JVC AV-32T5SK, AV-32T5BK, AV-28T5SK, AV-28T5BK, AV-32T5SR User Manual

...
0 (0)

AV-32T5SK AV-32T5BK AV-28T5SK AV-28T5BK AV-32T5SR AV-32T5BR AV-28T5SR AV-28T5BR

COLOUR TELEVISION

INSTRUCTIONS

Warning

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If a new mains plug has to be fitted, then follow the instruction given below:

Important

Do not make any connection to the larger terminal which is marked with the letter E or

by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the coloured marking identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

When replacing the fuse, use only a correctly rated approved type and always re-fit the fuse cover.

If in doubt — consult a competent electrician.

How to replace the fuse

Open the fuse compartment with a

blade screwdriver, and replace the fuse.

Fuse

Guidelines for safe operation

This equipment has been designed and manufactured to comply with international safety standards. However, as with any electrical appliance, care must be taken to ensure optimal results and operational safety.

Before attempting to use this equipment, read the operating instructions thoroughly.

Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made in accordance with the manufacturer’s instructions.

If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.

Handle all glass panels or covers with care.

Never operate this equipment if it appears damaged or operates abnormally. Turn the power off, disconnect the main power plug and consult your dealer.

Never remove any affixed panels or covers. Doing so may result in electrical shock.

Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby mode. Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do so. Make special arrangements for infirm or handicapped persons.

Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

Never listen to headphones at high volume. Doing so may damage your hearing.

Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a malfunction or damage.

Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s approved stand or legs, use only the fixtures provided and follow the installation instructions.

Never allow this equipment to be exposed to rain or moisture.

Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may result in a fatal electrical shock.

Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.

2

JVC AV-32T5SK, AV-32T5BK, AV-28T5SK, AV-28T5BK, AV-32T5SR User Manual

How to move the TV

When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful not to trap your hands when putting the TV down.

1

2

3

3

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

Operate only from the power source specified (AC 220 – 240 V, 50 Hz) on the unit.

Avoid damaging the AC plug and power cord.

When you are not using this unit for a long period of time, it is recommended that you disconnect the power cord from the main outlet.

The main power button on the TV does not fully isolate the TV from the mains supply. If you are not going to use this TV for a long period of time, be sure to disconnect the mains plug from the mains outlet.

Avoid improper installation and never put the unit where good ventilation is not possible.

When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture.

Adhere to the minimum distance guidelines shown for safe operation.

Failure to heed the following precautions may result in damage to the TV or remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.

4

CONTENTS

Setting up your TV ...................................

6

Connecting the aerial and video cassette

 

recorder (VCR) .......................................

6

Connecting the power cord to the AC

 

outlet.......................................................

7

Putting the batteries into the remote

 

control.....................................................

7

Initial settings .............................................

7

T-V LINK functions.....................................

9

TV buttons and functions......................

11

Turn the main power on ...........................

11

Turn the TV on from standby mode .........

11

Choose a TV channel ..............................

11

Adjust the volume ....................................

11

Remote control buttons and

 

functions..............................................

12

Turn the TV on or off from standby mode ...

12

Choose a TV channel and watch images

 

from external devices ...........................

13

Adjust the volume ....................................

13

Information function .................................

14

ZOOM function.........................................

14

HYPER SOUND function .........................

15

Return to TV channel instantly.................

16

Operating a JVC brand VCR or DVD

 

player....................................................

16

Teletext function ....................................

17

Basic operation ........................................

17

Using the List Mode .................................

17

Hold..........................................................

18

Sub-page .................................................

18

Reveal......................................................

18

Size..........................................................

18

Index ........................................................

18

Cancel......................................................

19

Using the TV’s menu..............................

20

Basic operation ........................................

20

PICTURE menu.......................................

21

PICTURE MODE .....................................

21

CONTRAST .............................................

21

BRIGHT ...................................................

21

SHARP.....................................................

21

COLOUR..................................................

21

HUE .........................................................

21

COLOUR TEMP.......................................

21

FEATURES..............................................

22

SOUND menu .........................................

24

STEREO / I • II .........................................

24

BASS........................................................

24

TREBLE ...................................................

24

BALANCE ................................................

24

HYPER SOUND.......................................

24

FEATURES menu...................................

25

SLEEP TIMER .........................................

25

BLUE BACK .............................................

25

CHILD LOCK............................................

25

SET UP menu .........................................

27

AUTO PROGRAM....................................

27

EDIT/MANUAL .........................................

27

LANGUAGE .............................................

