JLG X17J Operator Manual

Operation, Safety, Maintenance and service Manual

Original Instructions - Keep this manual with the machine at all times.

Boom Lift Models

X17JPLUS

X17JPR002

April, 2013

JLG LIFT

FOREWORD

For:

•Accident Reporting

•Product Safety Publications

•Current Owner Updates

•Questions Regarding Product Safety

•Standards and Regulations Compliance Information

•Questions Regarding Special Product Applications

•Questions Regarding Product Modifications

Contact:

Product Safety and Reliability Department

JLG Industries, Inc.

13224 Fountainhead Plaza

Hagerstown, MD 21742

or Your Local JLG Office

(See addresses on manual cover)

In USA:

Toll Free: 877 JLG SAFE (877 554 7233)

Outside USA:

Phone: [phone]

Fax: [phone]

E mail: [e-mail]

X17JPR002

JLG LIFT

FOREWORD

REVISION LOG

Rev.	Manual code	Date
Original Issue	X17JPR002	April, 2013

X17JPR002

BOOM LIFT MODELS X17JPLUS

JLG

TABLE OF CONTENTS

CHAPTER	1	PRESENTATION ....................................................................................	Page 08
CHAPTER	2	TECHNICAL INFORMATION ...........................................................	Page 09
	2.1	Description of the machine ...................................................................	Page 09
	2.1.1	Control position .....................................................................................	Page 09
	2.1.2	Machine identification plate .................................................................	Page 12
	2.1.3	Overall dimensions of the machine .....................................................	Page 13
	2.1.4	Technical specifications .........................................................................	Page 14
	2.1.4.1	Petrol engine technical specifications ..................................................	Page 15
	2.1.4.2	Diesel engine technical specifications..................................................	Page 15
	2.1.4.3	Hydraulic system technical specifications ..........................................	Page 15
	2.1.4.4	Electrical system technical specifications Thermic ............................	Page 16
	2.1.4.5	Electrical system technical specifications Lithium ............................	Page 16
	2.1.5	Terminology ............................................................................................	Page 17
	2.2	General safety standards ......................................................................	Page 18
	2.3	Safety warnings.......................................................................................	Page 22
	2.3.1	Generalities..............................................................................................	Page 22
	2.3.2	Noise and vibrations ..............................................................................	Page 22
	2.3.3	Pictograms positioned on the machine ...............................................	Page 23
CHAPTER	3	SAFETY DEVICES ..................................................................................	Page 37
	3.1	Battery cutout switch .............................................................................	Page 38
	3.2	Distributor pressure relief valves .........................................................	Page 38
	3.3	Cylinder stop valves ..............................................................................	Page 39
	3.4	Alignment photocell on the aerial part of the structure and the
		base of the machine ...............................................................................	Page 39
	3.5	Stabiliser position microswitches.........................................................	Page 40
	3.6	Jib position microswitch ........................................................................	Page 40
	3.7	Basket load sensor .................................................................................	Page 41
	3.8	Control protection ..................................................................................	Page 42
	3.9	Spirit level ...............................................................................................	Page 42
	3.10	Pin locking bolts and nuts ....................................................................	Page 43
	3.11	Safety device electronic control board.................................................	Page 43
CHAPTER	4	INSTRUMENTS AND CONTROLS ....................................................	Page 44
	4.1	Remote control ........................................................................................	Page 44
	4.1.1	Display .....................................................................................................	Page 45
	4.1.1.1	Display main screen ...............................................................................	Page 45
	4.1.2	Joysticks ...................................................................................................	Page 49
	4.1.3	Push buttons............................................................................................	Page 51
	4.2	Footswitch ...............................................................................................	Page 55
	4.3	Control positions ...................................................................................	Page 55
CHAPTER	5	EMERGENCY DEVICES .......................................................................	Page 56
	5.1	Emergency stop button..........................................................................	Page 56
	5.2	Hand pump .............................................................................................	Page 57
	5.3	Solenoid valves for emergency descent...............................................	Page 57
	5.4	Safety device bypass key .......................................................................	Page 58
	5.5	Emergency position controls ................................................................	Page 59
CHAPTER	6	USING THE MACHINE........................................................................	Page 64
	6.1	Safety standards to adopt before using the platform................................	Page 64
	6.1.1	Risk of electrocution...............................................................................	Page 64
	6.1.2	Danger due to atmospheric conditions ..............................................	Page 65
	6.1.3	Danger due to the work area ...............................................................	Page 65
	6.2	Procedures for correct use ....................................................................	Page 66
	6.2.1	Summary table of operator safety standards .........................................	Page 66
	6.3	Working area ..........................................................................................	Page 68
	6.4	Using the elevating work platform (MEWP) .....................................	Page 69

