Jeep Wrangler 2013 Owner Manual

0 (0)
Jeep Wrangler  2013 Owner Manual

2 0 1 3 Wrangler

OW N E R ’ S M A N UA L

Includes Wrangler Unlimited

 

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

Copyright © 2012 Chrysler Group LLC

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

1

CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . .

.4

WARNINGS AND CAUTIONS . . . . . . . . . . . . . .

8

ROLLOVER WARNING . . . . . . . . . . . . . . . . . . . .

5

VEHICLE IDENTIFICATION NUMBER . . . . . . . .

8

HOW TO USE THIS MANUAL . . . . . . . . . . . . . .

6

VEHICLE MODIFICATIONS/ALTERATIONS . . . .9

4 INTRODUCTION

INTRODUCTION

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

This is a specialized utility vehicle. It can go places and perform tasks that conventional passenger cars are not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle.

The two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle.

Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive.

As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision. Refer to “On-Road/Off-Road Driving Tips” in “Starting And Operating” for further information.

This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold.

When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR® parts, and cares about your satisfaction.

INTRODUCTION 5

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate 1 than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger cars. It is capable of performing better in

a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity and the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not.

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

6 INTRODUCTION

Rollover Warning Label

Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

INTRODUCTION 7

1

8 INTRODUCTION

WARNINGS AND CAUTIONS

This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears underbody, on the right side of the frame rail near the center of the vehicle, as well as on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.

Vehicle Identification Number

NOTE: It is illegal to remove or alter the VIN plate.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

INTRODUCTION 9

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

 

2

A WORD ABOUT YOUR KEYS . . . . . . . . . . . .

.15

Ignition Key Removal . . . . . . . . . . . . . . . . . .

.15

Key-In-Ignition Reminder . . . . . . . . . . . . . . . .

16

STEERING WHEEL LOCK — IF EQUIPPED . . . .17

To Manually Lock The Steering Wheel . . . . . . .

17

To Release The Steering Wheel Lock . . . . . . . . .

17

Automatic Transmission Ignition Interlock

 

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

SENTRY KEY® . . . . . . . . . . . . . . . . . . . . . . . .

.18

Replacement Keys . . . . . . . . . . . . . . . . . . . .

.19

Customer Key Programming . . . . . . . . . . . . .

.20

General Information . . . . . . . . . . . . . . . . . . . .

21

VEHICLE SECURITY ALARM — IF

 

EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

Rearming The System . . . . . . . . . . . . . . . . . . .

21

To Arm The System . . . . . . . . . . . . . . . . . . . .

22

To Disarm The System . . . . . . . . . . . . . . . . . .

22

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

ILLUMINATED ENTRY — IF EQUIPPED . . . . .

.23

REMOTE KEYLESS ENTRY (RKE) — IF

 

EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24

To Unlock The Doors And Swing Gate . . . . . . .

24

Remote Key Unlock On First Press . . . . . . . . . .

24

To Lock The Doors And Swing Gate . . . . . . . . .

25

Sound Horn On Lock . . . . . . . . . . . . . . . . . . .

26

Using The Panic Alarm . . . . . . . . . . . . . . . . . .

26

To Turn Off Flash Lights With Lock . . . . . . . . .

27

Programming Additional Transmitters. . . . . . . .

27

General Information . . . . . . . . . . . . . . . . . . . .

28

Transmitter Battery Replacement . . . . . . . . . . .

28

REMOTE STARTING SYSTEM — IF

 

EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .

.29

How To Use Remote Start . . . . . . . . . . . . . . .

.30

DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

Upper Half Door Window Removal — If

 

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Upper Half Door Window Installation — If

 

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Front Door Removal . . . . . . . . . . . . . . . . . . . .

33

Rear Door Removal (Four-Door Models) . . . . . .

35

DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . . .

38

Manual Door Locks . . . . . . . . . . . . . . . . . . . .

38

Power Door Locks — If Equipped . . . . . . . . . .

40

Child-Protection Door Lock System — Rear

 

Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . .42

WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . .

. .43

Power Windows — If Equipped . . . . . . . . .

. .43

Wind Buffeting . . . . . . . . . . . . . . . . . . . . .

. .45

REAR SWING GATE . . . . . . . . . . . . . . . . . . .

. .45

OCCUPANT RESTRAINTS . . . . . . . . . . . . . .

. .47

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . .

. .50

Rear Center Lap/Shoulder Belt Retractor

 

Lockout — Four-Door Models Only . . . . . . .

. .55

Lap/Shoulder Belt Untwisting Procedure . . . . .56

Adjustable Upper Shoulder Belt Anchorage

. . .56

Seat Belts In Passenger Seating Positions . . . .

