Jvc AV-29SX76, AV-29SS26 User Manual

4.3 (4)

SERVICE MANUAL

FLAT COLOUR TELEVISION

YA44920069

AV-29SS26, AV-29SX76

TABLE OF CONTENTS

1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32

BASIC CHASSIS

CW3

No.YA449

2006/9

SPECIFICATION

Items

Dimensions (W × H × D) 81.0 cm × 61.6 cm × 39.4 cm

Mass 44 kg

TV RF System B, G, I, D, K, M

Colour System PAL / SECAM / NTSC 3.58 / NTSC 4.43

Stereo System A2 (B/G) / NICAM (B/G, I, D/K) PB STEREO

Teletext System FLOF (Fastext) WST (World Standard System)

Receiving Frequency

Intermediate Frequency

Colour Sub Carrier

Power Input AC110 V - AC240 V, 50 Hz/60 Hz

Power Consumption 191W (Max) / 129W (Avg)

Picture Tube 29-inch, aspect ratio 4 : 3, flat square type, tinted

High Voltage 30.5 kV +1 kV / -1.5kV

Speaker 6.5 cm × 13 cm, oval type × 2

Audio Power Output 10 W + 10 W (Rated power output)

Aerial Input 75 Ω unbalanced, coaxial

Video / Audio Input-1/2/3

Video / Audio Output

Headphone jack 3.5 mm stereo mini jack × 1 Remote Control Unit RM-C1286 (UM-3/AA/R6 dry cell battery × 2) RM-C1285 (UM-3/AA/R6 dry cell battery × 2)

Component Video

VHF Low 46.25MHz - 140.25MHz (AS0 - S6)

VHF High 147.25MHz - 423.25MHz (S7 - S36)

UHF 431.25MHz - 863.25MHz (S37 - C57)

CATV Mid (X - Z+2, S1 - S10) / Super (S11 - S20) / Hyper (S21 - S41) bands

VIF 38.0MHz (B, G, I, D, K, M)

SIF 32.26 MHz (5.74 MHz: B), 32.15MHz (5.85 MHz: G), 31.45 MHz (6.55 MHz: I)

31.75 MHz (6.5 MHz: D), 32.15MHz (5.85 MHz: K), 33.5MHz (4.5MHz : M)

PAL 4.43 MHz

SECAM 4.40625 MHz / 4.25 MHz

NTSC 3.58 MHz / 4.43 MHz

RCA pin jack × 3

[VIDEO-2]

S-Video

[VIDEO-1]

Y:1V(p-p), positive (negative sync), 75Ω Cb/Cr:0.7V(p-p), 75Ω

Mini-DIN 4 pin × 1 Y: 1V(p-p), positive (negative sync provided), 75Ω

C: 0.286V(p-p) (Burst signal), 75Ω Video 1V(p-p), negative sync, 75Ω, RCA pin jack × 3 Audio 500mV(rms) (-4dBs), high impedance, RCA pin jack × 6 Video 1V(p-p), 75Ω, RCA pin jack × 1 Audio 500mV(rms)(-4dBs), Low impedance, RCA pin jack × 2

AV-29SS26 AV-29SX76/G

Contents

Design and specifications subject to change without notice.

1-2 (No.YA449)

SECTION 1

PRECAUTION

1.1 SAFETY PRECAUTIONS

(1) The design of this product contains special hardware,

many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only.

(2) Alterations of the design or circuitry of the products should

not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom.

(3) Many electrical and mechanical parts in the products have

special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components

having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does

not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards.

(4) Don't short between the LIVE side ground and

ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.

Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken.

(5) If any repair has been made to the chassis, it is

recommended that the B1 setting should be checked or adjusted (See B1 VOLTAGE).

(6) The high voltage applied to the picture tube must conform

with that specified in Service manual. Excessive high voltage can cause an increase in X-Ray emission, arcing and possible component damage, therefore operation under excessive high voltage conditions should be kept to a minimum, or should be prevented. If severe arcing occurs, remove the AC power immediately and determine the cause by visual inspection (incorrect installation, cracked or melted high voltage harness, poor soldering, etc.). To maintain the proper minimum level of soft X-Ray emission, components in the high voltage circuitry including the picture tube must be the exact replacements or alternatives approved by the manufacturer of the complete product.

(7) Do not check high voltage by drawing an arc. Use a high

voltage meter or a high voltage probe with a VTVM. Discharge the picture tube before attempting meter connection, by connecting a clip lead to the ground frame

and connecting the other end of the lead through a 10kΩ

2W resistor to the anode button.

(8) When service is required, observe the original lead dress.

Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.

(9) Isolation Check (Safety for Electrical Shock Hazard)

After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.

a) Dielectric Strength Test

The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade.

b) Leakage Current Check

Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).

Alternate Check Method

Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use

an AC voltmeter having 1000Ω per volt or more sensitivity in the following manner. Connect a 1500Ω 10W resistor paralleled by a 0.15µF AC-type capacitor

between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to

0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).

AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)

0.15 F AC-TYPE

PLACE THIS PROBE

1500 10W

GOOD EARTH GROUND

ON EACH EXPOSED ME TAL PAR T

(No.YA449)1-3

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

2.1 FEATURES

DVD PICTURE MODE

This function can enhance the picture quality of DVD. The screen can be made sharp or soft by this setting.

AUTO SIGNAL DETECT

When input DVD signal to VIDEO-2, detect the input signal and change the input mode to VIDEO-2 automatically.

CINEMA SURROUND

This function can enjoy an enhanced sound for wider audience.

PICTURE MODE

This function can adjust the picture settings automatically. There are BRIGHT, STANDARD and SOFT in the PICTURE MODE.

2.2 MAIN DIFFERENCE LIST

Item AV-29SS26 AV-29SX76/G

OSD Language Eng, Chi, Rus, Mal, Ind Eng, Ara, Fre, Per, Rus

PIP Function NO YES

MAIN PWB SCW-1941A-H2 SCW-1947A-H2

REMOTE CONTROL UNIT RM-C1286 RM-C1285

RETURN +

This function can set a channel frequently view to the Return Channel and you can view that channel at any time with onetouch.

AI ECO SENSOR

This function can adjust TV screen contrast according to the brightness of your room.

MaxxBass

MaxxBass enhances bass sound that cannot be reproduced by normal speakers to be heard by our ears.

2.3 REMOTE CONTROL UNIT

EXIT

RM-C1286

1-4 (No.YA449)

<RM-C1285> <RM-C1286>

2.4 TECHNINAL INFORMATION

2.4.1 MAIN MI-COM (CPU) PIN FUNCTION

Pin name I/O Function

No.