32

DECODER (EXT-2)..................................

32

EXT SETTING..........................................

33

PICTURE TILT (Only for AV-32T5SK/

 

AV-32T5SR/AV-32T5BR) .....................

35

Additional preparation ..........................

36

Connecting external equipment ...............

36

Troubleshooting ....................................

38

Specifications ........................................

40

5

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and video cassette recorder (VCR)

The connecting cables are not provided.

For further details, refer to the manuals provided with the devices to be connected.

If you are connecting a VCR,

follow A → B → C in the diagram

Aerial

opposite.

 

If you are not connecting a VCR, follow 1.

75-ohm Coaxial Cable

To use the T-V LINK functions, you must have a T-V LINK compatible VCR connected by a SCART cable C to the EXT- 2 terminal on the TV. For details about T-V LINK functions, see “T-V LINK functions” on page 9.

You can watch a video using the VCR without doing C. For details, see your VCR instruction manual.

To connect more equipment, please see “Connecting external equipment” on page 36.

If you connect a decoder to a T-V LINK compatible VCR, set the DECODER (EXT-2) function to ON. For details, see “DECODER (EXT-2)” on page 32. Otherwise, you will not be able to watch scrambled channels.

Rear Panel

Back of the TV

21-pin

75-ohm

SCART Cable

Coaxial

 

Cable

VCR

To Aerial

 

Input

To Aerial

AV IN/OUT Output

Terminal

1 EXT-1 terminal (pages 6, 33, 36) 2 EXT-2 terminal (pages 6, 9, 33, 36) 3 EXT-3 terminal (pages 33, 36)

4 Aerial socket (page 6)

6

Connecting the power cord to the AC outlet

Caution

Operate only from the power source specified (AC 220 – 240 V, 50 Hz) on the unit.

Putting the batteries into the remote control

Use two AA/R6 dry cell batteries.

Insert the batteries from the -end, making sure the +and -polarities are correct.

Setting up your TV

Initial settings

When the TV is first turned on, it goes into the initial settings mode, and you will see the JVC logo. Follow the instructions on the screen display to make the initial settings.

AV

Blue button

MENU

P

TV

OK

P

1Press the main power button on the TV

The power lamp lights red and the JVC logo appears.

Follow the warnings printed on the batteries.

Battery life is about six months to one year, depending on how much you use the remote control.

The batteries we supply are only for setting up and testing your TV, please replace them as soon as you need to.

If the remote control does not work properly, replace the batteries.

Main power

Power lamp

button

 

If the JVC logo does not appear this is because your TV has already been turned on for the first time:

use the “LANGUAGE” and “AUTO PROGRAM” functions to make the initial settings. For details, see “SET UP menu” on page 27.

2Press the abutton

The LANGUAGE menu appears.

LANGUAGE

TV OK

D0002-EK

To receive satellite broadcast you need a satellite tuner.

7

Setting up your TV

3Press the abutton to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears and received TV channels are automatically stored in the programme numbers (PR).

AUTO PROGRAM

CH 24

10%

TV OK

D0004-EN

To cancel the AUTO PROGRAM

function:

Press the bbutton.

After the TV channels have been registered in the programme numbers (PR), the EDIT menu appears

EDIT

 

 

 

 

PR

ID

CH/CC

 

AV

 

CH

36

 

1

BBC1

CH

21

 

2

BBC2

CH

22

 

3

ITV

CH

23

 

4

CH4

CH

24

 

5

CH5

CH

25

 

6

 

CH

26

 

TV

OK

ID

 

MANUAL

 

MOVE

 

 

 

 

 

 

 

INSERT

DELETE

D0038-EK

If you want to, you can now edit the programme numbers (PR) using the EDIT/MANUAL function. For details, see “EDIT/MANUAL” on page 27.

If you do not want to edit programme numbers (PR), go to the next step.

4Press the abutton to display the

T-V LINK menu

T-V LINK

DOWNLOAD TV RECORDING DEVICE

TV

OK EXIT

D0005-EN

If you do not have a T-V LINK compatible VCR connected:

Press the bbutton to exit the T-V LINK menu.

The T-V LINK menu disappears.

If you have a T-V LINK compatible VCR connected to the EXT-2 terminal:

Follow “Downloading the data to VCR” on page 9 to transmit the Programme number (PR) data.

Now, the initial settings are complete, and you can watch the TV

For UK model (AV-32T5SK/AV-32T5BK/AV-28T5SK/ AV-28T5BK):

BBC1, BBC2, ITV, Channel 4 and Channel 5 are automatically set to the programme numbers PR1 to PR5. If the TV doesn't receive one of these TV channels, that programme number (PR) will not be set. Programme number PR6 is not normally set.

