Jenn-Air CARBON18L, COGNAC30L, CAVIAR24L, JKCPR301GL, JKCPR241GL Use & Care Guide

USE A D CARE GUIDE

COLUMN REFRIGERATION

GUIDE DˈUTILISATION ET DˈENTRETIEN

RÉFRIGÉRATION COLONNE

W10918236B

INTRODUCTION

SAFETY

Your safety and the safety of others are very important.

many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

safety alert symbol.

alerts you to potential hazards that can kill or hurt you and others.

messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” mean:

		You can be killed or seriously injured if you don't immediately follow instructions.
	DANGER
		You can be killed or seriously injured if you don't follow instructions.
	WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of shock, or injury when using your refrigerator, follow these basic precautions:

To avoid a hazard due to instability of the with the instructions.

Installation shall be performed only by manufacturer, or an authorized agent.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Disconnect power to all units before servicing.

If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent

a hazard.

Replace all parts and panels before operating.

Remove doors from your old refrigerator.

Connect to a potable water supply only.

Use

Kemmable materials and vapors, such as gasoline, away from refrigerator.

Do not store explosive substances such as this refrigerator.

Use two or more people to move and install refrigerator.

Disconnect power before installing ice maker (on ice maker kit ready models only).

Use a sturdy glass when dispensing ice (on some models).

Do not hit the refrigerator glass doors (on some models).

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This refrigerator is intended to be used in household and similar applications such as:

working environments

–farm houses and by clients in hotels, motels, and other residential type environments

–bed and breakfast type environments

–catering and similar non-retail applications

SAVE THESE INSTRUCTIONS

<![if ! IE]>

<![endif]>INTRODUCTION

INTRODUCTION | 3

INTRODUCTION

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

WARNING

Suffocation Hazard Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Do your part to prevent accidental child entrapment and suffocation by properly disposing of your old refrigerator or freezer.

BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER:

Take off the doors.

Leave the shelves in place so children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certi ed refrigerant technician in accordance with established procedures.

4 | INTRODUCTION

INTRODUCTION

REGISTERING YOUR APPLIANCE

Gain access to our concierge-level Customer Support by registering your appliance.

We make product registration simple and straightforward so you can start using your exclusive JennAir benefits today.

Registering your appliance allows you to:

■■ Streamline your warranty service

If we have your appliance information, we can help you faster.

■■ Protect your purchase

In case of an insurance loss—such as fire, flood, or theft—your product registration could serve as a proof of purchase.

■■ Keep your family safe

We’ll notify you in the rare case of a safety notification.

Start taking advantage of these benefits today

by going online to register your appliance at https://register.jennair.com.

PRODUCT IDENTIFICATION

Your product identification, which includes the model and serial numbers, is listed on the

product rating plate.

Recording this information below allows us to assist you more easily if your appliance should ever require service from one of our JennAir® Authorized Service Providers.

Model Number:_______________________________

Serial Number:________________________________

Date of Installation: _ _________________________

Authorized Dealer: ___________________________

Authorized Dealer Phone #: __________________

TABLE OF CONTENTS
INTRODUCTION
Safety .............................................................................	3
Proper Disposal of
Your Old Refrigerator .........................................	4
Registering Your Appliance.............................	5
Product Identification.........................................	5
Product Features....................................................	6
Refrigerator Controls...........................................	8
Freezer Controls.......................................................	10
GETTING STARTED
Before Use...................................................................	12
Smart Features.........................................................	12
Smart Grid...................................................................	13
Automatic Setup (WPS).....................................	14
Manual Setup (First-Time Use)......................	16
Shelves...........................................................................	17
Deli/Crisper Drawers.............................................	17
CARE AND CLEANING
Cleaning........................................................................	18
Leather Panel Care................................................	18
Vacation Care............................................................	19
Power Interruptions..............................................	19
Replacing The Water Filter...............................	20
TROUBLESHOOTING
Operation.....................................................................	22
Temperature And Moisture.............................	23
Ice And Water............................................................	23
Lights...............................................................................	24
ASSISTANCE
Contact..........................................................................	25
In The U.S.A.................................................................	25
In Canada.....................................................................	25
Accessories..................................................................	25
Connected Appliance
Regulatory Notices................................................	26
Performance Data Sheet..................................	28
Warranty.......................................................................	30
TABLE DES MATIÈRES.................	35