1 VssP2 - GND 65 SVM O Not used 2 VssC4 - GND 66 FbiSo I Flyback input/sandcastle output 3 V1.8C4 I 1.8V (Digital) 67 Hout O Horizontal output 4 V3.3A3 I 3.3V 68 VssComb - GND 5 VrefP_Sdac I 3.3V (Positive) 69 V5Comb I 5V 6 VrefN_Sdac - GND 70 Vin/R2/Pr I PIP R input 7 VrefP_Sdac I 3.3V (Negative) 71 Uin/B2/Pb I PIP B input 8 VrefN_Sdac - GND 72 Yin/G2/Y I PIP G input

9 VrefP_Sdac I 3.3V (Positive) 73 Ysync I Not used 10 XtalIn I 24.576MHz for system clock 74 Yout O Not used 11 XtalOut O 24.576MHz for system clock 75 Uout/INSSW2 I YUV insertion input 12 VssA1 - GND 76 NC O Not used 13 NECK I V-guard input/ I/O switch 77 INSSW3 I YUV insertion input 14 CONT I 1.8V regulator control 78 R3/Pr I Component PR input (Video-2) 15 V5P1 I +5V 79 G3/Y I Component Y input (Video-2) 16 Ph2 - Phase-2 filter 80 B3/Pb I Component PB input (Video-2) 17 Ph1 - Phase-1 filter 81 Gnd3 - GND 18 Gnd1 - GND 82 V5P3 I 5V 19 SecPll - SECAM PLL decoupling 83 BCL I Beam current limiter input 20 Dec8G - Bandgap decoupling 84 BLKIN I Black current input 21 EW O East-West drive output 85 Rout O R output 22 VDRB- O Vertical drive B output 86 Gout O G output 23 VDRA+ O Vertical drive A output 87 Bout O B output 24 Vif1 I Video IF input 1 88 V3.3A1 I 3.3V 25 Vif2 I Video IF input 2 89 RefAdN - GND 26 Vsc - Vertical sawtooth capacitor 90 V3.3RefAdP I 3.3V (Positive) 27 Iref I Reference current input 91 RefAd I 3.3/2V 28 GndIF - GND 92 GndA - GND 29 Sif1 I Sound IF input 1 93 V1.8A I 1.8V 30 Sif2 I Sound IF input 2 94 V3.3A2 I 3.3V 31 AGC O Tuner AGC output 95 VssADC - GND 32 EHT I EHT/overvoltage protection input 96 V1.8ADC I 1.8V 33 Ssif/RefIn/Avl/

RefOut

34 L3 I Audio-L3 input (left signal) 98 PW_LED I POWER LED control 35 R3 I Audio-R3 input (right signal) 99 PW_LED I POWER LED control 36 L-OUT O Audio L output 100 V1.8C2 I 1.8V 37 R-OUT O Audio R output 101 VssC2 - GND 38 DecsDem - Decoupling sound demodulator 102 TIMER - Not used 39 QssO/AmO/

AudeEm 40 Gnd2 - GND 104 VER_PROTECT O X-ray protect 41 PllIf - IF-PLL loop filter 105 S_REDUCE O Sound control 42 SifAgc - AGC sound IF 106 P00/I2SDI1 O Not used 43 IfVo/FmRo/DvbO O Not used 107 POWER O SUB POWER control 44 NC O Not used 108 SCL1 I I2C bus clock 45 V8AudioSwitches I 8V 109 SDA1 I/O I2C bus data 46 AgcSsif - AGC capacitor second sound IF 110 V3.3P I 3.3V 47 V5P2 I 5V 111 ROTATION O Rotation 48 V-OUT O Video output 112 3.58/OTHER O NTSC 3.58 detection 49 L1 I Audio-L1 input 113 A_MUTE O Audio muting 50 R1 I Audio-R1 input 114 4.5/OTHER O NTSC 4.43 detection 51 V3 I Video V3 input 115 PROT I Protect 52 C4 I Not used 116 ECO_IN I ECO sensor level detection 53 Audio2InL I Not used 117 V1.8C1 I 1.8V (Digital) 54 Audio2InR I Not used 118 DecV1V8 I 1.8V 55 V2/Y I Video V2 input 119 KEY_IN I Key scan data 56 L2 I Audio L2 input (Left signal) 120 VDO-DET I Video DET input 57 R2 I Audio R2 input (right signal) 121 VSSC1+P1 - Digital GND 58 Y3/Cvbs I S-Video Y1 input 122 S_V_DET I S-Video DET input 59 C1 I S-Video C1 input 123 P25/PWM4 O GTVA_reset 60 AudioLsL O Audio L output for audio power amplifier 124 V1.8C3 I 1.8V (Digital) 61 AudioLsR O Audio R output for audio power amplifier 125 VssC3 - GND 62 HP-L O Not used 126 P12/Int2 I External interrupt 63 HP-R O Not used 127 SDA0 I/O I2C bus data (for memory) 64 CVBSO/PIP O CVBS / PIP output 128 SCL0 I I2C bus clock (for memory)

O Automatic Volume Levelling/ sound IF input / subcar-

rier reference output / external reference signal input for I signalmixer for DVB operation

O QSS intercarrier output / AM output / deemphasis /

(front-end audio out)

Pin name I/O Function

No.

97 REMOTE I Remote control

103 TIMER - Not used

(No.YA449)1-5

SECTION 3

DISASSEMBLY

3.1 DISASSEMBLY PROCEDURE

3.1.1 REMOVING THE REAR COVER

• Unplug the power cord. (1) Remove the 15 screws [A] as shown in Fig.1. (2) Withdraw the REAR COVER toward you.

CAUTION:

When reinstalling the rear cover, carefully push it inward after inserting the MAIN PWB into the REAR COVER groove.

3.1.2 REMOVING THE CHASSIS (CHASSIS BASE AND

CONTROL BASE)

• Remove the REAR COVER. (1) Slightly raise the both sides of the CHASSIS by hand and

remove the 2 claws [B] under the CHASSIS from the front cabinet as shown in Fig.1.

(2) Withdraw the CHASSIS backward.

(If necessary, take off the wire clamp, connectors etc.)

NOTE:

When conducting a check with power supplied, be sure to confirm that the CRT earth wire is connected to the CRT SOCKET PWB and the MAIN PWB.

3.1.3 REMOVING THE AV BOARD

• Remove the REAR COVER. (1) Remove the 2 screws [C] as shown in Fig.1. (2) When you pull out the AV BOARD in the direction of arrow

[D] as shown in Fig.1, it can be removed.

3.1.4 REMOVING THE CONTROL BASE

• Remove the REAR COVER.

• Remove the CHASSIS. (1) While pushing down the 1 claw [E] as shown in Fig. 2 and

pull out the CONTROL BASE in the direction of arrow [F] as shown in Fig. 2, the control base can be removed. (If necessary, take off the wire, connectors etc.)

3.1.5 REMOVING THE SPEAKER

• Remove the REAR COVER. (1) Remove the 2 screws [G] as shown in Fig.1. (2) Withdraw the SPEAKER backward. (3) Follow the same steps when removing the other hand

SPEAKER.

3.1.6 REMOVING THE FRONT CONTROL PWB(2/2)

• Remove the REAR COVER. (1) Remove the 4 screws [H] as shown in Fig1. (2) Withdraw the FRONT CONTROL PWB(2/2).

3.1.7 CHECKING THE MAIN PW BOARD

• To check the back side of the MAIN PWB. (1) Pull out the CHASSIS and CONTROL BASE. (Refer to the

procedure described in REMOVING THE CHASSIS)

(2) Put the CHASSIS in upright position with the MAIN PWB's

solderside faced to the right. The FBT must be positioned on top. (Viewed from the rear)

(3) Put the CONTROL PWBs in an appropriate position, taking

care not giving tension to the ribbon cables that connect to the MAIN PWB.

CAUTIONS:

• Use insulating materials, if necessary, to avoid possible

electrical contacts between PWBs and expose terminals, etc.

• Before turning on power, make sure that the CRT earth wire

and other connectors are properly connected.

• When repairing, connect the DEG. COIL to the DEG. con-

nector on the MAIN PWB.

3.1.8 WIRE CLAMPING AND CABLE TYING

(1) Be sure to clamp the wire. (2) Never remove the cable tie used for tying the wires

together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.