X17JPR0020413

1

BOOM LIFT MODELS X17JP

JLG

	6.4.1	Preliminary checks before starting work ...........................................	Page 70
	6.4.2	Starting the petrol/diesel engine .........................................................	Page 71
	6.4.3	Starting the electric motor ....................................................................	Page 72
	6.4.4	Stopping the engine/motor ...................................................................	Page 74
	6.4.5	Stopping the motor lithium version ....................................................	Page 74
	6.4.6	Travel ........................................................................................................	Page 75
	6.4.7	Jib arm movement for travel .................................................................	Page 78
	6.4.8	Parking the machine on a slope or on uneven ground ....................	Page 80
	6.4.9	Stabilising and levelling the machine ..................................................	Page 80
	6.4.10	Automatic lowering and raising of the stabilisers ............................	Page 84
	6.4.11	Track gauge extension............................................................................	Page 86
	6.4.12	Moving the basket .................................................................................	Page 87
	6.4.13	Manually levelling the basket ..............................................................	Page 91
	6.5	Emergency operations on the aerial part ...........................................	Page 92
	6.5.1	Emergency descent controlled from the basket ........................................	Page 92
	6.5.2	Operating the machine from the emergency control position
		on the ground if the operator is taken ill ............................................	Page 93
	6.5.3	Emergency descent in the case where the stabilisers are
		accidentally retracted .............................................................................	Page 94
	6.5.4	Emergency descent controlled from the ground using the hand
		pump in the event of faults on all energy supply systems .............	Page 96
	6.5.5	Emergency operations on the carriage: moving the platform
		stabilisers using the hand pump to allow the machine
		to be transported.....................................................................................	Page 98
	6.5.6	Emergency operation of the undercarriage in the event of
		movements of the aerial part ................................................................	Page 99
	6.6	Electrical disconnection of the remote control ..................................	Page 101
	6.7	Recharging the battery ..........................................................................	Page 102
	6.8	Main intended uses of the platform ....................................................	Page 106
	6.8.1	Systems.....................................................................................................	Page 106
	6.8.2	Closed environments .............................................................................	Page 106
	6.8.3	Pruning.....................................................................................................	Page 106
	6.8.4	Repair and maintenance of roofing and gutters ................................	Page 107
	6.8.5	Painting, sand blasting and plastering................................................	Page 107
	6.8.6	Use in marine environments ................................................................	Page 107
CHAPTER	7	MAINTENANCE....................................................................................	Page 108
	7.1	Safety instructions for greasing and lubrication ................................	Page 108
	7.2	Table of recommended lubricants ........................................................	Page 108
	7.3	Greasing points .......................................................................................	Page 109
	7.4	Greasing the telescopic arm ..................................................................	Page 110
	7.5	Safety instructions for maintenance operations.................................	Page 110
	7.6	Operating the machine from the second control position on the
		ground using the optional second remote control during
		maintenance ............................................................................................	Page 112
	7.7	Periodic maintenance intervals ............................................................	Page 113
	7.8	Electric motor .........................................................................................	Page 115
	7.8.1	Electric motor maintenance ..................................................................	Page 115
	7.9	Inspection and maintenance ................................................................	Page 116
	7.10	General periodic checks ........................................................................	Page 118
	7.11	Maintenance on the rubber tracks .......................................................	Page 119
	7.11.1	Checking the track tension ....................................................................	Page 119
	7.11.2	Loosening/tightening the tracks ...........................................................	Page 119
	7.11.3	Checking the rubber tracks ...................................................................	Page 120
	7.11.4	Replacing the rubber tracks ..................................................................	Page 122
	7.12	Checking tightness of nuts and bolts...................................................	Page 123
	7.13	Checking the hydraulic oil level...........................................................	Page 127
	7.13.1	Hydraulic oil............................................................................................	Page 127
	7.14	Checking for leaks in the hydraulic system........................................	Page 127