For Ireland model (AV-32T5SR/AV-32T5BR/AV-28T5SR/ AV-28T5BR):

If your TV can detect the TV channel name from the TV channel broadcast signal, the TV channel name is assigned to the programme number (PR) to which the TV channel has been set. However, which TV channels are set to which programme numbers (PR) will depend on the area in which you live.

If a TV channel you want to view is not set to a programme number (PR), you can set it using the MANUAL function. For details, see “EDIT/MANUAL” on

page 27.

The AUTO PROGRAM function does not set the programme number PR 0 (AV) for your video cassette recorder. You will need to set this using the MANUAL function.

8

Setting up your TV

In some areas you may get TV reception from more than one transmitter, for example different ITV regions. In this case each TV channel could be set twice. If this happens, the first set of channels will have the stronger signal. If you want to delete the second set of channels, you will have to do it manually (see page 27).

For users in the UK:

If you have any problems setting up your new TV, please call the

Helpline on 0870 330 5000.

For users in the Republic of Ireland:

If you have any problems setting up your new TV, please call the

Helpline on 1890-582500.

Downloading the data to VCR

You can transmit to the latest Programme numbers (PR) data to a VCR with the T-V LINK function.

Caution

This only works when a T-V LINK compatible VCR is connected to the EXT-2 terminal.

This only works when the T-V LINK menu is being displayed.

T-V LINK

DOWNLOAD TV RECORDING DEVICE

TV

OK EXIT

D0005-EN

1Turn on the VCR

2Press the abutton

The data transmission begins.

TV RECORDING DEVICE

TRANSFER. . . . .

D0037-EN

The T-V LINK menu disappears once the data transmission ends.

When the T-V LINK menu is changed over to another menu:

The TV has finished its menu. This new menu is operated from the VCR. See the VCR instruction manual for what to do next.

If “FEATURE NOT AVAILABLE” appears at the T-V LINK menu:

Check the following three items. Then press the 2button to retry data transmission.

Has a T-V LINK compatible VCR been connected to the EXT-2 terminal?

Has the VCR power been turned on?

Does the SCART cable that is connected to the EXT-2 terminal to T- V LINK compatible VCR have all its proper connections?

T-V LINK functions

When you have a T-V LINK compatible VCR connected to the EXT-2 Terminal on the TV, it is easier to set up the VCR and to view videos. T-V LINK uses the following features:

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a JVC video cassette recorder with the T-V LINK logo, or with one of the following logos. However, these VCRs may support some or all of the features described earlier. For details, see your VCR instruction manual.

“Q-LINK” (a trademark of Panasonic Corporation)

“Data Logic” (a trademark of Metz Corporation)

“Easy Link” (a trademark of Phillips Corporation)

“Megalogic” (a trademark of Grundig Corporation)

“SMARTLINK” (a trademark of Sony Corporation).

9

Setting up your TV

Pre-set download

The VCR will automatically download the registered data on the TV channels from the TV. This means you do not need to set up the program channels on your VCR manually. The preset download function automatically begins when the initial setting is complete or whenever you carry out the AUTO PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using your VCR controls.

When “FEATURE NOT AVAILABLE” is displayed:

If “FEATURE NOT AVAILABLE” is displayed, the download was not performed correctly. Before trying to download again, check that:

the VCR power is turned on

the VCR is T-V LINK compatible

the VCR is connected to the EXT-2 terminal

the SCART cable is fully wired.

Direct Rec

“What You See Is What You Record”

You can easily record to VCR the images that you are watching on the TV.

For details, read the manual for your VCR. Use your VCR controls. “VCR IS RECORDING” is displayed.

In the following situations, the VCR will stop recording if the TV is turned off, if the TV channel or input is changed, or if the menu is displayed on the TV:

when recording images from an external device connected to the TV (for example a camcorder)

when recording a TV channel after it has been unscrambled on a decoder

when recording a TV channel by using the TV’s output because the VCR’s own tuner cannot properly receive that channel.

When the VCR is not ready (for example when there is no tape inserted), “NO RECORDING” is displayed.

You cannot carry out Direct Rec using your TV’s control.

Generally, the VCR cannot record a TV channel that it cannot receive properly on its own tuner, even if you can view that TV channel on the TV. However, some VCRs can record a TV channel by using the TV’s output if that channel can be viewed on the TV. For details, see your VCR instruction manual.

