This manual has been prepared for the owner and operators of a JWSS-10CS SuperSaw. Its purpose,
aside from machine operation, is to promote safety through the use of accepted correct operating and
maintenance procedures. Completely read the safety and maintenance instructions before operating or
servicing the machine. To obtain maximum life and efficiency from your JET SuperSaw, and to aid in
using the machine safely, read this manual thoroughly and follow instructions carefully.
Warranty
WMH Tool Group warrants every product it sells. If a tool needs service or repair, one of our Authorized
Repair Stations located throughout the United States can give you quick service.
In most cases, any one of these WMH Tool Group Repair Stations can authorize warranty repair, assist
you in obtaining parts, or perform routine maintenance and major repair on your JET, Wilton, or
Powermatic tools.
For the name of an Authorized Repair Station in your area, please call 1-800-274-6848, or visit
www.wmhtoolgroup.com
More Information
WMH Tool Group is consistently adding new products to the line. For complete, up-to-date product
information, check with your local WMH Tool Group distributor, or visit www.wmhtoolgroup.com
WMH Tool Group Warranty
WMH Tool Group (including JET, Wilton and Powermatic brands) makes every effort to assure that its
products meet high quality and durability standards and warrants to the original retail consumer/purchaser
of our products that each product be free from defects in materials and workmanship as follow: 1 YEAR
LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE. This Warranty does
not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-andtear, repair or alterations outside our facilities, or to a lack of maintenance.
WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE,
FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN,
ANY IMPLIED WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WMH TOOL GROUP SHALL IN NO EVENT BE
LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL,
CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR
PRODUCTS. SOME STATES DO NOT ALLOW THE EXLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU.
To take advantage of this warranty, the product or part must be returned for examination, postage
prepaid, to an Authorized Repair Station designated by our office. Proof of purchase date and an
explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we
will either repair or replace the product, or refund the purchase price if we cannot readily and quickly
provide a repair or replacement, if you are willing to accept a refund. We will return repaired product or
replacement at WMH Tool Group’s expense, but if it is determined there is no defect, or that the defect
resulted from causes not within the scope of WMH Tool Group’s warranty, then the user must bear the
cost of storing and returning the product. This warranty gives you specific legal rights; you may also have
other rights, which vary from state to state.
WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right to
effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment, which
they may deem necessary for any reason whatsoever.
Table of Contents..........................................................................................................................................3
Installing the Blade ..................................................................................................................................19
115 Volt Operation...................................................................................................................................22
230 Volt Operation...................................................................................................................................22
Parts ............................................................................................................................................................ 29
XACTA Fence II Homeshop 30/52 Fence Assembly .............................................................................. 29
To order parts or reach our service department, call 1-800-274-6848 between 7:00 a.m. and 6:00 p.m.
(CST), Monday through Friday. Having the Model Number and Serial Number of your machine available
when you call will allow us to serve you quickly and accurately.
4
Warnings
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This Table Saw is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a Table Saw, do not use until proper
training and knowledge has been obtained.
5. Do not use this Table Saw for other than its intended use. If used for other purposes, WMH Tool
Group disclaims any real or implied warranty and holds itself harmless from any injury that may result
from that use.
6. Always wear approved safety glasses/face shields while using this Table Saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this Table Saw, remove tie, rings, watches and other jewelry, and roll sleeves up
past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor
strips are recommended. Do not wear gloves.
8. Always use the blade guard on all ''through-sawing'' operations. A through-sawing operation is one in
which the blade cuts completely through the workpiece.
9. Kickback occurs when the workpiece is thrown towards the operator at a high rate of speed. If you do
not have a clear understanding of kickback and how it occurs, DO NOT operate this table saw!
10. Wear ear protectors (plugs or muffs) during extended periods of operation.
11. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead based paint.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically treated lumber.
12. Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
13. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
14. Make certain the switch is in the OFF position before connecting the machine to the power supply.
15. Make certain the machine is properly grounded.
16. Make all machine adjustments or maintenance with the machine unplugged from the power source.
17. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
18. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
19. Make sure the Table Saw is firmly secured to the floor or bench before use.
20. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
5
21. Provide for adequate space surrounding work area and non-glare, overhead lighting.
22. Keep the floor around the machine clean and free of scrap material, oil and grease.
23. Keep visitors a safe distance from the work area. Keep children away.
24. Make your workshop child proof with padlocks, master switches or by removing starter keys.
25. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
26. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do
not overreach or use excessive force to perform any machine operation.
27. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
28. Use recommended accessories; improper accessories may be hazardous.
29. Maintain tools with care. Keep saw blades sharp and clean for the best and safest performance.
Follow instructions for lubricating and changing accessories.
30. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
31. Do not stand on the machine. Serious injury could occur if the machine tips over.
32. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
33. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
6
Themost common accidents among table saw users, according to statistics, can
be linked to kickback, the high-speed expulsion of material from the table that can strike the
operator. Kickback can also result in operator’s hands being pulled into the blade.
Kickback Prevention
Tips to avoid the most common causes of
kickback:
• Make sure the blade splitter is always
aligned with the blade. A workpiece can bind
or stop the flow of the cut if the blade splitter
is misaligned and result in kickback.
• Use the blade splitter during every cut. The
blade splitter maintains the kerf in the
workpiece, which will reduce the chance of
kickback.
• Never attempt freehand cuts. The workpiece
must be fed perfectly parallel with the blade,
otherwise kickback will likely occur. Always
use the rip fence or crosscut fence to
support the workpiece.
• Make sure that the rip fence is parallel with
the blade. If not, the chances of kickback are
very high. Take the time to check and adjust
the rip fence.
• Feed cuts through to completion. Anytime
you stop feeding a workpiece that is in the
middle of a cut, the chance of binding,
resulting in kickback, is greatly increased.
Protection Tips from
Kickback
Kickback can happen even if precautions are
taken to prevent it. Listed below are some tips to
protect you if kickback DOES occur:
• Stand to the side of the blade when cutting.
An ejected workpiece usually travels directly
in front of the blade.
• Wear safety glasses or a face shield. Your
eyes and face are the most vulnerable part
of your body.
• Never place your hand behind the blade. If
kickback occurs, your hand will be pulled
into the blade.
• Use a push stick to keep your hands farther
away from the moving blade. If a kickback
occurs, the push stick will most likely take
the damage that your hand would have
received.
Specifications
Stock Number ..................................................................................................................................... 708781
Maximum Depth of Cut ..........................................................................................................................3-1/8”
Maximum Thickness at 45° Cut .............................................................................................................2-1/4”
Table in Front of Saw Blade at Maximum Cut .....................................................................................11-3/8”
Maximum Width of Dado....................................................................................................................... 13/16”
Maximum Diameter of Dado ........................................................................................................................8”
Dust Port Diameter....................................................................................................................................... 4”
Motor ...........................................................................................1-3/4 HP, 1Ph, 115V/230V prewired 115V
Net Weight (approx.) .......................................................................................................................... 436 lbs.
The specifications in this manual are given as general information and are not binding. WMH Tool Group
reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings,
and accessory equipment deemed necessary for any reason whatsoever.
7
Read and understand the entire
contents of this manual before attempting
assembly or operation! Failure to comply may
cause serious injury
1. Remove the arbor pulley guard (A). This is
only needed for the sliding table.
2. Attach left extension wing (B) to the table with
four socket head cap screws, four lock
washers and four flat washers (C). Snug but
do not tighten.
3. Slide extension wing toward the front edge of
the saw table until two faces are flush.
4. Place a straight edge across the table and left
extension wing. Align the extension wing the
same height as the saw table and tighten
socket head cap screws.
Note: Use a rubber mallet to align wing with
table.
Miter Gauge for Left Extension Wing
Hardware: Miter Gauge
Tools: Cross Point Screw Driver, Square
1. Change the angle on the miter gauge by
loosening handle (E, Fig. 7) and turning the
fence (F, Fig. 7) to desired angle. To move
gauge beyond index stops of 45° and 90°, flip
back the stop (G, Fig. 7).
2. Adjust index stops by turning one of three
adjustment screws (H, Fig. 7). Use a square
to verify that the fence is 90° to the saw blade,
see Figure 7.
Figure 6
Figure 7
3. Slide fence to the left, or right by loosening
handle (I, Fig. 7). Make sure fence does not
interfere with the blade when cutting.
11
The fence on the miter gauge must not contact
the saw blade! Failure to comply may cause
serious injury!
3. You can adjust the play in the miter gauge by
tightening the setscrews (J, Fig. 7).
The procedure for installing the leveling brackets is
the same for front rail and back rail. The illustration
(Figure 8) shows the front rail.
1. Place two washers (B) on two M8x25 hex cap screws (A). Insert through the mounting slots
of the front rail (C) and secure to the threaded
holes of the leveling bracket (D). Thread
screws only until they begin to protrude through the leveling bracket at this time.
2. Thread two M6 hex nuts (F) all the way onto
the four M6x25 socket head cap screws (G)
and screw into the leveling bracket (D).
3. Install the remaining leveling bracket onto the
back rail repeating the procedure outlined in
Steps 1 and 2.
4. The arbor pulley guard (H, Fig. 9) should be
attached to the saw cabinet.
5. You need to leave a gap between rails
(C, Fig 8) and the brackets (D, Fig. 8) so that
you can set the sliding table in position.
