Jeep Compass 2016 Owner's Manual

0 (0)
Jeep Compass 2016 Owner's Manual

2 0 1 6 Compass

OW N E R ’ S M A N UA L

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you

have been drinking. Never drink and then drive.

Copyright © 2016 FCA US LLC

SECTION

TABLE OF CONTENTS

PAGE

1

INTRODUCTION . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . 3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . 9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 101

4

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 209

5

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 325

6

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 445

7

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 485

8

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 543

9

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 551

10

INDEX . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 563

1

2

3

4

5

6

7

8

9

10

 

INTRODUCTION

1

CONTENTS

 

 

 

 

INTRODUCTION . . . . . . . . . . . . . .

. . . . . . . . . .4

WARNINGS AND CAUTIONS . . . . . . . . . . . . . .

7

ROLLOVER WARNING . . . . . . . . .

. . . . . . . . . .4

VEHICLE IDENTIFICATION NUMBER . . . . . . . .

7

HOW TO USE THIS MANUAL . . . .

. . . . . . . . . .5

VEHICLE MODIFICATIONS/ALTERATIONS . . . .8

4 INTRODUCTION

INTRODUCTION

Congratulations on selecting your new FCA US LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold.

When it comes to service, remember that your authorized dealer knows your Jeep® vehicle best, has factory-trained technicians and genuine MOPAR® parts, and cares about your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle

control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Rollover Warning Label

INTRODUCTION 5

seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by 1 two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

6 INTRODUCTION

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also is stamped into the right front body, on the right front seat crossmember under the carpet and the vehicle registration and title.

INTRODUCTION 7

1

Vehicle Identification Number

8 INTRODUCTION

Right Front Body VIN Location

NOTE: It is illegal to remove or alter the VIN.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2

CONTENTS

A WORD ABOUT YOUR KEYS . . . . . . . . . . . .

.12

Ignition Key Removal . . . . . . . . . . . . . . . . . .

.12

Locking Doors With A Key . . . . . . . . . . . . . . .

14

Key Fob-In-Ignition Reminder . . . . . . . . . . . . .

14

SENTRY KEY . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Replacement Key Fobs . . . . . . . . . . . . . . . . . .

16

Customer Key Programming . . . . . . . . . . . . . .

17

General Information . . . . . . . . . . . . . . . . . . . .

18

VEHICLE SECURITY ALARM —

 

IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .

18

To Arm The System . . . . . . . . . . . . . . . . .

. . .18

Rearming The System . . . . . . . . . . . . . . . .

. . .19

To Disarm The System . . . . . . . . . . . . . . . .

. . .19

Vehicle Security Alarm Manual Override . . .

. . .20

REMOTE KEYLESS ENTRY — IF EQUIPPED

. . .20

To Unlock The Doors And Liftgate . . . . . . .

. . .20

Key Fob Unlock, Driver Door/All First Press

. . .21

Illuminated Approach — If Equipped . . . . .

. . .22

To Lock The Doors And Liftgate . . . . . . . . .

. . .22

Sound Horn With Key Fob Lock . . . . . . . . .

. . .22

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Flash Lights With Remote Key Lock/Unlock . .

.23

Using The Panic Alarm . . . . . . . . . . . . . . . . . .

24

Programming Additional Key Fobs . . . . . . . . . .

24

Key Fob Battery Replacement . . . . . . . . . . . . .

24

General Information . . . . . . . . . . . . . . . . . . . .

25

REMOTE STARTING SYSTEM —

 

IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .

26

How To Use Remote Start . . . . . . . . . . . . . . . .

26

Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

To Enter Remote Start . . . . . . . . . . . . . . . . . . .27

To Exit Remote Start Mode Without Driving

The Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .28

To Exit Remote Start Mode And Drive The

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.28

DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . .

.29

Manual Door Locks . . . . . . . . . . . . . . . . . . . . .

29

Power Door Locks . . . . . . . . . . . . . . . . . . . . .

30

Child-Protection Door Lock System —

 

Rear Doors . . . . . . . . . . . . . . . . . . . . . . . . . .

33

POWER WINDOWS — IF EQUIPPED . . . . . . . .