2	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

	7.15	Checking the condition of the filter cartridge ....................................	Page 128
	7.16	Checking that all the plates are present on the machine
		and intact .................................................................................................	Page 128
	7.17	Checking the operating pressure of the hydraulic system...............	Page 129
	7.18	Checking tightness of the fastening screws on the pin retainers
		and the locknuts......................................................................................	Page 129
	7.19	Checking wear on the extension arm internal sliding ring ..............	Page 130
	7.20	Checking wear on the telescopic arm slides .......................................	Page 130
	7.21	Checking tightness of the turntable bolts............................................	Page 131
	7.22	Battery: checks and maintenance thermic version ..........................	Page 131
	7.22.1	Checking the electrolyte level thermic version ................................	Page 131
	7.22.2	Recharging the battery thermic version............................................	Page 132
	7.22.3	Replacing the battery thermic version ..............................................	Page 133
	7.22.4	Battery disposal ......................................................................................	Page 133
	7.23	Battery pack operating specifications..................................................	Page 134
	7.23.1	Components and diagrams ...................................................................	Page 135
	7.23.2	Personal protective equipment .............................................................	Page 137
	7.23.3	Handling in dangerous conditions ......................................................	Page 137
	7.23.3.1	Procedure for handling hot cells ..........................................................	Page 138
	7.23.3.2	Procedure for handling vented cells ....................................................	Page 139
	7.23.3.3	Procedure for exploded cells.................................................................	Page 140
	7.23.3.4	Lithium battery fire ................................................................................	Page 142
	7.24	Servicing the engine ...............................................................................	Page 144
CHAPTER	8	SAFETY STANDARDS FOR TRANSPORT ........................................	Page 145
	8.1	Removing the basket..............................................................................	Page 145
	8.2	Loading and unloading the machine on transport vehicles
		using ramps .............................................................................................	Page 146
	8.3	Lifting the machine.................................................................................	Page 147
	8.3.1	Lifting the machine using a forklift .....................................................	Page 148
	8.3.2	Lifting the machine using ropes or chains..........................................	Page 149
	8.4	Transporting the machine......................................................................	Page 150
CHAPTER	9	SERVICE MENU ON THE REMOTE CONTROL .............................	Page 151
	9.1	Input menu ..............................................................................................	Page 151
	9.2	Error menu...............................................................................................	Page 153
	9.3	Operating hours menu...........................................................................	Page 153
	9.4	Settings menu..........................................................................................	Page 153
	9.5	Joystick menu ..........................................................................................	Page 153
CHAPTER	10	TROUBLESHOOTING...........................................................................	Page 154
CHAPTER	11	CHECKS TO BE COMPLETED ON THE MACHINE
		FOLLOWING REPAIRS.........................................................................	Page 162
	11.1	Checking correct operation of the controls.........................................	Page 162
	11.2	Checking operation of the safety devices............................................	Page 162
CHAPTER	12	HYDRAULIC SYSTEM ..........................................................................	Page 163
	12.1	Hydraulic system diagram thermic version .......................................	Page 163
	12.1.1	Key to the hydraulic system diagram thermic version .....................	Page 164
	12.2	Hydraulic system diagram lithium version........................................	Page 165
	12.2.1	Key to the hydraulic system diagram lithium version........................	Page 166
CHAPTER	13	WIRING DIAGRAM ..............................................................................	Page 167

X17JPR0020413

3

BOOM LIFT MODELS X17JPLUS

JLG

PREFACE

The aim of this manual is to provide the user with the necessary instructions and essential operating procedures to ensure correct and safe use of the machine for its intended purpo ses, as well as to prevent serious injury to the operator and other persons.

IMPORTANT

IT IS MANDATORY TO KEEP TO ALL THE INSTRUCTIONS GIVEN IN THIS MANUAL. THIS MANUAL MUST BE CAREFULLY READ AND UNDERSTOOD BEFORE OPERA TING THE MACHINE.

As this manual is an essential work tool, it must be kept with the machine at all times, in the special compartment, so as to be available for clarification whenever required.

As the manufacturer cannot control the conditions of the machine and the operations this is used for, THE USER IS RESPONSIBLE for ensuring compliance with the safety procedures described in this manual.

Every machine supplied is thoroughly adjusted and tested before being delivered. The ope rator does not need to perform any adjustments before using the machine.

Every alteration and/or modification of the features of the original machine design without previous written authorisation from the Constructor are PROHIBITED and THE RESPONSI BILITY FOR THESE ACTIONS FALLS ON THE OPERATOR.

THE EMPLOYER MUST MAKE SURE THAT THE OPERATOR HAS THE REQUISITES NECESSARY TO OPERATE THE MACHINE CORRECTLY AND THAT SUCH OPERA TOR HAS CAREFULLY EXAMINED AND UNDERSTOOD THE INFORMATION GIVEN IN THIS USER AND OPERATION MANUAL, RECEIVING SUITABLE TRAI NING REGARDING USE OF THE MACHINE IN STANDARD AND EMERGENCY CONDITIONS.

THE EMPLOYER MUST ALSO TRAIN OPERATORS REGARDING ANY NATIONAL STANDARDS THAT ARE IN ADDITION TO THE INSTRUCTIONS CONTAINED IN THIS DOCUMENT.

If the manual is damaged or lost, a copy must be requested directly from JLG.

4	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

Note: All of the photos and drawings in this manual have been added to simplify com prehension by the reader. Your machine may differ from the photos and drawings provi ded.

NORMATIVE REFERENCES

The machine has been designed, built and inspected according to that prescribed in the EN280 prA2:2009 harmonised standard, which supplies the presumption of conformity with the Essential Safety Requisites of the 2006/42/CE Machinery Directive even if a type C Volun tary Technical Standard.

According to that stated in EN280 prA2, the JLG platform is classified in GROUP B, as the vertical projection of the centre of gravity of the load can be outside of the tilting lines and in TYPE 1 as traversing is only allowed with the platform at rest.

The stability tests of the machine have been made in accordance with what described in paragraph 6.1.4.2 of the EN280 with load test calculated in conformity with 5.2.4 and have been successful.

In addition what prescribed in this manual it is necessary to apply the technical require ments of the following national/international safety standards:

UNI ISO 18893

ISO 16368

ISO 18878

With the exception of stricter local or national regulations in the working area of the MEWPS.

WARRANTY

On purchasing a JLG platform, a warranty and inspection certificate is issued that clearly indicates the warranty terms and where any interventions on the machine must be reported.