<![if ! IE]>

<![endif]>INTRODUCTION

INTRODUCTION | 5

INTRODUCTION
		PRODUCT FEATURES
14.		1.	Fully Integrated and Flush
	1.		Design with Articulating Hinge
			Creates an integrated appearance with
			custom cabinets without exposed hinges or
			trim pieces.
13.	2.	2.	Adjustable Aluminum and
			Glass Door Bins
			Make it easy to customize storage
12.			according to your preferences, providing
			quick access to frequently used items.
	3.		Refrigerator and freezer door bins can be
			positioned to accommodate a variety of
11.			container sizes.
		3.
			Custom Overlay Design
			Ships with factory-installed doors. To create
10.			a finished refrigerator, customers must
			purchase either custom overlay panels and
			handles from a cabinet manufacturer, or a
9.			JennAir® suite-coordinating panel kit.
		4.	Obsidian Interior
8.	4.		Showcases food items throughout the
			refrigerator or freezer, and provides a
			sharper contrast than white interiors.
7.		5.	90°/115° Door Stop Position
			Provides options to ensure ample clearance
			between the open door and adjacent
			cabinetry.
	5.	6.	Wi-Fi Connectivity
			This refrigerator can connect with in-home
			Wi-Fi to provide remote control through
6.			the JennAir® App, available to download for
			use with either iOS or Android devices.
6 | INTRODUCTION

INTRODUCTION

7. Soft, Auto-Close Crisper Drawers

Provide smooth operation by rolling open even when fully loaded, and feature an innovative auto-close design that pulls the drawer closed.

8.Electronic TemperatureControlled Crisper Drawer

(Refrigerator)

Drawer slides open effortlessly, even when fully loaded, with soft, self-close glides.

Two temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

Produce: 39°F (3.9°C)

Assorted: 37°F (2.8°C)

9.Capacitive Touch Controls with LED Display

The touch panel houses the control menu and function controls. The touch keypads are very sensitive and only require a light touch. The controls are located in the midsection of each column for easy access.

†®NSF is a registered trademark of NSF International.

10.Electronic TemperatureControlled Deli Drawer

(Refrigerator)

Deli slides open effortlessly, even when fully loaded, with soft, self-close glides.

Five temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

Produce: 39°F (3.9°C)

Assorted: 37°F (2.8°C)

Beverage: 34°F (1°C)

Deli: 33°F (0.6°C)

Meat: 32°F (0°C)

Electronic TemperatureControlled Deli Drawer (Freezer)

Three temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

Assorted: 0°F (-17.8°C)

Spirits: -2°F (-18.9°C)

DeepFreeze: -8°F (-22.2°C)

11.Water Dispenser (Refrigerator)

Allows you to dispense filtered water.

<![if ! IE]>

<![endif]>INTRODUCTION

12. Interior Perimeter LED Theater Lighting

Perimeter LED lighting elegantly ramps up to full brightness when the door or interior drawers are opened, increasing visibility by minimizing shadows caused by top lighting. Selecting a cooling zone on the control panel causes the lighting in the same zone to pulse.

13. Adjustable Clear Glass Shelves

Tint-free, clear glass shelves that offer an open, refined look that makes food and beverages easy to see and locate. Glass shelves complement the LED lighting for exceptional clarity that allows more light to fill the interior.

14. EveryDrop® Filter

EveryDrop® water filters are NSF®† certified to reduce most contaminants, including chlorine taste and odor, lead, pesticides, and trace amounts of pharmaceuticals. EveryDrop® brand filters are the only filters tested and certified for your refrigerator system. Replace your EveryDrop® filter every 6 months for maximum contaminant reduction.