35

Power Window Switches . . . . . . . . . . . . . . . . .

35

Auto-Down . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Window Lockout Switch . . . . . . . . . . . . . . . . .

37

LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

OCCUPANT RESTRAINT SYSTEMS . . . . . . . . . .

39

Important Safety Precautions . . . . . . . . . . . . . .

40

Seat Belt Systems . . . . . . . . . . . . . . . . . . . . . .41

Supplemental Restraint System (SRS) . . . . . . . .60

Child Restraints . . . . . . . . . . . . . . . . . . . . . . .75

Transporting Pets . . . . . . . . . . . . . . . . . . . . . .95

ENGINE BREAK-IN RECOMMENDATIONS . . . .95

SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .96

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

Transporting Passengers. . . . . . . . . . . . . . . . .

.96

Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .

.97

 

2

Safety Checks You Should Make Inside The

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.98

Periodic Safety Checks You Should Make

 

Outside The Vehicle . . . . . . . . . . . . . . . . . . .

100

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate Remote Keyless Entry (RKE) Key Fobs. Ask your authorized dealer for these numbers and keep them in a safe place.

Ignition Key Removal

1.Place the gear selector in PARK (if equipped with an automatic transmission).

2.Place the ignition in the ACC (Accessory) position.

3.Push the key and cylinder inward and rotate the key to the LOCK position.

4.Remove the key from the ignition.

Key Fob

Ignition Positions

1 — LOCK

2 — ACC (ACCESSORY)

3 — ON/RUN

4 — START

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

NOTE: If you try to remove the key before you place the gear selector in PARK, the key may become trapped temporarily in the ignition. If this occurs, place the gear 2 selector in PARK, rotate the key clockwise slightly, and then remove the key as described above. If a malfunction occurs, the system will trap the key in the ignition to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.

WARNING!

Before exiting a vehicle, always shift the automatic transmission into PARK or the manual transmission into FIRST gear or REVERSE, apply the parking brake, turn the engine OFF, remove the key fob from the ignition and lock your vehicle.

(Continued)

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued)

Never leave children alone in a vehicle, or with access to an unlocked vehicle.

Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.

Do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.

CAUTION!

Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.

Locking Doors With A Key

You can insert the key with either side up. To lock the door, turn the key to the right. To unlock the door, turn the key to the left. Refer to ”Body Lubrication” in Maintenance Procedures” in “Maintaining Your Vehicle” for further information.

Key Fob-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition and the ignition position is LOCK or ACC sounds a signal to remind you to remove the key.

NOTE: With the driver’s door open and the key in the ignition, the power door locks will not lock, and key fob will not function.

SENTRY KEY

The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses Key Fobs that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.

NOTE: A Key Fob that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition or lock cylinder for that vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

During normal operation, after placing the ignition in the on position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on 2 after the bulb check, it indicates that there is a problem with the electronics. In addition, if the Vehicle Security Light begins to flash after the bulb check, it indicates that someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CAUTION!

The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Key Fobs

NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.

Duplication of Key Fobs may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.

NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle Key Fobs with you to an authorized dealer.

Customer Key Programming

If you have two valid Key Fobs, you can program new Key Fobs to the Sentry Key Immobilizer system by performing the following procedure:

1.Cut the additional Key(s) to match the ignition and lock cylinder key code.

2.Insert the first valid key into the ignition. Place the ignition in the ON/RUN position for at least three seconds, but no longer than 15 seconds. Then, place the ignition in the LOCK position and remove the first key.

3.Insert the second valid key into the ignition. Place the ignition in the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Place the ignition in the LOCK position and remove the second key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

4.Insert a blank key into the ignition. Place the ignition in the ON/RUN position within 60 seconds. After 10

seconds, a single chime will sound. In addition, the

2

Vehicle Security Light will stop flashing. To indicate

 

that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off.

The new key is programmed. The Key Fob will also be programmed during this procedure.

Repeat this procedure to program up to eight keys. If you do not have a programmed Key Fob, contact your authorized dealer for details.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: If a programmed Key Fob is lost, see your authorized dealer to have all remaining Key Fobs erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining Key Fobs must then be reprogrammed. All vehicle Key Fobs must be taken to an authorized dealer at the time of service to be reprogrammed.