LIABILITY

The Constructor is exonerated from any liability and obligation for any injury/damage cau sed to persons/objects due to any of the reasons listed below:

•Failure to comply with the instructions indicated in this USE AND MAINTENANCE MANUAL regarding running, use and maintenance of the machine;

•Violent or sudden actions or incorrect manoeuvres when using or servicing the machine;

•Modifications made to the structure or machine components without previous authori sation from the Constructor and/or without the use of suitable equipment;

•Strange events with respect to normal and correct use of the machine, described in this USE AND MAINTENANCE MANUAL.

•Use of non original spare parts not authorised by the manufacturer.

X17JPR0020413

5

BOOM LIFT MODELS X17JPLUS

JLG

EC DECLARATION OF CONFORMITY

	EC DECLARATION OF
	CONFORMITY
Manufacturer	JLG Industries Inc
Address	1 JLG Drive
	McConnellsburg
	PA17233
	USA
Technical File:	JLG Industries Inc
	JLG Technology & Development Centre
	Bruntingthorpe Aerodrome & Proving Ground
	Lutterworth, Leicestershire
	LE17 5QS
	United Kingdom.
Authorised contact	Alan S. McIntyre	Position: Manager, Engineering
		Support - Europe
Machine Type:	Mobile Elevating Work Platform
Model Type:	...
Serial Number: ...
Notified Body:	ECO Certificazioni S.p.A
EC Number:	0714
Address	Via Mengollna
	33 - 48108
	Faenza
	Italy
Certificate Number:	To Be Advised
Reference Standards:	EN12100-1 & 2:2003 + A1:2009
	EN280:2001 + A2:2009

JLG Industries hereby declare that the above mentioned machine conforms with the requirements of:

2006/42/EC	Machinery
2004/108/EC	EMC Directive
2000/14/EC	Outdoor Noise

Signed:		Date:	...
Name:	Alan S. McIntyre	Position:	Manager,Engineering Support-
			Europe
		Place:	Bruntingthorpe, UK

Remark:

Any modification to the above described machine violates the validity of this declaration. This declaration conforms with the requirements of annex II-A of the council directive 2006/42/EC

Machine manufactured for JLG Industries Inc. by HINOWA S.p.a via Fontana 37054 NOGARA VR Italy

6	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

EC DECLARATION OF

CONFORMITY

Manufacturer	JLG Industries Inc
Address	1 JLG Drive
	McConnellsburg
	PA17233
	USA
Machine Type:	Mobile Elevating Work Platform
Model Type:	...
Serial Number:	...
Document Control:	HINOWA S.p.A		Technical File:	JLG Industries Inc
	Via Fontana - 37054			JLG Technology &
	Nogara			Development Centre
	Italy			Bruntingthorpe
				Aerodrome & Proving
				Ground
				Lutterworth,
				Leicestershire
				LE17 5QS
				United Kingdom.
Measured
Lwa	dB(A)...
Guaranteed
Lwa	dB(A)...
Engine Power:	kW	...
Lwa	= (Sound Power Level)
Applicable Procedure:	EN ISO 3744:1995
Applicable Directive:	2000/14/EC Annex V Internal Control of Production.

We hereby declare that the above mentioned machine conforms with the requirements of the "Noise Emission in the Environment by Equipment for Use Outdoors" Directive 2000/14/EC & 2005/88/EC

Remark:

This declaration conforms with the requirements of Annex II of the council directive 2000/14/EC

Any modification to the above described machine violates the validity of this declaration. Machine manufactured for JLG Industries Inc. by HINOWA S.p.a via Fontana 37054 NOGARA VR Italy

X17JPR0020413

7

BOOM LIFT MODELS X17JPLUS

JLG

1. PRESENTATION

This manual describes the warning signs used to draw the reader’s attention to several parti cularly important warnings.

The safety warnings are divided into two main types, which are identified and described below.

DANGER

This symbol accompanied by the word DANGER indicates that the situation described, if not prevented, can lead to serious injury or death of the persons involved (operator, ground staff, staff present in proximity to the platform, main tenance technicians etc.).

WARNING

This symbol accompanied by the word WARNING indicates that the situation described represents a potential risk for the structure of the machine.

Dangerous situations may be determined by this condition (including injury or death) for the persons involved.

8	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

2. TECHNICAL INFORMATION

2.1. DESCRIPTION OF THE MACHINE

The JLG machine is a self propelled hydraulic lifting device, equipped with a rotating work basket positioned at the top of an extendable articulated structure, which also rotates. The JLG lifting device is destined for the POSITIONING OF PERSONS AND THEIR EQUIP MENT AND MATERIALS IN HIGH POSITIONS WITH RESPECT TO GROUND LEVEL.

2.1.1 CONTROL POSITION

CONTROL POSITION IN THE BASKET

The JLG aerial work platform has been designed to be controlled by the operator in the basket using a remote control, where all of the machine functional controls are gathered, positioned in the relevant support inside the basket (see photo). A optional pedal button is also present in the basket to allow movement of the aerial part (photo). From this control position it is possible to control the extendible structure and machine stabilisation. When the machine is manoeuvred from the control position in the basket, the remote control must be positioned in the appropriate seat, and the footswitch must be activated (the footswitch must be release and activated again if no movements are made for more than 7 second). The remo te control is connected to the machine using a flexible cable that allows to shift it if the basket is to be removed or the ground control unit is to be used.