15. Automatic Ice Maker (Freezer)

Ensures a continuous supply of fresh ice cubes made from filtered water.

INTRODUCTION | 7

INTRODUCTION

REFRIGERATOR CONTROLS

1.

Viewing and Adjusting

Temperature

When you first install your

refrigerator, make sure that

the control is still set to the

1.

2.

3.

4.

5.

6.

recommended setting. The

factory-recommended

temperature is 37°F (3°C).

Touch - or + to select a

temperature seting. Press and hold - and

+ to change display from Fahrenheit to

Celsius.

2. Activate Temperature Mode for

Refrigerator Deli Drawer

Touch Assorted, Beverage,

Deli, Meat, or Produce to

select a zone temperature

setting.

3.

Cooling Zones

Select features of your refrigerator are tied

7.

8.

to the perimeter lighting.

Press a zone key to light the corresponding zone in your refrigerator.

8 | INTRODUCTION

INTRODUCTION

4. Max Cool

The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm

room temperatures. Press MAX COOL to activate Max Cool. After the Max Cool cycle completes, the refrigerator will return to its previous setting.

5. Connect

Wi-Fi connectivity allows your Smart Refrigerator to connect to the Internet and interact with the JennAir® App from

your smartphone or mobile device. See the “Automatic Setup—Wi-Fi Protected Setup (WPS)” section for more information.

Sabbath

Allows the door of the refrigerator to be opened or closed during the Sabbath or other religious holidays

without activating the interior lights or controls. Press and hold Sabbath for

3 seconds to activate Sabbath mode.

Lock

The control panel can be locked for easy cleaning or to avoid unintentional mode changes.

6. Power Outage

The Power Outage indicator lets you know if the power

supply to the refrigerator has been off and the temperature has risen.

Over temp Alarm

Helps avoid food spoilage and high energy costs by

sounding an alert when refrigerator temperatures remain at unusually high levels.

Door Open

The Door Open alarm feature sounds an alarm when the

refrigerator door(s) or freezer door is open for 5 minutes

and cooling is turned on. The alarm will repeat every 2 minutes. Close the door to turn the alarm and “Door Open” alert off. To stop the alarm noise with the door open, press any key.

7. Showroom

This mode is used when the refrigerator is on display in a retail store or if you want to

turn the cooling off and deactivate all other functions except interior

lighting.

To activate showroom mode, press and hold top and bottom zone

icons simultaneously for 3 seconds.

To deactivate the showroom mode, press and hold top and bottom

zone icons simultaneously for 3 seconds.

<![if ! IE]>

<![endif]>INTRODUCTION

8. Filter Reset

Displays the status of the water filter. To reset the filter, press and hold FILTER RESET for 3 seconds. After

countdown, the “Replace Filter” indicator will turn off.

Replace Filter

Replace the water filter. While you are dispensing

water, the “Replace Filter” icon will flash constantly

from beginning to the end of dispensing. After 14 days without replacing the water filter, the “Replace Filter” icon will blink seven times and an alert tone will sound three times at the end of dispensing. See the “Water Filtration System” section. NOTE: “Replace Filter” will remain illuminated if a filter reset is not completed.

Order Filter

Order a replacement water filter.

INTRODUCTION | 9

INTRODUCTION

FREEZER CONTROLS

1. Pure Freeze® Feature

Pure Freeze® feature is

activated automatically when

the freezer is at its lowest

setting. The Pure Freeze® setting reduces

freezer burn.

1.

2.

3.

4.

5.

6.

Viewing and Adjusting

Temperature

When you first install your

freezer, make sure that

the control is still set to the

recommended temperature.

The factory recommended

setting is -2°F (19°C) for the

freezer.

Touch - or + to select a temperature setting.

2. Activate Temperature Mode for

Freezer Deli Drawer

Touch Assorted, Spirits, or

DeepFreeze to select a zone

7.

8.

temperature setting.