1-6 (No.YA449)

FRONT CABINET

SPEAKER

[FRONT SIDE]

CONTROL BASE

CHASSIS BASE

Fig.2

CRT SOCKET PWB

MAIN PWB

CLAW

(under side)

AV BOARD

Fig.2

SPEAKER

CONTROL

FRONT CONTROL

PWB(1/2)

BASE

CLAW

(under side)

CHASSIS BASE

BASS PWB

REAR COVER

POWER CORD

FRONT

A CONTROL PWB(2/2)

Fig.1

(No.YA449)1-7

3.2 MEMORY IC REPLACEMENT

• This model uses the memory IC.

Memory IC: IC702 on MAIN PWB

The memory IC memorizes data for correctly operating the video and deflection circuits. When replacing the memory IC, be sure to use the same type IC written with the initial values of data. In other words, use the specific IC listed in "PRINTED WIRING BOARD PARTS LIST". For its mounting location, refer to "ADJUSTMENT LOCATIONS".

3.2.1 MEMORY IC REPLACEMENT PROCEDURE

1. Power off

Switch off the power and disconnect the power plug from the

SERVICE MENU

AC outlet.

2. Replace the memory IC

Be sure to use the memory IC written with the initial setting values.

3. Power on

Connect the power plug to the AC outlet and switch on the

SERVICE MENU

1. IF

3. AUDIO

5. VSM W/B

7. PLUG & PLAY (ON)

1-7 : SELECT DISPLAY : EXIT

2. V/C

4. DEF

6. S TATUS

power.

4. System constant check and setting

******* **** ***** ***** **** **** *** ***

* It must not adjust without signal. (1) Press the [DISPLAY] key and the [PICTURE MODE] key

of the REMOTE CONTROL UNIT simultaneously.

Fig.1

(2) The SERVICE MODE screen of Fig. 1 will be displayed. (3) While the SERVICE MODE is displayed, press the

[DISPLAY] key and the [PICTURE MODE] key simultaneously, and the SYSTEM CONSTANT SET screen of Fig. 2 will be displayed.

(4) Check the setting values of the SYSTEM CONSTANT

SET. If the value is different, select the setting item with the

[MENU /] key, and set the correct value with the [MENU /] key.

(5) Press the [OK] key to memorize the setting value. (6) Press the [DISPLAY] key twice, and return to the normal

screen.

SYSTEM CONSTANT-1

SYSTEM CONSTANT SET 1

SYSTEM COMB TILT SUPER BASS TEXT LANGUAGE

: SEL  : OPE

 

: MULTI :YES :YES :NO :PAT :ERCMI

DISP : EXIT

5. Receiving channel setting

Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.

6. User settings

Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING INSTRUCTIONS and set the items as described.

7. SERVICE MODE setting

Verify what to set in the SERVICE MODE, and set whatever is

SYSTEM CONSTANT-2

SYSTEM CONSTANT SET 2

SOUND BILINGUAL BLUE BACK MUTE COLOUR AUTO ECO SENSOR INTER CARRIER

: SEL  : OPE

 

:STEREO :NO :NO :NO :ECO :NO

DISP : EXIT

necessary (Fig.1). Refer to the SERVICE ADJUSTMENT for setting.

SYSTEM CONSTANT-3

KEY ASSIGNMENT OF REMOTE CONTROL UNIT

SYSTEM CONSTANT SET 3

:YES :NOPICTURE BOOSTER :YESCOMPONENT :NOPIP :YES

:YES

DISP : EXIT

DISPLAY key

MENU key

OK key

PICTURE MODE

key

SURROUND

EXIT

MENU key

S INPUT MAXX BASS

: SEL  : OPE

 

Fig.2

1-8 (No.YA449)

3.2.2 SYSTEM CONSTANT SETTING

Setting item

SYSTEM MULTI ← COMB YES ← TILT YES ← SUPER BASS NO ← TEXT PAT ←

LANGUAGE E/R/C/M/I E/R/A/P/F

SOUND STEREO PB

BILINGUAL NO ← BLUE BACK MUTE NO ←

COLOUR AUTO NO YES

ECO SENSOR ECO ← INTER CARRIER NO ← SURROUND YES ← PICTURE BOOSTER NO ← COMPONENT YES ←

PIP NO YES

S INPUT YES ← MAXX BASS YES ←

AV-29SS26 AV-29SX76/G

Setting value

3.2.3 SETTINGS OF FACTORY SHIPMENT

3.2.3.1 BUTTON OPERATION

Setting item Setting position

POWER Off

CHANNEL PR 1

VOLUME 15

3.2.3.2 REMOTE CONTROL DIRECT OPERATION

Setting item Setting position

CHANNEL PR1

VOLUME 15

PICTURE MODE BRIGHT

DISPLAY Indicated

TV/VIDEO TV

CINEMA SURROUND OFF

3.2.3.3 REMOTE CONTROL MENU OPERATION

(1) PICTURE SETTING

Setting item Setting position

PICTURE MODE BRIGHT

CONTRAST / BRIGHT / SHARP / COLOUR / TINT

WHITE BALANCE COOL

VNR AUTO

(2) SOUND SETTING

Setting item Setting position

STEREO l/ll STEREO SOUND

AI VOLUME OFF

SOUND MODE MUSIC

BALANCE Centre

CINEMA SURROUND OFF

MAXX BASS OFF

Centre

(No.YA449)1-9

(3) FEATURE SETTING

Setting item Setting position

DVD MENU

AUTO SIGNAL DETECT ON

DVD PICTURE MODE OFF

DVD THEATER STATUS OFF

DVD SOUND MODE THEATER

ON TIMER OFF

OFF TIMER OFF

CHILD LOCK OFF

COMPRESS (16:9) OFF

AI ECO SENSOR OFF

(4) INSTALL SETTING

Setting item Setting position

AUTO PROGRAM TV channel automatically set

EDIT/MANUAL PRESET CH only

COLOUR SYSTEM PAL

LANGUAGE ENGLISH

TEXT LANGUAGE GROUP1 [AV-29SS26]

GROUP4 [AV-29SX76/G]

VIDEO-2 SETTING COMPONENT

BLUE BACK ON

BEEP ON

3.2.4 SERVICE MODE SETTING ITEMS

Setting item Setting value

1. IF 1. VCO

2. DELAY POINT

2. V / C

3. AUDIO [Do not adjust]

4. DEF 1. V-SHIFT

5. VSM PRESET 1. BRIGHT

6. STATUS [Dispaly only] ---

1.SCREEN (READ DATA)

2.CUTOFF / CUT OFF THEATER (B/G)

3.WDR (R/G/B)

4.BRIGHT (TV/VDO 1/2/3)

5.CONT. (TV/VDO 1/2/3)

6.COLOUR (TV/VDO 1/2/3)

7.TINT (TV/VDO 1/2/3 /THEATER)

8.SHARP (TV/VDO 1/2/3)

9.Y DELAY (TV/VDO 1/2/3/S-VDO)

10.TINT DVD (TV/VDO/THEATER)

11.AMP T.SHARP (TV/VDO)

12.TWIN CONT (TV/VDO)

1. DCXO ADJ

2. NICAM lower ERRLIM

3. NICAM upper ERRLIM

4. A2 ID THR

5. MENU EQUALIZER

2. V-SLOPE

3. V-SIZE

4. H-CENT

5. H-SIZE

6. TRAPEZ

7. EW-PIN

8. COR-UP

9. COR-LO

10. ANGLE

11. BOW

12. V-S.CR

13. V-LIN

14. V-ZOOM

2. CONT

3. COLOUR

4. SHARP

5. HUE

1. R DRIVE

2. G DRIVE

3. B DRIVE

1-10 (No.YA449)

7. PLUG & PLAY(ON) [Dispaly only] ---

3.3 REPLACEMENT OF CHIP COMPONENT

3.3.1 CAUTIONS

(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.

