Jeep Liberty 2011 User Manual

0 (0)

2 0 1 1 Liberty

O W N E R ’ S M A N U A L

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

Copyright © 2010 Chrysler Group LLC

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. .9

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

93

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

215

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

309

5

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

421

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

441

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

491

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

507

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

517

10

INTRODUCTION

1

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

Warnings And Cautions . . . . . . . . . . . . . . . . . . .

7

Rollover Warning . . . . . . . . . . . . . . . . . . . . . . .

4

Vehicle Identification Number . . . . . . . . . . . . . .

7

How To Use This Manual . . . . . . . . . . . . . . . . . .

5

Vehicle Modifications/Alterations . . . . . . . . . . . .

8

4 INTRODUCTION

INTRODUCTION

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold.

When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR parts, and cares about your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over when some other vehicles may not.

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle

control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Rollover Warning Label

Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing

INTRODUCTION 5

seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by 1 two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

6 INTRODUCTION

INTRODUCTION 7

WARNINGS AND CAUTIONS

 

 

This Owner’s Manual contains WARNINGS against op-

 

1

erating procedures that could result in a collision or

 

 

 

bodily injury. It also contains CAUTIONS against proce-

 

 

dures that could result in damage to your vehicle. If you

 

 

do not read this entire manual, you may miss important

 

 

information. Observe all Warnings and Cautions.

 

 

VEHICLE IDENTIFICATION NUMBER

 

 

The Vehicle Identification Number (VIN) is found on the

 

 

left front corner of the instrument panel. The VIN is

 

 

visible from outside of the vehicle through the wind-

 

 

shield. This number also is stamped into the right front

Vehicle Identification Number

door sill (under the molding) and appears on the Auto-

NOTE: It is illegal to remove or alter the VIN.

mobile Information Disclosure Label affixed to a window

 

 

on your vehicle, the vehicle registration, and the title.

 

 

8 INTRODUCTION

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

 

2

 

A Word About Your Keys . . . . . . . . . . . . . . . . .

12

Ignition Key Removal . . . . . . . . . . . . . . . . . .

12

Key-In-Ignition Reminder . . . . . . . . . . . . . . .

14

Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Replacement Keys . . . . . . . . . . . . . . . . . . . . .

16

Customer Key Programming . . . . . . . . . . . . .

16

General Information . . . . . . . . . . . . . . . . . . .

17

Vehicle Security Alarm — If Equipped . . . . . . . .

18

Rearming Of The System . . . . . . . . . . . . . . . .

18

To Arm The System . . . . . . . . . . . . . . . . . . .

18

To Disarm The System . . . . . . . . . . . . . . . . .

19

Illuminated Entry . . . . . . . . . . . . . . . . . . . . . .

20

Remote Keyless Entry (RKE) . . . . . . . . . . . . . .

20

To Unlock The Doors And Liftgate . . . . . . . . .

21

To Lock The Doors And Liftgate . . . . . . . . . .

22

To Unlatch The Liftgate Flipper Glass . . . . . . .

24

Remote Open Window Feature —

 

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .

24

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Using The Panic Alarm . . . . . . . . . . . . . . . . .

24

Programming Additional Transmitters . . . . . .

25

Battery Replacement . . . . . . . . . . . . . . . . . . .

25

General Information . . . . . . . . . . . . . . . . . . .

26

Remote Starting System — If Equipped . . . . . . .

27

How To Use Remote Start . . . . . . . . . . . . . . .

27

Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .

29

Manual Door Locks . . . . . . . . . . . . . . . . . . .

29

Power Door Locks . . . . . . . . . . . . . . . . . . . .

30

Child-Protection Door Lock System —

 

Rear Doors . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35

Power Windows . . . . . . . . . . . . . . . . . . . . . .

35

Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .

39

Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39

Liftgate Flipper Glass . . . . . . . . . . . . . . . . . .

40

Occupant Restraints . . . . . . . . . . . . . . . . . . . . .

41

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .

44

Lap/Shoulder Belt Untwisting Procedure . . . .

50

Seat Belt Pretensioner . . . . . . . . . . . . . . . . . .

50

Seat Belt Lock Out . . . . . . . . . . . . . . . . . . . .

51

Seat Belts In Passenger Seating Positions . . . . .

51

Automatic Locking Retractor Mode (ALR) —

 

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .

51

Supplemental Active Head Restraints (AHR) . . 52

Enhanced Seat Belt Use Reminder System

(BeltAlert ) . . . . . . . . . . . . . . . . . . . . . . . . .

56

Energy Management Feature . . . . . . . . . . . . .

58

Seat Belts And Pregnant Women . . . . . . . . . .

58

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .

58

Supplemental Restraint System (SRS) —

 

Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .

59

Air Bag Deployment Sensors And Controls . . .