3. Cooling Zones

Select features of your freezer are tied to the perimeter lighting. Press the zone keys to light the

corresponding zones in your freezer.

10 | INTRODUCTION

INTRODUCTION

4. Max Ice

The Max Ice Setting increases the freezer cooling capacity improving the ice making rate.

Ice Maker Off

To turn the ice maker off, touch ICE MAKER OFF.

5. Connect

Wi-Fi connectivity allows your Smart Freezer to connect

to the Internet and interact with the JennAir® App from

your smartphone or mobile device. See the “Automatic Setup—Wi-Fi Protected Setup (WPS)” section for more information.

Sabbath

Allows the door of the freezer to be opened or closed during the Sabbath or other religious holidays without

activating the interior lights or controls. Press and hold Sabbath for 3 seconds to activate Sabbath mode.

Lock

The dispenser can be locked for easy cleaning or to avoid unintentional dispensing.

6. Power Outage

The Power Outage indicator lets you know if the power

supply to the freezer has been off and the freezer temperature has risen.

Over temp Alarm

Helps avoid food spoilage and high energy costs by

sounding an alert when freezer temperatures remain at unusually high levels.

Door Open

The Door Open alarm feature sounds an alarm when the

refrigerator door(s) or freezer door is open for 5 minutes

and cooling is turned on. The alarm will repeat every 2 minutes. Close the door to turn the alarm and “Door Open” alert off. To stop the alarm noise with the door open, press any key.

7. Showroom

This mode is used when the freezer is on display in a retail

store or if you want to turn the cooling off and

deactivate all other functions except interior lighting.

To activate showroom mode, press and hold top and bottom zone icons

simultaneously for 3 seconds.

To deactivate the showroom mode, press and hold top and bottom zone icons simultaneously for 3 seconds.

<![if ! IE]>

<![endif]>INTRODUCTION

8. Filter Reset

Displays the status of the water filter. To reset the filter, press and hold FILTER RESET for 3 seconds. After

countdown, the “Replace Filter” indicator will turn off.

Replace Filter

Replace the water filter. While you are dispensing

water, the “Replace Filter” icon will flash constantly from

beginning to the end of dispensing. After 14 days without replacing the water filter, the “Replace Filter” icon will blink seven times and an alert tone will sound three times

at the end of dispensing. See the “Water Filtration System” section.

NOTE: “Replace Filter” will remain illuminated if a filter reset is not completed.

Order Filter

Order a replacement water filter.

INTRODUCTION | 11

GETTING STARTED

BEFORE USE

Before using your refrigerator, all packaging materials should be removed and the interior should be cleaned.

Remove tape and glue residue from surfaces before turning on the refrigerator. With your fingers, rub a small amount of liquid dish soap over any adhesive and wipe with warm water to remove.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These can damage the surfaces of your refrigerator.

Dispose of and/or recycle all packaging materials.

After all packaging materials have been removed, clean the inside of your refrigerator.

Flush 3 gallons (11.4 L) of water through the water system to clear air from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser flow.

NOTE: If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the water filter housing to leak.

SMART FEATURES

Smart Features help make your every day a little more efficient by letting you remotely monitor, manage, and maintain your refrigerator.

REMOTE TEMPERATURE CONTROL

What it does: Allows you to control the temperature of your refrigerator remotely from your mobile device via the JennAir® App.

What it does for you: Lets you control temperatures in your refrigerator, freezer, and temp-controlled pantry remotely—not just when you are standing in front of it.

WATER FILTER STATUS

What it does: Gives you a look at the life remaining for your air and water filters before a replacement is needed.

What it does for you: Helps you be more efficient in planning for, ordering, and replacing filters.

AUTO REORDER

What it does: Allows you to order replacement filters, consumables, and accessories via the JennAir® App for delivery directly to your home.

What it does for you: Simplifies ordering correct water and air filters—no trips to the store and searching for the correct filters.

OVER TEMPERATURE

What it does: Sends you a notification when the temperature in your refrigerator reaches and rises above a specified value in the refrigerator and freezer compartments.