3.3.2 SOLDERING IRON

(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.

3.3.3 REPLACEMENT STEPS

1. How to remove Chip parts

2. How to install Chip parts

[Resistors, capacitors, etc.]

(1) As shown in the figure, push the part with tweezers and

alternately melt the solder at each end.

(2) Shift with the tweezers and remove the chip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply extra solder to each lead.

SOLDER

[Resistors, capacitors, etc.]

(1) Apply solder to the pattern as indicated in the figure.

(2) Grasp the chip part with tweezers and place it on the

solder. Then heat and melt the solder at both ends of the chip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the

solder.

(3) First solder lead A as indicated in the figure.

(2) As shown in the figure, push the part with tweezers and

alternately melt the solder at each lead. Shift and remove the chip part.

NOTE :

After removing the part, remove remaining solder from the pattern.

(4) Then solder leads B and C.

(No.YA449)1-11

SECTION 4

ADJUSTMENT

4.1 ADJUSTMENT PREPARATION

(1) There are 2 ways of adjusting this TV : One is with the

REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components.

(2) The adjustment using the REMOTE CONTROL UNIT is

made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.

(3) Make sure that connection is correctly made AC to AC

power source.

(4) Turn on the power of the TV and measuring instruments for

warming up for at least 30 minutes before starting adjustments.

(5) If the receive or input signal is not specified, use the most

appropriate signal for adjustment.

(6) Never touch the parts (such as variable resistors,

transformers and condensers) not shown in the adjustment items of this service adjustment.

4.2 PRESET SETTING BEFORE ADJUSTMENT

Unless otherwise specified in the adjustment items, preset the following functions with the REMOTE CONTROL UNIT.

Item Preset value

PICTURE MODE(VSM) BRIGHT

VNR OFF

AI ECO SENSOR OFF

BALANCE Centre

BASS / TREBLE / BALANCE Centre

CINEMA SURROUND OFF

4.3 MEASURING INSTRUMENT AND FIXTURES

(1) DC voltmeter (or digital voltmeter) (2) Oscilloscope (3) HV voltmeter (4) Signal generator

(Pattern generator : PAL/NTSC)

(5) Remote control unit

4.4 ADJUSTMENT ITEMS

 CHECK ITEMS

• B1 VOLTAGE check

• HIGH VOLTAGE check

• IF VCO check

 TUNER / IF CIRCUIT

• DELAY POINT (AGC) adjustment

 FOCUS

• FOCUS adjustment

 DEFLECTION CIRCUIT

• V.SLOPE adjustment

• V.POSITION adjustment

• V.SIZE adjustment

• H.POSITION adjustment

• H.SIZE adjustment

• SIDE PIN adjustment

• TRAPEZIUM adjustment

• V. LINEARITY adjustment

• CORNER adjustment

• H. PARALLEL adjustment

• H.BOW adjustment

 VIDEO CIRCUIT

• WHITE BALANCE adjustment

• SUB BRIGHT adjustment

• SUB CONTRAST adjustment

• SUB COLOUR adjustment

• SUB TINT adjustment

 VSM PRESET SETTING

• VSM PRESET

 PURITY AND CONVERGENCE

• PURITY adjustment

• STATIC CONVERGENCE adjustment

• DYNAMIC CONVERGENCE adjustment

1-12 (No.YA449)

4.5 ADJUSTMENT LOCATION

FRONT CONTROL PWB ASS’Y (1/2) FRONT CONTROL PWB ASS’Y (2/2)

POWER CORD

CN00W

S901

CN002

CNDEG

CN001

DEG COIL

TOPFRONT

SPEAKER (L)

SPEAKER (R)

S804

S803

S801

S802

S805

S806

CN002

J802

CN00S

J801

MAIN PWB ASS’Y

IC702

FRONT

BASS PWB ASS'Y

CRT EARTH

(BRAIDED ASS'Y)

IC701

CN00C

1. 5V

2. SCL0

3. SDA0

4. SCL1

5. SDA1

6. GND

J804J801 J802 J803

GND 5V

TU001

MAIN PWB ASS’Y (CRT SOCKET)

TP-47R

TP-47G

TP-47B

(SOLDER SIDE)

HVT

GND

UPPER : FOCUS

LOWER : SCREEN

TP-E

CN00X

1. B1

2. NC

3. X-RAY2

4. X-RAY1

5. GND

TOP

DEF YOKE

CRT EARTH

(BRAIDED ASS'Y)

(No.YA449)1-13

4.6 BASIC OPERATION OF SERVICE MODE

4.6.1 TOOL OF SERVICE MODE OPERATION

Operate the SERVICE MODE with the REMOTE CONTROL UNIT.

4.6.2 SERVICE MODE ITEMS

With the SERVICE MODE, various adjustments can be made, and they are broadly classified in the following items of settings.

1.IF This mode adjusts the setting values of the IF circuit.

2. V/C This mode adjusts the setting values of the VIDEO circuit.

3.AUDIO This mode adjusts the setting values of the multiplicity AUDIO circuit. [Do not adjust]

4. DEF This mode adjusts the setting values of the DEFLECTION circuit for each aspect mode given below.

5.VSM PRESET This mode adjusts the initial setting values of BRIGHT, STANDARD and SOFT. (VSM : Video Status Memory)

6.STATUS It is no requirement to adjustment. [Do not adjust]

7.PLUG & PLAY (ON) This mode adjusts the setting values of the PIP circuit. [Do not adjust]

4.6.3 BASIC OPERATION IN SERVICE MODE

4.6.3.1 HOW TO ENTER THE SERVICE MODE

(1) Press the [DISPLAY] key and the [PICTURE MODE] key

simultaneously, then enter the SERVICE MODE.

(2) When the main menu is displayed, press any key of the [7]

to [9] key to enter the corresponding sub menu mode.

SERVICE MENU

4.6.3.2 SETTING METHOD

 1.IF

[1. VCO] : It must not adjust without signal

(1) [1] key

Select 1.IF.

(2) [1] key

Select 1.VCO(CW).

SERVICE MENU

1. IF

3. AUDIO

5. VSM W/B

7. PLUG & PLAY (ON)

1-7 : SELECT DISPLAY : EXIT

******* **** ***** ***** **** **** *** ***

2. V/C

4. DEF

6. S TATUS

Fig.1

SERVICE MODE SELECT KEY

 2. V/C, 4. DEF

Check the arrow position between the ABOVE REF. and BELOW REF.

(3) [DISPLAY] key

Return to the SERVICE MODE main manu screen.

(1) [2], [4] key

Select one from 2. V/C, 4. DEF.

(2) [MENU /] key

Select setting items.

(3) [MENU /] key

Set the setting values of the setting items.

 5.VSM W/B

DISPLAY key

MENU key

OK key

PICTURE MODE

key

EXIT

MENU key

(1) [5] key

Select 5.VSM W/B.

(2) [OK] key

Select setting items.

(3) [MENU /] key

Set the setting values of the setting items.

NOTE: This illustration is applicable for RM-C1286. The key assignment of this remote control unit is, however, usable for the other type of remote control units.

