JVC GZ-HM30U, GZ-HM50U User Manual

0 (0)
EN SP
HD MEMORY CAMERA
LYT2257-001A-M
GZ-HM50U GZ-HM30U
Basic User Guide
Dear Customers
Thank you for purchasing this JVC product. Before use, please read the Safety Precautions and Cautions on P.2 and P.25 to ensure safe use of this product.
Getting StartedRecordingPlaybackCopying
.
A “Basic User Guide” (this manual) and a “Detailed User Guide” are available for this product. For more details on operating this product, please refer to the “Detailed User Guide” at the following website.
o o
For Future Reference:
Enter the Model No. (located on the bottom of the camera) and Serial No. (located on the battery pack mount of the camera) below.
Model No. Serial No.
Detailed User Guide
http://manual.jvc.co.jp/index.html/ You can also access the website from the supplied CD-ROM. (P.19)
Further
Information
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
NOTES:
The rating plate and safety caution are on the
bottom and/or the back of the main unit.
The serial number plate is on the battery pack
mount.
The rating information and safety caution of the
AC adapter are on its upper and lower sides.
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C (212°F) or incinerate. Replace battery with Panasonic, Sanyo, Sony or Maxell CR2025. Danger of explosion or Risk of fire if the battery is incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in fire.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.) No naked flame sources, such as lighted candles, should be placed on the apparatus. When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. The apparatus shall not be exposed to dripping or splashing. Do not use this equipment in a bathroom or places with water. Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups etc.) on top of this unit. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
Do not point the lens directly into the sun. This can cause eye injuries, as well as lead to the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to this unit and to the user. Carrying or holding this unit by the LCD monitor can result in dropping the unit, or in a malfunction. Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the unit.
CAUTION!
Connecting cables (Audio/Video, etc.) to
this unit and leaving it on top of the TV is not recommended, as tripping on the cables will cause
this unit
to fall,
resulting in damage.
CAUTION:
WARNING:
The battery pack, the camcorder with battery installed, and the remote control with battery installed should not be exposed to excessive heat such as direct sunlight, fire or the like.
The mains plug shall remain readily operable.
Remove the mains plug immediately if the camcorder functions abnormally.
.
For more information, refer to the Detailed User Guide
2
http://manual.jvc.co.jp/index.html/
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specifi ed by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
If this symbol is shown, it is only valid in the European Union.
Remember that this unit is intended for private consumer use only.
Any commercial use without proper permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
Trademarks
Make a backup of important recorded data
"AVCHD", "AVCHD" logo, "AVCHD Lite" and "AVCHD Lite" logo are trademarks of Panasonic Corporation and Sony Corporation.
x.v.Color™ is a trademark of Sony Corporation.
HDMI is a trademark of HDMI Licensing, LLC.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Windows® is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
Macintosh is a registered trademark of Apple Inc.
iMovie and iPhoto are trademarks of Apple Inc., registered in the U.S. and other countries.
YouTube™ and the YouTube logo are trademarks and/or registered trademarks of YouTube LLC.
Intel, Intel Core, and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
Eye-Fi is a trademark of Eye-Fi, Inc.
Other product and company names included in this instruction manual are trademarks and/or registered trademarks of their respective holders.
JVC will not be responsible for any lost data. It is recommended to copy your important recorded data to a disc or other recording media for storage.
