Jeep Grand-Cherokee 2011 Owner's Manual

0 (0)

2 0 1 1 Grand Cherokee

O W N E R ’ S M A N U A L

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

Copyright © 2010 Chrysler Group LLC

SECTION

TABLE OF CONTENTS

PAGE

1

2

3

4

5

6

7

8

9

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INTRODUCTION

. . 3

1

 

 

 

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.11

2

 

 

 

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101

3

 

 

 

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

243

4

 

 

 

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

337

5

 

 

 

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

461

6

 

 

 

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

481

7

 

 

 

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

537

8

 

 

 

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

553

9

 

 

 

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

563

10

INTRODUCTION

1

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

Warnings And Cautions . . . . . . . . . . . . . . . . . . .

8

Rollover Warning . . . . . . . . . . . . . . . . . . . . . . .

5

Vehicle Identification Number . . . . . . . . . . . . . .

8

How To Use This Manual . . . . . . . . . . . . . . . . . .

6

Vehicle Modifications/Alterations . . . . . . . . . . . .

9

4 INTRODUCTION

INTRODUCTION

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

This is a specialized utility vehicle, it can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle.

The two-wheel drive utility vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle.

Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmission,

and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive.

As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision. Refer to “On-Road/Off-Road Driving Tips” in “Starting And Operating” for further information.

This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold.

When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR parts, and cares about your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger cars. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over when some other vehicles may not.

INTRODUCTION 5

Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle 1 control. Failure to operate this vehicle safely may result

in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.

Rollover Warning Label

6 INTRODUCTION

Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment

The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

INTRODUCTION 7

8 INTRODUCTION

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.

INTRODUCTION 9

VEHICLE MODIFICATIONS/ALTERATIONS

1

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death.

VIN Location

NOTE: It is illegal to remove or alter the VIN.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

 

2

 

A Word About Your Keys . . . . . . . . . . . . . . . . .

14

Wireless Ignition Node (WIN) . . . . . . . . . . . .

14

Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Removing Key FOB From Ignition . . . . . . . . .

16

Key-In-Ignition Reminder . . . . . . . . . . . . . . .

18

Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . .

19

Replacement Keys . . . . . . . . . . . . . . . . . . . . .

20

Customer Key Programming . . . . . . . . . . . . .

20

General Information . . . . . . . . . . . . . . . . . . .

20

Vehicle Security Alarm — If Equipped . . . . . . . .

21

Rearming The System . . . . . . . . . . . . . . . . . .

21

To Arm The System . . . . . . . . . . . . . . . . . . .

21

To Disarm The System . . . . . . . . . . . . . . . . .

22

Illuminated Entry . . . . . . . . . . . . . . . . . . . . . .

23

Remote Keyless Entry (RKE) . . . . . . . . . . . . . .

23

To Unlock The Doors . . . . . . . . . . . . . . . . . .

24

To Lock The Doors . . . . . . . . . . . . . . . . . . . .

25

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Remote Open Window Feature —

 

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .

25

Using The Panic Alarm . . . . . . . . . . . . . . . . .

26

Programming Additional Transmitters . . . . . .

26

Transmitter Battery Replacement . . . . . . . . . .

26

General Information . . . . . . . . . . . . . . . . . . .

28

Remote Starting System — If Equipped . . . . . . .

29

How To Use Remote Start . . . . . . . . . . . . . . .

29

Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Power Door Locks . . . . . . . . . . . . . . . . . . . .

34

Child-Protection Door Lock System —

 

Rear Doors . . . . . . . . . . . . . . . . . . . . . . . . . .

35

Keyless Enter-N-Go . . . . . . . . . . . . . . . . . . . . .

36

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41

Power Windows . . . . . . . . . . . . . . . . . . . . . .

41

Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .

44

Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44

Liftgate Flipper Glass . . . . . . . . . . . . . . . . . .

45

Power Liftgate — If Equipped . . . . . . . . . . . .

46

Occupant Restraints . . . . . . . . . . . . . . . . . . . . .

48

Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .

52

Lap/Shoulder Belt Operating Instructions . . . . 53

Lap/Shoulder Belt Untwisting Procedure . . . . 57

Adjustable Upper Shoulder Belt Anchorage . . . 57

Energy Management Feature . . . . . . . . . . . . . 58

Seat Belts In Passenger Seating Positions . . . . . 59

Automatic Locking Retractor Mode (ALR) —

 

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .

60

Seat Belt Pretensioners . . . . . . . . . . . . . . . . .

61

Supplemental Active Head Restraints

 

(AHR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

Enhanced Seat Belt Use Reminder System

 

(BeltAlert ) . . . . . . . . . . . . . . . . . . . . . . . . .

65

Seatbelt Lock Out . . . . . . . . . . . . . . . . . . . . .

67

Seat Belts And Pregnant Women . . . . . . . . . .

67

Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .

67

Supplemental Restraint System (SRS) —

 

Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68

Advanced Front Airbag Features . . . . . . . . . .

70

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

13

 

Airbag Deployment Sensors And Controls . . .

74

 

Event Data Recorder (EDR) . . . . . . . . . . . . . .

81

 

 

 

 

Child Restraints . . . . . . . . . . . . . . . . . . . . . .

82

2

. . . . . . . . . .Engine Break-In Recommendations

95

 

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .

96

 

Transporting Passengers . . . . . . . . . . . . . . . .

96

 

Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .

97

 

Safety Checks You Should Make Inside The

 

 

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98

 

Periodic Safety Checks You Should Make

 

 

Outside The Vehicle . . . . . . . . . . . . . . . . . .

100

 

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up.

Keyless Enter-N-Go Feature

This vehicle is equipped with the Keyless Enter-N-Go feature, refer to “Starting Procedures” in “Starting And Operating” for further information.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three of which are detented and one spring-loaded. The detented positions are OFF, ACC, and ON/RUN. The START position is a spring-loaded momentary contact position. When released from the START position, the switch automatically returns to the detented ON/RUN position.

NOTE: With the Keyless Enter-N-Go feature, the Electronic Vehicle Information Center (EVIC) will display the ignition switch position (OFF/ACC/RUN). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.

Jeep Grand-Cherokee 2011 Owner's Manual

Wireless Ignition Node (WIN)

1 — OFF

2 — ACC (ACCESSORY)

3 — ON/RUN

4 — START

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

Key Fob

The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- 2 tion. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.

The emergency key allows for entry into the vehicle on the driver’s side should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking.

NOTE: Entering a vehicle using the emergency key with the theft alarm armed, will result in the alarm sounding. Insert the Key Fob (even if the Key Fob battery is dead) into the ignition switch to disarm theft alarm.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.

Emergency Key Removal

NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.

Removing Key Fob From Ignition

Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob.

With the Keyless Enter-N-Go feature, the EVIC will display the ignition switch position “OFF/ACC/RUN”. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.

NOTE:

If you try to remove the Key Fob before you place the shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the Key Fob as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the Key Fob cannot be removed until you obtain service.

The power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the OFF position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

CAUTION!

 

If your vehicle battery becomes low or dead, your

2

Key Fob will become locked in the ignition.

Do not attempt to remove the Key Fob while in this condition, damage could occur to the Key Fob or ignition module. Only remove the emergency key for locking and unlocking the doors.

Leave the Key Fob in the ignition and either:

Jump Start the vehicle.

Charge the battery.

Contact your dealer for assistance on how to remove the Key Fob using the manual over ride method.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Key-In-Ignition Reminder

Opening the driver’s door when the Key Fob is in the

 

Never leave children alone in a vehicle. Leaving ignition and the ignition switch position is OFF or ACC, unattended children in a vehicle is dangerous for a sounds a signal to remind you to remove the Key Fob.

number of reasons. A child or others could be

NOTE: The Key-In-Ignition reminder only sounds

seriously or fatally injured. Do not leave the Key

when the Key Fob is placed in the OFF or ACC ignition

Fob in the ignition or Keyless Enter-N-Go in the

position.

ACC or ON/RUN mode. A child could operate

With the Keyless Enter-N-Go feature, opening the driv-

power windows, other controls, or move the vehicle.

Do not leave children or animals inside parked

er’s door when the vehicle’s ignition switch is placed in

ACC or ON/RUN (engine stopped) will cause the re-

vehicles in hot weather. Interior heat build-up may

cause serious injury or death.

minder chime to sound. Refer to “Starting Procedures” in

 

“Starting And Operating” for further information.

 

CAUTION!

An unlocked car is an invitation to thieves. Always remove Key Fob from the ignition and lock all doors when leaving the vehicle unattended.

SENTRY KEY

The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses the factory-mated Key Fob with Remote Keyless Entry (RKE) transmitter and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine.

After turning the ignition switch to the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

the bulb check, it indicates that someone used an invalid Key Fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal 2 vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

CAUTION!

The Sentry Key Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.

All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Replacement Keys

NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended.

With Keyless Enter-N-Go, always remember to place the ignition in OFF.

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.

Duplication of Key Fobs may be performed at an authorized dealer, this procedure consists of programming a blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.

NOTE: When having the Sentry Key Immobilizer system serviced, bring all vehicle Key Fobs with you to the authorized dealer.

Customer Key Programming

Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.

General Information

The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference that may be received, including interference that may cause undesired operation.

VEHICLE SECURITY ALARM — IF EQUIPPED

This Vehicle Security Alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation. When the alarm is activated, the interior switches for door locks, power liftgate and flipper glass are disabled. The Vehicle Security Alarm provides both audio and visual signals, the horn will sound, the headlights, park lamps and/or turn signals will flash repeatedly for three minutes. If the disturbance is still present (driver’s door, passenger door, other doors, ignition) after three minutes, the headlights, park lamps and/or turn signals will flash for an additional 15 minutes.

NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

Rearming The System

If something triggers the alarm, and no action is taken to 2 disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.

To Arm The System

Vehicles Not Equipped With Keyless Enter-N-Go

The alarm will set when you use the Remote Keyless Entry (RKE) transmitter to lock the doors and liftgate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the Vehicle Security Light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the Vehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

cancel the arming. If the Vehicle Security Alarm successfully arms, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set.

Vehicles Equipped With Keyless Enter-N-Go

Press the Keyless Enter-N-Go Start/Stop button until the Electronic Vehicle Information Center (EVIC) indicates that the vehicle ignition is “OFF” (refer to “Starting Procedures” in “Starting And Operating” for further information). Then either press the power door LOCK switch while the driver or passenger door is open, press the lock button on the front driver or passenger door handle with a valid key fob in range, or press the Remote Keyless Entry (RKE) transmitter LOCK button (refer to “Keyless Enter-N-Go” in “Things To Know Before Starting Your Vehicle” for further information).

To Disarm The System

Vehicles Not Equipped With Keyless Enter-N-Go

To disarm the Vehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter or turn the ignition switch to the ON/RUN position. If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.

The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the Vehicle Security Alarm will arm unexpectedly. If you remain in the vehicle and lock the doors with the RKE transmitter, once the Vehicle Security Alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, press the UNLOCK button on the RKE transmitter to disarm the Vehicle Security Alarm. You may also accidentally sound the Vehicle Security Alarm by unlocking the driver’s door with the key and then opening the door.

Vehicles Equipped With Keyless Enter-N-Go

Either press the UNLOCK button on the RKE transmitter, pull on the front driver or passenger door handle (refer to “Keyless Enter-N-Go” in “Things To Know Before Starting Your Vehicle” for further information) with a valid key fob in range, or press the Keyless Enter-N-Go Start/ Stop button (requires at least one valid Key Fob in the vehicle), or insert a valid Key Fob into the ignition switch (if the Start/Stop button is removed) and rotate it to the ON/RUN position.

ILLUMINATED ENTRY

The interior lights come on when you open any door or use the Remote Keyless Entry (RKE) transmitter to unlock any door. They will remain on for approximately 30 seconds after all doors are closed then fade to off.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

The lights also will fade to off if you turn on the ignition after you close all the doors. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your In- 2 strument Panel” for further information.

NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually.

REMOTE KEYLESS ENTRY (RKE)

This system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables the system from responding to any button presses from that RKE transmitter. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmitter buttons for all RKE transmitters.

To Unlock The Doors

Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock all doors. The turn signal lamps will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

Refer to “Keyless Enter-N-Go” under “Things To Know Before Starting Your Vehicle” for further information.

Remote Key Unlock, Driver Door/All Doors First Press

This feature lets you program the system to unlock either the driver’s door or all doors, on the first press of the UNLOCK button on the RKE transmitter. To change the current setting, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Program- mable Features)” in “Understanding Your Instrument Panel” for further information.

Key Fob with Four-Button RKE Transmitter

Flash Lamps With Remote Key Lock

This feature will cause the turn signal lamps to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or off. To change the current setting, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.

Turn Headlights On With Remote Key Unlock

This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

To Lock The Doors

 

Press and release the LOCK button on the RKE transmit-

 

ter to lock all doors. The turn signal lamps will flash and

2

the horn will chirp to acknowledge the signal.

Refer to “Keyless Enter-N-Go” under “Things To Know Before Starting Your Vehicle” for further information.

Sound Horn With Remote Key Lock

This feature will cause the horn to chirp when the doors are locked with the RKE transmitter or the Passive Entry feature. The horn chirp feature can be turned on or off. To change the current setting, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.

Remote Open Window Feature — If Equipped

This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely.

Using The Panic Alarm

To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lamps will flash, the horn will pulse on and off, and the interior lights will turn on.

The Panic Alarm will stay on for three minutes unless you turn it off by either pressing the PANIC button a second time, or drive the vehicle at a speed of 15 mph (24 km/h) or greater.

NOTE: The interior lights will turn off if you turn the ignition switch to the ACC or ON/RUN position while the Panic Alarm is activated. However, the exterior lamps and horn will remain on.

Programming Additional Transmitters

Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.

Transmitter Battery Replacement

The recommended replacement battery is one CR2032 battery.

NOTE:

Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Do not touch the battery terminals that are on the back housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.

Emergency Key Removal

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

2. Insert the tip of the emergency key or a #2 flat blade

 

screwdriver into the slot and gently pry the two halves of

 

the RKE transmitter apart. Make sure not to damage the

2

seal during removal.

Inserting Emergency Key Into Slot

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Separating RKE Transmitter

3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.

4. To assemble the RKE transmitter case, snap the two halves together.

General Information

This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Loading...
+ 557 hidden pages