Fig.2

1-14 (No.YA449)

4.6.3.3 MEMORIZE THE ADJUSTMENT DATA

When Mnt is completed, press the [OK] key to memorize the adjustment value. If not to do so, the data is not memorized to the memory IC. And if exit the adjustment mode before to memorize the data, the adjustment value which you have changed will be canceled.

4.6.3.4 RELEASE OF SERVICE MODE

After completing the setting, return to the SERVICE MODE, then again press the [DISPLAY] key.

4.6.4 SERVICE MODE FLOW CHART

SERVICE MENU

1. IF

SERVICE MENU

1. IF

3. AUDIO

5. VSM W/B

7. PLUG & PLAY (ON)

1-7 : SELECT DISPLAY : EXIT

******* **** ***** ***** **** **** *** ***

2. V/C

4. DEF

6. STATUS

IF SERVICE MENU

1. VCO

2. DELAY POINT

V/C

1. SCREEN

2. V/C

PAL

HBC

WBC

BRI

VCO (CW)

TOO HIGH ABOVE REFERENCE JUST REFERENCE BELOW REFERENCE TOO LOW

DELAY POINT

AGC TAKEOVER

Setting item

1.SCREEN (READ DATA)

2.CUTOFF / CUT OFF

** ** **

THEATER (B/G)

3.WDR (R/G/B)

4.BRIGHT (TV/VDO 1/2/3)

5.CONT. (TV/VDO 1/2/3)

6.COLOUR (TV/VDO 1/2/3)

7.TINT (TV/VDO 1/2/3 / THEATER)

8.SHARP (TV/VDO 1/2/3)

9.Y DELAY (TV/VDO 1/2/3/ S-VDO)

10.TINT DVD (TV/VDO/ THEATER)

11.AMP T.SHARP (TV/VDO)

12.TWIN CONT (TV/VDO)

*****

MHz

6. STATUS

STATUS

V/C STATUS

ECO EOF NOL VNR

****

ADC ECO =

COSMIC STATUS

*******

** ** ** ** ** ** ** **

5. VSM W/B

VSM PRESET BRIGHT

1. BRIGHT

***

1. BRIGHT

2. CONT

3. COLOUR

4. SHARP

5.HUE

Setting item

1. R-DRIVE

2. G-DRIVE

3. B-DRIVE

3. AUDIO

AUDIO

1. DCXO ADJ. = NOT NICAM

0002

0009

000A

***

******* *******

*******

4. DEF

DEF FULL 50Hz

1. V-SHIFT

***

(**)

Setting item

1. DCXO ADJ

2. NICAM lower ERRLIM

3. NICAM upper ERRLIM

4. A2 ID THR

MENU EQUALIZER

EQUALIZER RF

USER SOUND TURBO THEATER MUSIC NEWS

1. V-SHIFT

2. V-SLOPE

3. V-SIZE

4. H-CENT

5. H-SIZE

6. TRAPEZ

7. EW-PIN

8. COR-UP

EQUALIZER VIDEO EQUALIZER DVD

USER SOUND TURBO THEATER MUSIC NEWS

4 : 3 / 16 : 9

Setting item

Setting value (Hexadecimal)

Setting value

Sereen size

FULL COMPRESS

USER DRAMA THEATER MUSIC

9. COR-LO

10. ANGLE

11. BOW

12. V-S. CR

13. V-LIN

14. V-ZOOM

Fig.3

(No.YA449)1-15

4.7 INITIAL SETTING VALUE OF SERVICE MODE

(1) Adjustment of the SERVICE MODE is made on the basis of the initial setting values:however, the new setting values which set

the screen in its optimum condition may differ from the initial setting value. (2) Do not change the initial setting values of the setting items not listed in "ADJUSTMENT PROCEDURE". (3) The " --- " means adjustment is not possible. (4) " 12.TWIN CONT " is displayed only in the models with PIP function.

[2. V/C] * is variable values for adjustment.

Adjustment item Variable range Initial setting value

PAL SECAM NTSC3.58NTSC4.43VIDEO 2COMPONENT

(V-2)

525i 625i

1. SCREEN BRI 0 ~ 63 32* 32* 32* 32* --- 32* 32*

2. CUT OFF B 0 ~ 63(-32 ~ +31) 37* 37* 37* 37* --- -3* -3*

G 0 ~ 63(-32 ~ +31) 18* 18* 18* 18* --- (-5)* (-5)*

CUT OFF THEATER

3. WDR R 0 ~ 63(-32 ~ +31) 32* 32* 32* 32* --- 0 0

4. BRIGHT RF 0 ~ 63 39* 39* 39* 39* --- --- ---

5. CONT. RF 0 ~ 63 32* 32* 32* 32* --- --- ---

6. COLOUR RF 0 ~ 63(-32 ~ +31) 42* 28* 30* +1 --- --- ---

7. TINT RF 0 ~ 63(-32 ~ +31) --- --- +27* +2 --- --- ---

8. SHARP RF 0 ~ 63 28 28 28 28 --- --- ---

9. Y DELAY RF 0 ~ 15 11 9 12 5 --- --- ---

10. TINT DVD RF 0 ~ 63(-32 ~ +31) 37* -7 +0 +0 --- --- ---

11. AMP T.SHARP

12. TWIN CONT. TWIN (RF) --- -15 -15 -15 -15 --- --- ---

B 0 ~ 63(-32 ~ +31) --- --- --- --- +6 +5 +5

G 0 ~ 63(-32 ~ +31) --- --- --- --- +4 +8 +8

G 0 ~ 63(-32 ~ +31) 32 32 32 32 --- 0 0

B 0 ~ 63(-32 ~ +31) 45* 45* 45* 45* --- 0 0

VIDEO-1(COMPOSITE/S)

VIDEO-2(COMPONENT)

VIDEO-3(COMPOSITE)

VIDEO (-32 ~ +31) (-2) (-2) (-2) (-2) --- (-2) (-2)

VIDEO-1(COMPOSITE/S)

VIDEO-2(COMPONENT)

VIDEO-3(COMPOSITE)

VIDEO (-32 ~ +31) --- --- (+4) (+2) --- --- ---

THEATER (-32 ~ +31) --- --- (+3) (+0) --- --- ---

VIDEO 0 ~ 63 53 53 53 53 --- 15 15

VIDEO 0 ~ 15 9 8 11 10 --- --- ---

S-VIDEO 0 ~ 15 7 7 7 7 --- --- ---

VIDEO (-32 ~ +31) +1 -8 +0 +0 --- +5 +0

THEATER (-32 ~ +31) -2 +0 --- --- --- +3 +3

RF VIDEO 0 ~ 63 0000---00

TWIN (VIDEO) --- --- --- --- --- --- --- ---

(-32 ~ +31) (+1) (+1) (+1) (+1) --- --- ---

(-32 ~ +31) (+1) (+1) (+1) (+1) --- (+2) (+2)

(-32 ~ +31) (+2) (+2) (+2) (+2) --- --- ---

(-32 ~ +31) +6 +3 +3 +2 --- --- ---

(-32 ~ +31) +6 +3 +3 +2 --- (+9) (+5)

(-32 ~ +31) +6 +3 +3 +2 --- --- ---

1-16 (No.YA449)

[3. AUDIO] *This submenu is for display only, no adjustment is required.