.
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
3
Contents
Safety Precautions ............................... 2
Verifying the Accessories .................... 4
Names of Parts and Functions ............. 5
IGetting Started ........................... 6
Model Differences ............................... 6
Charging the Battery Pack ................... 6
Grip Adjustment ................................... 7
Using as a Hand Strap ......................... 7
Video Quality ....................................... 7
Inserting an SD Card ........................... 8
Clock Setting ..................................... 10
IRecording ................................. 12
Video Recording ................................ 12
IPlayback ................................... 13
Playing Back/Deleting Files on this Unit
........................................................... 13
Playing Back on TV ............................ 14
ICopying .................................... 16
Copying Files ..................................... 16 Dubbing Files by Connecting to a DVD
Recorder or VCR ............................... 17
Copying to Computer ......................... 18
IFurther Information ................... 21
Operating the Menu ........................... 21
Recordable Time ............................... 22
Troubleshooting ................................. 23
Cautions ............................................ 25
Specifications .................................... 27
.
A “Basic User Guide” (this manual) and a “Detailed User Guide” are available for this product. For more details on operating this product, please refer to the “Detailed User Guide” at the following website.
o o
Detailed User Guide
http://manual.jvc.co.jp/index.html/ You can also access the website from the supplied CD-ROM. (P.19)
Verifying the Accessories
AC Adapter
AC-V11U*
.
CD-ROM
LY37342-025
.
SD cards are sold separately. For details on the types of cards that can be used on this
0
unit, refer to P.8.
* When using the AC adapter overseas, please prepare a commercially available converter
plug for the country or region of visit.
For more information, refer to the Detailed User Guide
4
http://manual.jvc.co.jp/index.html/
Battery Pack BN-VG108U
.
Basic User Guide
(this manual)
.
USB Cable
(Type A - Mini Type B)
QAM1313-001
.
AV Cable
.
Optional Accessories
Component Cable
0
QAM1266-001
Names of Parts and Functions
2
4 5
1
l
cd
g
f
e
i j
h
o
n
m
k
6
7
8
9
0
b
a
3
.
AV Connector (P.15, 17)
K
MENU Button (P.21)
L
HDMI Connector (P.14)
M
USB Connector (P.20)
N
COMPONENT (Component) Connector
O
(P.14)
P
Zoom/Volume Lever / Index (u) (P.12, 13)
i.AUTO (Intelligent Auto) Button (P.12)
Q
DC Connector (P.6)
R
START/STOP Button (Video
S
Recording) (P.12) / d/e (Play/Pause) Button (Video
Playback) (P.13) Strap Lock (P.7)
T
Lens Cover Switch (P.12)
U
Grip Belt (P.7)
V
Tripod Mounting Hole
W
SD Card Slot (P.8)
X
Battery Release Lever (P.6)
Y
http://manual.jvc.co.jp/index.html/
Lens Cover
A
Monaural Microphone
B
LCD Monitor
C
Turns the power on/off by opening and closing.
Speaker
D
ACCESS (Access) Lamp
E
Lights up/blinks during recording or playback.
POWER/CHARGE (Power/Charge)
F
Lamp (P.6)
G
L (Play/Record) Button Switches between recording and playback modes.
UP/< Button
H
UP
< DOWN/> Button
I
DOWN:Scrolls/moves cursor on the
> OK/INFO Button
J
Confirms the selection. / Displays information as follows. Recording:Displays the remaining
Playback:Displays file information
Scrolls/moves cursor on the
:
icons upward Reverse search
:
icons downward Forward search
:
time and battery power.
such as recording date.
For more information, refer to the Detailed User Guide
5
(Base)
To detach the battery pack
Charging finished: Goes out
Charging in progress: Blinks
Charging Lamp
Plug in the power.
To AC Outlet (110 V to 240 V)
AC Adapter
Cover
Connect the DC connector.
Mark
Align the top of the battery with the mark on this unit, and slide in until the battery clicks into place.
The battery pack is not charged at the time of purchase.
Attach the battery pack.