What it does for you: Alerts you to overtemperature status to provide input regarding disposition of refrigerator/freezer contents.

MAX COOL—REFRIGERATOR

What it does: Allows you to control your refrigerator remotely from your mobile device via the JennAir® App.

What it does for you: Lets you turn on/off Max Cool options remotely to make temperatures colder in the refrigerator in anticipation of loading newly purchased grocery items.

MAX ICE—FREEZER

What it does: Allows you to control your freezer remotely from your mobile device via the JennAir® App.

What it does for you: Makes fresh-tasting ice to accommodate your entertainment needs - up to 4 pounds in 24 hours.

PURE FREEZE® MODE

What it does: Allows you to receive status of your refrigerator remotely to your mobile device via the JennAir® App.

What it does for you: Indicates when temperatures are adjusted down to a deep freeze level to reduce freezer burn and helps frozen items maintain their appearance and taste.

12 | GETTING STARTED

GETTING STARTED

SMART FEATURES (CONT.)

SABBATH MODE

What it does: Allows the door of the refrigerator or freezer to be opened or closed during the Sabbath or other religious holidays without activating the interior lights or controls. Allows you to turn on and off remotely from your mobile device via the JennAir® App.

What it does for you: Lets you turn on/off Sabbath mode options remotely.

DOOR OPEN ALERT

What it does: Sends you a notification when the door of the appliance has been left open.

What it does for you: Alerts you to door ajar status so you can close the door(s) or call home to ask someone else to close the door before an over-temp situation arises.

POWER OUTAGE

What it does: Sends you a notification when power to your refrigerator goes out, returns, or highest temperature is reached.

What it does for you: Alerts you to power status and disposition of the appliance contents.

SMART GRID

This product has WiFi capability and requires Internet connectivity and a wireless router to enable interconnection with an Energy Management System, and/or with other external devices, systems, or applications.

<![if ! IE]>

<![endif]>STARTED GETTING

GETTING STARTED | 13

GETTING STARTED

AUTOMATIC SETUP—WI-FI PROTECTED SETUP (WPS)

YOU WILL NEED:

A home wireless router capable of WPS (Wi-Fi protected Setup). The router should be on and have a live internet connection.

To use this feature you need:

A smartphone running Android 4.3 (or higher) with a 1280x720 (or higher) screen or a tablet or a smartphone running iOS 8 (or higher).

A wireless router 2.4 Ghz Wi-Fi b/g/n connected to internet (verify with your smart device that the signal of your home wireless network is strong close to the appliance).

The Smart Appliance Identification Number (SAID) from your refrigerator. This is located on a sticker on the inside of the water filter door.

SAID: 0123456789 Contains FCC ID: A5UWICHIN01 MAC ID: 88:E7:12:XX:YY:ZZ Contains IC: 10248A-WICHIN01

NOTE: If your home wireless router is not equipped with a WPS button, please check the user manual of your router to confirm

if it is WPS capable. If not, alternate setup instructions are at www.jennair.com/connect.

1.Set up router

INTERNET

WI-FI PROTECTED

SETUP (WPS)

HOME WIRELESS

ROUTER

Press the WPS button on the router. An indicator light will begin blinking.

NOTE: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe, or you will need to reinitiate WPS.

2.Set up refrigeration appliance (time-sensitive step)

Press and hold CONNECT on the control panel for

3 seconds.

The Wi-Fi status indicator () on the appliance control

panel will blink slowly while your appliance and router

attempt to connect. If the connection is successful, the Wi-Fi status indicator will illuminate and remain lit.

IF YOUR APPLIANCE DOESN’T CONNECT:

If your appliance and router fail to connect after 2 minutes, the Wi-Fi status indicator will blink rapidly for 5 seconds and then turn off. Check any connection instructions for your specific

router, and refer to alternate instructions at www.jennair.com/connect.

NOTE: If this is your first smart appliance, you will need to download the JennAir® App and create an online user account.