Stabilisation of the machine must be preferably controlled from the basket drive position. Machine traversing must be carried out from the control position on the ground.

ATTENZIONEDANGER

After accessing or leaving the control position in the basket, ALWAYS remember to close the ladder, to avoid any damage when operating the machine.

After leaving the control position in the basket, always remember to close the remote con trol protection cover.

X17JPR0020413		9

BOOM LIFT MODELS X17JPLUS

JLG

CONTROL POSITION ON THE GROUND:

There is a second control position available for the tracked part of the machine. This is not in a fixed position but rather can be located on the ground within a radius of 2.5 m from the basket attachment. To control the machine from this position, the operator uses the same remote control, removing it from its housing in the basket and using the cable provided.

From this control position, the operator IS NOT enabled to control the aerial part of the machine, but only the tracks, stabilisers and track extension func tion.

DANGER! when controlling the machine from the ground position, keep a distance of at least 1 m from the tracks.

DANGER! when controlling the machine from the ground position, always make sure that the component that is being moved is completely visible and constantly check its trajectory.

EMERGENCY CONTROL POSITION

There is a control position which will be identified as the emergency control position. This is located on the ground part of the machine, next to the distributor for the aerial part. To ena ble it, press the special selector positioned on the base of the turret (see photo) until the green warning light comes on. The light indicates that the movements of the aerial part are ena bled.

THERMIC MOTOR		LITHIUM MOTOR

From this position, the movements of the machine can be controlled directly using the levers on the various hydraulic distributors, aerial part (see photo 1) and proportional (aerial part, see photo 2).

ATTENZIONEDANGER

The emergency control position was designed to operate on the extensible structure only for emergency operations by emergency service personnel on the ground, who must in any case be trained and know the operation of the machine and its safety devices, as well as for maintenance and checks before starting work.

10	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

If an operator is in the basket, it is forbidden to move the structure from the ground posi tion, unless in an emergency situation (sudden operator illness, technical fault).

PHOTO 1

PHOTO 2

There is a control position available only for scheduled and unscheduled maintenance opera tions, placed near the electrical components compartment on the machine.

On the electric board protection there is an auxiliary connector for the connection of the optional second remote control (see photo).

OPTIONAL SECOND REMOTE	OPTIONAL SECOND REMOTE
CONTROL CONNECTOR POSITION	CONTROL CONNECTOR

To enable this position, use the key selector placed on the base of the turret and connect the optional second remote control to the machine.

Before proceeding with the connection, carefully read the paragraph regarding the use of the optional second remote control.

ATTENZIONEDANGER

This control position can only be used to carry out checks and maintenance on the machine. Do not use this position to control the machine during normal operations.

Note: it is absolutely forbidden to move the machine from this position if one ore more operators are in the basket.

X17JPR0020413

11

BOOM LIFT MODELS X17JPLUS

JLG

2.1.2 MACHINE IDENTIFICATION PLATE

The manufacturer plate is placed on the protection of the aerial part hydraulic distributor. The drawing is shown below.

	xsm1;Manufactured by
	HINOWA S.p.A.
	Via Fontana
JLG Industries. Inc - McConnellsburg. PA - USA	37054 NOGARA (VR)
	ITALY

Model

Serial number

Date of manufacture

G.V.W. (Dry)	kg
MAXIMUM ALLOWABLE OPERATING INCLINATION	1°

				=	+
MAX
12.5	M/S	230	kg	2x80	kg	70	kg	400	N
								07253100

12	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

2.1.3 OVERALL DIMENSIONS OF THE MACHINE

Maximum length in travel configuration with basket installed ......................

4529 mm

Track width ..............................................................................................................

798/1086 mm

Maximum height in travel configuration with foot plates removed ..............

2000 mm

Maximum attachment angle..................................................................................

20°

Maximum stabilisation angle ................................................................................

12°

Max stabiliser base side (disc centre) ..................................................................

2890x2885 mm

Nota: standard version with two operator basket.