Getting Started

Model Differences

Model Recording Media GZ-HM50 SDHC/SDXC/Built-in Memory (8 GB) GZ-HM30 SDHC/SDXC

Charging the Battery Pack

.
CAUTION
Be sure to use JVC battery packs.
If you use any other battery packs besides JVC battery packs, safety and
0
performance cannot be guaranteed. Charging time: Approx. 2 h 10 m (using supplied battery pack)
0
* The charging time is when the unit is used at 25°C (77°F). If the battery pack is charged
outside the room temperature range of 10°C to 35°C (50°F to 95°F), charging may take a longer time or it may not start. The recordable and playable time may also be shortened under some usage conditions such as at low temperature.
Charging is also possible with a USB cable. (Refer to Detailed User Guide.)
0
For more information, refer to the Detailed User Guide
6
http://manual.jvc.co.jp/index.html/

Grip Adjustment

Close the lever
Adjust the length of the belt
Open the lever on the strap lock
.

Using as a Hand Strap

Adjust the length of the belt and loop it around your wrist.
.

Video Quality

This unit can perform recording in both high and standard definition. By default, it is set to high definition (LS).
To change the setting
o
Press MENU.
A
Press UP/< or DOWN/> to select “VIDEO QUALITY” and press OK/INFO.
B
Press UP/< or DOWN/> to select the video quality.
C
Press OK/INFO. (Setting complete)
D
High Definition
Standard Definition SSW (16:9) SS (4:3)
SEW (16:9) SE (4:3)
* For the approximate video recording time, refer to P.22.
LS (16:9) Higher video quality LE (16:9)
More recording time
Getting StartedRecordingPlaybackCopying
.
Further
Information
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
7

Inserting an SD Card

Tu r n off the power of this unit before inserting or removing a card.
(Base)
Label
Insert an SD card.
Open the cover.Close the LCD monitor.
When the LCD monitor is closed, the unit turns off.
(Base)
Insert a commercially available SD card before recording. (GZ-HM30) When a commercially available SD card is inserted, recordings can still be made to the card without stopping when the remaining recording time on the built-in memory runs out. (GZ-HM50)
* Only for GZ-HM50:
To record to the card, it is necessary to set “REC MEDIA SETTING” to “SD CARD”. (P.9) When no card is available, set “REC MEDIA SETTING” to “BUILT-IN MEMORY” for recording.
.
To remove the card
o
Push the card inward once, then pull it out straight.
.
NOTE
Operations are confirmed on the following SD cards.
Manufacturer Panasonic, TOSHIBA, SanDisk, ATP, Eye-Fi* Video A
Eye-Fi Eye-Fi Connect X2 / Eye-Fi Explore X2 / Eye-Fi Pro X2
*Only the specified models may be used. Refer to the Detailed User Guide for details.
Using SD cards (including SDHC/SDXC cards) other than those specified above
0
may result in recording failure or data loss. To protect the data, do not touch the terminals of the SD card.
0
Eye-Fi manufactures SD memory cards with wireless LAN function.
0
For more information, refer to the Detailed User Guide
8
http://manual.jvc.co.jp/index.html/
Class 4 or higher compatible SDHC card (4 GB to 32 GB) / Class 4 or higher compatible SDXC card (Max. 64 GB)
To select/move cursor towards up/left or down/
REC MEDIA SETTING
SD CARD
FORMAT SD CARD
FORMAT SD CARD
FILE
right, press the button UP/< or DOWN/>.
Getting StartedRecordingPlaybackCopying
To use an SD card
o
(GZ-HM50)
Recording and playback can be performed on a card when “REC MEDIA SETTING” is set to “SD CARD”.
Press MENU.
A
Select “REC MEDIA SETTING”
B
and press OK.
.
Select “SD CARD” and press OK.
C
.
To use SD cards that have been
o
used on other devices
Format (initialize) the card using “FORMAT SD CARD” from media settings.
All data on the card will be deleted when it is formatted. Copy all files on the card to a computer before formatting.
Press MENU.
A
Select “MEDIA SETTINGS” and
B
press OK. Select “FORMAT SD CARD” and
C
press OK.
.
Select “FILE” and press OK.
D
.
Select “YES” and press OK.
E
After formatting, press OK.
F
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
Further
Information
9