64

Event Data Recorder (EDR) . . . . . . . . . . . . . .

76

Child Restraints . . . . . . . . . . . . . . . . . . . . . .

77

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

 

Engine Break-In Recommendations . . . . . . . . . .

87

 

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .

87

 

 

 

 

Transporting Passengers . . . . . . . . . . . . . . . .

87

2

. . . . . . . . . . . . . . . . . . . . . . . . .Exhaust Gas

88

 

Safety Checks You Should Make Inside The

 

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

89

 

Periodic Safety Checks You Should Make

 

 

Outside The Vehicle . . . . . . . . . . . . . . . . . . .

91

 

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

You can insert the double-sided keys into the locks with either side up.

The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place.

Ignition Key Removal

Automatic Transmission

Place the shift lever in PARK. Turn the key to the ACC position and then push the key and cylinder inward slightly and rotate the key to the LOCK position. Then remove the key.

Vehicle Key

Jeep Liberty 2011 User Manual

Ignition Switch Positions

1

— Lock

3

— On

2

— Acc

4

— Start

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

NOTE:

For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), features such as the power

window switches, radio, power sunroof or Sky Slider 2 (if equipped), and power outlets will remain active for

45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.

For vehicles equipped with the EVIC, features such as the power window switches, radio, power sunroof or Sky Slider (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.

Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.

CAUTION!

An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key.

NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.

SENTRY KEY

The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.

NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the Vehicle Security Light begins to flash after the bulb check, it indicates that

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal 2 vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

CAUTION!

The Sentry Key Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

All of the keys provided with your new vehicle have been programmed to the vehicle electronics.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Replacement Keys

NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming

procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.

NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.

Customer Key Programming

If you have two valid Sentry Keys , you can program new Sentry Keys to the system by performing the following procedure:

1.Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.

2.Insert the first valid key into the ignition switch. Turn the ignition switch to the ON/RUN position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.

3.Insert the second valid key into the ignition switch. Turn the ignition switch to the ON/RUN position within

15seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

4.Insert a blank Sentry Key into the ignition switch. Turn the ignition switch to the ON/RUN position within

60seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off.

The new Sentry Key is programmed. The Remote

Keyless Entry (RKE) transmitter will also be programmed during this procedure.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key , contact your authorized dealer for details.

NOTE: If a programmed key is lost, see your authorized 2 dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference that may cause undesired operation.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

VEHICLE SECURITY ALARM — IF EQUIPPED

The Vehicle Security Alarm monitors the vehicle doors, liftgate, and liftgate flipper glass for unauthorized entry and ignition for unauthorized operation. While the Vehicle Security Alarm is armed, interior switches for door locks and flipper glass are disabled.

If something triggers the alarm, the Vehicle Security Alarm will sound the horn intermittently, the headlights, park lamps and/or turn signals and the Vehicle Security Light in the instrument cluster will flash for three minutes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights, park lamps and/or turn signals will flash for an additional 15 minutes.

NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case

one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

Rearming Of The System

If something triggers the Vehicle Security Alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.

To Arm The System

1.Remove the key from the ignition switch and exit the vehicle.

2.Lock the doors and liftgate by pressing the power door LOCK switch or the LOCK button on the Remote Keyless Entry (RKE) transmitter.

NOTE: The Vehicle Security Alarm will not arm if you lock the doors with the manual door lock plungers or the driver’s door lock cylinder.

3. Close all doors. The Vehicle Security Light in the instrument cluster will flash rapidly for about 16 seconds to signal that the Vehicle Security Alarm is arming. During this period, opening any door or the liftgate will cancel the arming process. If the Vehicle Security Alarm is set successfully, the Vehicle Security Light will flash at a slower rate to indicate the alarm is armed.

NOTE: For added security, whenever the Security Alarm is armed, the HomeLink /Garage Door Opener (if equipped) is disabled as well.

To Disarm The System

Either press the UNLOCK button on the RKE transmitter or insert a valid Sentry Key into the ignition lock cylinder and turn the key to the ON/RUN position.

NOTE:

Unlocking the doors with the manual door lock plungers or the driver’s door lock cylinder will not disarm the Vehicle Security Alarm.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.

The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the 2 Vehicle Security Alarm will give you a false alarm. If the previously described arming sequence has occurred, the Vehicle Security Alarm will arm regardless of whether you are inside or outside the vehicle. If you remain inside the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.

Tamper Alert

If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times and exterior lights blink three times when you unlock the doors. Check the vehicle for tampering.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

ILLUMINATED ENTRY

The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.

This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for further information.

The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned to ON/RUN from the OFF position.

NOTE:

The front courtesy overhead console and door courtesy lights do not turn on if the dimmer control is in the Dome ON position (extreme top position).

