GB Operator’s Manual
115 02 33-26
ENGLISH
SYMBOLS USED IN OPERATOR’S MANUAL:
Always disconnect power before performing cleaning or maintenance work.
Always use approved safety gloves.
Clean your chain saw regularly.
Use approved face mask or safety goggles.
|
Visual inspection. |
|
|
Do not use a coiled extension cord. |
|
|
|
|
|
Minimum wire cross-section: |
1,5 mm² |
|
Maximum cable length: |
30 m |
|
Voltage: |
230 V |
CAUTION!
Chain saws are dangerous! Careless or improper use can result in severe or fatal injury.
SYMBOLS ON THE CHAIN SAW:
CAUTION!
Chain saws are dangerous! Careless or improper use can result in serious or fatal injury.
Read operating instructions and make certain you understand them thoroughly before using the chain saw.
The chain saw is double-insulated.
Always use:
•Approved helmet
•Approved hearing protection
•Approved safety goggles or face mask
This product conforms to applicable CE directives.
Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specified in «TECHNICAL SPECIFICATIONS» page 3 and on label.
Do not expose saw to rain or moisture.
Disconnect power in case of damage to power cable.
Maximum permissible guide bar length.
This product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.
•Read operating instructions carefully.
•Always observe the «Safe Use» recommendations on page 4.
•Check chain and guide bar for correct assembly and adjustment.
•Start the saw.
•Do not start sawing until an adequate amount of oil has reached the chain.
•Incorrect chain tensioning increases wear on chain, sprocket and guide bar, and may result in damage to these parts.
•Improper use of power cable may lead to serious motor damage.
IMPORTANT!
Do not use a coiled power cable!
Minimum wire cross-section: |
1,5 mm² |
|
Maximum cable length: |
30 |
m |
Voltage: |
230 |
V |
CAUTION!
The chain saw must not be modified in any way under any circumstances without the permission of the manufacturer. Use only original accessories. Unauthorized modifications and/or accessories may cause serious or fatal injury of the operator or others.
2
Symbols |
2 |
Slip clutch |
11 |
|
Important! Read before using chain saw |
2 |
Electronic overload protection 2000W |
11 |
|
Contents |
3 |
Cutting equipment |
11 |
|
EC declaration of conformity |
3 |
Chain and guide bar lubrication |
12 |
|
Technical specifications |
4 |
- Chain oil |
12 |
|
Chain saw parts |
5 |
- Filling chain oil |
12 |
|
|
|
|||
Safe use |
5 |
- Checking automatic |
12 |
|
chain lubrication system |
|
|||
Starting and stopping |
7 |
|
||
- Checking chain wear |
12 |
|||
Daily inspection and maintenance |
7 |
|||
Filing chain |
13 |
|||
Kickback prevention |
8 |
|||
Limbing |
13 |
|||
Chain brake with kickback guard |
9 |
|||
Crosscutting |
14 |
|||
- Kickback guard inspection |
9 |
|||
Felling operations |
14 |
|||
- Manual chain brake function check |
9 |
|||
- Danger zone |
15 |
|||
- Inertia chain brake function check |
9 |
|||
- Felling direction |
15 |
|||
Mounting guide bar and adjusting chain |
10 |
|||
- Clearing branches/Line of retreat |
15 |
|||
Chain catcher |
11 |
|||
- Felling |
15 |
|||
|
|
|||
Right hand guard |
11 |
|
|
ENGLISH
EC DECLARATION OF CONFORMITY
Husqvarna Norge AS, N-1708 Sarpsborg, Norway hereby declares that the following chain saws:
Jonsered CS 2117EL and Jonsered CS 2121EL, with serial numbers starting at 54000001 and onwards,
-are manufactured in compliance with EC Directive 98/37/EC (Machinery), EC Directive 73/23/EEC including amendments (Low Voltage Directive), EC Directive 89/336/EEC including amendments (Electromagnetic Compatibility Directive), and in accordance with annex V of Directive 2000/14/EC (Noise Emission in the environment by equipment for use outdoors)
-are manufactured in compliance with the following harmonized standards: EN 50144-1, EN 50144-2-13, IEC 60745-1 and IEC 60745-2-13.
Notified body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has:
-carried out the EC type examination in accordance with the machinery Directive (98/37/EC) Article 8(2)(c)
-issued EC type examination certificates No. 404/04/1038 - Jonsered CS 2117 EL
and 404/04/1037 - Jonsered CS 2121 EL pursuant to machinery Directive 98/37/EC, Annex IV (4)
The chain saw submitted is identical to the samples submitted for EC type examination.
