|
Video Input |
|
|
|
White |
AV |
|
|
Audio Input (L) |
AV Cable |
|
Red |
|
|
|
|
Audio Input (R) |
|
(Provided) |
|
|
|
|
|
AC Adapter To AC Outlet |
|
|
|
(110V to 240V) |
|
|
|
VCR/DVD Recorder |
AV |
|
|
|
|
|
To DC Terminal |
.
● This unit powers on automatically when the AC adapter is connected.
2 Select the playback mode.
Press
AV
3 Prepare to record.
Preparation on TV and VCR/DVD recorder
● Switch to a compatible external input.
●Insert compatible blank DVD or VHS to dub.
Preparation on this unit
●Set “VIDEO OUTPUT” in the connection settings menu to the aspect ratio (“4:3” or “16:9”) of the connecting TV.
●To include the date during dubbing, set “DISPLAY ON TV” in the connection settings menu to “ON”. Alternatively, set “ON-SCREEN DISPLAY” in the playback menu to “DISPLAY DATE ONLY”.
4 Start recording.
●Start playback on this unit ( P.14) and press the record button on the recorder.
●After playback is complete, stop the recording.
Information
Copying Playback Recording Getting Started
Further
For more information, refer to the Detailed User Guide |
17 |
http://manual.jvc.co.jp/index.html/ |