Clock Setting

SET DATE /TIME!
YES NO
2011JAN 1 10 00
CLOCK SETTING
DATE TIME
GMT
CLOCK/AREA SETTING
To select/move cursor towards up/left or down/ right, press the button UP/< or DOWN/>.
.
Open the LCD monitor.
1
3
Press UP/< or DOWN/> to adjust the
0
setting value and press OK to confirm it. The cursor moves to the next item.
Repeat this step to input the year, month,
0
day, hour, and minute.
4
.
The unit turns on. When the LCD monitor
0
is closed, the unit turns off.
Select “YES” and press OK when
2
“SET DATE/TIME!” is displayed.
.
The city name and time difference are
0
displayed.
To return to the previous screen
o
Press MENU.
Set the date and time.
.
Press UP/< or DOWN/> to select the region where you live and press OK.
.
10
For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
To reset the clock
CLOCK ADJUST
CLOCK ADJUST
CLOCK SETTING
DISPLAY SETTINGS
LANGUAGE
Set the clock with “CLOCK ADJUST” from the menu.
Press MENU.
A
Select “CLOCK ADJUST” and
B
press OK.
To change the display language
The language on the display can be changed.
Press MENU.
A
Select “DISPLAY SETTINGS”
B
and press OK.
Getting StartedRecordingPlaybackCopying
0
0
.
Select “CLOCK SETTING” and
C
press OK.
.
The subsequent setting operations are the same as steps 3 - 4 on the previous page.
.
Select “LANGUAGE” and press
C
OK.
.
Select the desired language and
D
press OK.
NOTE
“SET DATE/TIME!” is displayed when you turn on this unit after it has not been used for a prolonged period. Charge this unit for more than 24 hours before setting the clock.
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
Further
Information
11
(Telephoto)(Wide angle)
Zooming
Press again to stop.
Start recording.
The mode changes between Intelligent Auto and Manual with every press.
If the mode is H Manual, press the S button to switch.
Check if the recording mode is P Intelligent Auto.
Open the lens cover.
Zoom ratio setting depends on the setting of “VIDEO QUALITY”. (P.27)
0:00:00 [000:22]
Battery Indicator
Recording Media
Recording in Progress
Record-Standby
Remaining Recording Time
Video Quality
Scene Counter
Image Stabilizer

Recording

Video Recording

You can record without worrying about the setting details by using the Intelligent Auto mode. Settings such as exposure and focus will be adjusted automatically to suit the shooting conditions.
*
In case of specific shooting scenes such as backlight (C), night view (B), person (A) etc., its icon is displayed on the screen.
Before recording an important scene, it is recommended to conduct a trial recording.
Indications during video recording
o
0
0
12
.
.
NOTE
The estimated recording time of the supplied battery pack is approximately 40 minutes. (P.22)
Do not remove the battery pack, AC adapter, or SD card when the access lamp is lighted. The recorded data may become unreadable.
For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
2011
Tu r n up the volume
Tu r n down the
volume
Vol ume adjustment
To select/move cursor towards up/left or down/right, press the button UP/< or DOWN/>.
Select the desired video and press [d/e].
Select the playback mode.

Playback

Playing Back/Deleting Files on this Unit

Select and play back the recorded videos from an index screen (thumbnail display). *Only for GZ-HM50: The contents of the media selected in “REC MEDIA SETTING” (P.9) are displayed on the index screen.
.
0
Press L again to return to the recording mode. Videos recorded in high definition and standard definition are displayed on the index
0
screen separately. Set “VIDEO QUALITY” in the recording menu to “LS” or “LE” to view the videos recorded in high definition, or to “SSW”, “SS”, “SEW”, or “SE” to view the videos recorded in standard definition, before selecting the playback mode. (P.7)
Getting StartedRecordingPlaybackCopying
To delete selected files from
o
the index screen
Press MENU, select “DELETE” and
A
press OK. Select “FILE SELECT” and press OK.
B
Usable operation buttons/levers during playback
o
d/e
Zoom u
Zoom T / Vol.+ Increases volume level -
Zoom W / Vol.- Decreases volume level -
UP/< Reverse search Frame-by-frame playback in reverse
DOWN/> Forward search Frame-by-frame playback in forward
During video playback During video pause
Pause Playback
- Stop (returns to thumbnail display)
For more information, refer to the Detailed User Guide
Press UP/< or DOWN/> to select files
C
and press OK. Press MENU, select “DELETE” and
D
press OK to confirm deletion. After deleting is complete, press OK.
E
direction
direction
http://manual.jvc.co.jp/index.html/
Further
Information
13