The measured and guaranteed sound power levels in accordance with Directive 2000/14/EC are set forth under Technical Data in the User’s Manual.
Sarpsborg, 1th of October 2005
Jan Hansen, President
3
ENGLISH
Motor |
|
1700 |
|
2000 |
||||||||||||
Rated voltage |
VAC |
220-240 |
|
230 |
||||||||||||
Rated output |
W |
1700 |
|
2000 |
||||||||||||
Frequency |
Hz |
50/60 |
|
50 |
||||||||||||
Slip clutch |
|
Yes |
Yes |
|||||||||||||
Electronic start control |
|
- |
|
Yes |
||||||||||||
Electronic speed control |
|
- |
|
Yes |
||||||||||||
Electronic overload protection |
|
- |
|
Yes |
||||||||||||
Weight |
|
|
|
|
||||||||||||
Without guide bar and chain |
kg |
4,4 |
|
4,4 |
||||||||||||
With 14” guide bar and chain |
kg |
5,1 |
|
5,1 |
||||||||||||
Chain lubrication |
|
|
|
|
||||||||||||
Oil tank volume |
litres |
0.1 |
|
0.1 |
||||||||||||
Oil consumption approx. |
litres |
0.1/20 min. |
0.1/20 min. |
|||||||||||||
Oil pump |
|
auto |
auto |
|||||||||||||
Noise levels |
|
|
|
|
||||||||||||
Equivalent noise intensity at operator’s ear, |
|
|
|
|
||||||||||||
according to international standards |
dB(A) |
95 |
|
95 |
||||||||||||
Noise emissions |
|
|
|
|
||||||||||||
Sound power, measured |
LW dB(A) |
104 |
|
104 |
||||||||||||
Sound power, guaranteed |
LWA dB(A) |
106 |
|
106 |
||||||||||||
Vibration |
|
|
|
|
||||||||||||
Front handle |
m/s2 |
4.4 |
|
4.4 |
||||||||||||
Rear handle |
m/s2 |
5,4 |
|
5,4 |
||||||||||||
Chain/guide bar |
|
|
|
|
||||||||||||
Recommended bar length |
inches/cm |
12/30 |
|
12/30 |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
inches/cm |
14/35 |
|
14/35 |
|
|
|
|
|
|
|
|
|
|
|
|
|
inches/cm |
16/40 |
|
16/40 |
Effective cutting length |
inches/cm |
12/30 |
|
12/30 |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
inches/cm |
14/35 |
|
14/35 |
|
|
|
|
|
|
|
|
|
|
|
|
|
inches/cm |
16/40 |
|
16/40 |
Chain speed, unloaded |
m/sec. (drive) |
14,5 (6 tooth) |
15,2 (6 tooth) |
|||||||||||||
Chain speed, rated output |
m/sec. (drive) |
12,5 (6 tooth) |
12,2 (6 tooth) |
|||||||||||||
Chain pitch |
inches |
3/8 |
|
3/8 |
||||||||||||
Gauge |
inches/mm |
.050/1.3 |
|
.050/1.3 |
||||||||||||
Number of drive links |
12”/14”/16” |
45/52/56 |
|
45/52/56 |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
inch |
inch/mm |
inch/mm |
inch/mm |
inch/cm/dl |
(
4
ENGLISH
1.Rear handle
2.Power trigger lockout
3.Front handle
4.Serial No. plate
5.Chain tensioner
6.Chain oil reservoir
7.Chain oil level
8.Ventilation slots
9.Power cable
10.Power trigger
11.Chain
12.Guide bar
13.Chain brake release button
14.Kickback guard
15.Chain drive cover
16.Right hand guard - protects right hand in case chain breaks or derails
17.Drive sprocket
-concealed by chain drive cover
18.Chain catcher - deflects chain in case chain breaks or derails
19.Guide bar nut
20.Nose sprocket
21.Scabbard
22.Combination tool
23.Operator’s manual
CAUTION!
Never operate a chain saw with one hand only. Doing so may lead to i serious injury to operator, helpers or bystanders. An electric chain saw is designed for operation with both hands.
DANGER!
Use of accessories not conforming to the recommendations outlined in the
Operating Instructions could lead to injury.
• Dress safely. Avoid jewellery and loose-fitting clothing, which may be caught in moving parts. Approved safety mitts and sturdy footwear which gives a good footing are recommended (also for helpers).
Wear: - Approved face mask or safety goggles
-Approved hearing protection
-Approved helmet
-Approved safety boots with protective rein-
forcement, steel toecap and non-slip soles - Clothing which is snug without hampering
movement
- Approved gloves with protective reinforcement
Always keep a first-aid kit on hand!
5