Function Item Setting value

AUDIO 1. DC XO ADJ 12H*

2. NICAM LOWER ERR LIM 6FH

3. NICAM UPPER ERR LIM B0H

4. A2 ID THR 00H

Function MODE Item 100Hz 300Hz 1kHz 3kHz 8kHz

MENU EQUALIZER RF SOUND TURBO +11 +8 +4 +7 +9

THEATER +8 +5 -7 +4 +4

MUSIC +10 +6 -5 +4 +10

NEWS -1 -1 +1 -4 -6

USER +0 +0 +0 +0 +0

VIDEO SOUND TURBO +11 +8 +4 +7 +9

THEATER +8 +5 -7 +4 +4

MUSIC +10 +6 -5 +4 +10

NEWS -1 -1 +1 -4 -6

USER +0 +0 +0 +0 +0

DVD THEATER +8 +5 -7 +4 +4

MUSIC +10 +6 -5 +4 +10

DRAMA +2+3+4+1+0

USER +0 +0 +0 +0 +0

[4. DEF]

Adjustment item

1. V-SHIFT 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

2. V-SLOPE 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

3. V-SIZE 0 ~ 63 -32 ~ +31 +30* 0* -4* -2*

4. H-CENT 0 ~ 63 -32 ~ +31 +35* 0* 0* 0*

5. H-SIZE 0 ~ 63 -32 ~ +31 +45* 0* 0* 0*

6. TRAPEZ 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

7. EW-PIN 0 ~ 63 -32 ~ +31 -12* 0* 0* 0*

8. COR-UP 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

9. COR-LO 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

10. ANGLE 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

11. BOW 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

12. V-S.CR 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

13. V-LIN 0 ~ 63 -32 ~ +31 0* 0* 0* 0*

14. V-ZOOM 0 ~ 63 -32 ~ +31 +20 (0) -23* +3*

NOTE: The value with an asterisk * is variable for adjustment. The values in parenthesis ( ) are fixed values.

V-ZOOM DATA can adjust follow data range in case measurement line power on is appeared.

Variable range

4:3 50Hz Others 50Hz 60Hz 50Hz 60Hz

4:3 COMPRESS (16:9)

Initial setting value

(No.YA449)1-17

[5. VSM W/B]

Setting item

1. BRIGHT -16 - 16 0 0 0 -4

2. CONT. -16 - 16 +15 +5 +10 +5

3. COLOUR -16 - 16 0 0 -4 -8

4. SHARP -16 - 16 0 -10 -5 0

5. HUE -16 - 16 0 0 0 -1

Variable

range

BRIGHT SOFT

Setting value

STANDARD THEATER

Setting item

1. R DRIVE -64 - 63 0 +10 0 +9

2. G DRIVE -64 - 63 0 -4 +2 0

3. B DRIVE -64 - 63 0 -12 -10 -27

Variable

range

COOL WARM NORMAL

Setting value

THEATER

1-18 (No.YA449)

4.8 ADJUSTMENT PROCEDURE

4.8.1 CHECK ITEM

Item

B1 VOLTAGE DC voltmeter

Measuring instrument

CN00X connector

1-pin:TP-B1 Remote control unit

HIGH VOLTAGE HV voltmeter

Remote

5-pin:TP-E

[MAIN PWB]

CRT anode

Chassis GND control unit

IF VCO Remote

control unit

Test point Adjustment part Description

(1) Receive any broadcast. (2) Connect a DC voltmeter to 1-pin and 5-pin of CN00X

connector.

(3) Make sure that the voltage is DC134.5V ±2.0V.

(1) Receive any broadcast. (2) Connect the earth clip of HV voltmeter to chassis

GND.

(3) Connect the probe of HV voltmeter to CRT anode.

Make sure that the voltage is

(4)

NOTE:

• Remove the probe before removing the earth clip.

[1.IF]

1.VCO

• Under normal conditions, no adjustment is required.

• Confirmation adjustment. (1) Select 1.IF from the SERVICE MODE. (2) Select <1.VCO> (3) Receive any broadcast.

(4) Check the ←(Arrow) posspition between the ABOVE

REF. and BELOW REF.

Receiving frequency

DC30.5kV +1kV/-1.5kV

IF SERVICE MENU

1. VCO

2. DELAY POINT

VCO (CW)

TOO HIGH ABOVE REFERENCE JUST REFERENCE BELOW REFERENCE

DISPLAY : EXIT1 : SELECT

TOO LOW

. MHz

DISPLAY : EXIT

YELLOW

(No.YA449)1-19

4.8.2 TUNER / IF CIRCUIT

Item

DELAY POINT (AGC)

Measuring instrument

Signal generator

Remote control unit

Setting Item

DELAY POINT (AGC TAKE-OVER)

NTSC3.58

OTHER

4.8.3 FOCUS

Test point Adjustment part Description

[1. IF]

2. DELAY POINT (AGC TAKE-OVER)

(1) Receive a black and white signal (colour off). (2) Select 1. IF. (3) Select <2. DELAY POINT>. (4) Set the setting values of the setting items as shown

bellow table.

(5) Then adjust the [MENU - / +] keys until video noise

Variable range

0 - 127

Initial setting value

disappears.

(6) Turn to other channels and make sure that there are

no irregularities.

Item

FOCUS Signal

Measuring instrument

generator

Test point Adjustment part Description

FOCUS VR [In HVT]

(1) Receive the cross hatch signal. (2) While looking at the screen, adjust the FOCUS VR

to the vertical and horizontal lines will be thinnest and sharpest.

(3) Make sure that the picture is in focus even when the

screen gets darkened.

4.8.4 DEFLECTION CIRCUIT

• The setting (adjustment) using the remote control unit is made on the basis of the initial setting values.

• The setting values which adjust the screen to the optimum condition can be different from the initial setting values.

• When performing deflection circuit adjustment, adjusts PAL signal (fv: 50 Hz) in 4:3 mode and 16:9 mode respectively, and adjust the NTSC signal (fv: 60 Hz) similarly.

NOTE:

Proceed to the following adjustment after having completed the adjustments of SUB BRIGHT and SUB PICTURE.

 COMPRESS: OFF (4:3)

Item

V. SLOPE Signal

Measuring instrument

generator

Test point Adjustment part Description

[4. DEF]

2. V-SLOPE

PAL V. SLOPE

(1) Receive a circle pattern signal of vertical frequency

50Hz (PAL). Remote control unit

(2) Select 4. DEF from the SERVICE MODE. (3) Select <2. V-SLOPE>. (4) Set the initial setting value of <2. V-SLOPE>. (5) Adjust <2. V-SLOPE> to make "A = B". (6) Press the [OK] key to memorize the set values.

Blanking line

NTSC V. SLOPE

(1) Receive a circle pattern signal of vertical frequency

60Hz (NTSC).

(2) Follow the same step 2 to 6 as in PAL V. SLOPE.

1-20 (No.YA449)

Item

Measuring instrument

V. POSITION Signal

generator

Remote control unit

Test point Adjustment part Description

[4. DEF]

1. V-SHIFT

PAL V. POSITION

(1) Receive a circle pattern signal of vertical frequency

50Hz (PAL). (2) Select 4. DEF from the SERVICE MODE. (3) Select <1. V-SHIFT>. (4) Set the initial setting value of <1. V-SHIFT>.

(5) Adjust <1. V-SHIFT> to make "A = B". (6) Press the [OK] key to memorize the set values.

NTSC V. POSITION

(1) Receive a circle pattern signal of vertical frequency

60Hz (NTSC). (2) Follow the same step 2 to 6 as in PAL V. POSITION.