10

TV buttons and functions

RL/MONO

EXT-4

P

See the pages in brackets for details.

1 Main power button (pages 7, 11)

2 Power lamp (pages 7, 11)

3 Remote control sensor

4 r(Volume) button (page 11)

5 P pbuttons/ qbuttons (page 11)

6 Headphone jack (mini jack) (page 36)

7 EXT-4 terminal (pages 33, 36)

Turn the main power on

Press the main power button on the TV.

The power lamp lights red and your TV is in standby mode.

To turn the main power off:

Press the main power button again. The power lamp goes off.

Caution

The main power button on the TV does not fully isolate the TV from the AC supply. If you are not going to use the TV for a long period, be sure to disconnect the AC plug from the AC socket.

Turn the TV on from standby mode

Press the P pbuttons to turn the TV on from standby mode

When the TV is turned on, the power lamp dims slightly.

Choose a TV channel

Press the P pbuttons to choose a programme number (PR) or an EXT terminal

Adjust the volume

1Press the r(Volume) button

The volume level indicator appears.

2Press the qbuttons while the volume level indicator is displayed

11

Remote control buttons and functions

1 2 3

4 5 6

7 8 9

0

AV

P

MENU

 

TV

OK

P

 

F.T/L

 

TV

1 Muting button

2 Number buttons

3 cbutton

4 i(hyper sound) button

5 Information button

6 bbutton

7 5buttons

8 #(standby) button

9 Colour buttons

0 abutton - 6buttons

= VCR/DVD/Teletext control button ~ VCR PDVD switch g(text) button

Turn the TV on or off from standby mode

Press the #(standby) button to turn the TV on or off.

When the TV is turned on, the power lamp dims slightly.

The power can be turned on by pressing the bbutton, 6buttons or number buttons.

12

Remote control buttons and functions

Choose a TV channel and watch images from external devices

If the picture is tilted, correct it. See “PICTURE TILT (Only for AV-32T5SK/ AV-32T5BK/AV-32T5SR/AV-32T5BR)” on page 35.

Use the number buttons:

Enter the programme number (PR) of the channel using the number buttons.

Example:

PR 6 press 6

PR 12 press 1and 2

Use the 6 buttons:

Press the 6 buttons to choose the programme number (PR) you want or an EXT terminal.

Use the o button:

Press the obutton to choose an EXT terminal.

TV mode

 

 

 

EXT modes

 

 

 

 

 

 

 

 

 

 

 

Programme

 

 

 

EXT-1

numbers

 

 

 

 

 

 

 

 

 

 

PR 1 – PR 99

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXT-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXT-3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXT-4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You can choose a video input signal from the S-VIDEO signal (Y/C signal) and regular video signal (composite signal). For details, see “y(S- VIDEO input)” on page 33.

If you do not have a clear picture or no colour appears, change the colour system manually. See “COLOUR SYSTEM” on page 22.

If you choose an EXT terminal with no input signal, the EXT terminal number becomes fixed on the screen.

This TV set has a function which can automatically change over the input according to a special signal output from an external device. (The EXT-4 terminal does not support this function.)

To return to a TV channel:

Press the bbutton, the 6buttons or the number buttons.

To use the programme number PR 0 (AV):

When the TV and VCR are connected only by the aerial cable, choosing the programme number PR 0 (AV) allows you to view images from the VCR. Set the VCR RF channel to the programme number PR 0 (AV) manually. For details, see “EDIT/ MANUAL” on page 27.

Pressing the obutton changes the choice as follows:

TV mode

 

 

 

EXT modes

 

 

 

 

PR 0

 

 

EXT-1

Programme

 

 

 

 

 

 

 

 

 

numbers

 

 

 

 

 

 

 

 

PR 1 – PR 99

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXT-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXT-3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

EXT-4

E4

The VCR sends its playback image along the aerial cable as an RF (radio frequency) signal.

Also see your VCR instruction manual.

Adjust the volume

Press the 5buttons to adjust the volume.

The volume indicator appears and the volume changes as you press the 5 buttons.

Muting the sound

Press the l(muting) button to turn off the sound.

Pressing the l(muting) button again restores the previous volume level.

13

Remote control buttons and functions

Information function

You can see the current time or the PR LIST. From the PR LIST, you can choose a channel or EXT terminal.

Press the h(Information) button to

display the information you want to see.