. .57

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

13

Automatic Locking Retractor Mode (ALR) — If

 

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .

.58

Energy Management Feature . . . . . . . . . . . . .

.59

 

2

Seat Belt Pretensioners . . . . . . . . . . . . . . . . . .

60

Enhanced Seat Belt Use Reminder System

 

(BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .

60

Seat Belts And Pregnant Women . . . . . . . . . . .

61

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .

61

Supplemental Restraint System (SRS) —

 

Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

Air Bag Deployment Sensors And Controls . . . .

67

Event Data Recorder (EDR) . . . . . . . . . . . . . . .

74

Child Restraints . . . . . . . . . . . . . . . . . . . . . . .

75

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS . . . .99

SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .100

Transporting Passengers . . . . . . . . . . . . . . . . .100

Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .100

Safety Checks You Should Make Inside The

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101

Periodic Safety Checks You Should Make

 

Outside The Vehicle . . . . . . . . . . . . . . . . . . .

103

A WORD ABOUT YOUR KEYS

The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice.

Ignition Key Removal

1.Place the shift lever in PARK (if equipped with an automatic transmission).

2.Turn the ignition switch to the ACC (ACCESSORY) position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

Ignition Switch Positions

1

— LOCK

3

— ON/RUN

2

— ACC (ACCESSORY)

4

— START

 

 

 

 

3.Push the ignition key inward.

4.Turn the ignition key to the LOCK position, and remove the key.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the Key Fob from the ignition. When leaving the vehicle, always lock your vehicle.

Never leave children alone in a vehicle, or with access to an unlocked vehicle.

Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.

Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

WARNING! (Continued)

Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.

CAUTION!

An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition sounds a signal to remind you to remove the key.

NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.

(Continued)

STEERING WHEEL LOCK — IF EQUIPPED

Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved approximately a half turn in either direction, and the key is not in the ignition, the steering wheel will lock.

To Manually Lock The Steering Wheel

With the engine running, rotate the steering wheel one– half revolution from the straight ahead position, turn off the engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

To Release The Steering Wheel Lock

Insert the key in the ignition, and turn the wheel slightly to the left or right, to disengage the lock.

NOTE: If you turned the wheel to the right to engage the 2 lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.

Automatic Transmission Ignition Interlock System

This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON/RUN position, and the brake pedal is depressed.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

SENTRY KEY®

The Sentry Key® Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.

NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the Vehicle Security Light begins to flash after the bulb check, it indicates that someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

CAUTION!

The Sentry Key® Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

All of the keys provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key® is programmed to a vehicle, it cannot be programmed to any other vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

CAUTION!

 

Always remove the Sentry Keys® from the vehicle and

 

lock all doors when leaving the vehicle unattended.

2

 

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.

NOTE: When having the Sentry Key® Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Customer Key Programming

If you have two valid Sentry Keys®, you can program new Sentry Keys® to the system by performing the following procedure:

1.Cut the additional Sentry Key® Transponder blank(s) to match the ignition switch lock cylinder key code.

2.Insert the first valid key into the ignition switch. Turn the ignition switch to the ON/RUN position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.

3.Insert the second valid key into the ignition switch. Turn the ignition switch to the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

4.Insert a blank Sentry Key® into the ignition switch. Turn the ignition switch to the ON/RUN position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off.

The new Sentry Key® is programmed. The Remote Keyless Entry (RKE) transmitter will also be programmed during this procedure.

Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key®, contact your authorized dealer for details.

NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.

General Information

The Sentry Key® system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference that may cause undesired operation.

VEHICLE SECURITY ALARM — IF EQUIPPED

The Vehicle Security Alarm monitors the vehicle doors, swing gate, and ignition for unauthorized operation. While the Vehicle Security Alarm is armed, interior switches for door locks are disabled. The Vehicle Security Alarm provides both audible and visible signals when alarming. The horn will sound, the headlights will turn on, the park lamps and/or turn signals will flash repeatedly for three

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

minutes. If the disturbance is still present (driver’s door,

 

passenger door, other doors, ignition) after three minutes,

 

the headlights, park lamps and/or turn signals will flash

 

for an additional 15 minutes.

2

NOTE: The Panic Alarm and the Vehicle Security Alarm are quite different. Please take a moment to activate the Panic Alarm and the Vehicle Security Alarm to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

Rearming The System

If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Arm The System

The Vehicle Security Alarm will set when you use the Remote Keyless Entry (RKE) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the Vehicle Security Light (located on the instrument cluster) will flash rapidly for about 16 seconds to signal that the Vehicle Security Alarm is arming. During this 16-second arming period, opening any door or the swing gate will cancel the arming. If the Vehicle Security Alarm is successfully set, the Vehicle Security Light will flash at a slower rate to indicate the Vehicle Security Alarm is armed.