V. SIZE Signal

generator

Remote control unit

Screen

size 92%

H. POSITION Signal

generator

Remote control unit

[4. DEF]

3. V-SIZE

Picture size 100%

[4. DEF]

4. H-CENT

PAL V. SIZE

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <3. V-SIZE>. (4) Set the initial setting value of <3. V-SIZE>. (5) Adjust <3. V-SIZE> to make the vertical screen size

to 92% of the picture size. (6) Press the [OK] key to memorize the set values.

NTSC V. SIZE

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL V. SIZE.

PAL H. POSITION

(1) Receive a PAL circle pattern signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <4. H-CENT>. (4) Set the initial setting value of <4. H-CENT>. (5) Adjust <4. H-CENT> to make "C = D". (6) Press the [OK] key to memorize the set values.

NTSC H. POSITION

(1) Receive a NTSC circle pattern signal. (2) Follow the same step 2 to 6 as in PAL H. POSITION.

(No.YA449)1-21

Item

Measuring instrument

H. SIZE Signal

generator

Remote control unit

Test point Adjustment part Description

[4.DEF]

5. H-SIZE

PAL H. SIZE

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <5. H-SIZE>. (4) Set the initial setting value of <5. H-SIZE>. (5) Adjust <5. H-SIZE> to make the horizontal screen

Screen size 91%

size to 91% of the picture size.

(6) Press the [OK] key to memorize the set values.

NTSC H. SIZE

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL H. SIZE.

Picture size 100%

SIDE PIN Signal

generator

Remote control unit

TRAPEZIUM Signal

generator

Remote control unit

Straight

Parallel

[4. DEF]

7. EW-PIN

[4.DEF]

6. TRAPEZ

PAL SIDE PIN

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <7. EW-PIN>. (4) Set the initial setting value of <7. EW-PIN>. (5) Adjust <7. EW-PIN> so that the first vertical lines at

the left and right edges on the screen are straight.

(6) Press the [OK] key to memorize the set values.

NTSC SIDE PIN

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL SIDE PIN.

PAL TRAPEZIUM

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <6. TRAPEZ>. (4) Set the initial setting value of 6. TRAPEZ. (5) Adjust <6. TRAPEZ> so that the vertical lines at the

left and right edges on the screen are in parallel.

(6) Press the [OK] key to memorize the set values.

NTSC TRAPEZIUM

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL TRAPEZIUM.

1-22 (No.YA449)

Item

Measuring instrument

V.LINEARITY Signal

generator

Remote control unit

Test point Adjustment part Description

[4. DEF]

12. V-S. CR

13. V-LIN

PAL V. LINEARITY

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <12. V-S.CR>. (4) Set the initial setting value of <12. V-S. CR>. (5) Select <13. V-LIN>. (6) Set the initial setting value of <13. V-LIN>.

Top

(7) Adjust <12. V-S. CR> and <13. V-LIN> so that the

spaces of each line on TOP, CENTRE and

BOTTOM become uniform.

Centre

(8) Press the [OK] key to memorize the set values.

NTSC V. LINEARITY

(1) Receive a NTSC crosshatch signal.

Bottom

(2) Follow the same step 2 to 8 as in PAL V-S. CR.

CORNER PIN Signal

generator

Remote control unit

H. PARALLEL Signal

generator

Remote control unit

Straigt

Parallel

[4. DEF]

8. COR-UP

9. COR-LO

[4.DEF]

10. ANGLE

PAL CORNER PIN

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <8. COR-UP>. (4) Set the initial setting value of <8. COR-UP>. (5) Select <9. COR-LO>. (6) Set the initial setting value of <9. COR-LO>. (7) Adjust <8. COR-UP> and <9. COR-LO> so that the

vertical lines at the four corners on the screen are

straight. (8) Press the [OK] key to memorize the set values.

NTSC CORNER PIN

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 8 as in PAL CORNER.

PAL H. PARALLEL

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <10. ANGLE>. (4) Set the initial setting value of <10. ANGLE>. (5) Adjust <10. ANGLE> to optimize the trapezium

distortion at the centre of the screen. (6) Press the [OK] key to memorize the set values.

NTSC H. PARALLEL

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL H.

PARALLEL.

(No.YA449)1-23

Item

Measuring instrument

H. BOW Signal

generator

Remote control unit

 COMPRESS : ON (16:9)

Test point Adjustment part Description

[4.DEF]

11. BOW

PAL H. BOW

(1) Receive a PAL crosshatch signal. (2) Select 4. DEF from the SERVICE MODE. (3) Select <11. BOW>. (4) Set the initial setting value of <11. BOW>.

Straight

(5) Adjust <11. BOW> to optimize the horizontal arc

distortion.

(6) Press the [OK] key to memorize the set values.

NTSC H. BOW

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 6 as in PAL H. BOW.

Item

Measuring instrument

V. SIZE Signal

generator

Remote control unit

Screen

size

Vertical amplitude

V. SLOPE Signal

generator

Remote control unit

Test point Adjustment part Description

[4.DEF]

14. V. ZOOM

3. V-SIZE

PAL V. SIZE

(1) Receive a circle pattern signal of vertical frequency

50Hz (PAL). (2) Set the COMPRESS(16 : 9) to ON. (3) Select 4. DEF from the SERVICE MODE.

Screen size

(4) Set the initial setting value of <14. V. ZOOM>. (5) Select <3. V-SIZE>. (6) Set the initial setting value of <3. V-SIZE>. (7) Adjust <3. V-SIZE> to set the vertical amplitude of

the image to the value shown in the left hand side

Vertical amplitude

list. (8) Press the [OK] key to memorize the set values.

NTSC V. SIZE

(1) Receive a crosshatch signal of vertical frequency

60Hz (NTSC).

AV-29SS26

AV-29SX76/G

305 mm

[4.DEF]

2. V-SLOPE

(2) Follow the same step 2 to 8 as in PAL V. SIZE.

PAL V. SLOPE

(1) Receive a circle pattern signal of vertical frequency

50Hz (PAL). (2) Set the COMPRESS(16 : 9) to ON. (3) Select 4. DEF from the SERVICE MODE. (4) Select <2. V-SLOPE>. (5) Set the initial setting value of <2. V-SLOPE>. (6) Adjust <2. V-SLOPE> to make "A = B".

Blanking line

(7) Press the [OK] key to memorize the set values.

NTSC V. SLOPE

(1) Receive a circle pattern signal of vertical frequency

60Hz (NTSC). (2) Follow the same step 2 to 7 as in PAL V-SLOPE.

1-24 (No.YA449)

Item

Measuring instrument

SIDE PIN Signal

generator

Remote control unit

Test point Adjustment part Description

[4. DEF]

7. EW-PIN

PAL SIDE PIN

(1) Receive a PAL crosshatch signal. (2) Set the COMPRESS(16 : 9) to ON. (3) Select 4. DEF from the SERVICE MODE. (4) Select <7. EW-PIN>.

Straight

(5) Set the initial setting value of <7. EW-PIN>. (6) Adjust <7. EW-PIN> so that the first vertical lines at

the left and right edges on the screen are straight.

(7) Press the [OK] key to memorize the set values.

NTSC SIDE PIN

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 7 as in PAL SIDE PIN.