Pressing the h(Information) button changes the display as follows:

PR LIST

 

 

PR

ID

 

AV

 

 

1

BBC1

 

2

 

 

3

 

 

4

 

 

5

 

 

6

 

 

TV

OK

-7

 

+7

D0011-EN

 

 

12 : 00

No indication

Time display:

The current time of the teletext data is displayed.

If the TV has not received a TV channel that has teletext programmes since it was turned on, the time display is blank. To view the current time, choose a TV channel that has teletext programmes.

An incorrect current time is sometimes displayed when watching videos.

PR LIST:

The programme number (PR) and EXT terminal list is displayed.

Pressing the abutton after choosing the programme number (PR) or EXT terminal with the 7buttons will display the chosen programme or EXT terminal.

For programme numbers (PR) for which the CHILD LOCK function is set, the n (CHILD LOCK) mark is displayed. For details see “CHILD LOCK” on page 25.

ZOOM function

You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling) signal, which shows the aspect ratio of the picture, is included in the broadcast signal or the signal from an external device, the TV automatically changes the ZOOM mode to 16:9 ZOOM mode or FULL mode according to the WSS signal.

If a WSS signal is not included, the picture is displayed according to the ZOOM mode set with the 4:3 AUTO ASPECT function.

For details of the 4:3 AUTO ASPECT function, see “4:3 AUTO ASPECT” on page 23.

When the AUTO (WSS) mode does not function correctly due to poor WSS signal

quality or when you want to change the ZOOM mode, press the cbutton and change to another ZOOM mode.

REGULAR:

Use to view a normal picture (4:3 aspect ratio) as this is its original shape.

PANORAMIC:

This stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the screen, without making the picture appear unnatural.

The top and bottom of the picture are slightly cut off.

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen.

14

Remote control buttons and functions

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect ratio) to the full screen.

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect ratio) with subtitles to the full screen.

FULL:

This uniformly stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the wide TV screen.

For 16:9 aspect ratio pictures that have been squeezed into a normal picture (4:3 aspect ratio), use the FULL mode to restore the picture to its original shape.

Choose the ZOOM mode

1Press the cbutton to display the ZOOM menu

ZOOM

AUTO REGULAR PANORAMIC 14:9 ZOOM 16:9 ZOOM

16:9 ZOOM SUBTITLE FULL

TV OK

D0009-EN

2Press the 6buttons to choose a ZOOM mode. Then press the a button

The picture expands and the chosen ZOOM mode is displayed in about 3 seconds.

The ZOOM mode may be automatically changed by the control signal from an external device. When you want to return to the previous ZOOM mode, choose the ZOOM mode again.

Adjusting the visible area of the picture

If subtitles or the top (or bottom) of the picture are cut off, you can adjust the visible area of the picture manually.

1Press the cbutton

The ZOOM menu appears.

2Press the abutton to display the

ZOOM mode indicator

The indicator appears.

16 : 9 ZOOM

D0010-EN

3While it is displayed, press the 6 buttons to change the position of the picture

You cannot adjust the visible area in REGULAR or FULL mode.

The visible area adjustment is saved even after the TV channel is changed.

However, it is cancelled if you do any of the following:

turn the power off/on

change the ZOOM mode

press the g(Text) button

switch the TV between TV mode and EXT mode.

HYPER SOUND function

You can enjoy sounds with a wider ambience.

Press the /(hyper sound) button to turn the HYPER SOUND function on or off

The HYPER SOUND function does not work properly with mono sound.

The HYPER SOUND function can also be turned on or off by using the SOUND menu. For details, see “HYPER SOUND” on page 24.

15

Remote control buttons and functions

Notes for Ireland model (AV-32T5SR/AV-32T5BR/AV-28T5SR/ AV-28T5BR)

-The HYPER SOUND function works only for the audio signal output from TV channels. It cannot work for the audio signal input from EXT sources.

-The HYPER SOUND function affects the audio signal output from the EXT-1 and EXT-2 terminals. If you want to output the normal audio signal from the EXT terminals, turn the HYPER SOUND function off.

Return to TV channel instantly

You can return to a TV channel instantly.

Press the bbutton

The TV returns to the TV mode and a TV channel appears.

Operating a JVC brand VCR or DVD player

These buttons will operate a JVC brand VCR or DVD player. Pressing a button that looks the same as the device’s original remote control button has the same effect as the original remote control.

1Set the VCR PDVD switch to the

VCR or DVD position.

VCR:

When you are using a VCR, set the switch to the VCR position.

DVD:

When you are using a DVD player, set the switch to the DVD position.

P(text):

When you are viewing teletext programmes, set the switch to the P(text) position.