X17JPR0020413

13

BOOM LIFT MODELS X17JPLUS

JLG

2.1.4 TECHNICAL SPECIFICATIONS

	PLATFORM CAPACITY	230 kg
	PLATFORM HEIGHT (floor)	14,96 m
	MAX WORKING HEIGHT	17,06 m
	STANDARD BASKET DIMENSIONS	1335 x 690 x H1100 mm
	HORIZONTAL EXTENSION	7,00 m
	MAX HORIZONTAL OUTREACH	7,50 m
	ROTATION (non-continuous)	360°
	BASKET ROTATION	124° (+/- 62°)
	MAX GROUND REACTION FORCE FOR EACH	1731 daN
	STABILISER
	MAX GROUND PRESSURE FOR EACH STABILISER	2,45 daN/cm2
	NO. OF OPERATORS	2
	NO. OF OPERATORS WITH OPTIONAL SINGLE-OPERATOR	1
	BASKET
	JIB - TYPE OF ARTICULATED JOINT	89°(+0°/-89°)
	MAX WORKING GRADIENT	1°/1,75%
	MAX STABILISATION SLOPE	12°
	TOTAL WEIGHT IN TRANSPORT CONFIGURATION	2230 kg
	ENGINE	HONDA iGX440 - (12,7cv) / 3600rpm
		HATZ 1B40 - (10,2cv) / 3600rpm
	ELECTRIC MOTOR	2,2 kw / 230V / 50Hz 1500 rpm
	ELECTRICAL SYSTEM VOLTAGE	12 V
	PUMPS PETROL ENGINE	double 2x4 cc
	PUMPS DIESEL ENGINE	double 2x4 cc
	MAX TRAVEL SPEED THERMIC ENGINE	1,8 km/h
	MAX TRAVEL SPEED THERMIC ENGINE WITH OPTIONAL 2ND	0,7 / 1,8 / 3,6 km/h
	SPEED
	TRAVEL/STAB. SYSTEM PRESSURE	165 bar
	AERIAL PART SYSTEM PRESSURE	185 bar
	MAX SLOPE ALLOWED IN TRAVEL DIRECTION	15°
	MAX WIND SPEED	12,5 m/s
	MAX MANUAL FORCE ALLOWED	400 N

NB: Side extension is measured from the centre of the turntable to the outside edge of the basket.

14	X17JPR0020413

BOOM LIFT MODELS X17JPLUS
JLG
2.1.4.1 TECHNICAL DATA – PETROL ENGINE
Make/Model ................................................................................	HONDA iGX440
Fuel/Cooling ................................................................................	PETROL/AIR
Power SAEJ1349 ..........................................................................	9,5 Kw (12,7cv) / 3600rpm
Max speed ....................................................................................	3600 rpm
Maximum torque ........................................................................	29,8 Nm/2500 rpm (80/1269/EC)
Number of cylinders ............................................................................	1
Displacement ..............................................................................	440 cm3
Sound power level at operator’s ear ........................................	88 dB
Measured sound power level ..................................................	102 dB
Granted sound power level ......................................................	104 dB
2.1.4.2 TECHNICAL DATA – DIESEL ENGINE
Make/Model ................................................................................	HATZ 1B40
Fuel/Cooling ................................................................................	DIESEL/AIR
Power SAEJ1349 ..........................................................................	7,5 Kw (10cv) / 3600rpm
Max speed ....................................................................................	3600 rpm
Maximum torque ........................................................................	25 Nm/2000 rpm (80/1269/EC)
Number of cylinders ............................................................................	1
Displacement ..............................................................................	462 cm3
Sound power level at operator’s ear ........................................	94 dB
Measured sound power level ..................................................	102 dB
Granted sound power level ......................................................	104 dB

2.1.4.3 HYDRAULIC SYSTEM TECHNICAL SPECIFICATIONS

Hydraulic oil tank capacity ......................................................	40 litres
Pump petrol engine ....................................................................	double pump 2x4 cm3
Pump diesel engine ....................................................................	double pump 2x4 cm3
Hydraulic system max pressure ..............................................	210 bars

For further information, see the hydraulic diagram enclosed with the manual and the para graph on maintenance of the hydraulic components.

X17JPR0020413

15

BOOM LIFT MODELS X17JPLUS

JLG

2.1.4.4 ELECTRICAL SYSTEM TECHNICAL SPECIFICATIONS THERMIC

Battery ................................................................................	55 Ah 240 A 12V
Alternator petrol engine ..................................................	20 A (3600 rpm)
Alternator diesel engine ..................................................	14 A (3000 rpm)
Electric motor: rated voltage..........................................	230 V
frequency............................................	50 Hz
rated power ........................................	2,2 kW

For further information, see wiring diagram enclosed with the manual and the paragraph on maintenance of electrical components.

2.1.4.5 ELECTRICAL SYSTEM TECHNICAL SPECIFICATIONS LITHIUM

Battery ................................................................................	90 Ah 48V
Electric motor: rated voltage ......................................	48 V
rated power ........................................	2 kW
Sound power level at operator’s ear ..............................	70 dB
Measured sound power level ..........................................	86 dB
Granted sound power level..............................................	88 dB

Onboard battery charger…………………………………220V±30V 50÷60Hz Battery charger (option)………………………………....110V±30V 50÷60Hz

For further information, see wiring diagram enclosed with the manual and the paragraph on maintenance of electrical components.

16	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

2.1.5 TERMINOLOGY

To make the contents of this manual easier to understand, the diagram provided below illu strates the terms used to identify the parts of the platform.