The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat” position (extreme bottom position).

REMOTE KEYLESS ENTRY (RKE)

This system allows you to lock or unlock the doors and liftgate, open the liftgate flip-up window, or activate the PANIC alarm from distances up to approximately 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. However, the line of transmission must not be blocked with metal objects when using the RKE transmitter.

NOTE: Inserting the key into the ignition switch disables all buttons on the RKE transmitter.

Vehicle Key

To Unlock The Doors And Liftgate

Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

Remote Key Unlock, Driver Door/All Doors First

This feature lets you program the system to unlock either the driver’s door or all doors and the liftgate on the first press of the UNLOCK button on the RKE transmitter. To 2 change the current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Press and hold the LOCK button on a programmed (i.e., functional) RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the UNLOCK button while still holding the LOCK button.

2.Release both buttons at the same time.

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3.Test the feature from outside the vehicle by pressing the LOCK and UNLOCK buttons on the RKE transmitter.

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

Illuminated Approach — If Equipped

This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

To Lock The Doors And Liftgate

Press and release the LOCK button on the RKE transmitter to lock all doors and the liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the lock signal.

Sound Horn With Lock

This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Press the LOCK button on a programmed (i.e., functional) RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button.

2.Release both buttons at the same time.

3.Test the feature from outside the vehicle by pressing the LOCK button on the RKE transmitter.

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

Flash Lights With Lock

The feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change 2 the current setting, proceed as follows:

For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

For vehicles not equipped with the EVIC, perform the following steps:

1.Press and hold the UNLOCK button on a programmed (i.e., functional) RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button.

2.Release both buttons at the same time.

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3.Test the feature from outside the vehicle by pressing the LOCK and UNLOCK buttons on the RKE transmitter.

4.Repeat these steps if you want to return this feature to its previous setting.

NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.

To Unlatch The Liftgate Flipper Glass

Press the FLIPPER GLASS button twice to unlatch the liftgate flipper glass.

WARNING!

To avoid injury stand back when opening. Glass will automatically rise.

Remote Open Window Feature — If Equipped

This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely.

Using The Panic Alarm

NOTE: The PANIC and Security Alarms are quite different. Please take a moment to activate the PANIC and the Security modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

To turn the PANIC Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the PANIC Alarm is on, the headlights and turn signal lights will flash, the horn will pulse on and off, and the illuminated entry system will turn on.

The PANIC Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater.

During the PANIC Mode, the door locks and Remote Keyless Entry (RKE) system will function normally. PANIC mode will not disarm the Security System on vehicles so equipped.

NOTE: You may need to be close to the vehicle when using the RKE transmitter to turn off the PANIC Alarm due to the radio frequency noises emitted by the system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

25

 

Programming Additional Transmitters

 

 

Refer to Sentry Key “Customer Key Programming.”

 

 

If you do not have a programmed RKE transmitter,

 

2

contact your authorized dealer for details.

 

Battery Replacement

The recommended replacement battery is CR2032.

NOTE:

Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Do not touch the battery terminals that are on the back housing or the printed circuit board.

1. Remove the screw from the RKE transmitter case (if equipped).

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. With the RKE transmitter buttons facing down, use a flat blade tool to pry the two halves of the RKE transmitter case apart. Make sure not to damage the seal during removal.

Separating Case Halves

3.Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

4.To reassemble the RKE transmitter case, snap the two halves together.

5.Reinstall and tighten the screw until snug (if equipped).

General Information

This device complies with Part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference that may be received including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If your RKE transmitter fails to operate from a normal distance, check for these two conditions:

1.Weak battery in RKE transmitter. The expected life of the battery is from one to two years.

2.Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of

approximately 300 ft (91 m).

NOTE: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

How To Use Remote Start

All of the following conditions must be met before the engine will remote start:

Shift lever in PARK.

2

 

Doors closed.

Hood closed.

Liftgate closed.

Hazard switch off.

Brake switch inactive (brake pedal not pressed).

Ignition key removed from ignition switch.

Battery at an acceptable charge level.

RKE PANIC button not pressed.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled.

Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

To Enter Remote Start Mode

Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the

engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle.

NOTE:

For security, power window operation and sunroof or Sky Slider operation (if equipped) is disabled when the vehicle is in the Remote Start mode.

The engine can be started two consecutive times (two 15-minute cycles) with the RKE transmitter. However, the ignition switch must be cycled to the ON/RUN position before you can repeat the start sequence for a third cycle.

To Exit Remote Start Mode Without Driving The Vehicle

Press and release the REMOTE START button one time or allow the engine to run for the entire 15-minute cycle.

NOTE: To avoid unintentional shut downs, the system will disable the one-time press of the REMOTE START button for two seconds after receiving a valid Remote Start request.

Loading...
+ 512 hidden pages