If you already have the app and a user account, please skip ahead to Step 4, “Register your refrigerator in your user account.”

14 | GETTING STARTED

GETTING STARTED

AUTOMATIC SETUP—WI-FI PROTECTED SETUP (WPS) (CONT.)

DISCONNECT AND RECONNECT WI-FI

To disconnect Wi-Fi, press and the hold CONNECT for 7 to 15 seconds. The Wi-Fi status indicator will turn off, indicating that you have disabled Wi-Fi.

To reconnect Wi-Fi, press and hold CONNECT for 3 seconds on the control panel.

The Wi-Fi status indicator () on the appliance control panel will blink slowly while your appliance and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will illuminate and remain lit.

DISCONNECT AND RECONNECT ROUTER

To disconnect your refrigerator from your router, press and hold CONNECT for more than 15 seconds. The Wi-Fi indicator will turn off, indicating that your refrigerator is completely disconnected from Wi-Fi and your router.

To reconnect your appliance to your router and reconnect Wi-Fi, press and hold CONNECT for 3 seconds.

The Wi-Fi status indicator () on the appliance control panel will blink slowly while your refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will come on and remain lit.

Press the WPS button on the router. An indicator light will begin blinking.

NOTE: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe or you will need to reinitiate WPS.

3. Download JennAir® App and set up user	4. Register your refrigerator in your user
account	account
	<![if ! IE]> <![endif]>STARTEDGETTING

From your mobile device, smartphone, or tablet, go to www.jennair.com/connect and follow

the instructions to download and install the JennAir® App.

Once installed, tap the JennAir® App icon to open the app. You will be guided through the steps to set up a user account. The App will make sure to get the necessary personal and home information as well as information about your energy company.

Registering your refrigerator in your account is a necessary step in order for you to take full advantage of the Smart features. When prompted by the app, enter the SAID (casesensitive), which can be found on a sticker on the inside of the water filter door.

My Smart Appliance ID# is:

_________________________________________________

The Wi-Fi status indicator on the refrigerator control panel will blink slowly while your refrigerator and router attempt to connect.

NOTE: This blinking only applies to first-time registration after provisioning. Blinking will not occur for automatic reconnection after a connection is established.

Once you’ve connected your refrigerator to your home Wi-Fi network, it will remain linked even if the power goes out, you move the appliance, or if you put it in storage.

If you replace your wireless router or get a different Smart appliance, you will need to repeat this connectivity set-up process.

GETTING STARTED | 15

GETTING STARTED

MANUAL SETUP (FIRST-TIME USE)

— ACCESS POINT METHOD

This procedure uses Micro Access Point technology and is applicable if your router does not support WPS.

1.Before starting the Setup procedure, please take note of the home wireless network name (SSID), its password and the SAID of appliance. These will be required during the installation process.

2.Turn on your router and make sure the internet connection is working.

3.On your appliance, activate the provisioning process using the AP method. You

should see the Wi-Fi icon blinking on the appliance HMI.

4.Turn on your smart device (phone or tablet) and access your list of available wireless networks in the settings menu.

5.The appliance has created a wireless network (SSID). Select this network from the list of available wireless networks. The network name is made up of the prefix from your appliance type (e.g. washer, dryer, etc.) followed by the MAC address (ex. REFRID_88_E7_12_B3_66_ C3). If you don’t see it, you may need to refresh the list of networks or verify the Wi-Fi icon is on the appliance display.

6.Once you have selected the SSID, a password will be required. Use the SAID as a password (i.e., 444441ABCD).

NOTE: This password is case-sensitive.

7.Connect to the network.

8.Wait until your device is confirmed to be connected to the appliance Wi-Fi network.

9.Open a web browser. If nothing appears, type “192.168.10.1” in the address bar (URL) and press Enter. The browser displays a Smart web page. It is the configuration page of the Wi-Fi radio of your appliance.

10.In the drop-down list of available networks, select the name of your home wireless network.

11.If your home wireless network is hidden, select “Other” and manually enter its name (SSID) and security protocol.