2Press the VCR/DVD Control Button to control your VCR or DVD player

If your device is not made by JVC, these buttons will not work.

Even if your device is made by JVC, some of these buttons may not work, depending on the device you are using.

You can use the pbuttons to choose a TV channel the VCR will receive, or choose the chapter the DVD player plays back.

Some models of DVD player use the pbuttons for both operating the fast forward/backward functions and for choosing the chapter. In this case, the 253buttons do not work.

16

Teletext function

0

AV

P

MENU

 

TV

OK

P

 

F.T/L

 

Basic operation

1Choose a TV channel with a teletext broadcast

2Set the VCR PDVD switch to the g(Text) position

3Press g(Text) button to display the teletext

Pressing g(Text) button changes the mode as follows:

TEXT ---

TEXT ---

TV mode

Text mode

4Choose a teletext page by pressing the p pbuttons, number buttons or colour buttons

To return to the TV mode:

Press the bbutton or g(Text) button.

If you have trouble receiving teletext broadcasts, consult your local dealer or the teletext station.

The ZOOM function will not work in Text mode.

You cannot operate menus when viewing a teletext programme.

The last teletext page displayed is memorised. The last teletext page is cleared if you do any of the following:

Turn the power off

Change the channel

Switch the TV input

Press the bbutton.

Using the List Mode

You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons.

To store the page numbers:

1Press Bbutton to go into the

List mode

The page numbers you have stored are displayed at the bottom of the screen.

2Press a colour button to choose a position. Then press the number buttons to enter the page number

3Press and hold down the A(Store) button

The four page numbers blink white to show that they are stored in memory.

17

Teletext function

To call up a stored page:

1Press the Bbutton to enter the

List mode

2Press a colour button having a stored page

To exit the List mode:

Press the Bbutton again.

Reveal

Some teletext pages include hidden text (such as answers to a quiz).

You can display the hidden text.

Each time you press the E(Reveal) button, text is hidden or revealed

Hold

You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being received.

Press the C(Hold) button

Hold indication

D0040

To cancel the Hold function:

Press C(Hold) button again.

Sub-page

Some teletext pages include sub-pages that are automatically displayed.

You can hold any sub-page, or view it at any time.

1Press the D(Sub-page) button to operate the sub-page function

2Press the number buttons to enter a sub-page number

Example:

3rd sub-page press o, o, oand 3.

To cancel the sub-page function:

Press the D(Sub-page) button again.

D0041

Size

You can double the height of the teletext display.

Press the F(Size) button

D0042

Index

You can return to the index page instantly.

Press the G(Index) button

Returns to page 100 or a previously specified page.

18

Teletext function

Cancel

You can search for a teletext page while watching TV.

1Press the number button to enter a page number, or press a colour button

The TV searches for a teletext page.

2Press H(Cancel) button

The TV programme appears.

3Press H(Cancel) button to return to a teletext page when the page number is on the screen

The TV mode cannot be resumed by pressing the H(Cancel) button. To return to the TV mode press b.

19

Using the TV’s menu

This TV has a number of functions you can operate using menus. To fully utilize all your TV’s functions, you need to understand the basic menu operating techniques fully.

AV

Blue button

MENU

P

TV

OK

Basic operation

1Press the abutton to display the

MENU (main menu)

MENU

PICTURE

SOUND

FEATURES

SET UP

TV OK

D0060-EN

2Press the 6buttons to choose a menu title, and press the abutton

The menu appears.

To return to the previous menu:

Press the h(information) button.

To exit a menu instantly:

Press the bbutton.

3Press the 6buttons to choose a function

For details of the functions in the menus, see the following pages.

4Press the 5buttons to choose the setting of that function

If you want to operate a function which appears only with its name, follow the descriptions of that function on the following pages.

The display appearing at the bottom of a menu shows you a button on the remote control that you can use when you operate a chosen function.

 

D0053

TV

OK

bbutton abutton

5Press the abutton to complete the setting

The menu disappears.

When watching the television with the NTSC system, the menus are displayed at about half their normal vertical size.

20

PICTURE menu

PICTURE

 

 

PICTURE MODE

SOFT

 

CONTRAST

 

 

BRIGHT

 

 

SHARP

 

 

COLOUR

 

 

HUE

 

 

COLOUR TEMP.

NORMAL

 

FEATURES

 

 

TV

OK

RESET

 

 

D0014-EN

 

While the PICTURE menu is displayed, pressing the blue button will set the CONTRAST, BRIGHT, SHARP, COLOUR, HUE settings to their default settings.