6. Mount table lock knob (J, Fig. 9) to the sliding
table (K, Fig. 9) with two M6x12 socket head
screws. Rotate knob 90° to engage/disengage
lock.
Make sure that the lock knob is
in the locked position and that the table is locked (does not slide on its support plate).
Failure to do so could result in injury when
attempting installation!
7. Place the sliding table (K, Fig. 9) onto the
leveling brackets (L, Fig. 9).
Figure 8
Figure 9
12
The support plate underneath the sliding table
(Figure 10) has an inner tab (A) and an outer
tab (B). When placing the table onto the
leveling bracket (D, Fig. 8), the leveling bracket
must be positioned between the inner and
outer tabs and the slots in the tabs (C, Fig. 10)
must straddle the screws (A, Fig. 8) that
secure the leveling bracket (D, Fig. 8) to the
rail (C, Fig. 8).
8. The sliding table should rest on the jacking
screws (G, Fig. 8).
9. Place two 90° 0.02” shims between the sliding
table and the table saw table near each end.
This will help keep the sliding table parallel to
the table saw table maintaining the proper
clearance.
10. Lower, or raise jacking screws (G, Fig. 8) so
that the sliding table surface is approximately
flush, or slightly lower than table saw table
surface.
Figure 10
11. Snug the four hex cap screws (A, Fig. 11) but
do not tighten. This will allow you to fine tune
the sliding table with the jacking screws.
12. Place a flat 0.02” shim (C, Fig. 11) on the table
saw tabletop for the straight edge (B, Fig. 11)
to rest on. This will help keep the sliding table
the right height above the top of the table saw.
13. Use two jacking screws (G, Fig. 8) to raise the
sliding table until it contacts the straight edge.
The straight edge should rest flat on sliding
table and shims.
14. Move straight edge to the other end of the
table saw tabletop and repeat step 12.
15. Tighten hex nuts (F, Fig. 8) against the leveling
bracket tabs while keeping jacking screws
(G, Fig. 8) from turning.
16. Tighten the four hex cap screws (A, Fig. 11)
that hold the leveling brackets in place.
Figure 11
Note: When tightening the screws on the rear
rail you may need to hold the sliding table
against the shims because there is a tendency
for the sliding table to move away from the
shim (Figure 12).
17. All jack screws (G, Fig. 8) should contact the
sliding table support plate (Figure 12).
Figure 12
13
18. Remove the shims and make sure the sliding
table is still approximately 0.02” higher than
the table saw tabletop; it is still approximately
0.02” away from the table saw tabletop.
Sliding Table Miter Gauge
Hardware: Miter Gauge, Fence, (2) Handles,
Stop, Fence Bar, Indicator Bar, Bushing, Bracket
Clamp Assembly & (2) Handles
Tools: 2.5mm Hex Wrench
1. Slide the miter gauge fence (B, Fig. 13) into
the bar (A, Fig. 13) and attach to the miter
gauge body (C, Fig. 13) with two handles
(D, Fig. 13).
Note: the 45° mitered end of the miter gauge
fence should be on the side of the blade.
2. Place miter gauge on the sliding table. There
are three sets of threaded holes.
• (1, Fig. 14) One set of threaded holes, up
front to the far left, are for 90°-45° cutting.
• (2, Fig. 14) The staggered set of threaded
holes, up front to the right, are for 90°-135°
cutting. Note: using this position with the
blade tilted to 45° you need to remove the
miter gauge handle found on the right side
and replace with the supplied 90° handle.
• (3, Fig. 14) The set of threaded holes, on
the far side, are used for cutting at 90°.
Referring to Figure 13:
3. Place indicator bar (E) on top of the miter
gauge body and secure in place with bushing
(F), bracket (G) and handles (H).
Figure 13
4. Slide the square nut (I) into the slot on top of
the fence. Secure the stop (J) in place with a
handle (K).
5. Slide clamp bar (L) into the bracket, and miter
gauge. Tighten setscrew found in the bracket.
Pull up on the quick release (M) and slide the
clamp on to the bar. Position clamp disc
against the workpiece and pull the clamp lever
(N) towards you.
6. Use a square to make sure miter gauge is 90°
to saw blade. If you need to make an
adjustment. Loosen hex nut (O) found on
indicator bar and turn bolt (P) until it rests
against the miter gauge. Tighten the nut.
Adjust cursor if necessary.
7. Use a combination square to make sure miter
gauge is 45° to the saw blade. If you need to
make an adjustment. Loosen hex nut (Q)
found on the indicator bar and turn bolt (R)
until it rests against the miter gauge. Tighten
the nut. Adjust cursor if necessary.
Figure 14
14
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.