JCD2006
MOBILE CD PLAYER / RECEIVER
Installation and Operation Manual
CD PLAYER / RECEIVER
40 WATTS X 4 |
JCD2006 |
AS PS |
RDM RPT INT |
CH |
|
-IN |
|
|
CD |
|
|
SAFETY INFORMATION
When Driving
Keep the volume level Iow enough to be aware of the road and traffic conditions.
When Washing your Vehicle
Do not expose the product to water or excessive moisture. Moisture can cause electrical shorts, fire or other damage.
When Parked
Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback.
Use the Proper Power Supply
This product is designed to operate with a 12 volt DC negative ground battery system.
Protect the Disc Mechanism
Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit.
CAUTION:
THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/ INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY. BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. PLEASE REFER SERVICING TO A QUALIFIED TECHNICIAN.
WARNING:
•TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
•TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
•THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
JCD2006
DISC NOTES
Compatible Disc Types
Table 1: General Disc Information
Disc Type |
|
Logo |
|
Diameter/ |
Playback Time |
|
|
|
Playable Sides |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Audio CD |
|
|
|
|
12 cm single side |
74 minutes |
|
|
|
|
REWRITABLE |
|
|
|
|
RECORDABLE |
|
|
|
|
|
|
|
|
|
|
|
NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and the CD is finalized.
Disc Maintenance
•A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge. Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.
|
|
|
|
|
|
|
|
|
|
Insert label |
Do not bend. |
Never touch |
Wipe clean from |
|
side up. |
|
|
the under side |
the center to the |
|
|
|
of the disc. |
edge. |
|
|
|
|
|
•Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.
•Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers.
•Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle.
NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player.
2
JCD2006
INSTALLATION |
|
7. |
After completing the wiring connections, attach the front panel and turn the unit on to |
|||||
Before You Begin |
|
|
confirm operation (vehicle ignition switch must be on). If the unit does not operate, |
|||||
|
|
recheck all wiring until the problem is corrected. Once proper operation is achieved, turn |
||||||
1. |
Disconnect Battery |
|
|
the ignition switch off and proceed with final mounting of the chassis. |
||||
|
Before you begin, always disconnect the battery negative terminal. |
8. |
Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is |
|||||
2. |
Remove Transport Screws |
|
9. |
fully seated and the spring clips lock it into place. |
||||
Important Notes |
|
Attach one end of the |
|
|
||||
|
|
perforated support strap |
|
Dashboard |
||||
• |
Before final installation, test the wiring connections to make sure the unit is connected |
|
(supplied) to the screw stud on |
|
Support Strap |
|||
|
properly and the system works. |
|
|
the rear of the chassis using |
|
|||
|
|
|
|
|
||||
• |
Use only the parts included with the unit to ensure proper installation. The use of |
|
the hex nut and spring washer |
Plain Washer |
||||
|
unauthorized parts can cause malfunctions. |
|
|
provided. Fasten the other end |
Screw (5 x 25mm) |
|||
• |
Consult with your nearest dealer if installation requires the drilling of holes or other |
|
of the perforated strap to a |
|||||
|
|
|
||||||
|
modifications to your vehicle. |
|
|
secure part of the dashboard |
|
Screw Stud |
||
• |
Install the unit where it does not interfere with driving and cannot injure passengers if |
|
either above or below the radio |
Hex Nut (5mm) |
||||
|
|
|
||||||
|
there is a sudden or emergency stop. |
|
|
using the screw and plain |
Spring Washer |
|||
• |
If the installation angle exceeds 30º from horizontal, the unit might not give optimum |
|
washer provided. Bend the |
|
|
|||
|
performance. |
|
|
|
strap, as necessary, to position |
|
|
|
• |
Avoid installing the unit where it will be subject to high temperatures from direct sunlight, |
|
it. CAUTION: The rear of the |
|
|
|||
|
hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration. |
|
radio must be supported with |
|
|
|||
• |
Be sure to remove the control panel before installing the unit. |
|
the strap to prevent damage to |
|
|
|||
DIN Front/Rear Mount |
|
|
the dashboard from the weight |
|
|
|||
|
|
of the radio or improper operation due to vibration. |
||||||
This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear” |
10. |
Re-attach the front panel to the chassis and test radio operation by referring to the |
||||||
(DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis) |
|
operating instructions for the unit. |
|
|
||||
mount. For details, refer to installation methods A and B. |
Removing the Unit |
|
|
|||||
DIN Front Mount (Method A) |
|
To remove the radio after installation: |
|
Dashboard |
||||
1. |
Detach the front panel, if it is attached, by |
Dashboard |
1. |
Insert fingers into the groove in the front of |
|
|||
|
pressing the |
(release) button. |
|
|||||
|
|
|
frame and pull out to remove the frame. |
|
||||
|
Remove the DCP. |
|
Bend Tabs |
|
|
|||
|
|
|
(When re-attaching the frame, point the |
|
||||
2. |
Slide the mounting sleeve off of the |
182 |
|
|
||||
|
|
side with a groove downwards and re- |
|
|||||
|
chassis if it has not already been removed. |
|
|
|
||||
|
53 |
|
attach.) |
|
|
|||
|
If it is locked into position, use the removal |
|
|
|
|
|||
|
Screw Stud |
2. |
Insert the removal keys straight back until |
|
||||
|
keys (supplied) to disengage it. The |
|
|
they click, and then pull the radio out. If |
|
|||
|
removal keys are depicted in “Removing |
|
|
|
||||
|
|
|
removal keys are inserted at an angle, |
|
||||
|
the Unit” on page 3. |
|
|
|
Removal Key |
|||
|
|
|
|
they will not lock properly to release the |
||||
3. |
Check the dashboard opening size by |
|
|
|
||||
|
|
unit. |
|
|
||||
|
sliding the mounting sleeve into it. If the |
|
|
|
|
|||
|
|
Trim Plate Installation |
|
|
||||
|
opening is not large enough, carefully cut |
|
|
|
||||
|
|
Push the trim plate against the chassis until it is |
|
|||||
|
or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve |
|
||||||
|
fitted. You must do this before you install the |
|
||||||
|
into the opening or cause it to bend or bow. Check that there will be sufficient space |
|
||||||
|
behind the dashboard for the radio chassis. |
|
control panel, otherwise it can't be attached. |
|
||||
4. |
Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. |
DIN Rear Mount (Method B) |
|
|||||
|
With the sleeve fully inserted into the dashboard opening, bend as many of the tabs |
This unit has threaded holes in the chassis side panels which may be used with the original |
||||||
|
outward as necessary to firmly secure the sleeve to the dashboard. |
|||||||
|
factory mounting brackets of some vehicles to mount the radio to the dashboard. Please |
|||||||
5. |
Place the radio in front of the dashboard opening so the wiring can be brought through the |
|||||||
consult with your local mobile stereo shop for assistance on this type of installation. |
||||||||
|
mounting sleeve. |
|
|
|||||
|
|
|
1. |
Remove the existing factory radio from the dashboard or center console mounting. Save |
||||
6. |
Follow the wiring diagram carefully and make certain all connections are secure and |
|||||||
|
insulated with crimp connectors or electrical tape to ensure proper operation. |
|
all hardware and brackets as they will be used to mount the new radio. |
3