General Information

The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

VEHICLE SECURITY ALARM — IF EQUIPPED

This Vehicle Security Alarm monitors the doors, liftgate, and ignition switch for unauthorized operation.

When the alarm is activated, the interior switches for door locks are disabled. The Vehicle Security Alarm provides both audio and visual signals, the horn will sound, the headlights, park lamps and/or turn signals will flash repeatedly for three minutes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the parking lights and tail lights will flash for an additional 15 minutes.

To Arm The System

1.Remove the key fob from the ignition and get out of the vehicle.

2.Lock the door using either the power door LOCK switch or the key fob LOCK button and close all doors.

3.The Vehicle Security Light in the instrument cluster will flash rapidly for approximately 16 seconds. This shows that the Vehicle Security Alarm is arming. During this period, if a door is opened, the ignition is placed in the ON/RUN position, or the power door locks are unlocked in any manner, the Vehicle Security Alarm will automatically disarm. After approximately 16 seconds, the Vehicle Security Light will flash slowly. This shows that the Vehicle Security Alarm is fully armed.

Rearming The System

If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

 

horn after three minutes, turn off all of the visual signals

 

after 15 minutes, and then the Vehicle Security Alarm will

 

rearm itself.

2

 

To Disarm The System

 

Push UNLOCK on the key fob, or insert the key into

 

the ignition and place the ignition in the ON/RUN

 

position.

 

If something has triggered the Vehicle Security Alarm in

 

your absence, the horn will sound three times, and

 

exterior lights blink three times when you unlock the

 

doors. Check the vehicle for tampering. The Vehicle

 

Security Alarm is designed to protect your vehicle.

 

However, you can create conditions where the Vehicle

 

Security Alarm will arm unexpectedly. If you remain in

 

the vehicle and lock the doors with the key fob, once the

 

Vehicle Security Alarm is armed (after 16 seconds), when

 

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

you pull the door handle to exit, the alarm will sound. If this occurs, push the UNLOCK button on the key fob to disarm the Vehicle Security Alarm.

Vehicle Security Alarm Manual Override

The Vehicle Security Alarm will not arm if you lock the doors using the manual door lock plunger.

REMOTE KEYLESS ENTRY — IF EQUIPPED

This system allows you to lock or unlock the doors and liftgate or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Key Fob. The Key Fob does not need to be pointed at the vehicle to activate the system.

Key Fob

NOTE: The line of transmission must not be blocked with metal objects.

To Unlock The Doors And Liftgate

Push and release the UNLOCK button on the key fob once to unlock the driver’s door or twice within five

seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

Key Fob Unlock, Driver Door/All First Press

This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the key fob. To change the current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Push and hold the LOCK button on a programmed key fob for at least 4 seconds but no

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

21

longer than 10 seconds. Then, push and hold the

UNLOCK

button while still holding

the

LOCK

button.

2

 

 

2.Release both buttons at the same time.

3.Test the feature while outside of the vehicle by pushing the LOCK/UNLOCK buttons on the key fob with the ignition in the LOCK position and the Key removed.

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pushing the LOCK button on the key fob while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Push the UNLOCK button to deactivate the Vehicle Security Alarm.

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Illuminated Approach — If Equipped

This feature activates the headlights for up to 90 seconds when the doors are unlocked with the Key Fob. The time for this feature is programmable on vehicles equipped with the EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually.

To Lock The Doors And Liftgate

Push and release the LOCK button on the Key Fob to lock all doors and liftgate. The turn signal lights will flash, and the horn will chirp to acknowledge the signal.

Sound Horn With Key Fob Lock

This feature will cause the horn to chirp when the doors are locked with the Key Fob. This feature can be turned on or turned off. To change the current setting, proceed as follows:

For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Push the LOCK button on a programmed Key

Fob for at least 4 seconds, but no longer than 10

seconds. Then, push the button while still holding the LOCK button.

2.Release both buttons at the same time.

3.Test the feature while outside of the vehicle by pushing the LOCK button on the Key Fob with the ignition in the LOCK position and the key removed.