WPA2

12.Enter the password for your home wireless network, if required, and submit. Remember, this kind of password is casesensitive.

13.Click the “” button to submit, and wait a few seconds.

14.The Wi-Fi icon on the appliance should stop blinking and turn on permanently once connected. Otherwise, disconnect and reconnect the appliance to the main power and repeat the procedure.

15.The Setup process is complete.

16 | GETTING STARTED

GETTING STARTED

SHELVES

The shelves in your appliance are adjustable to meet your individual storage needs.

Storing similar food items together in your appliance and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open and save energy.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-sized pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

TO REMOVE AND REPLACE THE SHELF AND SHELF SUPPORTS:

1.Remove the shelf by tilting it up at the front and lifting it out of the shelf supports. Pull the shelf straight out.

2.To replace the shelf, reposition the shelf supports in the desired location. Check that they are level and firmly inserted in the support rails.

DELI/CRISPER DRAWERS

TO REMOVE AND REPLACE THE DELI/CRISPER DRAWERS:

1.To remove the deli/crisper drawers, press the clips located at the bottom of the drawer.

2.Lift up on the drawer and pull straight out.

<![if ! IE]>

<![endif]>STARTED GETTING

3.

4.

Place the back of the shelf in the shelf supports.

Lower the front of the shelf and make sure that it is positioned correctly.

1.

2.

To replace the deli/crisper drawers, extend the glides to their fullest extent.

Using your fingers, hold the glides in place as you place the drawer back on the glides.

GETTING STARTED | 17

CARE AND CLEANING

CLEANING

Explosion Hazard

Failure to do so can result in death,

Below are the recommended steps to clean your appliance.

1.Press the power switch to OFF.

A.To access the power switch, remove the toe kick by pulling out to release it from the brackets.

2.Remove all removable parts (such as shelves and crispers) from the inside of the appliance.

3.Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum on plastic parts, interior, door liners, or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

To help remove odors, you can wash interior walls with a mixture of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).

4.Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners containing chlorine. Dry thoroughly with a soft cloth.

5.Press the power switch to ON.

6.To replace, press the toekick panel onto the toekick bracket to engage the gripping pads.

LEATHER PANEL CARE

Under normal usage conditions, regular dusting and vacuum cleaning in crevices or bottoms is all that is necessary to clean the leather panel.

For minor spots, wipe any excess liquid up immediately with a clean absorbent cloth or sponge. If necessary, use a lightly moistened cloth with clean lukewarm water and let dry naturally.

NOTE:

Using hairdryer for drying may damage leather panel, so do not dry using hairdryers.

Do not use saddle soap, cleaning solvents, furniture polish, oils, varnish, abrasive cleaners, detergent soaps, or ammonia on leather panel.

18 | CARE AND CLEANING

CARE AND CLEANING

VACATION CARE

1.Remove all food from the refrigerator/freezer.

2.Empty the ice bin.

3.Turn the power switch to Off.

A.To access the power switch, remove the toekick by pulling out to release it from the brackets.

B.To replace, press the toekick panel onto the toekick bracket to engage the gripping pads.

4.Clean refrigerator/freezer, wipe it, and dry well.

5.Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

POWER INTERRUPTIONS

If the power will be out for 24 hours or less, keep the door closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the following:

Remove all frozen food and store it in a frozen food locker.

Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

<![if ! IE]>

<![endif]>CLEANING AND CARE

CARE AND CLEANING | 19

CARE AND CLEANING

REPLACING THE WATER FILTER

The water filter should be replaced every 6 months based on a flow rate of

0.75 gpm-0.80 gpm (1.89- 2.27 Lpm) that filters 200 gallons (757 L) of water.

NOTE: If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the water filter housing to leak.

1.To open, push the water filter door up, which is located at the upper left above the refrigerator or freezer compartment.

2.Turn the water filter 90° counterclockwise to unlock.

3. Pull the filter out of the housing.

4.Remove the water filter cap from the water filter.

20 | CARE AND CLEANING