Jet EQUIPMENT &TOOLS SBR-30N, SBR-40N Owner's Manual

.JET

EQUIPMENT& TOOLS

OWNER'S MANUAL

SBR-30N 1-40NShear, Brake, and Roll

.

.

,j,J

~ ..ar.............

Ifill.,T -'" -.-.

~ ..'-" ,.,./1";'1"

.-' --'

~

JET EQUIPMENT &TOOLS, INC.

A WMH - Walter Meier Holding Company

(SBR-30N shown)

P.o. BOX1349
Auburn,WA98071-1349

253-351-6000
Fax [phone]

No. M-754031 06/01

Important Information

1-YEAR

LIMITED WARRANTY

JET offers a one-year limited
warranty on this product

REPLACEMENT PARTS

Replacement parts for this tool are available directlyform JET Equipment& Tools.
To place an order, call 1-800-274-6848. Please have the following information ready:

1. Visa, MasterCard, or DiscoverCardnumber

2. Expirationdate

3. Part number listedwithin this manual

4. Shipping address other than a PostOfficebox.

REPLACEMENT PART WARRANTY

0

JET Equipment & Tools makes every effort to assure that parts meet high quality and durability
standards and warrants to the original retail consumer/purchaser of our parts that each such
part(s) to be free from defects in materials and workmanship for a period of thirty (30) days from
the date of purchase.

PROOF OF PURCHASE

Please retain your dated sales receiptas proof of purchase to validate the warranty period.

LIMITED TOOL AND EQUIPMENTWARRANTY

JET makes every effort to assure that its products meet high quality and durability standards and warrants
to the original retail consumer/purchaser of our products that each product be free from defects in materials
and workmanship asfollows: 1YEAR LIMITED WARRANTY ON THIS JET PRODUCT. Warranty does not
apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations

outside our facilities or to a lack of maintenance. JET LIMITS ALL IMPLIED WARRANTIES TO THE
PERIOD SPECIFIED ABOVE FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL.
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MECHANTABILITY AND FITNESSARE

EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JET SHALL IN NO

EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERY OR FOR INCIDENTAL,
CONTINGENT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU. To take advantage of this warranty, the product or part must be returned for examination, postage
prepaid, to an authorized service station designated by our Auburn office. Proof of purchase date and an

explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, JET
will either repair or replace the product or refund the purchase price, if we cannot readily and quickly
provide a repair or replacement, if you are willing to accept such refund. JET will return repaired product or
replacement at JET's expense, but if it is determined there is no defect, or that the defect resulted from
causes not within the scope of JET's warranty, then the user must bear the cost of storing and returning the
product. This warranty gives you specific legal rights, and you have other rights, which vary, from state to

state.

JET Equipment &Tools. P.O. Box 1349,Auburn, WA 98071-1349 . [phone]

&WARNING

.

Read and understand the entire instruction manual before attempting assembly or
operation.

.

This shear, brake, and roll is designed and intended for use by properly trained and
experienced personnel only. Ifyou are not familiar with the proper and safe operation
of a shear, brake, and roll, do not use until proper training and knowledge have been

obtained.

.

This shear, brake, and rollis intended to be used by one person only.

.

The shear, brake and rollmust be bolted securely to a stand and the stand bolted securely

to the floor. Ifthe machineisto be bench mounted,the bench must be able to support the

weight of the machine and must be boltedto the floor.

.

Keepthe floor around the shear, brake, and roll clear of scraps, debris, oil, and grease. The

flooring around the machineshould be a non-skidtype.

.

Sheet metal stock has sharp edges. To prevent cuts, use caution when handling.

.

Keep hands and fingers clear of the area in front and rear of the shearing blades.

.

Keep guards in place when not using the slip roll.

.

Keepother people away from the shear, brake,and roll.

.

Keep hands and fingers clear of the slip roll "nip" points. Keep hand and fingers away from
the area in front and rear of the shearblades.

.

Keep hands and fingers away from the press brakedieswhen forming metal.

.

Do not exceed the maximum capacity of the machine.

.

Do not use the machinefor any purpose other than for which it is designed.

.

Failure to comply with all of these warnings may cause serious injury.

.

SOME DUST CREATED BY power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

Lead from lead based paint
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically"treated lumber.

.
.

.

YOUR RISK FROM THOSE EXPOSURES varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals:work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specifically designed to filter out microscopic
particles

- 1 -

Specifications:

SBR-30N

Stock Number 754031
Capacity (Mild Steel):

Shearing 20 Ga.x30"
Bending ..20 Ga.x30"

Rolling 20 Ga.x30"
Size of Slip Roll 1-1/2"Wx30"L
Width of Upper Dies ' """""""""""""" 1",2",3",6",8", & 10"

Upper Die Height

..'" ... . " 4-3/8"

Minimum Forming Radius 3/4"

Overall Dimensions ... '... ... ... 42-1/2"Lx21-1/2"Wx28"H

Shipping Weight (approx.) ""'''''''''''' 330 Ibs.

Specifications:

SBR-40N

Stock Number..........................

Capacity (Mild Steel):
Shearing.. """ ... ".. 20 Ga.x40"

Bending ' , " 20 Ga.x40"

Rolling , 20 Ga.x40"
Size of Slip Roll 1-1/2"Wx40"L

Width of Upper Dies 1",1-1/2", 2", 2-1/2", 4",7",10", & 15"

Upper Die Height .4-3/8"
Minimum Forming Radius 3/4"
Overall Dimensions 57"L x 19"W x 34"H

Shipping Weight (approx.) .616 Ibs.

'" 754041

The specifications in this manualare givenas general informationand are not binding. JET

Equipment and Tools reserves the right to effect, at any time andwithout prior notice, changes or
alterations to parts,fittings, and accessory equipment deemed necessary for any reason

whatsoever.

- 2 -

Assembly

1. Finish removing the crate from around the
machine.

2. Removethe bolts holding the machineto the
skid.

3. Carefully clean all rust protected surfaces with a
mild solvent or kerosene and a soft rag. Do not
use lacquer thinner, paint thinner, or gasoline.

These will damage paintedsurfaces.

4. Coat all machinedsurfaceswith a very light film

of oil to inhibit rust.

5. Carefully move the shear, brake, and roll to a

work benchor stand. Machine location must
allow free access on all sides.

6. Boltthe machine to a stand or a workbench. If
using a stand, the stand must be bolted to the

floor. If using a work bench, the benchmust be
bolted to the floor.

7. Remove one handle (A, Fig. 1)fromthe handle
assembly.

8. Loosen wing lock (B, Fig. 1).

9. Slide bar (C, Fig. 1)into hub and tighten wing
lock (Fig. 1)to hold in place.

10. Replace handle (B. Fig. 1).

11. Back gauge assembly is installed in either the

shear position (angle iron faces up- Fig.2) or
the brake position (angle iron faces down - Fig.

3).

Lubrication

1. Grease nipples on top of leftand right frame

sides with #2 lithiumtube grease once a month
(0, Fig. 1).

- 3 -

A

t

Fig.1

Fig. 2

Fig. 3