PICTURE MODE

You can choose one of three PICTURE MODEs to adjust the picture settings automatically.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustment.

SOFT:

Softens contrast and sharpness.

CONTRAST

You can adjust the picture contrast.

2: lower

3: higher

BRIGHT

You can adjust the picture brightness.

2: darker

3: brighter

SHARP

You can adjust the picture sharpness.

2: softer

3: sharper

COLOUR

You can adjust the picture colour.

2: lighter

3: deeper

HUE

You can adjust the picture tint.

2: reddish

3: greenish

You can change the HUE setting (picture hue) when the colour system is NTSC 3.58, or NTSC 4.43.

COLOUR TEMP.

You can select one of three COLOUR TEMP. modes (three tones of white) to adjust the white balance of the picture. Since white is the colour which is used as a reference for all the other colours, changing the COLOUR TEMP. mode affects the appearance of all the other colours on the screen.

COOL:

A bluish white. Using this mode when watching bright pictures allows you to enjoy a more vivid and bright picture.

NORMAL:

The normal white colour.

WARM:

A reddish white. Using this mode when watching films allows you to enjoy colours that are characteristic of films.

21

PICTURE menu

FEATURES

Choose FEATURES and press the aor 3 button to display the sub-menu.

FEATURES

 

AUTO VNR

MIN

 

COLOUR SYSTEM

 

 

4:3 AUTO ASPECT

 

TV

OK

 

D1015-EN

AUTO VNR

VNR Stands for “video noise reduction”.

AUTO:

This mode reduces any “noise” (interference or snowing) in the current picture. The function also adjusts the optimum sharpness of the picture (SHARP).

OFF:

The AUTO VNR function is cancelled. If you set the mode to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the mode to OFF. However, any noise remaining in the original picture may be emphasized.

MIN:

This mode reduces any noise irrespective of the state of the picture. If you set the mode to AUTO but feel that the sharpness of the original picture has not been reproduced, change the mode MIN. However, any noise remaining in the original picture may be emphasized a little. And this may reduce the sharpness of the picture a little.

MAX:

This mode always reduces any noise as much as possible, irrespective of the state of the picture. When you set the mode to AUTO but still notice some noise, change the mode to MAX. However, this may reduce the sharpness of the picture.

COLOUR SYSTEM

The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually.

1Choose COLOUR SYSTEM. Then press the aor 3button

The sub-menu of the COLOUR SYSTEM function appears.

COLOUR SYSTEM

PAL

TV OK

D0016-EN

2Press the 5buttons to choose the appropriate colour system. Then press the abutton

PAL:

PAL system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43:

NTSC 4.43 MHz system

AUTO:

This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or an EXT terminal.

The AUTO function may not work properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually.

When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3.58 or NTSC 4.43.

22

PICTURE menu

4:3 AUTO ASPECT

You can choose one of three ZOOM modes,

REGULAR, PANORAMIC or 14:9 ZOOM,

as the ZOOM mode for the normal picture

(4:3 aspect ratio).

1

Choose 4:3 AUTO ASPECT then

 

press the abutton

 

4:3 AUTO ASPECT

 

 

PANORAMIC

 

 

REGULAR

 

 

14:9 ZOOM

 

TV

OK

 

D0017-EN

2

Press the 6buttons to choose a

 

ZOOM mode

23

SOUND menu

SOUND

 

STEREO/

 

 

BASS

 

 

TREBLE

 

 

BALANCE

 

 

HYPER SOUND

OFF

TV

OK

 

D0019-EN

STEREO / I • II

When you are viewing a bilingual broadcast programme, you can choose the sound from Bilingual I (Sub I) or Bilingual II (Sub II). If you have poor reception on a stereo broadcast, you can change from stereo to mono sound so that you can hear the broadcast more clearly and easily.

s: Stereo sound v: mono sound

t : Bilingual I (sub I)

u: Bilingual II (sub II)

The sound mode you can choose differs depending on the TV programme.

This function does not work in the EXT modes.

BASS

You can adjust the low tone of the sound.

2: weaker

3: strong

TREBLE

You can adjust the high tone of the sound.

2: weaker

3: strong

BALANCE

You can adjust the volume balance between the left and right speaker.

2: turn the left speaker’s volume level up.

3: turn the right speaker’s volume level up.

HYPER SOUND

You can enjoy sounds with a wider ambience.

ON:

This function is turned on.

OFF:

This function is turned off. The menu disappears.

The HYPER SOUND function does not work properly with mono sound.