To Disarm The System

To disarm the Vehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter, or turn the ignition switch to the ON/RUN position.

If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times and the exterior lights blink three times when you unlock the doors. Check the vehicle for tampering.

The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the Vehicle Security Alarm will arm unexpectedly. If you remain in the vehicle and lock the doors with the RKE transmitter, once the Vehicle Security Alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, press the UNLOCK button on the RKE transmitter to disarm the Vehicle Security Alarm. You may also accidentally disarm the Vehicle Security Alarm by unlocking the driver’s door with the key and then locking it. The door will be locked but the Vehicle Security Alarm will not arm.

NOTE:

Unlocking the doors with the manual door lock plungers or the driver’s door lock cylinder will not disarm the Vehicle Security Alarm.

When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.

ILLUMINATED ENTRY — IF EQUIPPED

The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.

This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for further information.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned to ON/RUN from the OFF position.

NOTE:

2

The front courtesy overhead console and door courtesy lights will turn on if the dimmer control is in theDome ON position (extreme top position).

The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat” position (extreme bottom position).

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED

This system allows you to lock or unlock the doors, swing gate, and activate the Panic Alarm from a maximum distance of 66 ft (20 m) using a Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.

Three Button RKE Transmitter

NOTE: The line of transmission must not be blocked with metal objects.

To Unlock The Doors And Swing Gate

Press and release the RKE transmitter UNLOCK button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the RKE transmitter UNLOCK button is pressed, the Illuminated Entry will initiate and the parking lights will flash twice.

Remote Key Unlock On First Press

This feature lets you program the system to unlock either the driver’s side, or all doors and swing gate on the first press of the UNLOCK button on the RKE transmitter.

For vehicles equipped with an Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, the Remote Unlock feature can be enabled or disabled by performing the following steps:

1.Press and hold the LOCK button on a programmed RKE transmitter.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

Security Alarm activated will cause the alarm to sound. Press the RKE transmitter UNLOCK button to deactivate the Vehicle Security Alarm.

5.If the desired programming was not achieved or to 2 reactivate this feature, repeat the above steps.

2.Continue to hold the RKE transmitter LOCK button NOTE: Pressing the LOCK button on the RKE transmitfor at least four seconds, but not longer than 10 secter while you are inside the vehicle will activate the

onds, then press and hold the RKE transmitter UNLOCK button.

3.Release both buttons at the same time.

4.Test this feature while outside of the vehicle by pressing the LOCK/UNLOCK button on the RKE transmitter.

NOTE: Pressing the RKE transmitter LOCK button while you are inside of the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle

Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.

To Lock The Doors And Swing Gate

Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signals will flash and the horn will chirp once to acknowledge the lock signal.

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Sound Horn On Lock

This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows:

For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Press the RKE transmitter LOCK button for 4 to 10 seconds.

2.While the LOCK button is pressed (after four seconds), press the RKE transmitter PANIC button. Release both buttons.

The “Sound Horn On Lock” feature can be reactivated by repeating this procedure.

Using The Panic Alarm

To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is activated, the headlights will turn on, the park lights will flash, the horn will pulse on and off and the interior lights will turn on.

The Panic Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time, or if the vehicle speed is 5 mph (8 km/h) or greater.

NOTE: When you turn off the Panic Alarm by pressing the PANIC button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system.

To Turn Off Flash Lights With Lock

This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows:

For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Press the RKE transmitter UNLOCK button for 4 to 10 seconds.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

3.Test the “Flash Lights With Lock” feature outside of the vehicle by pressing the RKE transmitter LOCK button with the ignition in the LOCK position and the

key removed.

2

NOTE: Pressing the RKE transmitter LOCK button while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the RKE transmitter UNLOCK button to deactivate the Vehicle Security Alarm.

The “Flash Lights With Lock” feature can be reactivated by repeating this procedure.

Programming Additional Transmitters

Refer to Sentry Key® “Customer Key Programming.”

2.While the UNLOCK button is pressed, (after four If you do not have a programmed RKE transmitter, seconds) press the RKE transmitter LOCK button. contact your authorized dealer for details.

Release both buttons.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

General Information

This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference that may be received including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If your RKE transmitter fails to operate from a normal distance, check for these two conditions:

1.Weak battery in the RKE transmitter. The expected life of a battery is five years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.

Transmitter Battery Replacement

The recommended replacement battery is CR2032.

NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

1.With the RKE transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the RKE transmitter apart. Use extreme care not to damage the seal or internal components.

Loading...
+ 636 hidden pages