Playing Back on TV

HDMI Connector Input
TV
HDMI Cable (Optional)
To HDMI
(HDMI mini)
Connector
COMPONENT
AV
Y
CB/PB
CR/PR
Do not connect the yellow plug when using component cable.
TV
Audio Input (R)
Audio Input (L)
Component Video Input
Ye l low
Red
White
Red
Blue
Green
AV Cable (Provided)
To AV Connector
Component Cable (Optional)
To COMPONENT Connector
Connect to a TV.
1
* Refer also to the instruction manual of the TV in use.
Turn off the power.
0
Playing back in HD quality
o
If you are using an HDTV, you can play back in HD quality by connecting to the HDMI connector.
Connecting to the HDMI connector
.
Connecting to the COMPONENT connector
.
NOTE
For questions about the TV or method of connection, contact your TV’s
0
manufacturer. Use a High Speed HDMI Cable (category 2 cable) as the HDMI mini cable.
0
When playing back in HD quality, set “COMPONENT OUTPUT” in the
0
0
14
“CONNECTION SETTINGS” menu to “1080i/720p”. The video is output in standard quality if the setting remains at “480i”.
Component and composite (AV) cannot be output at the same time.
For more information, refer to the Detailed User Guide http://manual.jvc.co.jp/index.html/
Playing back in standard quality
Red
White
Ye l low
TV
Audio Input (R)
Audio Input (L)
Video Input
Video Input
AV Cable (Provided)
To AV Connector
o
If you are using a conventional TV, you can play back in standard quality by connecting to the AV connector.
Connecting to the AV connector
.
Connect the AC adapter.
2
This unit powers on automatically when the AC adapter is connected.
0
Select the TV input switch.
3
Play back a file. (P.13)
4
To play back with date/time display
o
Set “DISPLAY ON TV” in the “CONNECTION SETTINGS” menu to “ON”. Set “ON-SCREEN DISPLAY” in the playback menu to “ON”.
When images look unnatural on the TV
o
Images do not appear on the TV properly.
Images are projected vertically on the TV.
Images are projected horizontally on the TV.
The color of images looks strange.
Disconnect the cable and connect again.
0
Turn off and on this unit again.
0
Set “VIDEO OUTPUT” in the “CONNECTION
0
SETTINGS” menu to “4:3”. Adjust the TV’s screen accordingly.
0
When the video was recorded with “x.v.Color” set
0
to “ON”, change the setting as desired on TV. Adjust the TV’s screen accordingly.
0
Getting StartedRecordingPlaybackCopying
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
Further
Information
15

Copying

Copying Files

You can create discs or copy the files on this unit by connecting it to various devices.
Recordable and playable
:
X
Playable only
:
F
Not applicable
:
Standard Quality HD Quality
Media Selection
Blu-ray Recorder
.
DVD Recorder
.
.
(VHS
Tape)
X
X
.
(DVD Disc)
.
(DVD
Disc)
F *1
F *1
.
(Blu-ray
Disc)
X X
X
.
(Device’s
internal
HDD)
Page
See manual of
recorder.
P.17
VCR
Device
.
X
P.17
Computer
.
*2 *2 *2
X
P.18
*1 Only on AVCHD Lite compatible devices. *2 For details on how to create a disc using a computer, refer to the Detailed User Guide.
NOTE
It is not possible to connect and record to a DVD writer, external Blu-ray drive, or
0
external hard disk.
For more information, refer to the Detailed User Guide
16
http://manual.jvc.co.jp/index.html/
Dubbing Files by Connecting to a DVD
VCR/DVD Recorder
Audio Input (R)
Audio Input (L)
Video Input
Video Input
Red
White
Ye l low
To DC Connector
To AC Outlet (110 V to 240 V)
AC Adapter
AV Cable (Provided)
To AV Connector
Recorder or VCR
You can dub videos in standard quality by connecting to a DVD recorder or VCR. Refer also to the instruction manuals of the TV, DVD recorder, VCR, etc.
Connect to a VCR/DVD recorder.
1
Turn off the power.
0
.
This unit powers on automatically when the AC adapter is connected.
0
Press L (Play/Record) to select the playback mode.
2
.
Prepare to record.
3
Preparation on TV and VCR/DVD recorder
Switch to a compatible external input.
0
Insert a DVD-R or video tape.
0
Preparation on this unit
Set “VIDEO OUTPUT” in the “CONNECTION
0
SETTINGS” menu to the aspect ratio (“4:3” or “16:9”) of the connecting TV. To include the date during dubbing, set “DISPLAY ON TV” in the “CONNECTION
0
SETTINGS” menu to “ON”. Set “ON-SCREEN DISPLAY” in the playback menu to “ON”.
Start recording.
4
Start playback on this unit and press the record button on the recorder.
0
After playback is complete, stop the recording.
0
Getting StartedRecordingPlaybackCopying
Further
Information
For more information, refer to the Detailed User Guide
http://manual.jvc.co.jp/index.html/
17
Loading...
+ 39 hidden pages