KEY

1	Tracked undercarriage	19	Extension arm
2	Revolving turret	20	Jib cylinder
3	Turntable + rotation motor	21	Right jib arm
4	Emergency controls	22	Left jib arm
5	Base+electrical component compartment+oil tank	23	Remote control for fault management
6	Double gear pump	24	Basket or cage
7	Petrol/diesel engine / Battery pack + inverter +	25	Basket support
	battery charger (LITHIUM MOTOR)
8	Stabiliser	26	Rotary actuator for basket rotation
9	Stabiliser cylinder	27	Basket levelling cylinder on the basket
10	Second arm tie rod	28	Jib transmission
11	Second arm	29	First-second arm transmission
12	Second-third arm cylinder	30	First-second arm cylinder
13	Second-third arm transmission	31	First arm
14	Second-third arm connecting rod	32	First arm tie rod
15	Basket levelling cylinder on the transmission	33	Electric motor
16	Third arm	34	Double gear pump
17	Stabiliser plate	35	Emergency hand pump
18	Jib tie rod

X17JPR0020413

17

BOOM LIFT MODELS X17JPLUS

JLG

2.2 GENERAL SAFETY STANDARDS

ATTENZIONEDANGER

The functioning of the MEWPS must be in compliance with international standards of refe rence (see paragraph “NORMATIVE REFERENCES” in the first pages of the manual) and national or regional standards if stricter.

The operator must read, understand and follow all the instructions and warnings, contained in this manual and on the machine, regarding the safe use of the MEWPS.

FAILURE TO COMPLY WITH THE SAFETY PRECAUTIONS LISTED IN THIS SECTION AND PROVIDED ON THE MACHINE CAN DAMAGE THE MACHINE AND CAUSE INJURY OR EVEN DEATH, AND CONSTITUTES A SERIOUS BREACH OF THE SAFETY RULES.

This section of the USER AND OPERATION MANUAL describes those procedures or dan gerous situations that can cause damage/injury to objects/persons and explains what the operator must do to prevent them.

•Operators must always act professionally, complying with safety standards, making sure not to underestimate their responsibility to themselves and the surrounding objects and per sons.

•Before starting work, operators must receive complete and clear training regarding the use of the machine in standard and emergency conditions. They must examine, under stand and take in all the instructions given in this user manual. They must be sure that the safety devices are in perfect working order, perform the necessary checks on the machine and be familiar with the conditions of the ground on which the machine is going to be operated and stabilised.

•The presence of at least one specialist operator is necessary on the ground during work. This person must know how to use the machine, be aware of the contents of the USER AND OPERATION MANUAL and be able to intervene if necessary.

•It is prohibited to make modifications to the machine that could jeopardise functioning and safety, without previous written authorisation from The Constructor which is not liable for any injury or damage caused by this behaviour.

Clothing and protective equipment

Avoid wearing loose clothing, rings, watches or anything else that may get caught in moving parts.

When using the machine or performing maintenance, wear a hard hat, glasses, safety footwear, gloves and acoustic ear muffs after making sure these and all other PPE that the safety manager considers necessary based on the risk analy sis performed are in perfect working condition.

18	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

IMPORTANTEWARNING

USE THE TYPE APPROVED AND CERTIFIED SAFETY HARNESSES. BEFORE WORKING AT A HEIGHT, MAKE SURE THAT THE SAFETY HARNESSES ARE COR RECTLY FASTENED AND CONNECTED TO THE ANCHORAGE POINTS ON THE BASKET.

THE USE OF HARNESSES IS COMPULSORY IN ACCORDANCE WITH LOCAL LEGISLATION IN EACH INDI VIDUAL COUNTRY. IN COUNTRIES WHERE THE LAW DOES NOT REQUIRE THE USE OF SUCH SAFETY SYSTEMS, THE EMPLOYER AND/OR USER IS RESPONSIBLE FOR CHOOSING THE SYSTEM TO BE USED.

Safety valves and electrical system safety components

It is prohibited to modify and/or tamper with the safety and control valves of the main hydraulic system and the adjustments of the electric plant. The Constructor is not liable for injury to persons and damage to objects or to the machine if the standard calibration of any hydraulic and electric/electronic component is tampered with.

Fire prevention

Keep the area around the motor clean, removing fragments of wood, paper and other flammable products; clean any fuel leaks as these may be a potential cause of fire.

Petrol is extremely flammable and explosive in particular con ditions. Refuel in well ventilated areas and with the engine at rest.

Avoid smoking and producing sparks in the refuelling and fuel storage area.

After refuelling, make sure to put back the cap correctly. Take care to avoid touching the exhaust silencer when this is hot, i.e. with the machine running or soon after stopping the engine.

Preventing damage caused by washing the machine

Do not direct high pressure jets towards the electrical compo nents while washing the machine. Do not use chemical deter gents or petrol that would damage the plastic parts and the painting.

BEFORE WASHING THE MACHINE, ALWAYS REMEMBER TO REMOVE THE REMO TE CONTROL AND CORRECTLY CLOSE THE REMOTE CONTROL AND EQUIP MENT CONNECTION SOCKETS LOCATED ON THE MACHINE.

X17JPR0020413

19

BOOM LIFT MODELS X17JPLUS

JLG

as shown in the figure in point 2.1.5.

ATTENZIONEDANGER

When washing the machine, the ignition block must be disengaged, the key removed and the emergency stop button pressed.

• Washing the outside of the machine

Never use flammable liquids. Adopt the above safety measures to prevent sparks due to short circuits.

If washing the track with water cleaners, carefully protect all the important parts and above all the electrical components. Follow the instructions provided by the manufacturer of the detergent.

1001125483

Clean the machine using water soluble detergents.

IMPORTANT

The more the elevating platform is cleaned, the more it will need to be greased (see par. 7.3 Grease points).

