www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600
|
|
This Data Sheet Includes Information On |
|
|
|
|
Jenn-Air |
|
|
• |
Product Model Number (s): |
• |
||
|
|
Free Standing Gas Ranges: |
|
|
|
J31111WAV, J31111XAW, J31111XAV, J32111WAV, |
|||
|
|
J32111XAW, J32111XAV, J31213WAV, J31213XAW |
|
|
|
|
and J31213XAV |
|
|
• |
Dimensions (Actual Size) |
• |
||
|
|
Height of cooking surface: 36" |
|
|
|
|
Height overall: |
44 7/8" |
|
|
|
Case width: |
30" |
|
|
|
Depth NOT including handle: |
26 5/32 |
|
|
|
Door swing: |
20" |
|
|
|
Height at full leg adjustment: |
36" |
|
|
|
Height at 0" leg adjustment: |
35 1/2" |
|
|
• |
Additional Information |
• |
•Units depth including door handle is 28 3/8".
•Can be installed with the back against (0") a vertical combustible wall, and the sides below the cooktop surface against (0") combustible base cabinets.
•Electrical requirements: 120 VAC,60Hz. 15 amp grounded circuit protection is required.
•Gas requirements: 1/2" NPT female inlet. Line MUST have an accessible shut off valve when range is installed. Can be converted to LP gas without additional parts.
•Proper operation requires use of range hood.
•Cabinetry over cooktop : 30' minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet. 24" minimum when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or copper.
•To eliminate the hazard of reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the hazard can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets.
•For Free-standing installations the cutout opening width is 30" ± 1/16" minimum. The height of the countertop is 36" and countertop depth is 25".
•Island or peninsula installations with 24" deep base cabinets must use flush back (no rear toe space) cabinets to avoid range interference,. If rear toe space is desired, use 27" or deeper cabinets.
•J31111WAV, J32111WAV and J31213WAV : Designer White.
•J31111XAW, J32111XAW and J31213XAW : White.
•J31111XAA, J32111XAA and J31213XAA : Almond
Subject to change without notice. This system is designed to |
|
be updated daily if necessary. Dimension Express is not |
|
responsible for use of superseded, voided, or outdated data |
|
sheets. Because of the difficulty or impracticability of deter- |
|
mining actual damages, liability of Dimension Express shall |
|
not exceed $50.00. |
|
Copyright © Dimension Express, 2000. |
255 |
30"
(not to scale)
44 7/8"
36"
20"
Door open
26 5/32
|
Wall View |
|
|
(not to scale) |
|
|
1" |
|
Locate gas line |
|
|
within shadded |
28" |
|
area |
||
|
||
|
Electric |
|
18" |
Location |
|
|
Gas Location |
Locate electrical supply outlet (flush with wall) within hashed area. Area is 13" W X 9" H. located 9 3/8" above floor and 1 1/2" from right wall.
2 1/2"
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wall View |
|
|
|
|
|
|
|
|
|
||||||||
(not to scale) |
|
|
|
|
|
|
|||||||||||
30" |
Min. |
|
|||||||||||||||
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
30" |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18" |
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
36" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
Range |
|
|||||||
Countertop |
|
|
|
|
|
|
|||||||||||
height |
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Upper cabinets
can only be 13" deep maximum. Over range cabinet is NOT recommended.
Side clearance from cooktop to 18" above the cooktop is 3" on each side (see
solid arera)
30" Minimum cutout width
• NEVER reuse Data Sheets. Data Sheets are subject to change without |
• Call Dimension Express if you have any questions at (775) 833-3633 • |
notice. Dimension Express is a FREE service bureau and is updated daily, |
• Always refer to a current Code at a Glance or manufacturer directory • |
it makes far more sense to spend the time necessary to request new Data |
• Data Sheet codes change on the first of odd numbered months at 12:01am • |
Sheets for each project, as opposed to the problems, time, costs, and risks |
BN220.7 • A255 • 31469 • 002906 • 193313 • 67213 |
associated with reusing old Data Sheets. |