You can turn the HYPER SOUND function on or off with a single press. For details, see “HYPER SOUND function” on page 15.

Notes for Ireland model (AV-32T5SR/AV-32T5BR/AV-28T5SR/ AV-28T5BR)

-The HYPER SOUND function works only for the audio signal output from TV channels. It cannot work for the audio signal input from EXT sources.

-The HYPER SOUND function affects the audio signal output from the EXT-1 and EXT-2 terminals. If you want to output the normal audio signal from the EXT terminals, turn the HYPER SOUND function off.

24

FEATURES menu

FEATURES

 

SLEEP TIMER

 

 

BLUE BACK

ON

 

CHILD LOCK

 

TV

OK

 

D0023-EN

SLEEP TIMER

You can set the TV to automatically turn off after a set period of time.

1Choose SLEEP TIMER. Then press the aor 3button

A Sub-menu of the SLEEP TIMER function appears.

SLEEP TIMER

 

 

0

120

 

OFF

 

TV

OK

 

D0024-EN

2Press the 5buttons to set the

period of time.

Then press the abutton

You can set the period of time for up to 120 minutes (2 hours) in 10 minute steps.

One minute before the SLEEP TIMER function turns off the TV, “GOODNIGHT!” appears.

The SLEEP TIMER function cannot be used to turn off the TV’s main power.

When the SLEEP TIMER function is on, you can display the sub-menu of the SLEEP TIMER function again to confirm or change the remaining

period of time of the SLEEP TIMER function. Press the abutton to leave the menu after confirming or changing the remaining time.

To cancel the SLEEP TIMER function:

Press the 2button to set the period of time to “OFF”.

BLUE BACK

You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent, or when there is no input from an external device.

ON:

This function is turned on.

OFF:

This function is turned off.

CHILD LOCK

When there is a TV channel you do not want your children to watch, you can use the CHILD LOCK function to lock out the TV channel. Even when a child chooses a programme number (PR) for a locked TV channel the screen will change to blue and display n(CHILD LOCK) so the TV channel cannot be viewed. Unless you enter a pre-set ID number by a special operation, the lock cannot be released and the child cannot view the TV channel.

To set the CHILD LOCK function

1Choose CHILD LOCK, then press the 0button

“SET ID NO.” (ID number setting screen) appears.

SET ID NO.

0000

TV OK

D0025-EN

2Set the ID number to your liking

1Press the 6buttons to choose a number.

2Press the 5buttons to move the cursor.

25

FEATURES menu

3Press the abutton

The Sub-menu of CHILD LOCK appears.

CHILD LOCK

PR

ID

CH/CC

AV

 

 

1

BBC1

CH 21

2CH 22

3CH 23

4CH 24

5CH 25

6CH 26

TV

OK

LOCK

 

 

D0026-EN

4Press the 6buttons to choose a

TV channel

Every time you press the 6buttons, the Programme number (PR) changes, and the picture of the TV channel registered in the Programme number (PR) is displayed on the screen.

5Press the blue button and set the CHILD LOCK function.

Then press the abutton

n(CHILD LOCK) appears and the TV channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.

n(CHILD LOCK) disappears.

To disable easy resetting of the CHILD LOCK function, the menu disappears if

you choose the CHILD LOCK function and press the abutton.

To view a locked TV channel

1Choose a programme number (PR) of a locked TV channel with the number buttons or PR LIST

The screen changes to blue and the n (CHILD LOCK) appears. You cannot view the TV channel.

2Press the h(Information) button while the n(CHILD LOCK) is displayed

The “ID NO.” (ID NO. input screen) appears.

5

ID NO. :

D0028-EN

3Press the number buttons to enter the ID number

The lock is temporarily released so you can view the TV channel.

If you have forgotten the ID number:

Perform step 1 of “To set the CHILD

LOCK function”. After confirming the ID number, press the bbutton to exit the menu.

Even if you reset the lock temporarily, it does not mean that the CHILD LOCK function set for the TV channel is cancelled. The next time anyone tries to view the TV channel, it will be locked again.

When you want to cancel the CHILD LOCK function, you must perform the operation “To set the CHILD LOCK function” again.

To stop it being easy to choose the programme number (PR) of a locked TV channel, the programme number (PR) has been set so that it cannot be chosen with the 6buttons or the buttons of the TV.

To stop it being easy to reset the lock, “ID NO.” (ID No. input screen) is set so that it cannot appear unless you press the h(Information) button.

5

D0027-EN

26

Loading...
+ 58 hidden pages