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pushing the LOCK button on the Key Fob while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Push the UNLOCK button to deactivate the Vehicle Security Alarm.

Flash Lights With Remote Key Lock/Unlock

This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the key fob. This feature can be turned on or turned off. To change the current setting, proceed as follows:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal

Settings (Customer-Programmable Features)” in “Un-

2

derstanding Your Instrument Panel” for further infor-

 

mation.

For vehicles not equipped with the EVIC, perform the following steps:

1.Push and hold the UNLOCK button on a programmed key fob for at least 4 seconds but no

longer than 10 seconds. Then, push and hold the

LOCK button while still holding the UNLOCK button.

2.Release both buttons at the same time.

3.Test the feature while outside of the vehicle by pushing the LOCK / UNLOCK buttons on the key fob with the ignition in the LOCK position and the Key removed.

24THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pushing the LOCK button on the key fob while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Push the UNLOCK button to deactivate the Vehicle Security Alarm.

Using The Panic Alarm

To turn the Panic Alarm feature ON or OFF, push and hold the button on the Key Fob for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.

The Panic Alarm will stay on for three minutes unless you turn it off by pushing the button a second time or if the vehicle speed is 5 MPH (8 km/h) or greater.

NOTE: When you turn off the Panic Alarm by pushing the button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system.

Programming Additional Key Fobs

Refer to “Sentry Key” in “Things To Know Before Starting” for further information.

If you do not have a programmed key fob, contact your authorized dealer for details.

Key Fob Battery Replacement

NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

The recommended replacement battery is CR2032.

1.If the Key Fob is equipped with a screw, remove the screw. With the Key Fob buttons facing down, use a flat blade screwdriver to pry the two halves of the Key

Fob apart. Make sure not to damage the elastomer seal during removal.

Separating Case Halves

2.Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

3.To reassemble the Key Fob case, snap the two halves together.

NOTE: If the Key Fob is equipped with a screw, reinstall 2 and tighten the screw until snug.

General Information

The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause undesired operation.

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Obstruc-

tions between the vehicle and key fob may reduce this range.

NOTE:

The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.

Obstructions between the vehicle and the key fob may reduce this range.

How To Use Remote Start

All of the following conditions must be met before the engine will remote start:

Gear selector in PARK

Doors closed

Hood closed

Hazard switch off

Brake switch inactive (brake pedal not pushed)

Ignition key removed from ignition

Battery at an acceptable charge level

PANIC button not pushed

System not disabled from previous remote start event

Vehicle Security Alarm not active

WARNING!

Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled.

Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped

The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely:

Remote Start Aborted — Door Open

Remote Start Aborted — Hood Open

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

Remote Start Aborted — L/Gate Open

Remote Start Aborted — Fuel Low

2

Remote Start Aborted — System Fault

The EVIC message stays active until the ignition is placed in the ON/RUN position.

To Enter Remote Start

Push and release the REMOTE START button on the key fob twice within five seconds. The vehicle doors will lock, the parking lights will flash, and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle.

NOTE:

The park lamps will turn on and remain on during Remote Start mode.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode.

If your power door locks were unlocked, Remote Start will automatically lock the doors.

The engine can be started two consecutive times (two 15-minute cycles) with the key fob. However, the ignition must be placed in the ON/RUN position before you can repeat the start sequence for a third cycle.

Remote Start will also cancel if any of the following occur:

The engine stalls or RPM exceeds 2500.

Any engine warning lamps come on.

Low Fuel Light turns on.

The hood is opened.

The hazard switch is pushed.

The transmission is moved out of PARK.

The brake pedal is pushed.

To Exit Remote Start Mode Without Driving The Vehicle

Push and release the REMOTE START button one time or allow the engine to run for the entire 15minute cycle.

NOTE: To avoid unintentional shut downs, the system will disable the one time push of the REMOTE START button for two seconds after receiving a valid Remote Start request.

To Exit Remote Start Mode And Drive The Vehicle

Before the end of the 15-minute cycle, push and release the UNLOCK button on the key fob to unlock the doors and disarm the Vehicle Security Alarm (if

Loading...
+ 557 hidden pages