ATTENZIONEDANGER

Do not wet the electric motors and the other electrical components directly. Do not aim the spray directly onto adhesive labels and rating plates.

• Cleaning the electrical system

ATTENZIONEDANGER

Never clean the inverter or the electric motor with water, as this may cause damage to the electrical system.

1001125483

20	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

IMPORTANTEWARNING

Only use dry detergents, in accordance with the manufacturer’s instructions. Never remove covers, guards and the like.

Clean the electrical system using a dry, non metallic brush and low pressure air.

• After cleaning

Dry the machine carefully before starting it again (for example using compressed air).

ATTENZIONEDANGER

If, despite all the precautions, moisture has penetrated into the electric motor or other parts of the electric system, these must be dried using compressed air to avoid the risk of short cir cuits.

Preventing damage that may be caused by the machine during work

When the machine has been stabilised and work has started, never enter its operating area. Always operate the controls slowly and smoothly and avoid reversing the movements sud denly.

When operating outside of the basket, ALWAYS keep a MINIMUM distance of 1 METRE from the machine.

X17JPR0020413

21

BOOM LIFT MODELS X17JPLUS

JLG

2.3 SAFETY WARNINGS

2.3.1 GENERALITIES

To avoid accidents, before starting work and before performing any maintenance operations, it is necessary to read, understand and follow all the precautions and warnings contained in this manual. The user/operator of the machine must decline all responsibility for operation until having read this manual and fully understood how to use the machine under the supervision of an expert and qualified operator.

Carefully read all the safety messages provided in this manual and machine.

Keep the safety signs in good condition and replace them if they are Make sure that any new components on the machine are provided with

2.3.2 NOISE AND VIBRATIONS

The JLG platforms with electric motor have been tested according to pean directive 2000/14 EC, with the guaranteed sound power level the machine’s EC declaration of conformity.

When operating the aerial part of the machine, this value is reduced basket moves away from the main source of noise.

The vibrations transmitted to the operator from the controls and the basket are lower than the maximum allowed limits.

22

BOOM LIFT MODELS X17JPLUS

JLG

2.3.3 PICTOGRAMS POSITIONED ON THE MACHINE

Here we report the positions of the various boards with pictograms on the machine.

X17JPR0020413

23

BOOM LIFT MODELS X17JPLUS

JLG

24	X17JPR0020413

BOOM LIFT MODELS X17JPLUS

JLG

POS.	CODE	Q.ty
1	6555500	1
2	6555600	1
3	6555700	1
4	6555800	1
5	6041200	4
6	1001125483	7
7	1706898	1
8	6924300	1
9	1706493	1
10	6040500	2
11	6040900	5
12	6041300	13
13	1703814	4
14	6044000	8
15	6086600	2
16	1704277	2
17	1705828	1
18	7056700	2
19	1701499	4
20	7058800	2
21	6040300	4
22	1706098	1
23	7349200	1
24	7056800	3
25	06086000	1
26	06085900	1
27	06706500	1
28	06998800	1
29	07242000	1
30	1702155	1
31	1701504	1
32	06164700	1
33	06165000	1
34	06060000	1
35	06227200	1

POS.	CODE	Q.ty
36	1701542	1
36	1701505	1
37	06056300	1
38	06164600	1
39	06232100	1
40	07240300	1
41	07198800	4
42	07034200	2
43	07243000	1
44	1608710001	1
45	1608710002	1
46	07199100	1
47	06254800	1
48	07350300	4
49	07071000	1
50	06136900	1

X17JPR0020413

25

BOOM LIFT MODELS X17JPLUS

JLG

LANGUAGE STICKERS

POS.	CODE	Q.ty
	172428IT
L1	06555300	1
L2	06561200	5
L3	06448200	2
L4	06448100	2
L5	07319100	1
	172428GB
L1	06562600	1
L2	06561200	5
L2	06042400	5
L3	06462700	2
L4	06462100	2
L5	073191GB	1
	172428FR
L1	06562700	1
L2	06561200	5
L3	06462800	2
L4	06462200	2
L5	073191FR	1

POS.	CODE	Q.ty
	172428PT
L1	06563100	1
L2	06561200	5
L3	06463200	2
L4	06462600	2
L5	073191PT	1
	172428DA
L1	07138100	1
L2	06561200	5
L3	07138000	2
L4	07137900	2
L5	073191DA	1

POS.	CODE	Q.ty
	172428DE
L1	06562800	1
L2	06561200	5
L3	06462900	2
L4	06462300	2
L5	073191DE	1
	172428ES
L1	06562900	1
L2	06561200	5
L3	06463000	2
L4	06462400	2
L5	073191ES	1
	172428NL
L1	06563000	1
L2	06561200	5
L3	06463100	2
L4	06462500	2
L5	073191NL	1

POS.	CODE	Q.ty
	172428SW
L1	07137300	1
L2	06561200	5
L3	07137500	2
L4	07137400	2
L5	073191SW	1
	172428NO
L1	07162000	1
L2	06561200	5
L3	07161800	2
L4	07161900	2
L5	073191NO	1

26	X17JPR0020413