TRAPEZIUM Signal

generator

Remote control unit

CORNER PIN Signal

generator

Remote control unit

Parallel

Straigt

[4. DEF]

6. TRAPEZ

[4. DEF]

8. COR-UP

9. COR-LO

PAL TRAPEZIUM PIN

(1) Receive a PAL crosshatch signal. (2) Set the COMPRESS(16 : 9) to ON. (3) Select 4. DEF from the SERVICE MODE. (4) Select <6. TRAPEZ>. (5) Set the initial setting value of <6. TRAPEZ>. (6) Adjust <6. TRAPEZ> so that the vertical lines at the

left and right edges on the screen are in parallel.

(7) Press the [OK] key to memorize the set values.

NTSC TRAPEZIUM PIN

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 7 as in PAL TRAPEZIUM.

PAL CORNER PIN

(1) Receive a PAL crosshatch signal. (2) Set the COMPRESS(16 : 9) to ON. (3) Select 4. DEF from the SERVICE MODE. (4) Select <8. COR-UP>. (5) Set the initial setting value of <8. COR-UP>. (6) Select <9. COR-LO>. (7) Set the initial setting value of <9. COR-LO>. (8) Adjust <8. COR-UP> and <9. COR-LO> so that the

vertical lines at the four corners on the screen are straight.

(9) Press the [OK] key to memorize the set values.

NTSC CORNER PIN

(1) Receive a NTSC crosshatch signal. (2) Follow the same step 2 to 9 as in PAL CORNER PIN.

(No.YA449)1-25

 VIDEO - 2 SET: COMPONENT

Item

Measuring instrument

H. POSITION Signal

generator

Remote control unit

4.8.5 VIDEO CIRCUIT

Test point Adjustment part Description

[4. DEF]

4. H-CENT

(1) Receive a PAL circle pattern signal to VIDEO-2

component terminal. (2) Select VIDEO-2 SET from the MENU and set

VIDEO-2 SET to COMPONENT. (3) Select 4. DEF from the SERVICE MODE. (4) Select <4. H-CENT>.

(5) Set the initial setting value of <4. H-CENT>. (6) Adjust <4. H-CENT> to make "C=D". (7) Press the [OK] key to memorize the set values.

Item

WHITE BALANCE (Low light)

WHITE BALANCE (High light)

Measuring instrument

Signal generator

Remote control unit

B CUTOFF (

Signal generator

Remote control unit

Test point Adjustment part Description

REMOTE CONTROL UNIT

12 3

)



789



)

REMOTE CONTROL UNIT

12 3

[2. V/C]

2. CUTOFF (B)

2. CUTOFF (G)

SCREEN VR [In HVT]

G CUTOFF ( )



G CUTOFF (

)

[2. V/C]

3. WDR (R)

3. WDR (G)

3. WDR (B)

COMPOSITE WHITE BALANCE

(1) Receive a PAL black and white signal (colour off). (2) Set the PICTURE MODE to BRIGHT. (3) Select 2. V/C from the SERVICE MODE.

(4) Select <2. CUTOFF> (B) and (G). (5) Set each value to initial setting value with the [4] / [7]

keys and [5] / [8] keys. (6) Turn the SCREEN VR fully counterclockwise, then

slowly turn it clockwise to where a red, blue or green

colour is faintly visible. (7) Use the [4] / [7] and [5] / [8] keys to adjust so that

the other 2 colours appear white. (8) Turn the SCREEN VR to where the single horizontal

line glows faintly. (9) Press the [OK] key to memorize the set values.

COMPONENT WHITE BALANCE

(1) Receive a PAL component black and white signal

(colour off). (2) Select VIDEO-2 SET from the MENU and set

VIDEO-2 SET to COMPONENT. (3) Adjust COMPONENT WHITE BALANCE in the

same way as "COMPOSITE WHITE BALANCE".

(1) Receive a PAL black and white signal (colour off). (2) Set the PICTURE MODE to BRIGHT.

(3) Select 2. V/C from the SERVICE MODE. (4) Select <3. WDR> (R), (G) and (B). (5) Set each value to initial setting value with the [4] to

[9] keys. (6) Use the [4] to [9] keys to produce a white screen. (7) Press the [OK] key to memorize the set values.

1-26 (No.YA449)

) B DRIVE ()

R DRIVE (





)

R DRIVE (

789

G DRIVE ()



B DRIVE (



G DRIVE (

)

Item

Measuring instrument

SUB BRIGHT Remote

control unit

SUB CONTRAST

Remote control unit

SUB COLOUR Remote

control unit

Signal generator

Oscilloscope

Remote control unit

W C

VOLTAGE (W-B)

AV-29SS26

AV-29SX76/G

Test point Adjustment part Description

TP-47B TP-E

[CRT SOCKET PWB]

YGR

Voltage setting

PAL NTSC SECAM

38V

[2. V/C]

4. BRIGHT

[2. V/C]

5. CONT

[2. V/C]

6. COLOUR

[2. V/C]

6. COLOUR

(-)

(A)

(+)

26V 6V

(1) Receive a NTSC broadcast. (2) Set the PICTURE MODE to BRIGHT. (3) Select 2. V/C from the SERVICE MODE. (4) Select <4. BRIGHT>. (5) Set the initial setting value of <4. BRIGHT>. (6) If the brightness is not best with the initial setting value,

make fine adjustment until you get the best brightness.

(7) Press the [OK] key to memorize the set values.

(1) Receive a NTSC broadcast. (2) Set the PICTURE MODE to BRIGHT.

(3) Select 2. V/C from the SERVICE MODE. (4) Select <5. CONT>. (5) Set the initial setting value of <5. CONT>. (6) If the contrast is not best with the initial setting value,

make fine adjustment until you get the best contrast.

(7) Press the [OK] key to memorize the set values.

[Method of adjustment without measuring instrument]

PAL COLOUR

(1) Receive a PAL M broadcast. (2) Set the PICTURE MODE to BRIGHT. (3) Select 2. V/C from the SERVICE MODE. (4) Select <6. COLOUR>. (5) Set the initial setting value of <6. COLOUR>. (6) If the colour is not the best with the initial set value,

make fine adjustment until you get the best colour.

(7) Press the [OK] key to memorize the set values.

SECAM COLOUR

(1) Receive a SECAM broadcast. (2) Follow the same step 2 to 7 as in PAL COLOUR.

NTSC 3.58 COLOUR

(1) Receive a NTSC 3.58MHz broadcast. (2) Follow the same step 2 to 7 as in PAL COLOUR.

NTSC 4.43 COLOUR

• When NTSC 3.58 COLOUR is set, NTSC 4.43 COLOUR will be automatically set.

[Method of adjustment using measuring instrument]

PAL COLOUR

(1) Receive a PAL M colour bar signal (full field colour

bar 75% white). (2) Connect the oscilloscope between TP-47B and TP-E. (3) Set the PICTURE MODE to BRIGHT. (4) Select 2. V/C from the SERVICE MODE. (5) Select <6. COLOUR>. (6) Set the initial setting value of <6. COLOUR>. (7) Adjust the value of (A) to the value in the voltage

table in the left. (8) Press the [OK] key to memorize the set values.

SECAM COLOUR

(1) Receive a SECAM colour bar signal (full field colour

bar 75% white) (2) Follow the same step 2 to 8 as in PAL COLOUR.

NTSC 3.58 COLOUR

(1) Receive a NTSC 3.58MHz broadcast. (2) Follow the same step 2 to 8 as in PAL COLOUR.

NTSC 4.43 COLOUR

• When NTSC 3.58 COLOUR is set, NTSC 4.43

COLOUR will be automatically set.

(No.YA449)1-27

+ 61 hidden pages